Search Documents

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By K. S. Raja, B. McNall, B. Pesic

"High-level radioactive wastes are stored in large underground storage tanks made of low-carbon steel. The wastes consist of concentrated solutions of sodium nitrate (NaNO3) and sodium hydroxide (NaOH), and the radionuclides 137Cs, 99Tc, and 90Sr. The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV), which in turn modifies the kinetics of corrosion of the storage tank. To understand the influence of technetate ions on the corrosion of steel, electrochemical polarization studies of A 537 steel samples were carried out in 1 M NaNO3 + 0 .05 M S r(NO3)2 + 0.1 M NaOH with and without addition of HReO4 at different temperatures (24 – 85 °C). The concentration of HReO4 was varied from 0.014 – 0.04 M.INTRODUCTIONAqueous processing of spent nuclear materials generates a large amount of high-level radioactive wastes. The wastes are primarily salt solutions of sodium hydroxide and sodium nitrate which also contain fission products such as 137Cs, 99Tc, and 90Sr. Among the high level radioactive fission products, Tc-99 is of great importance because of its high concentration, long half-life (2.1 x 105 years), high solubility in geologic waters as technetate, and rapid diffusivity through the geologic systems. The solubility of technetate ions varies depending on the oxidizing conditions prevailing in the storage containers. High level radioactive wastes are stored in single shell or double shell tanks made of low carbon steels such as ASTM type A15, A516-70 and A537. Most of the available literature on corrosion of steel in simulated radio active waste environments pertains to nitrate induced stress corrosion cracking (Subramanian & Mickalonis, 2005). The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV). Corrosion of steel and formation of Fe(II) and Fe(III) will affect adsorption and reduction of Tc species. The radioactive species can irreversibly be sorbed on the steel surface by oxidation of Fe(II) to more stable Fe(III) and fixed as less soluble Tc(IV)/Fe(III). The solubility of Tc species is also affected by other factors such as dissolved oxygen, local pH, temperature etc. How the corrosion behavior of steel will be affected in the presence of Tc species is not clearly understood.Cartledge (Cartledge, 1960) demonstrated that passivation of iron can be achieved in the presence of oxygen along with suitable inhibitor ions/molecules of the general formula XO4 n-, such as pertechnetate (TcO4 -). The pertechnetate ion is univalent. Since it is derived from a strong acid, no buffering action can be expected from this ion. The redox potential of the reaction (1) is 0.738 VSHE (Pourbaix, 1974)."

Jan 1, 2012

By M. M. C. Lima, L. C. S. Solimani, M. A. Quintela

Galvanized steel scrap is recycled to B OF converters where zinc escapes from the bath and is captured by the gas control system, appearing in BOF sludge. As BOF sludge contain high iron content, it could be recycled, but due to its zinc content, it is disposed in landfills. In this study techniques were evaluated for zinc layer removal from scrap by sulfuric acid leaching. The effects of coating weight, temperature, time and sulfuric acid concentration were evaluated for three different galvanized scrap. The results showed that the behavior of each galvanized scrap was different. Nevertheless zinc removal efficiency was more than 80% with low dissolved iron in the leached solution.

Jan 1, 2011

By P. D. Hodgson, G. L. Kelly, H. Beladi

"The formation of ultrafine ferrite by strain induced transformation is assessed using rolling and hot torsion experiments. These experiments are used to examine the impact of thermomechanical processing conditions and steel chemistry on strain induced austenite to ferrite transformation and the formation of ultrafine ferrite. The critical strain for dynamic strain induced transformation increased with increasing carbon equivalence, deformation temperature and austenite grain size. The deformation structure in the austenite grains changes with the thermomechanical processing conditions.Drawing on these results and the current literature, the important factors for the production of ultrafine ferrite are described and a mechanism proposed."

