Search Documents

By E. H. Kranck

Introduction Baffin Island is still too in-accessible to be of interest to the mining industry. However, twenty years ago few people dreamed of mining iron ?ore in Labrador. A journey by air to the most remote places in the Arctic is today no more remarkable than a trip to Europe, and the technical difficulties of mining minerals of high value are not insurmountable. Some ?observations concerning the geology and mineral possibilities of Baffin Island, the largest of the Arctic islands, may therefore interest the members of the Institute, in spite of problematic practical value of the subject. The following short account is mainly based on observations made during the Baird Expedition of the Arctic Institute of North America last summer 1950), and on information available from earlier expeditions. Early Work Baffin Island was one of the first parts of Canada to attract prospectors. Frobisher sent a shipload of rocks, which he believed contained precious metals, from Baffin Island to England. This attempt, however, was a failure and no further serious prospecting work has, so far as I know, been done. During the past few years geological mapping has been carried out by the Geological Survey of Canada (Fortier. Davison, 1949-1950) in the southern parts ?of the island, along the coast of Hudson strait. In 1942, Weeks mapped the coast from Pangnirtung to the head of Cumberland fiord, and Netteling river up to Netteling lake. In the northern parts of the island, only scattered observations have been made ?by Bell, Watkins, Baird, and others.

Jan 1, 1951

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By Bob Rappolt

Discussion Points Part 1: Global Mining Industry/Related Issues ? Historical Metal Price Trends. ? Historical LME Metal Stockpiles. ? China?s Demand for Metal. ? World Population Growth, Demands and Development. Discussion Points (cont?d) Part 2: Canadian Mining Industry ? Where are we? And where are we going? ? What progress have we made in the past 20 years regarding: ? Safety -Employee Levels ? Labour -Relative Compensation ? Productivity - Technological Advance ? Where do we stand regarding mineral production? ? What does the future hold for us?

Apr 1, 2005

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By Bradley Stoughton

The magnetic oxide of iron, F eO4 , contains a theoretically larger amount of iron ( 72.4 per cent.) than any other commercial ore. It is probable that it has originated in many cases by the prolonged exposure of the hydrated oxide, ZF e20 a + 3H20 to heat and pressure which converts it first into hematite, F e20 3, and then into magnetite. It would thus appear as if nature had already done part of the work of removing all the oxygen and that magnetite should be relatively easy to reduce. That it is, in fact, less reducible than either limonite or hematite, is due chiefly to its dense and compact physical structure, which makes it less pervious to the furnace gases, and also to its characteristic action in resisting crushing to a uniform size, with consequent irregularity in reducing conditions within the furnace. The net result is that the magnetic oxide requires more fuel and more time for its reduction in the blast-furnace than any other iron ore of similar iron content and physical condition. There is another very important reason why the smelting of magnetite is more costly than that of hematite, and its treatment viewed with a great deal of adverse prejudice by blast furnace operators, namely, that magnetite decreases the proportion of heat developed by the fuel in the stack of the furnace, and increases the already excessive heat requirements of the heart.

Jan 1, 1924

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By L. D. Smith

"The economic evaluation of a mineral project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation. The list that is presented below is intended to act as a checklist for the person who develops and reviews an evaluation, and as a shopping list for the persons gathering data at the project site.There are varying degrees of detail required at the different stages of evaluation in a project, from the ""quick and dirty"" overview, to the pre-feasibility study, to a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in a project and can be used for all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the reviewer can then pursue in more detail using increasingly more comprehensive checklists for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation."

Jan 1, 1994

By J-F. Magnan, M-A. Thibault, R. Boulianne, C. Gauthier, J-P. Gagné, G. Dufour

During the production of aluminium in smelters, the anodes used in electrolysis cells have to be replaced frequently. Anode butts are usually placed on anode trays for transportation and cooling, a practice during which Hydrogen Fluoride (HF) is emitted in large quantities. Covers developed in 2000 by Alcoa Deschambault to fit on the anodes trays were implemented, resulting in significant reductions of HF emissions. However, the covers are expensive to maintain and use short-life consumable parts. In January 2004, STAS and Alcoa decided to develop a more efficient design of cover, with lower maintenance costs and no need for consumable materials (like soft cushions). This paper presents a summary of the work performed to develop the new design as well as a summary of the test results.

Jan 1, 2006

By M. Sakamoto

Copper foil is an indispensable material for Printed Circuit Boards (PCBs). PCBs in turn are essential elements of all electronic equipment today and thus important for our living in the new age of IT. The requirements from the copper foil market have lately been increasingly strict and diversified due to the rapid technical advancements in miniaturized high-density electronic equipment and highly integrated semiconductors. Tight control of thickness, metallurgical properties, surface morphology and characteristics is needed. In this paper, both electrodeposited copper foil for PCB and rolled copper foil for the flexible printed circuit board are discussed, and the recent technical developments in these copper foil products are reviewed.

