Search Documents

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Drury SA, Williams RD, Nind DC

The Airborne Thematic Mapper is an eleven channel digital scanner which acquires image data in the visible, near infra-red, short wave infra-red and thermal infra-red wave- lengths. A description of the system is presented which includes details of the operating wavelengths and performance parameters of the scanner. Consideration is also given to the aircraft installation requirements. During January 1984 the scanner surveyed the mineral rich areas of Leonora, Laverton and Kalgoorlie in Western Australia. This is a region of intense exploration activity for gold and base metals. Some 30,000 square kilometres were systematically surveyed in a period of ten days. This scanner was flown at 7,000 metres altitude giving a ground pixel size of 17.5 by 17.5 metres. The flight line spacing was 8 kilometres. The overall project took some thirty days from conception to completion. The planning and execution of this operation are described in detail. The resulting magnetic tapes provided 11 channels of digital image data over a 30,000 square kilometre area and a variety of image processing techniques were employed in order to capitalise fully on the results. The imagery provides a powerful tool for the geological mapping of the terrain. The data can also be used to monitor the environmental effects of mining operations.

Jan 1, 1986

By J J. Hanhiniemi, M S. Powell

A ‘Variable Blend and Rates’ model is developed for SAG mills which extends upon the JKSimMet® Variable Rates Model. Similarly, a ‘Variable Blend Residence Constrained Perfect Mixing’ Ball Mill model is also introduced, also extending upon the existing JKSimMet® model. These models are used in conjunction with JKSimMet® while employing external technical programs. The technical model is then used to inform an economic model described elsewhere in Hanhiniemi and Powell (2022), which calculate operating and unit costs based on operating conditions, design, and ore characterisation. The SAG and ball mill models include constraints beyond those in the JKSimMet® models. The SAG model constraints include Size Specific Energy (SSE) verification, charge weight limit, and assessment of the impact of media to ore composition in the charge using the SAG Charge SSE Model developed in this paper. The ball mill model includes residence time, volumetric capacity, and SSE verification constraints. These models are applied to Cortez Gold Mine in the processing of two very different ore types and their blends; ‘Horse Canyon’ which is softer in coarser sizes and competent is fine sizes, and ‘Wenban’ which is competent at coarser sizes but softer in fine sizes than Horse Canyon. Horse Canyon also has a finer run-of-mine size distribution then Wenban. The application of the model at this site included undertaking five surveys at varying blends. The behaviours of the blends and individual components is then studied in the SABC circuit. A nonlinearity is observed with throughputs increasing with blending. The newly developed modelling approach captures these responses. Controlled blending based on ore competence-by-size and size distribution was implemented by the site, which then realised significant improvements in throughput without any capital cost (Ntiamoah et al, 2020). The modelling developed in this paper is then compared to existing practice, and the new method was found to provide improved fidelity and utility. A three-dimensional surface is then developed using the model describing the SAG mill throughput capacity at varying conditions (speed-filling) versus varying blend. The change in throughput as a function of only the changing charge composition is presented. The result is nonlinear, and explanations are provided to describe this behaviour.

Aug 24, 2022

Upon subduction, water is liberated from the sediments and the porous struc- ture of the oceanic crust and from de- hydration of minerals for redistribution and chemical reaction. A survey of pro- cesses which are likely to occur along the subducting plate reveals that water may well be basic in subduction induced gas generation, magma formation and ore deposition. In analogy to the industrial water gas process, reaction of water with car- bonaceous matter, in subducted sediments is likely to yield substantial volumes of hydrogen and carbon dioxide. While water and carbon dioxide appear to play a determining role in the development of differentiated magmas, hydrogen will react with metal sulfides and sulfur to form hydrogen sulfide which is essential in sulfide ore depo- sition. A survey of possible metal extrac- tion chemistry along subduction suggests a stepwise solubilization of metals from sediments and oceanic crust, and a poten tial accumulation of dissolved metals in zones of characteristic composition. The metal spectrum in ore deposits at near surface appears to reflect the com- position of the solution in the respec- tive subduction zone. A tendency for preferential solubi- lization of copper at subductidn level, from among the transition metals, an in- creasing generation of hydrogen sulfide in the sane direction and partition effects as well as sulfide precipitation characteristics lead to enrichment in copper and to its selective deposition in the direction towards the trench as observed in S. Latin America. A postscript deals with the formation of native copper.

Jan 1, 1986

By K Knorr, S Birch

The mineralogy of new certified-reference-materials (CRM) for X-ray fluorescence from Western Australia (ASCRM 030 to 035) was analysed by X-ray diffraction using the BRUKER energy dispersive one-dimensional detector LYNXEYE-XE. The samples were studied using standard-less quantitative phase analysis, based on the Rietveld method. This method delivers the relative amount of crystalline phases. All materials were found to be high-grade iron ore predominantly consisting of hematite and goethite and very low amounts of magnetite. In addition, the gangue mineralogy was characterised. It consists of low-per cent amounts of carbonate (siderite/calcite), quartz, kaolinite, chlorite and gibbsite.Furthermore, all samples were analysed with the external standard method. This is an elegant way to probe for amorphous content without adding an internal standard. All six samples were found to contain up to 16 per cent amorphous or nano-crystalline material.CITATION:Knorr, K and Birch, S, 2013. Mineralogy of new Australian x-ray fluorescence standards, in Proceedings Iron Ore 2013 , pp 269-274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Nakahiro Y, Wakamatsu T

In the present study, from experimental results, a new concept of possibility of flotation separation of quartz from feldspar is presented. The effect of the nonionic surfactant Brij 58 on the flotation behaviour of quartz and feldspar has been investigated. The effect of the surfactant adsorption at the solid-liquid interface was also studied. The results demonstrate that maximum flotability of quartz occurred at low concentration of surfactant. Feldspar is not collected by this surfactant. Flotation tests with feldspar that had previously been subjected to leaching by hydrochloric acid yielded similar flotation response as that of quartz. The effect of removal of alkali cations from feldspar surface on its flotability was investigated. The effects of inorganic and organic additives on the flotation recovery of quartz are discussed in terms of the slating-out or salting-in properties of these additives. KEYWORDS: Alkyl polyoxyethylene; feldspar; flotation; nonionic surfactant; quartz; salting-in; salting-out; separation; silanol groups.

