Search Documents

By Pingchao Ke, Zhihong Liu

Fe(III)-As(V) precipitates were synthesized from the Fe(II)-As(V)-SO42--H2O system at 90°C in initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The synthesis were carried out by introducing oxygen gas into the system to oxidize Fe(II) ions into Fe (III) ions, and at the same time, adding aqueous sodium carbonate solution into the system to neutralize the acid released by the hydrolysis reactions, with the purpose of keeping the pH constant at 1.5±0.05. The precipitates obtained were characterized by XRD, chemical composition analysis, SEM, XPS, and Raman spectrum. The results indicated that the particles in the precipitates were in the morphology of irregular aggregation with their sizes in the range of about 1–4 µm. The precipitates consisted of scorodite, ferric arsenate and amorphous hydrated ferric oxide, of which amorphous hydrated ferric oxide formulated as Fe(OH)x(SO42-)y. The characteristic XPS peaks of Fe-AsO43- and Fe-O in the precipitates located at 711.8 and 713.3 eV, separately, and the existence of amorphous hydrated ferric oxide led to two series of shake off lines developed over the end of high binding energy of Fe2p XPS. The precipitates were stable in TCLP tests at pH 4.93 for 60 hours with the arsenic concentrations in the leaching solutions being 0.27 mg/L and 0.59 mg/L for the precipitates prepared in the initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The tests for the long-term stability of the precipitates were carried out by leaching them for 40 days at 25°C under various media in the pH range from 9.50 to 10.57, and the results showed that the precipitates synthesized in this study were much more stable than those by previous researchers.

Jan 1, 2017

By K. Matsuura, M. Ohno, T. Tokunaga

"Recently, weight saving of automobiles has been strongly required to solve the global environmental problems. Mg alloys are one of the promising candidates as a new material for automobile components. However, the application of the Mg alloys is limited due to their poor corrosion resistance. In the authors’ preliminary study, an Al/Mg/Al clad sheet was fabricated by hot extrusion and subsequent hot forging. The clad sheet exhibited a high corrosion resistance and excellent super plasticity. More specifically, the elongation of the clad sheet was as high as 550%.Importantly, despite that the elongation of Al itself was only 40%without cladding with Mg, the ductility of Al was greatly improved in the form of the clad sheet. In the present study, in order to clarify the mechanism of the superplastic deformation of the Al part in the clad sheet, the microstructure evolution of the Al during the tensile de formation is investigated. The tensile tests were conducted at a temperature of 573 K and at a strain rateof1.0×10-3s-1. The Al exhibited fiber-type texture at the beginning of the tensile deformation, and brass-type texture after the elongation of 50%.INTRODUCTIONMg alloys have been gaining attention because of their excellent properties e.g. light weight, good recyclability and high electromagnetic shielding. However, their practical applications have been limited due to their poor corrosion resistance. In the authors’ previous study, in order to solve this problem, Al coating on Mg alloy by hot extrusion has been proposed, and the Al-coated Mg alloy plate was fabricated(Tokunaga, Matsuura, &Ohno,2012). The plate was hot-rolled and an Al/Mg/Al clad sheet was fabricated. No cracks or debondings were observed at the Al/Mg interface. The sheet exhibited a high corrosion resistance in a comparable level as pure Al. Also, the sheet exhibited a large and uniform elongation of 550%in a tensile test at a temperature of 573 K and at a strain rate of 1.0×10-3s-1without any breakings or debondings of the Al part(Tokunaga, Matsuura, &Ohno,2014).Mg alloys have been known to exhibit a superplastic characteristic when the grain size is small. However, it is known that the pure Al does not generally exhibit the super plasticity. As mentioned above, the Al-coated Mg alloy sheet exhibited 550% of elongation in the authors’ previous study (Tokunagaet al., 2014). However, the pure Al itself showed only 40% of elongation, while the Mg alloy itself exhibited 800% of elongation. Thus, it has been demonstrated that the pure Al was super plastically elongated when it was bonded with the Mg alloy. Generally, deformation mechanism of the super plasticity of the Mg alloy is known as a grain boundary sliding. On the other hand, the mechanism of the superplastic elongation of the pure Al is still unclear. The purpose of the present study is investigation of the deformation behavior of the Al part in the Al/Mg/Al clad sheet during tensile de formation."

