Search Documents

By F. Habashi

In the period 1970-1995, a number of hydro metallurgical processes to treat copper concentrates to overcome the pollution problem due to S02 emission in smelters were developed. Pilot and commercial scale plants were built and operated for some time, but eventually all were abandoned a few years later. It is constructive to examine why these processes were abandoned after so much expenditure of funds and effort, so that errors should not be repeated in the future and lessons from the past are learned.

Jan 1, 2007

By T. H. Etsell, P. C. Holloway

Vanadium is concentrated in the fly ash which is produced as a solid waste from oil sands operations in northern Alberta. Although a process flowsheet using sodium chloride as a roasting reagent has been developed at the University of Alberta, recent studies examine the p otential o f p otassium o r c alcium s alts a s alternative reagents for roasting Suncor fly ash to recover vanadium. Suncor fly ash was roasted with CaO, Ca(OH)2, CaCO3, CaSO4.2H2O and KC1 at 750, 850 and 950°C. Water leach extractions for the calcium compounds were low (<45%); leaching with 100 g/L Na2CO3 gave maximum extractions of 56 to 69% at 950°C. Ash roasted with KCI behaved similarly to ash roasted with NaCl. These tests indicate that similar roasting conditions (25 to 30% KCI, 850°C, and 2 to 4h) could be used to achieve similar water leach extractions (75 to 85%). However, the lower solubility of KVO3 in solution, compared to NaVO3, would make the use of KCI instead of NaCl less attractive from a process and economic standpoint. Mineralogically, leucite (KAlSi3O8) was the predominant phase in ash roasted with KCl while, in crystalline samples of ash roasted with calcium compounds, anorthite (CaAl2Si2O8) and pseudobrookite (Fe2TiO5) were identified. Ash roasted below 950°C with the calcium compounds remained poorly crystalline.

Jan 1, 2004

By P. L. Lehoux, R. F. Lopes

"Unanticipated low recovery or extraction of gold from heap leachable are can often be attributed 10 phenomena such as non-uniform percolation (channelling) of solution through heaps, excessively slow percolation rates due to densification of ore during stacking on the pads and parasitic or competing reactions of the cyanide solution with undesirable elements or geochemical ""impurities"" in the ore. The nature and causes of these phenomena are discussed in this paper, and it is suggested that geotechnical and geochemical expertise can contribute significantly to a better understanding of the relationship between laboratory results and actual field performance of the leaching process. Recommendations are made for bench-scale metallurgical testing to be complemented by geochemical and geotechnical laboratory evaluations, to ensure more successful heap leach projects. IntroductionHeap leaching is a simple, low-cost method of recovering metals from low grade ores which has now come into widespread application particularly for gold and silver metals in the United States.The heap leach process involves percolating a lixiviant (leaching agent) solution through broken or crushed ore (Chamberlain and Pojar, 1984). In the case of gold a dilute sodium cyanide solution is used and crushed ore is ""heaped"" on specially prepared impervious pads.The potential for use of heaping leaching methods for northwestern Ontario gold deposits was discussed by Beard (1983), who suggested that the use of this extraction technique in Canada should grow significantly for low grade ores as well as for small high grade deposits which cannot justify the installation of a new mill or the use of remote custom milling facilities. Two other potential situations for lise of a heap leaching extraction method are : as a low capital cost cash generator in the opening phase of a larger new project, and as a low cost output augmenter to complement a milling operation."

Jan 1, 1989

By Gema Ribeiro Olivo

The hydrothermal Au-Pd deposits are hosted by the jacutinga in the Lake Superior-type iron-formation of the Itabira Group, Minas Supergroup. Jacutinga is a highly sheared, metamorphosed, hydrothermally altered iron-formation composed of hematite, magnetite, quartz, talc and phlogopite (Cauê) or muscovite (Conceição) and minor tourmaline, palladian gold, arsenopalladinite, mertierite II and palladeisite (hydrothermal) and native gold, native palladium Pd-Cu-oxides, and kaolinite (weathering products). The highest concentrations of Pd-Au occur in quartz and hematite veins parallel to the S1 foliation (Corpo Y, CorpoX, Aba Leste and Central orebodies, at Cauê and a single orebody at Conceição) or parallel to the S2 foliation (Aba Norte). The average ore grade is 30-40 g/t Au+Pd. The characteristics of the Au-Pd ore favor an epigenetic model for gold and palladium concentration in the iron-formation. During the D1 deformation and peak metamorphism, the oxiziding, acid and hot hydrothermal fluids transported Au and Pd preferentially as chloride complexes. The reaction of the fluid with the dolomitic carbonate (the probably protolith of the jacutinga) would have dissolved carbonate and K-feldspar to form muscovite or phlogopite and tourmaline, resulting in an increase in solution pH and a decrease of Cl concentration and subsequent deposition of gold and palladium minerals.