Jan 1, 2004

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By J. Stachulak

In recent years more emphasis has been placed on the control of nitrogen dioxide (NO2) emissions from mining diesel equipment. Worldwide, diesel engine regulations to control emission and protect the environment are also driving the development of the diesel engine technology to reduce oxides of nitrogen NOx (Nitric oxide, NO + NO2). NOx are toxic gases produced in mines during the operation of diesel equipment. Most of the diesel equipment used in underground operations are equipped with Diesel Oxidization Catalysts (DOCs) designed to reduce carbon monoxide (CO) and hydrocarbons (HC). The effects of DOCs on NO2 production from diesel powered equipment is not well understood. DOCs do not alter NOx concentration, but may promote the oxidization of engine exhaust NO to the more toxic NO2, thus increasing the undesirable NO2 exposure of workers in the mine environment. In 2012, the ACGIH reduced the NO2 TLV concentration value from 3 ppm to 0.2 ppm. Vale and CanmetMINING have been involved in several research projects to reduce diesel emissions exposure to workers. One aspect of the current program is to determine the effects of in-use DOCs on NO2 production. Several in-use DOCs taken from mining equipment were selected for testing in the laboratory using ISO 8178-C1 and mine LHD transient test cycles. The paper presents the laboratory test results and effects of DOCs on NO2 production. The results indicate significant reductions in CO concentration, by over 77%, while increases in NO2 varied from 46% to 315% based on the ISO 8178-C1 8-mode steady state test cycle. The mine LHD transient test cycle showed the same pattern, although the magnitude of CO reduction was less. Consequently, it is recommended the use of only those DOCs that have been properly evaluated and shown not to significantly increase NO2 emission in the environment be used on mine equipment.

Aug 1, 2013

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By J. Jankovic

Numerous advantages have been recognized for solid oxide fuel cells (SOFCs) operating at temperatures of 500-700°C. However, there are several issues related to low temperature SOFCs, such as high electrolyte resistance and high electrode polarization. One of the routes to enhance the electrode performance, particularly for the cathode, is to use new materials with optimized microstructure. In this work, the plasma-spraying technique, recognized to have several advantages over presently used deposition techniques, was used to deposit cathode materials onto ceramic and stainless steel substrates to obtain highly porous structures. Cathode materials with composition of Lao 6Sr0.4Co02Fe0 8O3 (LSCF) were employed in the powder form. The LSCF was prepared from powder precursors with different pore formers and binder levels, or from already produced, single-phase LSCF. The (La0.8Sr0.2)0.98MnO3 (LSM) cathode material was also processed for comparison purposes. The deposition process was developed to obtain coatings with good bond strength, porosity, film thickness and residual stresses. The phase and microstructure of deposited materials were characterized using XRD and SEM.

Jan 1, 2005

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool's dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006

By P. -Q. Wu

A modified electrochemical noise (EN) technique has been applied to monitor corrosion wear of TiN-coated ASP23 steel and TiN-coated AISI 316 stainless steel sliding against corundum in 0.5 M H2SO4. Experimental results show that the EN technique can sensitively detect potential and current variations during a corrosion-wear process. Corrosion-wear mechanisms of TiN coatings depend on their substrate properties. If the substrate is passive, such as AISI 316 stainless steel, the potential and current variations reflect the properties of the coating. Depassivation and repassivation alternately take place on the tribo-activated wear area during the steady-state phase. If the substrate is active, such as ASP23 tool steel, the electrochemical noise is dominated by dissolution of the substrate at the pinholes and the hydrogen evolution all over the exposed surface.

Jan 1, 2005

By T. Niedoba

Coal as an energetic raw material is characterized by many features that determine its quality. The data concerning coal are usually treated as independent values, despite the fact that this kind of approach is not always appropriate. In the paper the dependencies between sulfur contents and volatile components in coal and particle size and density were analyzed. The method of ordinary kriging is applied to experimental data to describe this relationship; this method can be used for particles of any size and density. An example of the application of this technique is presented for energetic coal Type 31, originating from one of the Polish hard coal mines in Upper Silesia. Results from ordinary kriging are in good agreement with experimental results. Similar analyses can be performed for other properties of coal material, such as ash content, Roga number, and moisture. On the basis of the data obtained by ordinary kriging, a more comprehensive multidimensional model is described, which can characterize certain deposits or strata from which the analyzed materials originate. This is superior to basing the model only on experimental data, which often is limited by size of the sample. The results obtained by ordinary kriging applied to various types of coal would allow more precise analysis of individual properties of the studied materials and increase the ability to determine significant differences between them. This method can be also applied to other types of mineral raw materials, such as copper ore.

