Search Documents

By J. Bouchard, A. Clapperton, L. Ebacher, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Froth flotation is used to produce nickel and copper concentrates. As is the case at other operations, the presence of magnesium is detrimental to the flotation products. In the past year, the exploitation of a new deposit has increased magnesium in the feed. Thus, it has been challenging to meet the required ratio in the final nickel concentrate. In search for a consistent solution for this problematic, an empirical flotation simulator making use of selectivity curves was developed. The circuit was expressed as a system of linear equations, which considered the distribution of copper, nickel and gangue minerals in the different streams. The relative quantities of each mineral are given by the separation efficiency curves of the various banks in the circuit. Three sources of data were used to calibrate the simulator: historical plant data (metallurgical balance), infinite dilution bench-scale flotation tests, and direct sampling of flotation cells. The calibrated separation curves were used to predict the recovery of the different species based on a single mineral recovery. Validation of the simulator showed good fit for the valuable minerals. The simulator was then used to infer the optimal operating conditions of the flotation circuit to optimise magnesium oxide content of the nickel concentrate. Simulation of two re-arrangements of the circuit gave a promising solution with a Fe:MgO ratio 2.42 times higher than the minimum value.INTRODUCTION Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Figure 1 shows the location of the mine site. After crushing and grinding, froth flotation is used to produce nickel and copper concentrates. The flotation circuit is designed with multiple stages consisting of bulk copper/nickel flotation, copper/nickel separation, and a separate nickel circuit (bulk float and cleaning)."

Jan 1, 2018

By R. Rumpold, J. Antrekowitsch

"The continued increase of the automobile production leads to a higher platinum, palladium and rhodium (PGM) demand. Due to the high value of the PGMs the recycle of these metals from automotive catalysts is of special interest. Pyrometallurgical processes, which are only focused on the PGMs, represent the state of the art of automotive catalysts recovery. However, hydrometallurgical recycling processes offer additional recovery of other valuable metals and compounds. The method presented in this paper is based on a combination of hydrochloric acid and hydrogen peroxide to dissolve the valuable metal fraction which can be precipitated afterwards.INTRODUCTIONPlatinum and the corresponding metals from the PGM group, especially palladium and rhodium are well known as catalytic active materials. They support chemical reactions which are inhibited. This effect is used to decrease the amount of harmful compounds like hydrocarbons, carbon monoxide or nitrogen oxides in automotive exhaust gases. The generation of these toxic substances is based on incomplete combustion, which in turn is caused by non-ideal conditions in the combustion chamber. Catalytic converters minimize the harmful compounds by supporting the following Reactions 1 – 3 (Votsmeier et al., 2009).CO + ½ O2 ? CO2 (1)CnHm + (n + ¼ m) O2 ? n CO2 + ½ m H2O (2)2 NO + 2 CO ? N2 + 2 CO2 (3)Platinum and palladium are very effective for the oxidation (Reactions 1 and 2), while rhodium supports the decomposition of nitrogen oxides by carbon monoxide (Votsmeier et al., 2009). The classical three way catalyst was a platinum – rhodium combination with a Pt:Rh ratio of 5:1 (Hagelüken et al., 2005). Today the platinum, palladium and rhodium ratio is highly variable and strongly depends on the engine type as well as on the car producer. Diesel engines are operated with a super stoichiometric air addition in comparison to spark ignition systems. Therefore the exhaust gas composition and off gas temperature is different. Based on the high oxygen amount, diesel engines produce less carbon monoxide and hydrocarbons but more nitrogen oxide in contrast to gasoline engines. This leads to various requirements for the catalytic converters."

