Search Documents

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By C. Jay Hodgson, Adrienne C. L. Larocque

Abstract -The Mobrun VMS deposit in northwestern Quebec does not fit the classic Noranda­ type model, but exhibits characteristics more consistent with a Mattabi-type deposit. The orebodies are underlain by fragmental volcanic rocks indicative of explosive volcanism in shallow water. Felsic volcanic rocks are more abundant than mafic rocks. Alteration assemblages comprise chlorite, carbonate, sericite, and quartz. Broad semi-conformable alteration occurs high in the footwall to the 1100 lens. Mobrun occurs higher in the stratigraphic sequence than most of the other deposits in the Noranda camp. In this part of the stratigraphy, zones of pervasive carbonatization may be more useful guides for exploration than zones of silicification.

Jan 1, 1993

By W. J. Weymark

"The Gregg River project is located 40 kilometres southwest of Hinton, Alberta, adjacent to and east of Jasper National Park. This metallurgical coal mine has been developed as a joint venture between Gregg River Coal Ltd. (a subsidiary company of Mana/ta Coal Ltd.) and seven Japanese companies. This 200-million dollar project consists of a conventional truckshovel open-pit operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. Mining operations started in October 1982 with plant start-up following in April 1983. Introduction This paper is an overview and update of the Gregg River project, a metallurgical coal mine being developed as a joint venture between Gregg River Coal Ltd. (a subsidiary of Manalta Coal Ltd.) and seven Japanese companies. The Gregg River Coal leases cover 3440 hectares and are located 40 kilometres south of Hinton, Alberta, adjacent to and north of Cardinal River Coal Mine (Fig. 1). This 200-million dollar project consists of a conventional truck-shovel operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. A total of 31.5 million tonnes of clean metallurgical coal will be sold to the Japanese over a fifteen-year term. At present, mining operations are ahead of schedule and the plant started up on schedule in April 1983. Access and Climate An all-weather road, Highway 40, connects the minesite with Hinton (the nearest commercial centre) and a Canadian National Railway (C.N.R.) spur line connects the minesite with the C.N.R. main line in Edson. Hinton is accessible by road chartered airline and rail. ' ~h~ rug~ed and varied topography in the area creates large vanations m temperature and precipitation over short distances. The region is characterized by precipitation throughout the year long cold winters and short cool summers. The mean temperatur~ of the area range from a low of -14°C in January, the coldest month, to a high of 12°C in July, the warmest month. Long-term precipitation data indicates a mean yearly precipitation of 870 mm of which 620Jo occurs during the summer months."

Jan 1, 1985

By D. Fredlund

The decommissioning of uranium tailings facilities often requires the design of a suitable cover system. In northern climatic environments there is a portion each year that can be considered to be ?inactive? while the remainder of the year can be considered to be ?active?. There are numerous engineering design assumptions required when analyzing both the ?active? and the ?inactive? portions of the year. Cover systems are subjected to complex boundary conditions and nonlinear unsaturated soil properties. The proposed paper describes the steps necessary for the preparation and the analysis of a multi-year climatic database for the design of a cover system in northern environments. The paper also explains how climate can be classified and how observed variations from one year to the next can be taken into consideration in cover design. The results of climatic records at two different sites are used to illustrate conditions that need to be taken into consideration when designing soil cover systems.

Aug 1, 2010

By M. Sukhram, S. A. Argyropoulos

"In the aluminum and steel processing industries there is a need for velocity sensors to measure the flow characteristics of liquid metal. This paper will present a sensor and an inverse heat transfer technique to determine the direction of velocity in flowing liquid aluminum. Experimental research work with the sensor involving liquid aluminum was conducted, using the Revolving Liquid Metal Tank at the University of Toronto, which rotates 50 kg of liquid aluminum with velocities up to 0.35 m/s. Experimental data for various magnitude of velocity demonstrate that the sensor records different thermal profiles under different fluid flow conditions. Using the transient temperature information and the inverse technique, the direction of velocity of the molten aluminum flow field can be inferred. INTRODUCTIONOur research at the University of Toronto has focused on developing invasive sensors to determine the velocity of high temperature liquid metals. High temperature in this setting is defined at VALUES (in excess of 660 °C. The discussion which will persist in this manuscript involves detecting the direction of flow in liquid aluminum using an inverse heat transfer technique. We first reported on the sensor which is used in this article in the following two publications (Sukhram and Argyropoulos, 2011a; Sukhram and Argyropoulos, 2011b). The motivation to perform this research is due to the lack of sensors available to characterize the conditions within a high temperature liquid metal reactor/vessel. A report conducted by The Minerals Metals and Materials Society (TMS Energy 2011) has suggested that the introduction of sensors into molten metal processing environments has the potential to increase process efficiency up to 15%. Such sensors will aid in the understanding of high temperature liquid metal processing operations with the goal to implement more efficient process design and practice."