Jan 1, 2018

By D. L. Churcher, R. J. Perry

"In recent years much work has been don e to examine alternate underground backfill support systems with the objectives of improving ground support and reducing mining costs. This report deals with the work conducted at Placer Dome Inc.’s Dome Mine to develop a high density backfill system, taking advantage of the unique properties of this fill material, to address a backlog of large open stopes to sustain stable minewide ground conditions for future generations of Dome miners.IntroductionDome Mine began its existence in 1909 with the discovery of visible gold on a dome shaped outcrop located west of Porcupine Lake in northern Ontario. The orebody beneath this outcrop has supported one of Canada’s premier gold mining operations for 80 years. Production during this time of over 46 000 000 tons of ore has resulted in the recovery of II 500 000 ounces of gold and 2 000 000 ounces of silver. Mining continues today at a production rate of 3500 tons per day, with ore coming from both underground and open pit operations.During the life of the mine, different underground mining methods have been used to extract the ore from a complex deposit consisting of single and multiple vein structures.Cut-and-fill mining was introduced in the 1930s using sand fill and later hydraulic fill for support and to provide a working platform. A total of 1 800 000 tons of sand fill and 7 300 000 tons of hydraulic fill have been placed underground in cut-and-fill stopes. Until the late 1960sshrinkage mining was used extensively, particularly in narrow, steeply dipping zones. Bulk mining with small diameter longholes was introduced about this time, to take advantage of low production costs. Longhole blasting has often been used to recover low grade ore from the walls or sills of old shrink stopes, resulting in large open stopes. Backfilling of these open holes has been restricted to smaller stopes and associated with local ground conditions.In the late 1970s it was recognized that the number of large open holes which were being generated presented serious regional and minewide stability problems for future operations. With higher gold prices, economic ore reserves were being tied up in areas adjacent to multi-level open stope complexes. To stabilize these stopes and allow access, backfilling would be required."

Jan 1, 1990

By Unknown

Diesel locomotives for underground haulage have been used in coal mines in Continental Europe for twenty-five years or more. In Great Britain, it was not until 1935 that permission was granted to use them in gassy coal mines, but since that time they have been employed in increasing numbers both in gassy and non-gassy coal mines and in metal mines. Their use underground in coal mines in the United States is still prohibited and the same was the case in Canada until 1946, when permission was granted to operate a Diesel underground in the Adanac mine of West Canadian Collieries, Limited, at Bellevue, Alberta. The locomotive used here is a 50 h.p. Hunslet Mark II. More recently, a 100 h.p. Diesel was placed in operation for underground haulage at No. 18 Colliery of the Dominion Steel and Coal Corporation, in the Sydney coalfield, N. S. Thus, on this continent, Canada has been a pioneer in the use of these locomotives underground in coal mines and there is no doubt that more and more of them will be employed as time goes on. We feel, therefore, that the following notes concerning their design and performance, which we have received from the High Commissioner for the United Kingdom, will be of interest to our members.

Jan 1, 1949

By J. T. Birkholzer, M. Rutenberg, K. -H. Lux, R. Wolters, J. Rutqvist, L. Blanco Martin

In this paper, we present numerical results corresponding to the Thermal Simulation for Drift Emplacement (TSDE) test, conducted in the Asse salt mine (Germany) between 1990 and 1999 to simulate reference repository conditions for spent nuclear fuel in rock salt. This test is of significant relevance for nuclear waste disposal in salt because extensive research and measurement programs were set up for the experiment. In our numerical study, we use two sequential simulators, TOUGH-FLAC and FLAC-TOUGH, and we investigate two-way coupled processes, focusing on thermo-mechanical analyses due to the main effect of heating. The two simulators used have recently been updated and are able to deal with large strains and creep processes. Moreover, specific constitutive relationships and coupling functions for rock salt and crushed salt under repository conditions are available. Within the framework of a benchmark exercise between Lawrence Berkeley National Laboratory and Clausthal University of Technology, the same scenario has been modeled in three dimensions using the two simulators mentioned. The main objective of the current, first stage of the benchmark is to evaluate the capabilities of these two simulators to predict relevant processes under repository conditions for high-level nuclear waste in saliniferous media. The comparison of the numerical predictions between them is very satisfactory, leading to a successful code-to-code verification. The comparison between measurements and numerical results shows that the most important processes are captured by the codes and constitutive models used. However, some differences exist between measurements and numerical results. These differences will be addressed in the next stage of the benchmark exercise, in which a parameter fitting effort will be undertaken. Overall, from the results obtained it can be concluded that TOUGH-FLAC and FLAC-TOUGH have the necessary capabilities to reproduce relevant processes under repository conditions for high-level nuclear waste in saliniferous formations.

