Search Documents

By P. G. Dunn, J. Fitzgerald

ABSTRACT The scheduling of underground mining activities is a complex task that must simultaneously satisfy a large number of constraints. A schedule optimization tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated through a case study. The maincomponents of the SOT include (a) a genetic algorithm that searches for optimal schedules, (b) guidance for the application of heuristic rules, and (c) sliding, which implements just-in-time development. Findings indicated that preliminary scheduling performed before invoking the SOT, intended to provide a good starting point for the search, did not ultimately lead to higher value schedules.

Jan 1, 2010

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By Ye Chen, Jianhua Chen, Xianhao Long, Qingxia Liu, Zhenghe Xu

"It is crucial to understand the mechanism of the collector interacting with the mineral surface in the presence of water molecules, which could influence the relaxation and electronic properties of sulphide mineral surface due to the proximity effect for narrow band gap of semiconductors. The adsorptions of three typical collector molecules (xanthate, dithiocarbamate and dithiophosphate) on the sulphide mineral surfaces in the absence and presence of water molecule have been simulated by density-functional theory (DFT). The calculated results show that the adsorptions of collectors on clean mineral surface in vacuum are not in agreement with the observed flotation behaviours. The presence of water molecules has a great influence on the adsorption of collectors. The analysis of density of states of the mineral surface atom suggests that the adsorption of water molecules could influence the electronic properties of mineral surface and consequently influence the adsorption between the surface and the collector molecule.INTRODUCTIONIn the separation of multi-metal sulphide ores, the selectivity of a collector is a key factor for the efficient recovery of the aimed mineral. Xanthate, dithiocarbamate (DTC) and dithiophosphate (DTP) are the most common collectors used in the flotation of sulfide minerals. Generally, xanthate exhibits powerful collecting property but lack of selectivity. While dithiophosphate and dithiocarbamate show the good selectivity in the lead and copper sulphide mineral flotation. The mechanisms of these collectors interacting with the sulphide mineral had been attracted many attentions and several mechanism based on experimental results had been reported (Chander & Fuerstenau, 1974; Fuerstenau, 1990; Raju & Forsling, 1991; Crozier, 1991; Bradshaw, Cruywagen & O’Connor, 1995; Guler, Hicyilmaz, Gokagac & Emekci, 2006). However, the micro-mechanisms of the selectivity of these three thiol collectors on different sulphide mineral surfaces are not fully understood."

Jan 1, 2016

By M. Mezbahul-Islam

Thermodynamic modeling of the Mg-Cu-Ni system is carried out as a part of multi component thermodynamic database for Mg alloys. This system is being modeled for the first time using the modified quasichemical model, which considers the presence of short range ordering in the liquid. The thermodynamic descriptions of the binaries Mg-Cu, Cu-Ni and Mg-Ni have been extrapolated to the ternary Mg-Cu-Ni system using Toop geometric model. The constructed database has been used to calculate and predict thermodynamic properties, isothermal sections and liquidus projections of the Mg¬Cu-Ni system, which showed very good consistency with the experimental data.

Jan 1, 2011

By M. G. Stamatakis, C. Zagouroglou, C. Helvaci, J. Kanaris

"Abstract -Borate minerals, such as colemanite, ulexite and borax, have been reported in Tertiary continental basins of West Anatolia, Turkey, and Samos Island, Greece.Tuffaceous rocks interbedded with the borates are rich in authigenic silicate minerals such as zeolites, potassium feldspar and opal-CT, all of which have a genetic association with the borates. Chemical analyses of the tuffaceous rocks show variation in major elements due to the varying percentage of carbonaceous, detrital, and volcanic derived material.The volcanic activity in the vicinity of each particular lacustrine basin created ion-rich fluids from which a series of borates were precipitated under arid climate. Additionally, the saline-alkaline character of these fluids was responsible for the diagenesis of the silicic glass of the tuffaceous rocks, altering them to silicates and silica polymorphs."