Jan 1, 2012

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By J. A. Ressinger

"The purpose of this paper is to discuss some of the differences between various methods of excavating and loading as they relate to mining operations. The intent is not to provide ""pat"" answers, but instead to raise some questions and set forth some reasonable guidelines.Specifically, the paper deals with the differences and relative merits of power shovels versus rubber-tired front-end loaders - or, carrying this further, comparing what could be called ""stationary"" loading or excavating devices to ""mobile"" types."

Jan 1, 1972

By J. Mcdvcka

Sustainable development has become a driving imperative for the resource industry as it is for the rest of the global business world. Being unsustainable is a risk no business can afford. Yet implementation of sustainable development practices beyond satisfaction of compulsory reporting is still sporadic. The current standard approaches to problem analysis and decision making are too narrow to capture the complexity of the issues at stake. Hence it is necessary to develop innovation in thinking and in doing. Those who search for ways to implement sustainable development use concepts such as Whole Systems Thinking and Eco-efficiency as well as tools like Life Cycle Analysis. Others develop their own instruments. In their effort to innovate they face both resistance and support within their organisation as well as within the industry or the wider context. This paper explores the factors that support, hinder and shape the sustainable development drive of the industry and proposes a comprehensive decision-making framework that links the goal of sustainability with the tools of sustainable development. This exploration is illustrated by a case study used in a doctoral research conducted on an engineering firm providing services to our industry.

Jan 1, 2007

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By S. Amid, D. Fisk

"Wireless technologies are permeating the mining and metals industry and enabling a myriad of benefits. With standards such as IEEE 802.11 for wireless devices and ISA100.11a for wireless field instruments protecting their investments, customers look to benefit from the cost and flexibility offered by wireless devices. Using wireless field instruments, plants are eliminating the costs associated with wired system by 50 to 70% and using these savings to install more field instruments, which, when used smartly, enables them to optimize their processes efficiency and equipment reliability. Wireless also empowers a mobile workforce by allowing them to have access to key process and maintenance data directly from the field. This paper describes how wireless can help operations and maintenance personnel to be more effective. Three case studies, illustrating how the mining and metals industry is taking advantage of the technology today, are presented:1.,Optimisation of the water recovery process using wireless2.,Field operations improvement with wireless handhelds3.,Improving fleet maintenance through wireless mobile equipment management"

Jan 1, 2011

By Lisa L. Van Loon, Neil R. Banerjee

Canada is a world leader in uranium exploration, but many deposits are located in remote regions making exploration targeting challenging. Novel approaches are needed to detect the presence of large-scale ore-forming systems and to vector toward mineralization. Boron is commonly used as a key pathfinder element associated with sandstone/unconformity-hosted and basement-hosted uranium deposits in the Athabasca Basin, but the genetic relationship remains uncertain. Alteration assemblages containing boron geochemical anomalies are commonly spatially-associated with – and possibly coeval with – uranium mineralization. Boron is commonly found in tourmaline minerals but in some portions of ore deposits the host mineral for the anomalous boron remains cryptic. Boron coordination chemistry within alteration haloes can better constrain boron host mineralogy, provide insight into the nature of the boron-uranium relationship, and thus has the potential to better constrain targets for exploration. Synchrotron-source X-ray absorption near-edge structure (XANES) spectroscopy is a direct, element-specific analysis that identifies boron coordinated in both trigonally- (BO3) and tetrahedrally-coordinated (BO4) forms. This makes XANES uniquely suited for identifying the geochemical hosts for boron that may be related to hydrothermal ore forming processes. XANES spectroscopy was conducted on whole-rock assay powders from uranium deposits across the Athabasca basin containing boron concentrations ranging from <10 ppm to >10,000 ppm. XANES directly identifies the relative amount of trigonally- (BO3) and tetrahedrally-coordinated (BO4) boron in these complex mineralogical mixtures. Our work suggests a link between boron and uranium that is likely related to the unique physiochemical characteristics of ore bearing fluids that may provide a unique vector to mineralization.