Jan 1, 2015

By Hammenm R., J. Hammen, C. Hammen

"The production of salable Rare Earth Element (REE) products necessitates a sequence of chemical separation steps between the mine and market commodities. The effectiveness of the chemical separations that purify REE salts is critical to the success of the producer, as the purity of REE salt products affects their market price. This is due to the fact that impurities in REE salts, even at low levels, can be deleterious to the function and usability of the end product. The purification of REE by removal of low levels of contaminant has been referred to as "product polishing". The technologies commonly in use for product polishing, solvent extraction (SX) and ion exchange (IEX) are challenged by the availability of separation chemistries to separate the contaminant from the desired REE salt. In simple terms, if a product specification is 99.9% purity, the SX or IEX separation reagents need to have at least a 999:1 selectivity ratio. Significant testing has been carried out on the use of solid phase extraction (SPE) columns to extract low-level impurities such as aluminum or zinc from REE product streams. The SPE columns are nano-composite materials that have rapid equilibration kinetics with the solutes being processed by the columns. The SPE matrices have been modified with chelating ion exchange ligands that bind the contaminating ion with great selectivity in residence times of a few seconds. Thus, REE streams with 1 to 2% of contaminating aluminum ions, have been polished to >99.99% purity. In this paper, results are presented on the removal of aluminum impurity from a didymium (neodymium+praseodymium) product stream using SPE technology. The selection of the SPE medium and the process steps to treat the feed solution for aluminum removal and ultimate stripping and recycle of the solid phase extractant are discussed."

Jan 1, 2014

By A. Fakhimi

The effect of porosity on mechanical behavior of rock has been studied in the past using both experimental and numerical techniques. One important aspect of this study that has not received much attention is the role of void size and distribution on the mechanical behavior of rock. In this study, the CA2 computer program that is a hybrid discrete-finite element program for two-dimensional simulation of geomaterials is used. Numerical specimens with different macro-void sizes are loaded uniaxially. The Young?s modulus, Poisson?s ratio, uniaxial strength and crack initiation stress are studied. The numerical results are compared with the database of experimental tests on Plaster of Paris specimens containing Styrofoam spheres with different void sizes and porosities. It is shown that the macro void spatial distribution is partly responsible for the scatter of the experimental data. It is also shown that not-only the porosity but also the pore size can affect the deformability, crack initiation stress and rock strength.

May 1, 2009

By I. Stefanou, J. Sulem

"In the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface. Multiphysics couplings play a major role in earthquake nucleation and seismic slip. The effect of shear heating and thermal pressurization may be of prime importance in the control of the stability of shear deformation inside the slipping zone. Other mechanisms in relation with thermal decomposition of minerals affect the pore pressure and the temperature evolution of the system, and can play a significant role in the extreme strain localization observed in field. The actual width of the localized zone is a key parameter for understanding fault weakening mechanisms. On the basis of field observations, laboratory experiments and recent advanced modeling, these phenomena are analyzed and discussed in order to bring some new insights in the understanding of earthquakes nucleation.INTRODUCTIONIn the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface (Scholz, 1998; Sykes, 1978). The conceptual model of spring slider system is commonly used to represent the interaction between an elastic crustal block and a fault zone. Stick-slip instability is possible if the softening rate of the shear resistance of the fault zone is high enough as compared to the stiffness of the crustal block. Therefore, weakening mechanisms that can explain how the frictional resistance of a fault decreases with slip and/or slip rate is of prime importance to understand how an earthquake nucleates. In recent years, several drilling programs in active faults (e.g. the Nojima fault in Japan, Boullier, 2011; the Aigion Fault in Greece, Cornet et al. 2004, the Chelungpu fault in Taiwan, Ma et al. 2006, and the San Andreas fault in the U.S.A. Ellsworth et al. 2000) as well as high velocity friction experiments (e.g. Tanikawa et al 2012a; Tanikawa et al. 2012b) have highlighted the physico-chemical processes involved in the nucleation of seismic slip (see for the example the review paper of Niemeijer et al. 2012)."

Jan 1, 2015

By Étienne Yvenou, Martin Désilets

Le procédé d’électroaffinage du Cu est nécessaire pour atteindre les niveaux de pureté requis pour les applications les plus courantes telles que son utilisation comme conducteur électrique ou thermique.