Jan 1, 2007

By Richard E. J. Putman

THE MINERALS INDUSTRY has always been a heavy user of energy in most of its unit operations: power in the mining, comminution, flotation and electro-winning processes; fuel in its smelting and other metallurgical processes; and, of course, fuel in the on-site generation of power and steam. Many of the techniques for using computers to perform energy management and conservation tasks have been known for some time, but they have not been widely implemented because the return on investment has hitherto been insufficient. Recent trends, however, have not only caused the dollar return to rise due to higher purchased energy costs, but the cost of the investment to fall. One trend has been the generally lower cost of computer control systems themselves, due to vendors having adopted the newer, lower-cost and more reliable electronic component technologies now becoming universally available. The second trend is the development of low-cost, but high-speed, remote multiplexing devices, which have reduced considerably the expense of bringing data from points scattered over a wide area, which is typically the case when applying energy management systems to a minerals processing plant. By taking advantage of these and related developments, computer control systems can now have a rewarding impact on plant energy management and conservation practices, and recent advances in application technology have opened up new and additional opportunities for energy cost reduction and control.

Jan 1, 1978

By P. B. Demarsh

"Location: - On highway 59, 17 miles east of Val d 10r near junction of Montreal highway in Northwestern Quebec.Life; - Started production 1952, ceased 1965.Ore: - Pyrite, chalcopyrite and small amounts of free gold and goldsilver tellurides in narrow quartz-carbonate-tourmaline veins in granodiorite. Specific gravity 2, 70.Capacity: - 700 tons daily Bevcon ore supply, l 000 tons daily when custom ore available.Assay: - Heads 0 .140 oz. per ton; tails 0. 009 per ton; extraction 92.5%.Grind: - 75% minus 200 mesh at 700 tons; 68% minus 200 mesh at 1000 tons. Detention time 28 hours and 21 hours respectively.Treatment: - Cyanidation process.Reagents: - Per ton. Aero Cyanide (NaCn) 0, 50; crushed unslaked lime 1. 75; zinc 0. 03; litharge 0. 10; steel consumption 2. 25.Water: - Pumped from land-lock spring fed lake l 1/2 miles distant.Cost: - Per ton. Crushing 0. 13; grinding 0 .32; filtration 0. 07; cyanidation 0.14; miscellaneous 0.29; total 0.95.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - Predominantly French Canadian, nucleus English Canadians.Tailings: - Impounded low lying pond.Personnel: - 15 including supervision.Flow sheet: - Canadian Mining Manual l 9 5 6 .Building: - Wood truss construction: 3/ 4 in. siding, ten test and 1/ 4 in. transite outside. Corrugated galvanized iron roof. Ground level foundations. Internal self induced heating. Wood stave tank equipment."

Jan 1, 1966

By Enrique I. Acuña

Creighton Mine is part of the mining history of Sudbury with more than 100 years of operation. Currently the deeper levels of the mine are reaching the 8000 ft level without implementation of mechanical refrigeration system as a result of the use of the Natural Heat Exchange Area (NHEA) over the past decades. The NHEA of Creighton Mine is part of an old block caving area divided into 4 blocks of trenches that were used to extract the ore. Currently, it is used year round to condition the outside temperature before the airflow enters the fresh air system of the mine. As the mine is progressing deeper, underground temperatures in the lower levels are starting to approach the limit of Vale?s guidelines for working in heat. This paper presents the study developed to improve the management of the NHEA to obtain cooler temperatures at the intake of the ventilation system and outlines the impact to the mine in terms of the additional level(s) that could be operated underground without the use of mechanical refrigeration. This is another of the efforts currently under development for energy conservation and to reduce the capital and operational costs of Creighton Mine while extending the expected life of the mine.

Oct 1, 2010

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By T. C. WEBB

In New Brunswick, significant potash deposits are intimately associated with rocks of the Lower Carboniferous Windsor Group. To date, two deposits high in sylvinite, up to 20 m thick, have been confirmed at depths between 490 and 1,035 m below surface near Plumweseep and Salt Springs. These areas are currently under development by the Potash Company of America and the Denison-Potacan Potash Company respectively. A third area, near Lower Millstream, is also known to contain potash-bearing evaporites and is now being explored by BP Exploration Canada Ltd. All three areas are situated in the western half of the Moncion Subbasin and are within 25 km of Sussex. Numerous similarities in stratigraphy, thickness, mineralogy and structure suggest that deposition of evaporites throughout much of southern New Brunswick was contemporaneous and extended over a considerable area. Future opportunities for potash exploration in the province thus seem excellent. A number of large unexplored areas remain in the Moncion and Cumberland Subbasins and in parts