Jan 1, 2012

"SART technology is a useful tool for improving the economics of gold recovery from certain types of complex gold ores. SART liberates cyanide consumed by base metals such as copper, zinc and nickel, and enables the newly freed cyanide to be recycled to precious metals leaching while producing high-grade base metal sulphide concentrates for sale. The benefits of SART include the reduction in cyanide consumption, avoidance of cyanide destruction costs, minimization of risks of environmental non-compliance due to residues of cyanide destruction reporting to mine effluents, and generation of extra revenue from the sale of base metal concentrates. Concerns with SART typically include uncertainties around capital and operating costs and proper integration of SART into the overall metallurgical flowsheet. This paper presents two case studies addressing these concerns. The first involves actual costs of the full scale SART integrated into a gold heap leach operation and treating up to 500 m3/hr of leach solution at a mine in Mexico. The second involves field pilot testing and a preliminary cost estimate for integrating SART into a silver mine in Peru using Merrill Crowe.INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes in traditional gold extraction metallurgical flowsheets. One of the tools available to the industry to help deal with interferences of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle. Although SART is a commercially available technology, it is still relatively new to the industry. Fewer than ten (10) full scale plants have been constructed in the past couple of decades. Some of these SART plants are small, most are located at remote sites, and the majority have not operated on a continuous basis. This has resulted in a general lack of information in the industry about the true costs, operability and metallurgical performance of SART. BQE Water has been involved in the design, construction, commissioning and operation of large scale SART plants in Mexico, Turkey and Chile and has conducted field testing programs as part of the technical assessment of SART integration into various metallurgical circuits. Having built and operated numerous plants utilizing selective sulphide precipitation of heavy metals, BQE Water has gained unique insight into the design and control of the sulphidization stage of SART to minimize costs and ensure high efficiency in cyanide recovery."

Jan 1, 2017

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011

By Nelson Lawrence

An Electrical Risk Management/Inspection Program has been designed specifically for the mining sector in order to provide electrical code expertise and systemic gaps in electrical systems. Goals include improved safety and productivity, reduced injuries and help to enable businesses to better comply with the electrical codes and regulations that govern them. The Electrical Risk Management/Inspection Program is now recognized by some of the world?s largest mining organizations. Since June, 2001 these electrical safety advisory services have been available to underground and surface mine sites throughout Ontario and are now offered throughout Canada and around the globe. This program is also currently being applied to review new electrical installations for mine construction projects thus improving the safety and reliability of mine site electrical systems.

May 1, 2006

By G. Danko, C. Lu

"High temperature and humidity at the working negatively affect safety and health in deep and hot underground mines. It is necessary to predict during design the dynamic changes in temperature with heat and moisture emitted into the mine ventilation-thermal-humidity (VTH) system from various sources such as auto-compression, wall of strata, mining equipment and workers. Currently available mine ventilation and climate models are either furnished with a simplified, step-change-type (SCT) model for thermal solver (such as in Climsim, VnetPC, Minevent, MFire, etc), or with more advanced models to account for the “thermal history effect” (also known as thermal flywheel effect), such as in Ventsim and MULTIFLUX. The goal is to quantify the modelling error caused by the lack of variable thermal history component in the SCT model. Two models are compared: one with and one without the thermal history component in long, single airway examples with long-term climate simulations for 20 years assuming an input air temperature with daily variation. The examples illustrate the magnitude and the time-lag phase of the variation of the modelling errors with space, time and model conditions. Large errors are shown in the order of +14°C and –7°C errors, persistent for long time periods, up to 20 days in one example.INTRODUCTIONIt is important to predict the heat and humidity distributions during the design of hot and humid underground mines for the safety and health of the workers. The feasibility of extracting a rich deposit in great depth may depend on the extent of ventilation and mine climatization for maintaining an acceptable working environment. The cost of ventilation and cooling may be substantial, up to 40–50% of the total energy cost of mining (Clausen, 2017). The accuracy of model solution is important in view of the low profit margin in mine feasibility for deep and hot mines. Safety and health of the miners, the primary concerns, are therefore inherently connected to finding ever better solutions in simulation methods and ventilation control techniques."

Jan 1, 2019

By T. Patching

"THE FOLLOWING notes on coal mining in the Edmonton city area are based, in the main, on scattered reports and accounts as little coal mining has been done in this area for about 20 years and few people are left who were involved in what was at one time an important industry of northern Alberta. Although coal mining is not likely to be permitted in the city area itself in the future, a record of this work is warranted to indicate the ·conditions and problems that may be encountered if underground mining again is proposed in the district in the same geological formations and in similar strata. Coal mining in the Edmonton area developed with the influx of settlers in the latter part of the nineteenth century and the first part of the present century. Probably local coal was used by the Fort's blacksmith as early as 1841, and the early settlers probably were 'gopherholing' into the outcrops along the river banks by the 1870s. The first report of commercial coal mining was in 1880 when a contract was let by the Hudson's Bay Company for the provision of 300 tons. As the population in the city and northern parts of the province grew, many new mines were opened along the river and in the district, and coal was even shipped by barge to points in Saskatchewan(1 ,2) By 1909 the Department of Public Works reported that 'Edmonton stands as the second largest domestic coal producing centre in the province'. It continued to hold this position until 1942. From about 1912 to 1951 annual production from mines in the city and surrounding district ranged between 0.38 and 0.65 million tons, depending on weather, wars and strikes. Production began to decline in 1951 because of the increasing availability and consumption of natural gas which was piped into the city and then provided to other towns and rural areas in the northern part of the province. Taylor noted that between 1880 and March 1970, when the last mine within the city area closed, the total of mines and prospects within the Edmonton city area rose to 153. Most of them were small; not more than 20 produced more than a quarter of a million tonnes during their entire life, and only three produced a million tonnes or more. As described by Taylor ""within the city district workings extend discontinuously from the apex of a narrow triangle near Groat Bridge to the base of the triangle in the Clover Bar area"". The larger mines were in this latter area. Approximate locations of the old mine workings in the city are shown in Taylor's atlas. A number of other coal mines were worked in the Rabbit Hill, Big Island, St. Albert, Namao, Cardiff and Morinville districts around the city."

