Search Documents

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By Dallas Bienhoff

Boeing Study Team Participants Andrew Daga & Associates American Aerospace Advisors Hamilton Sundstrand Harris Honeywell ILC Dover Lunar Transportation Systems Oceaneering Orion Propulsion SICSA Thin Red Line USA LSSCA BAA Topic 2: MFHE Definition Minimum Functionality Habitation Element Deployable Habitat DHE Update The Path to Growth

May 1, 2013

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By J. Paturaud, A. G. Villemiane, J. Y. Buffiere, D. Fabregue, M. Perrier

In this work, a detailed characterization of the cyclic damage mechanisms on duty in car heat exchangers has been carried out in order to improve their reliability. The material which consists in very thin (<0.3 mm thick) sheets formed of 3 co-rolled aluminum alloys (4045 /3916/ 4045) has been brazed in order to obtain metallurgical and surface conditions representative of those of the real components. Fatigue tests at constant stress amplitude have been performed at room temperature and 120°C in order i) to characterize the cyclic resistance of the studied materials and ii) to study the effect of temperature on the fatigue damage mechanism. The mechanisms leading to failure have been identified from post mortem fractographic analysis. The Wohler curves obtained show that, contrary to common structural Al alloys, this type of thin sheet brazed multi material can be cycled for several hundred thousand cycles at very high stress level (> ~ 80 % of the tensile strength). This behaviour is analysed with respect to the microstructure resulting from the brazing process and the low number of grains present in the sample thickness (around 5 grains).

Jan 1, 2015

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By B. K. Choi, S. H. Kang, G. E. Kim, K. B. Kim, S. Noh, T. K. Kim, H. J. Jin

Oxide dispersion strengthened (ODS) steel is being considered as an in-core structural material of future nuclear reactor systems because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperature in a ferritic/martensitic matrix. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. The primary activity is to develop high strength advanced ODS steel, fabrication technology for the structural components and key joining technology for the component fabrication. As a result, a Fe-10Cr-1Mo alloy with a superior creep resistance at high temperatures has been developed. An optimized fabrication process of this alloy system has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. Joining technology for the ODS steel components is also being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. These R&D activities will contribute to the realization of ODS materials for future nuclear reactor system applications.

Jan 1, 2015

By H. Salamanca

HighService has developed different equipment using wireless technology and machine vision systems that were specially designed to allow 1) the online determination of the SAG mills liner&apos;s service life, 2) the automatic detection of a missing dipper tooth in mineral extraction shovels, 3) the reduction of accident risk potential in the mineral transportation within the mine, and 4) the reduction of collision risk potential between shovels and wheel dozers during mineral extraction. For the development of all these systems at HighService, extensive research has been done in radio frequency and image processing fields. The integration of both technologies with the expert knowledge of the company on the typical harsh environment conditions of the mining industry has led to the development of heavy duty equipment that tolerate the extreme mechanical requirements of SAG mills and electrical mining shovels.

Jan 1, 2007

By Martin Bergeron

Producteur d?or de taille intermédiaire Mines Aurizon Ltée Bureau-chef àVancouverMine et projets localisés au Québec2

May 1, 2011

Arsenic bearing minerals such as enargite (Cu3AsS4) and tennantite (Cu12As4S13), which may associate with major copper minerals such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and bomite (Cu2FeS4), usually report to the copper concentrate in conventional flotation due to their similar flotation properties. Arsenic in a copper concentrate causes environmental problems and also problems in the subsequent pyrometallurgical process. Voltammetric studies were carried out to investigate the oxidation characteristics of enargite, tennantite, chalcopyrite, chalcocite and bomite. Contact angle measurements and micro-flotation tests were conducted to examine the flotation characteristics of enargite and chalcopyrite under controlled pulp potentials. Selective flotation of enargite from chalcopyrite under varied pulp potentials was conducted to investigate the feasibility of arsenic removal from a copper concentrate. The test results indicate that the non-arsenic bearing copper minerals ( chalcopyrite, chalcocite and bornite) were easier to oxidise than arsenic bearing minerals ( enargite and tennantite) in an alkaline solution. Enargite floated well at a potential as high as +0.45 V vs. SCE while chalcopyrite was completely depressed at a potential higher than +0.43 V vs. SCE. Selective flotation revealed that enargite can be successfully removed from chalcopyrite through controlling the pulp potential at +0.30 ~ +0.50 V vs. SCE.

Jan 1, 2007

By Frank Condon

?Location ?Background ?Drilling Program ?Mineral Resources ?Geology ?Economic Assessment ?Strategic Partner ?Located in Nunavik, Québec ?160 km northwest of Schefferville ?240 km south of Kuujjuaq ?160 km northeast of Brisay ?Magnetic Anomaly ?Property Boundary ?Diamond Drill Holes

May 1, 2011

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By G. G. Richards, Y. Oyediran, V. Chow

The oxygen softening process for partial removal of arsenic and antimony from lead bullion has been in use at Teck Cominco&apos;s Trail smelter since 1986. In this process, industrial oxygen is injected into bullion to remove As and Sb with the formation of an oxide slag. In Trail, the levels of these elements are reduced to concentrations suitable for processing in the Betts electrorefining plant. Recent moves toward the treatment of higher arsenic-bearing feeds have necessitated an increase in the process capacity to meet the specifications for drossing plant bullion. Process intensification trials were conducted in-plant to develop an operating strategy for higher bullion processing rates. This was preceded by a study conducted with McGill University to develop a fundamental understanding of the therm ochemistry and kinetics of the process. The results have yielded more effective control of the operation, and identified opportunities for further improvements.