Jan 1, 1984

By S. A. Sadough vanini

In this paper the influence of temperature on the flow behavior and rheological characteristics of an A356 alloy in the semi-solid state using backward extrusion process are studied experimentally and numerically. Simulation process is done by dynamic explicit in ABAQUS software for each forming condition. A cooling slope treatment was employed in order to obtain a non-dendritic microstructure. Experiments were performed in 5 temperatures and 4 different wall thicknesses. In the low forming speeds, liquid fraction had time to escape from solid phase forward the samples? wall. This condition was the main reason for the segregation phenomenon seen in the base and walls. Viscosities were determined using the force-displacement graphs obtained form back-extrusion tests. As observed experimentally, in a constant temperature, increase of shear rate resulted in decrease of alloy viscosity exponentially. Raising the temperature increases the liquid fraction hence reduces the semi-solid alloy viscosity. The results of experimental and simulation are compared and there is a good adaptation.

Oct 1, 2011

By F. E. P. PEARSON

Sandstone quarried from an island in Lake Winnipeg is barged 130 km to a processing plant at Selkirk on the Red River. The stone is white, poorly consolidated, and consists of rounded quartz grains of high natural purity. It is an important supplier of silica in Western Canada for glass, fiberglass, foundry and other industrial uses.

Jan 1, 1984

By Roger Reed

It is well known that the performance and carbon emissions associated with the modern gas turbine engine depend critically upon the properties of the nickel-based superalloys, particularly those used in single crystal form. However, the design of all alloys in current use has been essentially empirical, or at best heavily reliant upon regression/neural network analysis of experimental datasets. In this paper, alloy design approaches [1] are described which are able to identify new alloy composition spaces which are worthy of experimental study. It is shown that a large amount of design data can be generated, which can be interpreted in different ways. Of course, the success of the approach depends heavily upon the accuracy of the underlying sub-models. Estimates of the creep resistance, cost, castability, density and oxidation resistance are made. It is demonstrated that these methods allow quantitative trade-offs to be made between the properties of interest.

Jan 1, 2010

By C. H. Hopper

THE gold orebodies of the Matachewan Consolidated mine are of particular interest geologically because of their odd shapes, their apparent lack of connection one with another, and the fact that they occur in a number of different formations. All of the orebodies exhibit a similar fracture pattern and the areas of fracturing appear related to the local folding. However, the lack of either horizontal or vertical continuity suggests additional controls not yet discovered. The question of origin, so ably discussed by H. C. Cooke in 1919, will be reviewed in the light of the additional evidence uncovered since his examination of surface trenches twenty-four years ago. The Matachewan Consolidated mine, with its neighbour, the Young-Davidson mine, is in Powell township, 25 miles by road northwest from Elk Lake, 30 miles west of Kirkland Lake, and 45 miles southeast of Porcupine. It may be considered as being on the westerly extension of the Kirk-land Lake sedimentary belt, where the rock column is markedly similar. There is no similarity in structure, however, for great ore-bearing shears and faults simply do not occur at Matachewan. Rather may it be said that the region, under stress, failed in isolated brecciated patches, some of which make up today's orebodies. The mine currently treats 1,000 tons a day of porphyry ore averaging 0.10 oz. gold per ton. It started operations in 1934 on greenstone ore, and the mill then treated 150 tons a day of ore averaging 0.23 oz. gold per ton. Total production to the end of 1941 has been 929,484 .tons averaging 0.160 oz. gold per ton.

Jan 1, 1942

By G. W. Davies

"IntroductionThe development of British Columbia's northeast coal deposits, represents the single biggest industrial undertaking in British Columbia's history.As a result of this development, several thousand jobs were created, hundreds of millions of dollars in new tax revenue and billions of dollars in new foreign exchange began flowing into Canada.The Northeast Coal Development began in 1981 with the signing of sales contracts to ship a total of 6.5 million tonnes of metallurgical and additional quantities of thermal coal annually to Japan over a 15-year period. The current long-term agreements contain provisions for extension to 20 years.The sales contracts with a group of Japanese steel mills were signed by two Vancouver-based mining companies, Quintette Coal Limited and Teck Corporation. The agreements followed years of exploration and negotiation beginning in 1968.The first shipment of coal from Quintette and Teck's Bullrnoose Mine was transported by BC Rail and Canadian National Railways to the Ridley Island coal port in the fall of 1983."

Jan 1, 1992

By Robert Halupka

The industrial minerals sector represents a broad range of products involving a variety of technologies serving a diversity of markets and end uses. Unit values of products vary widely, reflecting the peculiarities of each product/market sector. Generalizations are therefore understandably difficult to make and borrowers may need to take extra time to "educate" lenders on the key aspects of their business and industry sub-sector. This paper will examine the factors and the thinking that lenders apply when considering financing proposals to companies in the industrial minerals sector. If you understand the lender's perspective and their concerns, then you can make better use of your own time and resources when arranging financing for your company or project.

Jan 1, 2001