Jan 1, 1993

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By Y. M. Zhao, C. L. Duan, Z. F. Luo, X. L. Yang

"Fine coal beneficiation in a dry way is considerably imperative for the efficient utilization and conservation of coal resource in drought regions, especially for China. In this study, a continuous vibrated gas-fluidized bed separator was established and developed based on the results of laboratory batch separation results. The fluidization behavior and the effects of several main parameters including superficial air velocity, vibrational parameters, bed height and separating time were systematically investigated. The results showed that the bed expansion increased linearly with the superficial air velocity and theoretically, higher bed expansion benefited the hindered settling process of fine coal particles. However, larger superficial air velocity would induce intense fluctuation in bed surface and a poor performance of density segregation. The conveying velocity of particles was mainly determined by the vibration angle and a predicted model was established by the nonlinear regression analysis. A theoretical model of bed height distribution was established and this model fitted the measured value well. The beneficiation performance of this separator was evaluated by separating -3+1 mm Wuhai fine coal. The results showed that the probable error, E, is 0.225, indicating a continuous vibrated gas-fluidized bed separator could achieve a satisfactory performance.INTRODUCTIONFine coal beneficiation in a dry way is considerably imperative for the efficient utilization and conservation of coal resource in drought regions, especially for China. Meanwhile, it is also conducive to environment protect and low-carbon, green development of coal sector. In recent years, the increasing academic interest in the field of fine coal dry beneficiation has been aroused in most of big coal countries. In summary, recent processes of fine coal dry beneficiation are, according to their processing principles, mainly classified into two categories: dense medium beneficiation (Dong et al., 2015; Fan, Chen, Zhao, & Luo, 2001; Luo et al., 2008; Macpherson, Iveson, & Galvin, 2011) and improved pneumatic beneficiation (Patil & Parekh, 2011; Yang, Zhao, Luo, Song, & Chen, 2013; Yang, Zhao, Luo, Song, Duan, et al., 2013; Zhao, Zhao, Chen, & Luo, 2015). The former deploys artificial dense medium, such as magnetite powder and fine sand, to form a stable gas-solid suspension with certain density under the function of the upward fluidizing air flow and in some case, the external force field like vibration and magnetic field. Generally, it is believed that the process of air dense medium fluidized bed (ADMFB) is suitable for separation of coarse coal (-50+6 mm) and can't obtain a satisfactory result for fine coal separation (Luo, Chen, & Zhao, 2002; Luo et al., 2008). However, some recent laboratory efforts (Patil & Parekh, 2011; Zhang et al., 2014) attempt to find an improved performance for fine coal beneficiation in ADMFB with some modifications. The point of these works is to use a comparatively shallow bed and finer magnetite powder with appropriate size distribution. It is known that fluidization of finer magnetite powder is prone to arouse adverse fluidization properties such as channeling and slugging. Thus, the external force is introduced to an ADMFB in order to improve the fluidization quality of a magnetite powder bed. Some recent literature on air dense medium magnetically stabilized fluidized beds (Fan et al., 2001; Luo, Zhao, Chen, Fan, & Tao, 2002; Song, Zhao, Luo, & Tang, 2012), air dense medium vibrated fluidized beds (Luo et al., 2008) and Reflux Classifier (Macpherson, Iveson, & Galvin, 2010) reports that the separation efficiency, namely the probably error E value, of dense medium separation of fine coal ranges from 0.066 to 0.07, indicating a good separation performance. But, the main unresolved problems of dense medium beneficiation are located in the processes of product purification and medium recovery and are urgent to be solved befor"

Jan 1, 2016

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world's thickest known coal beds.