May 2, 2024

By Charles S. Ney

"THE WRITER'S acquaintance with Kootenay King mine is limited to a brief geological excursion in the vicinity. This paper has been compiled largely from maps of J. Sullivan, mine geologist in 1952, kindly made available to the writer by Transcontinental Resources; a 1942 private report by W. L. Brown; and personal communications with J. Sullivan. Remarks on regional geology, and the comparison with Sullivan mine, are specifically the writer's.The Kootenay King mine is situated in the westernmost range of the southern Canadian Rockies at an elevation of 7,300 feet. From the Sullivan Mine at Kimberley, B. C., it lies 19 miles due east. Six miles of this distance are represented by the pronounced topographical and structural gap of the Rocky Mountain Trench. Mineral claims were locat-ed in the area prior to 1898. The deposit was first seriously explored in the late 1920s, and a small orebody was then outlined and developed. Mining and milling were undertaken in 1951.52. The orebody, amounting to about 14,000 tons, was mined out, and no significant new ore was revealed.The orebody is a replacement of dolomitic argillite by fine-grained galena, sphalerite, and pyrite. The sulphides are finely laminated in the direction of bedding, following out minor folds faithfully. The grade of ore estimated from diamond drill holes (W. L. Brown, 1942) was 11 ·I per cent zinc, 11 ·I per cent lead, and 3·8 ounces per ton of silver. The mineralized zone extends about 250 feet horizontally, 160 feet vertically, with a width of six to twenty feet.General GeologyThe country rocks are sediments of the Aldridge formation of late Precambrian age. For several thousand feet stratigraphically above and below the mine, the formation consists mainly of thinly laminated argillite and siltstone. Several horizons contain appreciable carbonate. About 2,800 feet stratigraphically below the mine, predominantly dolomitic beds mark the top of the underlying Fort Steele formation. The medium-bedded fine quartzites, which characterize about 10,000 feet of the Middle Aldridge in the Purcell range, have a restricted development amounting to only 2,000 feet in the Rocky Mountains. This member is about 2,200 feet above the mine horizon."

Jan 1, 1949

By Andrea R. Gerson, Roger St. C. Smart, Russell Schumann, Joan E. Thomas, Warwick Stewart, Stuart Miller

Sequential Net Acid Generation (NAG) accelerated oxidation testing using peroxide was carried out on single sulfide mineral samples. The calculation of the nett acid production potential (NAPP) assumes that all the sulfide is present as pyrite and that dissolution results in a 2:1 ratio of H+:SO42-. NAPP as kg H2SO4/t is calculated as 30.6 x wt.% S present. To test whether this calculation is valid a NAPP* value was defined in which instead of using the wt.% S present for the calculation the wt.% S dissolved is used. Stoichiometric analysis of the dissolution products of the sulfide minerals as they would occur at pH 7 indicates, that in all cases, the ratio of H+:SO42- of 2:1 is viable. The NAG to pH 7 and NAPP* closely coincided for pyrite, bornite, chalcocite and covellite. For the three Cu-containing minerals, the NAG to pH 4.5 value was 0 as is predicted on the basis of the speciation likely to be present at pH 4.5. Acid generation is due to hydroxylation of the dissolved Cu between pH 4.5 and 7.0. The NAG to pH 7 and NAPP* values for chalcopyrite, arsenopyrite and pyrrhotite were in reasonable agreement but were not for either sphalerite or galena. Zn is not completely hydroxylated at pH 7 as is assumed by the calculation. For galena, surface analysis identified polysulfide formation on of the leach residue polysulfide. The formation of polysulfide is an acid consuming reaction. Therefore under conditions of accelerated oxidation the NAPP value is a reasonable estimate of the possible acid production in all cases except for sphalerite and galena. However, under conditions of less intense oxidation, for instance in columns, waste rock and tailings dumps, the formation of polysulfides is likely to be more widespread thus reducing the correlation between NAPP and the maximum possible acid production.