May 1, 2003

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

Arsenical bearing deposits are posing an increasing challenge for the mining industry. In particular, mineral processing of arsenical sulfidic ores for base and precious metals recovery tend to produce problematic arsenical tailings. This arsenic being present as sulphide or oxide, tends to dissolve, contaminating surface and underground waters. To meet the environmental regulations, it is often required to stabilize the arsenic in a more insoluble form. Dundee Sustainable Technologies has developed a new patented technology using vitrification of the arsenic oxide in an economical way, giving a stable solid, well below the environmental regulations upon leaching. This technology involves oxidation of As (III) to As (V), by using a low cost natural oxidizer and transformation of the produced arsenic oxide into calcium arsenate, which is not volatile at the melting temperature of the glass. This technology would be advantageously applied on most cases around the world where sulphide concentrates are oxidized in a fluidized bed or smelted.

Jan 1, 2014

By M. Uszko

Methane drainage and ventilation methods of methane hazard mitigation are used in the coal mines of Kompania Weglowa S.A. Over 22% of methane released during mining activities is captured by methane drainage systems and transported to the surface. In this article we present development plans for utilization of methane captured and transported to the surface by methane drainage systems. The results of research on the possibility of economic utilization of methane concentrated in ventilation air that leaves the mine through fan diffusers are also described.

Aug 1, 2013

By B. Dubreuil

Arsenical bearing deposits are posing an increasing challenge for the mining industry. In particular, mineral processing of arsenical sulfidic ores for base and precious metals recovery tend to produce problematic arsenical tailings. This arsenic being present as sulphide or oxide, tends to dissolve, contaminating surface and underground waters. To meet the environmental regulations, it is often required to stabilize the arsenic in a more insoluble form. Nichromet has developed a new patented technology using vitrification of the arsenic oxide in an economical way, giving a stable solid, well below the environmental regulations upon leaching. This technology involves oxidation of As (III) to As (V), by using a low cost natural oxidizer and transformation of the produced arsenic oxide into calcium arsenate, which is not volatile at the melting temperature of the glass. This technology would be advantageously applied on most cases around the world where sulphide concentrates are oxidized in a fluidized bed or smelted.

Aug 1, 2013

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By Pierre Montrueil, Marcel St-Amant

Within the next few years, underground mobile equipment will be partially automated. Mining methods will integrate more and more automation. Such an evolution will be possible only if adequate underground communication systems are developed. This is expected due to the available competence in Canadian telecommunication, to the economic pressure on the Canadian mining industries for international competitiveness and to the social changes where a better working environment (i.e. less accidents) becomes a major concern. CCARM propose the concept of a Production Area Network for Automated Mobile Units called PANAMU as an intermediate size communication system. It can be implemented using mature present-day technology and it can be integrated in some mine wide communication systems. It can evolve so as to incorporate new technologies because of its modular concepts. In this paper, the communication requirements are estimated, the amtmptions are defined, the concepts of the PANAMU are presented and an over- view of its implementation is described. CCARM presents this article to the mining industry as a document for discussion.

Jan 1, 1994

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

By Christina Graf

A synthesis of colloidal gold shell particles with a silica core is described. Small gold nanoclusters were attached to the functionalized surface of colloidal silica particles. Reductive growth and coalescence of these clusters lead to the formation of a closed gold layer. By variation of the thickness of this gold layer and the radius of the shell it is possible to adjust the plasmon resonance of the gold shell particles over the whole visible and infrared region of the spectrum. The optical properties of the particles made are in good agreement with theoretical calculations for coreshell particles. Due to their low polydispersity these gold shell particles form in solution large crystals with submicron lattice constants. It is also possible to produce hollow gold shells by dissolution of the silica core. A new method to coat the silica core gold shell particles with an additional outer silica shell is also presented. This allows due to a reduction in the Van-der-Waals forces to make more permanent dried crystals and facilitates functionalization of the particles for use in various photonic applications.

Oct 1, 2003

By P. Coulombe, J-F. Riverin, A. Gaboury

Cavity cleaning during anode change generates a material that consists of anode cover material and cryolite melts. This material is scooped and placed in bins for transport and further processing and recycling as fresh anode cover material. Typical processing methods in use involve cooling of the hot cavity bath in bins, with or without emission treatment systems, until it is adequate to be processed and grinded to the required particle size distribution. Handling of the hot and cooled cavity bath material can be labour intensive. It also generates significant air emissions which contain particulate and gaseous fluorides. With the advent of the Aluminerie Alouette smelter Phase II expansion, the hot cavity bath tonnage to be processed increased to 700 t/day and maintaining existing practices was not satisfactory. This article presents a novel process implemented at the Alouette smelter where cavity bath is processed as a hot material directly from the potlines ( 600-800°C range), sized, cooled and then processed in the existing cold bath treatment plant. The system is designed to process 36 t/h, is fully automated and requires limited monitoring from operations. Implementing this new system in a Browrifield environment imposed numerous constraints for space, interfaces with existing operations, commissioning and ramp-up. It is presently operating at approximately 80% availability and is easily meeting the requirements of the potlines. This system has significantly improved the workplace environment in the bath treatment area and reduced the overall particulate and gaseous fluorides emissions at Alouette. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By J. E. Marshall