Jan 1, 1977

Agenda ?Introduction ?Geology ?Mining ?Metallurgy ?Process, Layout ?Environmental Background ?Kinross Gold Corporation owns the Lobo-Marte gold property, located in Region III of northern Chile. ?The property is close to two other Kinross mines, Maricunga 50kmto the south and La Coipa 60km to the north, plus a regional office in Copiapo and district level operating synergies are expected. ?Lobo and Marte were discovered in the early 1980s and are intrusion-hosted, porphyry-type precious metal deposits, typical of the Maricunga District. ?The Marte open pit heap leach mine was in commercial production in late 1988, but was suspended in February 1992 as it did not meet forecasted production levels and recoveries. ?Kinross plans to recover ore from the Lobo and Marte deposits through an open-pit, heap leach47,000tonne per day operation.

May 1, 2010

By D. W. Bennett, J. B. Hadaway

The operation at Phu Kham commenced design and construction in early 2006 and was commissioned in May 2008. This paper will examine and discuss the project from the inception of flow sheet development and equipment selection, equipment design and manufacture, construction, commissioning and ramp up to full production. The paper will touch on the strategies employed to achieve a short schedule and the efficient use of capital, but with the main emphasis on the grinding circuit. Various challenges during the early years of operation will be discussed including the effect of ore characteristics, including competency, on the performance of the grinding circuit. Actions to overcome these challenges and to enhance performance will also be discussed. Finally, current and future plans to improve the performance of the grinding circuit and the overall plant will be summarised.

Jan 1, 2012

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Knowing shear mechanism of discontinuities under monotonic and cyclic loading conditions is a key factor in stability analysis of rock slopes and rock foundations. In this paper, the effect of cyclic loads on the shear mechanism of joint asperities is described. For this purpose, a fresh tension-split joint from a granite block was used as a reference and thirty five mortar replicas were fabricated. Cyclic shear tests were conducted on replicas under low values of constant normal load (CNL) using a servo-controlled loading system. Tests were performed in two consecutive steps; load-controlled and then displacementcontrolled. In the load controlled part, after initial increase of shear stress to 0.25 MPa, the test was stopped for 2 minutes, then increased to 0.5 MPa, and finally decreased to 0.25 MPa. This process was repeated ten times. At the end, the test was continued up to 10 mm shear displacement under displacement-controlled loading in order to pass the peak shear strength and reach the residual strength. Characterizing joint surface and modeling of involved asperities during the tests was undertaken using a Matlab code developed with new mathematical expressions. The algorithm used in the code is based on three-dimensional coordinates of the scanned joints’ surfaces before and after the test. It was found that a high percentage of degradation happens during the first cycle of loading and during the other cycles, degradation occurs gradually. While comparing tests conducted in monotonic and cyclic loading conditions, it was observed that under low number of cycles, the pronounced mechanism is consolidation of the joint surfaces. This consolidation increases contact areas and, therefore, shear strength parameters.

Jan 1, 2015

By W. E. Bawden

Situation: Creighton mine, situated about twelve miles west of Sudbury, Ont., on the Algoma Eastern railway, is owned and operated by the International Nickel Company, incorporated in the United States under the laws of New Jersey. The ore is smelted at Copper Cliff, near Sudbury, and the matte is refined at Port Colborne, Ont., on lake Erie. Geology: The ore occurs in what is known locally as 'the basin' near Sudbury (Figure 1) the central part of which is composed of the Animikie series of sediments, consisting of sandstones, slates, tuffs and conglomerates. The basin is about 16 miles wide and 36 miles long. The Animikie sediments are surrounded by a sill of norite - a gabbro rock in which the pyroxenes are orthorombic. On the outer contact of this norite the sulphide deposits occur and the Creighton deposit, similar to others, lies on the southern edge of this basin. There are two orebodies at the Creighton, the upper one called the footwall orebôdy, and the lower one the hanging-wall orebody. The hanging-wall of both of these bodies is norite, and the footwall of the upper one is granite. The two are separated by an intrusion of greenstone which forms the footwall of the lower body. The ? maximum length of the deposit is 1000 feet and the maximum width is approximately 300 feet. It narrows at the ends and is somewhat lenticular in shape. The dip is about 45 o to the west, and the strike is north and south. The orè is a mixture of three minerals - pyrrhotite, chalcopyrite and pentlandite. The pentlandite, which is distinguished by its cleavage from the other two, is apparent to the naked eye only in the lower orebody and is more finely disseminated in the upper one. The lower body contains a little higher percentage of nickel.