Jan 1, 1985

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By A. Dave Mackintosh

Historical closure data has provided a description of the stress distribution patterns occurring around mine openings and enabled the development of a time ? distance plot predicting the location of the stress peak and its migration away from mine openings with time. Data collected from active mining areas during the 1970?s and 1980?s indicated the peak appeared to stabilize approximately 135m (450 ft.) from openings after four years. The region of high load and accompanying poor ground conditions in which the peak was centred was spread over approximately 45m (150 ft.) to 60m (200 ft.). Recent data from new development headings cut adjacent to 25 year old extraction areas suggests load transfer takes place over a much greater distance and time frame than predicted.

May 1, 2001

By Brian Raymond

This paper will outline the problems and solutions of the new generation washeries, as well as the recent technological advances which are being considered for future coal preparation plants. The subjects to be covered will include: - reasons for considering coal preparation plants; - raw coal crushing and handling systems; - types of coal cleaning equipment being used versus new equipment being considered; - fine coal circuit sizing; - clean coal centrifuging and dewatering; - thermal dryer problems and changes; - fine refuse dewatering systems; - clean coal storage problems and changes; - materials handling within the plants; and - control systems for preparation plants. The design and integration of the various circuits that form a modern coal preparation plant have led to the creation of an exciting new field of industrial research. As the need for energy sources increases, efficient methods of preparing coals for specific markets will become more important.

Jan 1, 1979

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

By Robert B. Parsons

"Recent amendments to the so-called ""flow-through share"" rules in our income tax legislation have given a new lease on life to this once popular investment vehicle.The original ""Dome funds"" for exploration in the Beaufort sea recognized the usefulness of flow-through share arrangements, but, by and large, flow-through shares have until recently not been able to compete effectively with other tax shelter instruments-mainly , limited partnership interests.This month, Tax Notes examines the new tax rules for investing in flow-through shares.IntroductionRecent income tax amendments have helped to rekindle investor and industry interest in so-called ""flow-through shares"" as a mechanism for mobilizing funds toward mineral exploration and development activities. In competing for investment funds, flow-through shares have historically placed a distant second in terms of investor popularity, being unable to compete with the more attractive features of limited partnership arrangements. However, primarily as a result of favourable changes to the income tax law, flow-through shares may be well poised for a comeback.This article examines the income tax considerations pertaining to issuing and investing in flow-through shares, and compares the former and the new income tax rules relating thereto. Of course, inasmuch as a flow-through share issue can involve various contractual arrangements between the investor and the issuer, there is a wide range of legal and business factors that generally have to be taken into account. A discussion of these matter s is beyond the scope of this paper, which is restricted to a summary of the special income tax factors attributable to flow-through shares."

Jan 1, 1983

By Peter N. Blakey, Jean-Paul Paquette, Barton A. Thomson

"FROM THE BEGINNING OF THE PIT, it was known that the surface mining method had a projected life of about ten years, and that the ore extended to depths recoverable only by underground mining. When serious consideration was given to underground mining in 1968, it was realized that tremendous advantages could be gained by starting the underground mine as early as• poss1ble. These included: 1. The availability of underground ore for grade control, which would become more difficult as the pit deepened. 2. The need to develop new systems, equipment and skills to take full advantage of the technological revolution in underground mining. 3. Early knowledge of rock behaviour through trial mining on a small scale prior to finalizing plans for major blocks. In addition, the pit would be available to guarantee the mill supply if problems were encountered. 4. With sufficient time and early mining experience a much better job could be done on all mine planning. Because ample reserves of economic underground ore were virtually assured, the desired underground mining capability became a function of two restraints: first, the time required to excavate and construct the permanent headframe, shaft and ore-handling facilities necessary to handle large volumes of stope ore; second, the time for lateral and stope development on at least one level which would normally follow shaft sinking. The decision made was to move immediately on the permanent hoisting installations and at the same time embark on the planned ramp from surface, which would allow much stope preparation to be completed prior to .bringing the shaft on stream. Both projects were placed on an urgent basis early in 196S' and the following decisions made shortly thereafter."