Aug 1, 2013

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By F G. Cooke

"This paper describes a medium-sized copper mine's results in making innovations and changing operational practices to combat increasing expenditures due to higher labour and supply costs, extended workings, scarcity of experienced manpower and problems created by deteriorating ground conditions.OPEMISKA COPPER MINES (QUEBEC) LIMITED is located at Chapais in the Chibougamau area, in central eastern Quebec, approximately 300 miles north of Montreal and 150 miles north west of Lake St. John. The latter area, developed by lumbering and farming, has supplied the majority of the employees, who, with training and experience and a desire to work and improve themselves, have become the backbone of the Company's 600 personnel.Opemiska began production in 1954 at a rate of 400 tons per day, using diesel power and road transportation. The rate was progressively increased and, by 1959, with hydro-electric power and rail transportation, the mine had reached its present production rate of 2,000 tons per day. It has produced concentrates containing over 430 million lbs of copper."

Jan 1, 1968

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By M. Krasowska, K. Malysa, M. Krzan

The paper presents fascinating, in our opinion, observations on mechanism and course of processes occurring during bubble collision with hydrophobic and hydrophilic solid surface. Hydrophobicity of particle surface is a necessary condition for the particle attachment to bubble. We have observed that even in the case of such hydrophobic solid surface as Teflon, the bubble attachment didn't occur at first collision. In distilled water the bubble bounced a few times without attachment. Influence of a-terpineol and n¬pentanol on bubble local and terminal velocity and the phenomena occurring during bubble collisions with hydrophobic and hydrophilic solid surfaces was studied. Bubble collisions with the solid surfaces were monitored and recorded using the high-speed (1182 frames per second) camera. It was found that in distilled water the velocity variations of the "approach-bounce" cycles were identical for Teflon and glass. Four distinct "approach-bounce" cycles were detected both at Teflon and glass surfaces. Moreover, the amplitude and frequency of the velocity variations were identical on collisions with the hydrophobic (polished) and hydrophilic surface. There was no immediate three phase contact formation, with the hydrophobic Teflon surface, what we found really astonishing. Roughness of Teflon surface seems to be important parameter, which affects probability of the bubble attachment as a result of a presence of micro-and/or nano-bubbles at the surface. It was detected that the presence of the micro-bubble affected attachment of the colliding bubble even in distilled water. Presence of a small amount of a-terpineol or n-pentanol affects dramatically the bubble velocity, but their role in mechanism of the bubble attachment needs further study.

Jan 1, 2004

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By T. Marolt, J. Likar, E. Grøv, J. Žarn

"Underground structures are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, not at least nuclear facilities. When the wider area is subject to earthquake activity, underground constructions should be analyzed on seismic and static loading. Observations showed that the underground structures have significantly less seismic risk than surface structures. Available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. Simulation of earthquake loading on underground structures, in the present paper is given the various aspects of analyzing the potential damage and instability of underground facilities. INTRODUCTIONThe development of methods and computing resources used for para-seismic engineering has finetuned the evaluation of the seismic strength of buildings and equipment. Reinforcements may therefore be decided, not simply on the basis of a reassessment of the hazard, which constitutes input data for the calculation of structures and equipment, but also on the basis of developments in para-seismic engineering. Underground facilities are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, material storage, and sewage and water transport and not at least nuclear facilities. Although in the past showed that the underground structures are significantly less seismic risk than on the surface, the professional researches and their results are accessible. Seismic resistance of underground structures is analyzed from several aspects. The currently available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. For better interpretation of earthquake loading on underground structures, are given below the various aspects of analyzing the potential damage and instability of underground facilities in rock. One of the early studies which covered this are of investigation were prepared by Dowding and Rozen (1978). They grouped damages due to earthquakes in underground structures into three main categories:- damage from ground shaking- damage from fault dislocation- damage by earthquake-induced ground failures (e.g. liquefaction and landslides)."

Jan 1, 2015

By J. Stiksma, K. Buban, J. Oftsie, R. Kalanchey, S. Sadykov, E. McConaghy

The Kazakhmys zinc refinery in Balkhash, Kazakhstan, which employs the Dynatec Zinc Pressure Leach Process, officially launched autoclave operations on December 27, 2003. The Kazakhmys plant is the world's first greenfields zinc refinery based on Dynatec's two-stage pressure leach technology. Production of zinc was realized on February 9, 2004, when the first cathode was stripped. Currently the plant start-up is ongoing, with progression to two-stage zinc pressure leach operation and ramp-up to full design capacity continuing through 2004.

Jan 1, 2004