Jan 1, 1925

By M. Souley, G. Armand, M. Ghoreychi, D. Seyedi, J. -B. Kazmierczak

"An anisotropic constitutive model is proposed in this paper accounting for both structural anisotropy and induced anisotropic plasticity. It is assumed that the rock is composed of a matrix and of potential planes of weakness. The matrix is assumed to be linear, transversely isotropic and the plasticity is described by a non linear yield function where the parameters are deduced from the nonlinear Hoek-Brown envelopes in pre- and post-peak, and derived from the laboratory characterization. A non-associated flow rule is used with a distinction between compression and extensional stress paths, as well as the absence of volumetric strain beyond large plastic distortion.The planes of weakness are considered as known a priori or assumed to be oriented perpendicular to the direction of the current minor principal stress. An elastic-perfectly plastic behavior according to the Mohr-Coulomb criterion is assumed in the planes of weakness; while the elastic part is considered as linear and transversely isotropic.Finally, the proposed model was implemented in FLAC3D and used to simulate triaxial compressions to provide a verification of the implementation. The applicability of the implemented model to reproduce damage (pre-peak) and/or failure developments around a circular opening is checked. The GCS drift, one of the mine-by experiments set up at the main level of the Meuse/Haute-Marne Underground Research Laboratory, is selected for this first application."

Jan 1, 2015

By G. Diaz

Técnicas Reunidas (TR) has been involved for over 30 years in the development of process technologies for the recovery of zinc from different primary and secondary feed materials, such as the ZINCEXTM process. Because of the complexity of the feed mineral resources, solvent extraction (SX) is an invaluable technique to concentrate and purify zinc solutions. When applied to a pregnant leach solution, solvent extraction can produce an extremely high quality zinc electrolyte, suitable for obtaining SHG zinc ingots, after electrowinning and melting and casting processes. However, the high affinity of most organic extractants for Fe(III) poses a serious problem, which may adversely affect the zinc extraction process. Different methods may be applied to deal with the negative effect caused by Fe(III). An acid regeneration step and electro-reduction stripping have been considered as the most viable techniques to remove the iron from the organic phase. This paper describes some findings of Técnicas Reunidas in the area of zinc solvent extraction, especially on removing Fe(III) from the organic phase.

Jan 1, 2006

By B. Damjanac, S. Maxwell, D. Chorney, M. Grob, F. Zhang, J. Hazzard

"A hybrid discrete-continuum numerical scheme is developed to study the behavior of hydraulic fractures crossing natural fractures. The fully coupled hybrid scheme utilizes a discrete element model for a core domain, within which the hydraulic fracture propagates and interacts with natural fractures, and a surrounding continuum domain to better approximate boundary effects. The results show that the behavior of hydraulic fractures crossing natural fractures is affected by a combination of factors. Nevertheless, three fundamental crossing scenarios can be identified from all of the simulations: no crossing, partial crossing, and direct crossing. Each crossing scenario has a distinct injection pressure history which may suggest guidelines for interpreting field hydraulic fracture injection data. Additionally, the capability for these models to generate synthetic microseismicity makes them appealing for the integration of microseismic field data with the reservoir geomechanics for ultimately providing a practical engineering tool for improvement of well completion and stimulation. The model is capable of examining and verifying four different shear deformation mechanisms associated with a propagating hydraulic fracture. The natural fracture can fail solely due to the stress perturbation of the passing hydraulic fracture or it can fail due to a combination of stress and pore pressure changes across different types of interaction scenarios. The simulations also illustrate that the level of fracturing complexity increases as the number and extent of the natural fractures increase. INTRODUCTIONAlthough hydraulic fracturing technique has been applied extensively as a reservoir stimulation technique in the oil and gas industry for over 60 years (Economides & Nolte, 2000), it is one of the key factors promoting the shale gas boom in the past decade (King, 2010; International Energy Agency, 2014). The hydraulic fracturing of shales can be differentiated from hydraulic fracturing of conventional reservoirs by the fact that shale formations often have a pre-existing discrete fracture networks which greatly impact the hydraulic fracture propagation. Based upon field production data as well as microseismic observations, it is believed that so called “fracture complexity” may result from interactions between a created hydraulic fracture and pre-existing natural fractures and planes of weakness (Warpinski, 2009; Maxwell & Cipolla, 2011)."