Jan 1, 1974

By Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"A Jet Diffuser Flotation Column (JDFC) is a newcomer flotation device whose operation principles similar with Jameson cell but it has an essential change in downcomer. By taking into account the hydrodynamic and fluid mechanic principles (Sahbaz et al. 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogenous dissipation of the bubbles in the separation tank. Thus the performance increase has been aimed for the coarse particles.According to theoretical results, obtained by the formula of Oteyaka (1993) showing the relationship between velocity gradient and maximum floatable size for the various contact angles, the d50 of quartz flotation of JFDC is about 240 µm and 310 µm for the contact angle of 50° and 60°, respectively. This result was verified by the experiments. According to the experimental results; d50 which was accepted the maximum floatable particle size of quartz flotation of JFDC was about 256 µm and 300 µm for the contact angle of 50° and 60°, respectively.INTRODUCTIONFlotation is a kinetic process used for separation of hydrophobic particles from hydrophilic particles. There are many different parameters affects the success of the flotation and particle size is one of them. While the flotation is very efficient for intermediate size, the efficiency of the process starts to decrease for both fine and coarse sizes (Trahar, 1981; Muganda et al., 2011). Therefore; researchers have tried to find a solution for the efficiency decrease in fine and coarse sizes by modifying the chemical condition and designing the new devices. For example, Jameson cell is a unique device for the fine particle flotation due to the suitable design and fine bubble producing (Jameson, 1988; Evans et al., 1995; Sahbaz, 2010). Because of this success operation the Jameson cell is applied more than 200 flotation plants in worldwide. On the contrary, the efficiency of the cell decreases for coarse particle flotation due to the turbulence occurred in the separation tank (Sahbaz, 2010; Cowburn et al., 2007). That’s why, new flotation device was designed in loboratory scale by Sahbaz, Oteyaka and Ucar in 2010s and it has been called as Jet Diffuser Flotation Column (JDFC) recently."

Jan 1, 2016

By M. Sakata, H. Hata, K. Haiki

"Most of the secondary ZnO contains fluorine (F) in large quantities. Serious troubles at the zinc electrowinning are occurred by the cathode corrosion caused by F, therefore we developed iron compounds as F-adsorbents used in zinc sulfate solution. The iron compounds can be reused repeatedly as F-adsorbents because they can adsorb/desorb F alternatively depending on the pH. Moreover, if the adsorptive capacity decreases, we can dissolve and re-synthesize them easily. In this paper, results of the experimental process which consists of five steps (leaching, F removal, Cl removal, purification and electrowinning) to produce high purity electrolytic zinc from the secondary ZnO are reported. INTRODUCTIONThe recycle material for zinc, secondary ZnO, contains large amounts of fluorine (F) and chlorine (Cl) which are halogen elements, compared with calcine obtained by roasting of zinc sulfide concentrate. The halogen elements cause adverse effects in the zinc electrowinning process and particularly F causes corrosion of aluminum cathode plates and eventually sticking of electrodeposited zinc and therefore, F concentration in the electrolyte is controlled to less than approximately 20 mg/L. There are several methods to remove F from secondary ZnO, such as leaching with Na2CO3 or NaOH solution [1-2], vaporizing in a rotary kiln by roasting at 1000 to 1200 degrees C [3-4]. However, up to the moment, there has been no effective method for the removal of F from zinc electrolyte and it has been a big obstacle in treatment of secondary ZnO in electrowining of zinc.The authors, therefore, developed an iron compound used as an adsorbent of F in the zinc sulfate solution [5-8]. This iron compound is Akaganeite that has a crystalline structure of ß-FeOOH. Akaganeite is synthesized by neutralization of FeCl3 solution containing a small amount of SO4 2- with Na2CO3. When this iron compound is immersed into weak acidified zinc sulfate solution, F in the solution is adsorbed. F adsorbed in the iron compound is removed by immersing in weak alkaline solution and the iron compound can be reused as F adsorbent."

Jan 1, 2012

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017