"The concept of employing a project management team to coordinate all aspects of the construction of a new resource development has gained wide acceptance. This team can be formed from within the staff of large mining companies or contracted from major engineering firms and consultants. The mandate of the project managers usually terminates on successful startup of the operation. For frontier mineral developments in the Canadian Arctic or in the developing countries, startup and the initial year of operation represents the period in which the project is most vulnerable to technical, political and managerial problems. A complete change of the management team or the retention of the construction project managers and the resulting cost combined with the breakdown of organizational accountability within the operating staff .are unnecessary management problems.Independent project management services provide the commitment necessary to sustain the continuity of management through all project phases. Efficiency and the ability to make decisions quickly are characteristics of the many successful small mining companies. These qualities are necessary in the project management group, which will be responsible for up to 90% of the preproduction costs.Continuous project management in the construction and operational phases of a mineral development are common in the iron ore industry, but remain anomalous in the base metal, energy mineral and industrial mineral fields.The Nanisivik project on Baffin Island in the Canadian Arctic is used to illustrate the advantages of total project management through construction and operation.Total project management has further potential for foreign interests and financial and utility organizations desirous of participating in the Canadian mining industry, but with no direct involvement in the construction or operating management. Participation agreements in the operating phase of a project can be negotiated to have management fees related to both the production and the profits of the enterprise."

Jan 1, 1980

By F. Kapeller, G. Herget

"The need for monitoring the effect of changes in ground stresses due to mining in hard rock has existed for many years. The Mining Research Laboratories of CANMET, EMR have developed a new tool which monitors with high precision the radial deformation in boreholes. The result is the Mining Research Laboratories strain monitoring system (MSMS) which uses the highly stable and very sensitive vibrating wire principle to monitor deformations in relatively large boreholes, e.g. 76 mm to 153 mm diameter.The vibrating wire is strung across a relatively large proving ring and operates at a frequency between 600 to 1800 Hz. The read-out system is based on continuous vibration.The ring is installed with a hydraulic tool and brought into contact with the surrounding rock through precisely machined and guided wedges. The resolution of the system is in the neighbourhood of 4 x 10-4 min/ Hz. The data collection can be carried out with a portable read-out unit and provisions are available for automatic data collection. Stresses may be calculated from strain readings.The system was tested in cooperation with the Centre de recherches minérales at the Niobec Mine in Quebec for the purpose of monitoring the effects of drill drift development and slope mining on surrounding ground stresses.After access was available to the site, 153 mm diameter holes were drilled for the determination of in situ ground stresses. These holes were then used to install the strain monitoring system. The effect of drill drift development and production blasting in stopes C-203-13 and C-203-15 on ground stress distribution could be observed clearly.The horizontal relaxation in the core of a pillar which occurred during mining of adjacent rooms was between 0.082 mm to 0.111 mm. Calculations of stresses from these deformations indicate that the rock material is still in an elastic condition.Roctest of Montreal has obtained a license on the manufacturing and distribution rights. A patent has been registered and CANMET will assist in installation of the MRL strain monitoring system and the interpretation of records."

Jan 1, 1989

By M. L. Free

Laboratory scale extraction of metals from heterogeneous materials such as copper ores is often performed using fine material to increase kinetics and reduce sample size requirements and costs. In contrast, commercial extraction is usually accomplished using much larger material sizes than are used in laboratory settings. The large size difference between laboratory testing and commercial application materials makes it difficult to use laboratory test data to accurately predict performance for commercial material. One solution adopted widely in industry is the use of large test columns. Large test columns cost considerably more to set up and run and take much longer periods of time to evaluate than laboratory scale tests with small particles. Consequently, from a cost and data collection efficiency perspective, the development of accurate scale up methods offers significant potential for saving both time and money. This paper provides details for a new approach to correct for scale-up phenomena in heterogeneous material processing.

Jan 1, 2007

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019

By James F. A. Hatley

Northern Saskatchewan comprises an area of about 350 000 km2 and boasts some of the world&apos;s largest known high-grade uranium deposits. The successful mining of these deposits, however, can not be accomplished without overcoming technical challenges. Not only is the high grade of the uranium ore challenging, but mining methods need to be developed to deal with groundwater at very high pressures, and ground conditions that vary substantially from excellent to wholly unconsolidated clays and sand. This paper discusses the various mechanisms of inflows at the three of the Cameco Corporation Mines in Northern Saskatchewan. The risk of inflows is quantified in terms of unique challenges from hydrogeologic conditions, rockmass integrity, and uncertainty in geologic conditions. Mitigation strategies in case of an inflow are also briefly described. The paper concludes by addressing the impact of institutional rules (corporate standards) on minimizing, monitoring, and controlling the probability and/or impact of unexpected inflows.