Jan 1, 2020

By Francis Breton, Daniel Larouche, Pierre Heugue, Rémi Martinez

"Nowadays, in order to fit environmental restrictions, automotive markets are demanding cast aluminum alloys working at high temperature (180–300°C). New generations of alloys are required for higher strength components in engine downsizing or start-stop systems which lead to higher loading and higher specific power and stretch current materials to their limits. Recently, transition metals, such as zirconium and vanadium, have been added as alloying elements into an AlSi7Cu3.5Mg0.1 alloy to improve physical, mechanical, thermodynamic properties with the aim of increasing service life of parts. In such alloys, the best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, including: solutionizing, quenching and artificial aging. This study is focused on the modified AlSi7Cu3.5Mg0.1 cast alloy with Mn, Zr and V additions for high temperature application. The characterization of the cast alloy in this study, firstly, helps to evaluate and understand its performance both chemically and structurally according to their physical state: as-cast or as-quenched. Comparison of precipitation kinetics between a binary Al-3.5%wt.Cu alloy and the AlSi7Cu3.5Mg0.1 (Mn, Zr, V) alloy has been characterized by differential scanning calorimetry, TEM observations and micro-hardness testing. The Kissinger analysis was applied to extract activation energies from non-isothermal DSC runs conducted at different stationary heating rates. The study focuses on the impact of the chemical composition such as Si content on the kinetics parameters.INTRODUCTION Pure metal Aluminum shows poor mechanical properties and its malleability is high, that is why alloying elements are added to the mixture before casting to improve physical, mechanical and thermodynamic properties (Javidani, 2015); such as Silicon (Si) for casting properties (castability, cold crack capability, wear resistance, shrinkage behavior), Magnesium (Mg) and Copper (Cu) to generate precipitation hardening systems. Aluminum hypoeutectic alloys (<12% Silicon) with Cu, Mg additions used in the automotive industry for manufacturing mechanical parts (Larouche & Javidani, 2014) are mostly subject, after casting, to precipitation hardening heat treatment (Mohamed & Samuel, 2012) according to specifications and associated standards. The best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, generally including: solutionizing, water quenching and artificial aging (Manente & Timelli, 2011). Hypoeutectic aluminum-copper alloy with amount of Cu around 1 to 4.5wt% is an elementary case for precipitation in heat treatable aluminum alloys. Researchers essentially focused their work on the full precipitation sequence of binary Al-Cu alloy during aging which is presented below."

Jan 1, 2018

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth&apos;s crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By Robert J. Uffen

YOU will likely recall the accomplishments of the International Geophysical Year of 1957, with its polar expeditions, the discovery of the Van Allen radiation belts and the spectacular launchings of the first artificial earth satellites. Our know ledge of the exterior of the earth was greatly increased by this international, friendly, cooperative scientific investigation. The Inter-national Union of Geodesy and Geo-physics has now been joined by the new International Union of Geological Sciences in sponsoring a similar study of the earth's interior. The program will extend from January, 1962 until December. 1964, and is known as the International Upper Mantle Project. During the T.G.Y studies of the interior of the earth were relatively neglected, even though the same international •Cooperation in obtaining simultaneous world-wide observations, by similar instruments, is required to locate and study earth-quakes, for example, as it is to study the earth's upper atmosphere. The upper mantle is 1•emote from man, as it extends from a depth of about 10 km. to perhaps 1000 km., but its practical importance is great.

Jan 1, 1962

By J. G. Thomson

Development of the Canadian North, a subject of growing national interest, must in part await the development of better forms of trans-port. The estimated 500,000 square miles of muskeg terrain in the north combined with the" scarcity of roads make essential the early development of special purpose muskeg vehicles. Good progress has been made in the last eleven years in classifying muskeg and some progress has been made in determining its mechanical properties. Limited travel is now possible through the use of special purpose tracked vehicles which have been built without adequate design data. A program to provide data which can be used to optimize muskeg vehicle designs began in 1957. The results of the second phase of this pro-gram are presented in this report. It is shown that vehicle performance in muskeg is directly related to the mechanical properties of the muskeg. Further, it is shown that good de-sign practice for tracked vehicles expected to operate in snow, sand, soft clays and loams is also good practice for muskeg vehicles. All indications are that muskeg mechanics is properly a part of conventional soil mechanics.

Jan 1, 1961

By C. A. D' Odorico

The zinc pressure leaching (ZPL) plant at Teck Cominco&apos;s Trail Operations was started up in 1981 and represented the world&apos;s first commercialization of the technology. From the outset, the process was designed to operate using iron-rich Sullivan Mine zinc concentrate. When the Sullivan Mine reached the end of its life in 2002, the ZPL plant underwent a significant process change with the treatment of 100% Red Dog zinc concentrate. Through careful improvements to existing plant processes, controlled changes to plant operating parameters and a rapid adjustment to the modified process by operations personnel, the plant has been successfully converted to processing a feed of 100% Red Dog zinc concentrate. This paper discusses the challenges faced during the conversion and describes the modifications to plant operating procedures, as well as changes to plant processes.

Jan 1, 2004

By Stavros A. Argyropoulos, Radhakrishna Valiveti, Bernard Closset

"The use of microprocessors in metallurgy is currently increasing at a very fast rate. A large number of companies are offering systems ""off the shelf"" which are aimed at the data acquisition and process control market. There are two main drawbacks to these systems: first, they are usually quite expensive, and second, they are not completely compatible with the target metallurgical application. An alternative is to develop a microcomputer-based system "" in lab "".A dedicated microcomputer system has proved to be very useful in many metallurgical research applications(1,2)). However, in this system the analog input signals had to be transferred over long distances , and significant noise was introduced despite the use of shielded cables. In order to overcome this problem a network of low pass-filter s was designed and built. The usage of the abovementioned system brought the need to digitize the analog signals in-situ and transfer the digital signals, which are much less susceptible to noise over very long distances. This distinctly different design philosophy has become a reality with the evolution of microprocessor technology over the last few years. This design philosophy is utilized in this development."

Jan 1, 1984