Jan 1, 2004

By J. Ji, A. Shi, B. Grcic

Floating copper minerals selectively against iron minerals such as pyrite has been challenging for most copper and copper/gold deposits, and many operations continuously strive to maximise copper recovery whilst meeting target concentrate grades. Maximising grade is achieved by selectively floating copper minerals and rejecting pyrite. This challenge is to minimise copper and gold losses in the roughers if this approach is used. A flotation testing program was conducted by Bureau Veritas Minerals on a high-level pyrite bearing copper/gold ore sample to establish the potential to reject pyrite in the rougher stage, but also maximise copper and gold recoveries, and ultimately final product grades. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. The main variables tested for achieving selective flotation of copper and gold were collector type and pH control, through lime addition. Grind sizes used in the rougher and cleaner tests had been established from previous test work. The collectors tested were SIPX, Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The two best performing collectors were then tested in open-circuit cleaner tests, with the optimum conditions examined further in locked cycle tests. INTRODUCTION Bureau Veritas Minerals Metallurgical Division was retained by Eldorado Gold Corporation to perform a metallurgical testing program on a high-level pyrite bearing copper/gold ore sample from a gold- copper porphyry deposit to optimize flotation reagent scheme to improve gold and copper recoveries and copper content in the concentrate. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. Initially, various collectors were screened in kinetic rougher tests, and over a pH range of 8.5 (i.e the natural ore pH) up to 11.5, using a primary grind size of 80% passing 120 µm. The collectors tested were SIPX (sodium isopropyl xanthate), Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The enrichment ratio, which is the ratio of copper to sulfur in the concentrate to that in the feed, was used as proxy for rating selectivity (i.e. degree of pyrite rejection or depression).

Jan 1, 2019

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

By C. Yoo

"Geosynthetics engineering has made phenomenal advances during the last decade in areas of manufacturing as well as practical applications. As a result, geosynthetics are now being recognized as essential construction materials that can be used to facilitate construction, ensure better performance of the structures and reduce the long-term maintenance in routine civil engineering works. The creative use of geosynthetics in geo-engineering practice is expected to continuously expand as innovative materials and products are becoming available. In this paper, a wide variety of geosynthetic products available to geoengineers to solve a wide range of problems are briefly presented along with their functions and possible applications. Fundamentals of geotextile filter design principles are then introduced for use in the tunnel drainage system. Practical applications of geosynthetics relevant for tunnel engineering are also highlighted with emphasis on the issues associated with the geotextile filter application for use in the tunnel drainage system.INTRODUCTIONGeosynthetics have emerged as essential engineering materials in a wide range of civil engineering applications, e.g., transportation, geotechnical, geoenvironmental, hydraulics, and private development since the first geosynthetic conference in Paris, 1977 (Koerner 2012). Due to their costeffectiveness, ease of installation, and well established mechanical and hydraulic properties, geosynthetics are now playing important roles in the field of geo-engineering.As indicated in the 9th Bucahanan Lecture paper by Holtz (2001), major developments in civil engineering have only been possible with the parallel developments in the technology of construction materials. For example, larger scale structures became possible with the help of developments in concrete, reinforced concrete, and prestressed reinforced concrete technology which replaced wood and building stone as construction materials. The best example of a parallel development in geo-engineering between the material and the geotechnical application may perhaps be the soil reinforcement technology which has a direct analogy with reinforced concrete as a polymeric reinforcement material provides added level of tensile resistance and stability to soils that have little to no tensile strength, thus giving additional margin of safety."

Jan 1, 2015

By Perry L. Christian

"Mana/ta Coal Ltd. 's Costello Mine, located seven kilometres east of Estevan, Saskatchewan, has been operating at the present location since 1960. During the past twenty-three years, annual production of lignite coal has averaged 590 000 tonnes. The coal is used for power generation and for industrial and domestic use. Markets, operating techniques, facilities in place and reclamation are discussed. Introduction The Costello Mine (formerly the Klimax Mine) is located in southeastern Saskatchewan, approximately 210 kilometres southeast of Regina and 5 kilometres from the United States' border, as shown in Figure 1. The present mine, 7 kilometres east of the city of Estevan, has been operating since 1960. The history, however, of the Costello Mine and of the Estevan Coalfield dates from the initial settling of the area in the 1880s. Mining initially consisted of burrowing into the side of the Souris River Valley or other hillsides where the coal seam was exposed. Eventually, slopes were put down in the Estevan/Bienfait area and vigorous underground activity existed. In the late 1920s surface strip mining was introduced. The use of strip mining progressed to the point where it completely replaced underground mining in the 1950s and it is the only method in use today. During the past 23 years annual production has averaged 590 000 tonnes. The lowest production was in 1960 when the mine was starting up at 167 000 tonnes and the highest production was in 1977 when production was 1 509 000 tonnes. The Costello Mine controls approximately 11 400 hectares of mineral rights in the Estevan area. This is made up of 4 900 hectares of freehold coal and 6 500 hectares of leases. The area forms a large, irregular shaped configuration. Most holdings are contiguous and adjacent. The mine also owns some 8 400 hectares of surface rights. The lands under the Costello Mine's surface rights control, which are not being used in the mining operation, are leased to local farmers and ranchers. This ensures that the land is used to its full potential, both before and after mining."