Aug 1, 2010

By Takahiko Okura, Chiharu Tokoro, Shunta Shibuya

Copper concentrates bearing arsenic as enargite (Cu3AsS4) or tennantite (Cu12As4S13) have disadvantage on copper smelting environmentally and economically, so those concentrates should be treated decently. In this paper, some experiments of arsenic removal from several kinds of copper concentrates by heat treatment in an inert atmosphere were discussed. In this study, several samples in which arsenic contents varied 0.18 to 8.3 wt % were heated to the temperature range of 400 °C to 700 °C under argon gas flow during 1 hour. The heat residues and volatilized materials (V.M.) were analyzed by XRD, XRF, ICP-AES, XAFS and MLA to analyze residual concentration of arsenic and residual mineral composition. Experimental results showed that arsenic removal from copper concentrates advanced in 2 steps; at the temperature range of 500 ° C to 550 °C and of 550 °C to 650 °C, respectively. MLA analysis showed that a few of arsenic in enargite was removed by 550 °C heating and a majority of it was still combined with copper and sulfur as tennantite. On the other hand, arsenic in tennantite was removed almost completely by 650 °C heating. Furthermore, a particular type of arsenic mineral, such as Cobaltite (CoAsS) still remained after heating at 700 °C.

Jan 1, 2014

By R. D. Brown

"AbstractOver the past five years, tax rates in the Canadian mining industry have skyrocketed upward across Canada, as both federal and provincial governments have sought to increase their share of mining revenues.However, the past few years have not only brought high tax rates to the industry, but also a number of important new federal and provincial tax incentives.In large part, these incentives ~ special credits or reduction in tax for carrying out specific exploration, processing or other activities - have helped to moderate the adverse effects of the higher tax rates and have provided inducements for exploration and processing activities which might not otherwise have been undertaken.However, the effectiveness of certain of these incentives can be questioned: our over-all tax structure now consists in large part of punitively high marginal rates with some extraordinarily generous but capricious tax reductions for specific activities and may not be in the best long-term interest of either the industry or the nation.A rational tax structure, with moderate and stable tax rates, together with reasonable incentives confined to activities specifically requiring them, could be a more effective spur to investment than the present tax and incentive jungleIntroductionIN THE YEARS since federal tax reform, the mining industry in Canada has faced a continued escalation in its tax burdens as federal and provincial governments have leapfrogged each other in imposing new and higher taxes on the industry. The result has been that marginal tax rates imposed on mining and processing activities throughout Canada have jumped to hitherto unparalleled levels."

Jan 1, 1977

By K. Enns, J. J. Byerley

"While thiocyanate (SCN-) is used in a number of industrial processes (production of polyacrylonitrile filaments, synthesis of agricultural chemicals and certain metallurgical solvent extraction and flotation circuits) it is recognized more as an undesirable by-product associated with &apos; the metallurgical industry. Thiocyanate is present at low concentrations in some waste streams from the iron and steel industry. Of particular significance is the formation of thiocyanate during cyanidation of gold and silver ores, concentrates, tailing s and residues. The thiocyanate levels present in the resulting effluents may range from a few mg/I to several thousand mg/I.At present, thiocyanate does not appear to be as hazardous in the environment as cyanide (CN-) at the same concentration although its interaction with other species and resulting decomposition of products may be unacceptable. Of course the presence of thiocyanate in the leaching circuit and ultimately in the effluent streams may add considerably to the oxidative requirments of any non-selective treatment process for cyanidation wastes.With respect to the thiocyanate as it relates to the cyanidation process, two aspects are evident. Thiocyanate forms and persists in the cyanidation circuit resulting in a ""fouling"" condition with subsequent loss of leaching activity. In order to reduce or control this problem, it is common practice for some mills to discharge daily as much as 20% of the barren leach liquor. Besides contributing to fouling of the leach liquor the formation of thiocyanate represents an irreversible loss of reagent cyanide. It is noteworthy that in some present or proposed mill practice reagent cyanide loss through thiocyanate formation may reach 50%(1). The purpose of this paper is to discus s the application of controlled electrooxidation of thiocyanate with the view of suggesting a process for regenerating cyanide from waste thiocyanate(2). The paper describes the important theoretical aspects and presents experimental data obtained for thiocyanate electrooxidation using both small and large scale electrochemical reactors. Some economic conclusions are presented."

Jan 1, 1984