Jan 1, 2015

By Wynne Potter

"On the west coast of Cape Breton Island four coal basins have been identified, varying in age and extending from Port Hood northeasterly to Chimney Corner. Those of Chimney Corner - St. Rose in the north and Port Hood in the south belong to the Pennsylvanian Riversdale Group while lying between them are the coal basins of Mabou and Inverness belonging to the younger Pictou Group. Almost all of the coal basins are submarine and coal mining was carried out on all basins at various times. The seams in all basins dip steeply seaward at angles from 10 to 20 degrees but were found to flatten seaward. The coal is ranked as a high volatile C bituminous coal. Ash and sulphur contents are high compared with Sydney coal and the coal has a tendency to spontaneous combustion when stored in large quantities.Of the four basins, the most significant is that of Mabou. At Mabou recent seismic and drilling investigations have indicated that although a sizable reserve of coal may be found offshore the structural problems, particularly faults, and the poor quality of the coal encountered will make it a resource of the future, if at all. Inferred resources have been calculated at 150 million tonnes in four seams over a 10 km2 area and extending 3 km from shore. The quality of the Mabou coals varies with ash, ranging from 5 to 25 per cent and sulphur up to 6 per cent. Calorific value ranges from 25.3 Mj I kg to 31. 7 Mj I kg. The Port Hood and St. Rose -Chimney Corner fields (Fig. 1) contain 16 million and 3 million tonnes respectively, but the Inverness basin is considered to have been depleted. The active mine in this area is the Evans Mine at St. Rose that is currently producing between 30 -50,000 tonnes a year from proven reserves of approximately 3 million tonnes."

Jan 1, 1985

By E. Latorre, T. S. Golosinski

ABSTRACT; his paper proposes new methodology to define the pit limits that yield the maximum net present value (NPV) for a deposit, under a given economic scenario and for a given discount rate. The method uses an algorithm that combines dynamic programming and heuristics. It was tested for evaluating deposits with different sizes and various grade distributions. For the discount rate of zero, the results confirm that the economic pit limits are the same as that defined using Lerchs Grossman method. However, when discount rates higher than zero are used, the pit limits differ, yielding a higher NPV.

Jan 1, 2011

By Chuan-liu Wang

The bionic non-smooth surface has the characteristics of anti-wear, and reducing resistance. Based on bionic non-smooth surface?s characteristics, a bionic drill bit was developed. When the bionic drill bit is used, a bionic non-smooth surface forms on the crown of bionic drill bit. This surface can be used to extend the life of drill bit and improve drill efficiency. The bionic unit diameter and arrangement were researched in this paper to determine the optimal bionic non-smooth surface for further improving the life and efficiency of drill bit. Four bionic samples having the same structure size, materials and arrangement were designed and manufactured. After being sintered, the abrasion ratios of the four bionic samples were tested, and the results show that the abrasion ratio of Nos. 3 and 2 were similar (only 2% difference) and higher than that of No. 1 and 4. Therefore, the optimal diameter of bionic unit is 1.5 and 2.0 mm. Small diameter bionic drill bits were designed and manufactured, and tested in the laboratory. The results show that not all bionic structure bodies are better than normal diamond bits, except the bionic unit arranged in a reasonable range. When the angle was 24° and 30°, the arrangement of bionic unit were more reasonable, which shows the superiority of the bionic coupling bit.

Aug 1, 2013

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015