Jan 1, 1985

By E. M. Yates, H. M. Hamilton

"For the assent of any new mining project it is essential to determine a realistic value of revenue from the sale of concentrates.A description of the market factors influencing the concentrate terms will be presented along with a detailed review of historical terms of a smelter contract for zinc concentrates. OverviewFor the assessment of any new mining project it is essential todetermine a realistic value of revenue from the sale of concentrates.This applies at all stages of assessment through to the final feasibilitystudy. In forecasting revenue for a zinc mine the followingfactors must be considered:(a) mill recovery and zinc concentrate grade;(b) metal price forecast for all payable metals;(c) smelter terms; and(d) other selling costs.Normally, data from test work are used to determine mill recovery and concentrate grade.Market forecasting, and indeed all economic prediction is an inexact science and probably will always remain so. We have our econometric models our input/output models and a lot of other tools. But they are of no help in predicting the unpredictable. OPEC's huge increase in the price of oil was certainly the most dramatic example of this. It had a tremendous effect on the cost of producing most products world wide and on the price of these products. Any forecasts made prior to the OPEC action were obviously proven wrong."

Jan 1, 1994

By Robert B. Parsons

"The junior mining company's bank account is depleted, but there are high hopes for the company's property. Where to get the necessary development funds is a common problem facing many juniors.This month, Tax Notes discusses briefly the principal income tax implications of several alternative development plans that are typically available to the junior mining company and its shareholders.IntroductionAt some point in time, many junior exploration companies face a common dilemma-a promising prospect has been proven up and is read y for further development, but alas, the company is flat broke! In this situation, a number of alternatives is available to the company, including the possibility of ""going it alone"" by raising capital through a public offering, or by striking a deal with a ""major"" or some other substantial investor.This article focuses on the latter possibility, and discusses in broad term s the main income tax implications of various arrangements between a typical junior exploration company and a larger public company for the development of a particular property. It will be appreciated that a discussion of other important considerations, such as those pertaining to securities exchange regulation s and company law requirements, is beyond the scope of this article.Jointly Owned CorporationPerhaps the simplest way of dealing with the problem of financing the development of a property is to sell the property outright, pocket the proceeds, and run! Clearly, though, this alternative is unacceptable to most prospectors and developers, who are predictably reluctant to completely relinquish their equity interest in a promising property. An additional strike against such an outright sale is that the sale could trigger an income tax liability. Generally speaking, in the case of a simple sale of a mineral property, for income tax purposes the proceeds are applied to reduce the taxpayer' s unclaimed balance of Canadian development expense (""CDE""), with any unapplied excess being brought into income and taxed at ordinary corporate tax rates."

Jan 1, 1983

By N. Nemeth

A brief summary of available filtration research is given. Its usefulness and shortcomings to practical application are examined and suggestions for new avenues of research outlined.

Jan 1, 1967

By R. J. Chase, C. Davies

"The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilimajaro International Airport and in close proximity to the towns of Moshi and Arusha. The graphite mineralization is hosted by relatively undeformed linear Proterozoic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasability studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 85 graphitic carbon. Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.In addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence"

Jan 1, 1994

By T. A. Postolski, A. J. Sinclair

"Abstract- Two examples are used to describe how geological features impact on the development of semi-variogram models to be used for geostatistical resource/reserve estimation of porphyry-type deposits. In the Main zone of the Huckleberry porphyry copper deposit, mineralization is concentrated in fracture zones localized in volcanic rocks, along the eastern and southern margins of a granitic stock. Mineralized volcanic rocks can be subdivided into three separate domains, each with its own preferred direction of mineralization that is reflected in contoured Cu diagrams and semivariograms.The East zone at Huckleberry deposit, spatially distinct from the Main zone, is controlled by a fracture zone elongate roughly east-westerly and bounded on the south by a major fault (easterly striking and steeply dipping) across which there is a dramatic drop in grades. The eastern part of the East zone appears to be coaxial with a large intrusive body; the western part contains a small, elongate dike-like intrusion. Contoured Cu values for many levels suggest that the principal direction of geological elongation of the east and west domains of the East zone differs significantly. Independently derived semi-variogram models for each domain are different and reflect this difference in trend.In both Main and East zones of the Huckleberry deposit, block estimates by ordinary kriging are significantly different using a domain-specific semi-variogram model than using a deposit-general semi-variogram model. The domain-specific estimates are deemed better because they are based on local controls of mineralization and have less conditional bias than those generated by the depositgeneral semi-variogram model."

Jan 1, 1998