Jan 1, 2008

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By Ron Zevenhoven

In Finland one opportunity for large-scale CO2 capture, utilisation and storage (CCUS) is CO2 mineralisation, i.e. mineral carbonation. A process route under development towards industrial application involves production of magnesium hydroxide or sulphate from serpentinite rock (serpentine = 3MgO·2SiO2·2H2O), followed by conversion either in a pressurised fluidised bed (PFB) reactor, giving magnesium carbonate, or in an aqueous solution process giving magnesium hydro-magnesites. Iron present in the rock is typically obtained FeO(OH). Results obtained with these process routes and progress towards industrial demonstration is addressed, process heat integration and operation on flue gases (without CO2 pre-separation!) being key features for economic viability. A process route utilizing calcium-containing slag by-product from iron- and steelmaking under development towards large-scale application is the so-called slag2pcc concept. It converts an industrial by-product into valuable material, reduces use of natural material and streams to landfills while binding CO2 produced by the process generating the slag. Using ammonium salts, calcium is extracted from steel converter (BOF) slags and subsequently carbonated in a two-stage aqueous process (at ambient temperatures and pressures). Precipitated calcium carbonate (PCC) is produced while regenerating the ammonium salt. Process performance and scale-up while guaranteeing a certain PCC quality are presented.

Jan 1, 2015

By Martha Gellner, Lutz Wuschke, Hans-Georg Jackel, Urs A. Peuker

"Electric vehicles are an alternative to the existing combustion engine driven cars. According to the EU Battery Directive a substantial recycling rate of at least 50 wt.-% has to be met for aged batteries since 2006. Existing recycling techniques are based on energy intensive pyro- and hydrometallurgical process, which are not able to recover all components. Aluminum and lithium for instance are slagged. The EU-Project “ABattReLife” investigated possibilities for a mechanical processing in order to create a sustainable process and a closed material loop from grave to cradle. After a sufficient liberation of the Li-ion batteries, components like the doped carbon black fraction (mainly lamination of electrode foils), the separator foil and the housing material can comparatively easily be separated from the other components by screening and air sifting. The remaining mixture consists of anode and cathode foils which have a similar free-settling ratio and are more difficult to separate from each other. A second comminution and compaction step modifies the particle size and shape as well as the degree of delamination. These changes influence the density of the electrode foils in order to improve the separation efficiency. Yield and purity of the generated metal concentrates were parameters to show if the separation was successful. The specific energy consumption for the different methods of processing was estimated in order to benchmark the cost-benefit ratio for each one.The studies have been accomplished with a zig zag sifter (model TUBAF), a hammer mill (model HM 340 Jehmlich) and with a Petkus-Sifter. Finally a process flow sheet was developed for a Li-ion battery recycling plant in pilot scale."

Jan 1, 2016

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By S. R. Stopic

The EU-financed INTREAT Project (Integrated treatment of industrial wastes to¬wards prevention of regional water resources contamination) addresses the environmental pollution associated with solid and liquid wastes/effluents produced by complex sulphide ore mining and metallurgical activities. The results concerning the electrolytic recovery of cop¬per from effluents formed after mixing of streams from Copper Refining, Precious Metals Plant and Electrolyte Regeneration in the Balkan Area will be shown. The waste water is characterized by low pH values and high contents of heavy metals, such as Cu, Ni, Bi, As, Sb. The majority of these waste water flow untreated into the natural water streams and through the network of existing rivers, which end up in the river Danube. The influence of current density and flow rate on the deposition rate, the quality of copper and the process efficiency will be presented. The full continuous process is based on cells with rotating disc cathodes and represents a pre-treatment step before common neutralisation in a cascade line

Jan 1, 2007

By Carlos Alberto Spier

The Águas Claras and Pico mines are two world-class, iron-ore mines hosted within Lower- Proterozoic banded iron-formations (locally known as itabirites) of the Minas Supergroup located in the Quadrilátero Ferrífero District, Minas Gerais, Brazil. The Águas Claras orebody consists of a 2,500 m long roughly tabular-shaped lens hosted within the dolomitic itabirite of the Cauê Formation. Dolomitic itabirite is the protore of the soft high-grade iron ore, which is the main ore type of the Águas Claras orebody, and represents more than 85% of the 284 Mt mined since 1973. Hematite is the main constituent of the iron ores. It occurs as martite, granular hematite and, locally, as specularite. Magnetite appears subordinately as relicts within martite and hematite crystals. Gangue minerals are very rare. These consist of dolomite, chlorite, talc and apatite and are especially common close to the contact with the protore. This virtual absence of gangue minerals is reflected in the chemistry of ores which are characterized by very high Fe contents (an average of 68.2% Fe). The Pico orebody is a continuous ~3,000 m long body of lenticular shape hosted within quartz itabirite, which is the protore of the soft high- and low-grade ores at the Pico mine. The soft high-grade ores, together with the low-grade ores, called iron-rich itabirite, are the main types of ores at the Pico mine, respectively representing approximately 51 % and 29 % of the reserves within the pit. The iron oxide mineralogy is the same as that of the Águas Claras mine, but in different proportions. Gangue minerals are very rare in the high-grade ores, but are slightly more common in the iron-rich itabirite. Quartz is the dominant gangue mineral, and is found with minor quantities of chlorite. The chemistry of the high-grade ores is characterized by high Fe contents (an average of 67.0 %) and low P, Al2O3, and SiO2 which are concentrated in the fines. Iron rich itabirites average 58.6% Fe and 13.5% SiO2.

May 1, 2003