Jan 1, 1993

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005

By C M. Stewart, P Bowen

McArthur River Mine, in the Gulf Country of the Northern Territory, exploits one of worldÆs largest deposits of zinc, lead and silver. It was officially opened in September 1995, 40 years after its discovery in 1955. This paper describes the geological, engineering and metallurgical assessments which made up the feasibility study. It then relates how these study components compare with the first two years of operation. The challenges that had to be overcome before the McArthur River Mine became economically viable included the metallurgical problems associated with extremely fine grained ore and the development of an effective mining process.

Jan 1, 1998

By M W. N Buxton, M S. Shishvan, J Benndorf

The flow of information, and consequently the decision-making along the chain of mining from exploration to beneficiation, typically occurs in a discontinuous fashion over long timespans. In addition, due to the uncertain nature of the knowledge about deposits and the inherent spatial distribution of material characteristics, actual production performance in terms of produced ore grades and quantity and extraction process efficiency often deviate from expectations. Reconciliation exercises to adjust mineral reserve models and planning assumptions are performed with timely lags of weeks, months or even years.With the development of modern information and communication technology over the last decade, a flood of data about different aspects of the production process is available in a real-time manner. For example, sensor technology enables online characterisation of geochemical, mineralogical and physical material characteristics on conveyor belts or at working faces. The ability to utilise this additional information and feed it back into reserve block models and planning assumptions opens up new opportunities to continuously control the decisions made in production planning to increase resource recovery and process efficiency. This leads to a change in paradigm from a discontinuous method to near real-time reserve reconciliation and model updating, which calls for suitable modelling and optimisation methodologies to quantify prior knowledge in the reserve model, process and integrate information from different sensor sources, back propagate the gain in information into reserve models and efficiently optimise operational decisions in real-time.This paper introduces the concept of an integrated closed-loop framework for real-time reserve management, incorporating sensor-based material characterisation, geostatistical modelling under uncertainty, modern data assimilation methods for sequential model updating and mining system simulation and optimisation. The effectiveness of the framework and the value added will be demonstrated in an illustrative case study.CITATION:Benndorf, J, Buxton, M W N and Shishvan, M S, 2014. Sensor-based real-time resource model reconciliation for improved mine production control – a conceptual framework, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 223–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By R Justa Cámara, J María Bertrán Llop

"The need for suitable geotechnical characterisation of the rock mass for underground construction is evident. The enlargement project of Railways of the Generalitat of Catalunya (FGC) in Sabadell is a patent example.In general, it is uncommon to encounter problems in the identification and characterisation of certain relevant weak rock formations, which affect project designs. However, all materials should be properly studied, as mischaracterisation can lead to a suboptimal design, resulting in construction problems during the course of the work.Good quality rock is generally not difficult to characterise, but this is not the case for Quaternary or Tertiary cemented soils. Geotechnical investigations based on boreholes do not provide enough information because samples are often badly damaged during the drilling process, if appropriate techniques are not taken. The samples can be altered and may not be representative of the in situ?material.The design and construction of the extension to the FGC line in Sabadell highlighted the importance of the characterisation of Quaternary and Tertiary cemented soils, in particular their rigidity and its underestimation. The twin tunnel project had a total length of 5.1 km, including five stations with 3.5 km excavated by tunnel boring machine (TBM). The remaining 1.6 km was constructed using cut and cover methods. The TBM portion of the tunnel had a bored diameter of 6.83 m with an internal radius of 3 m and 0.25 m thick precast concrete segments. Much of the tunnel alignment passed through and was affected by the presence of certain stiff layers of Quaternary cohesive materials.In this paper the TBM challenges faced will be discussed in detail. In particular:  TBM excavation rate reductions and overheating problems due to the required excessive thrust and torque floating problems in the lining due to nil earth pressure over the rings and the development of an improved, controlled setting time mortar to address this issue block-in and block-out methodology for each station, in some cases with internal blocks to prevent earth pressure drops and soil scouring the relevance of performing simpler solutions, for example, hyperbaric interventions to examine the cutter wheel tools when it has been shown that interventions under atmospheric conditions were equally feasible the implementation of conventional bivalve machines as standard procedure for excavation of diaphragm walls in stations, where in fact, hydrocutter machines or pile boring machines may have been required, given the mechanical characteristics of the materials to be dug out.CITATION:Justa Cámara, R and María Bertrán Llop, J, 2014. Underground extension of the FGC line in Sabadell through cemented soils, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 161–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011

By Johns AS

Comissioning of a new residue disposal tcluding upgraded classification for none backfill preparation, new variable speed pumps and a new residue dam took place in 1¦76. The system is described.

Jan 1, 1978

By D J. Gray

The 4 km long Huguenot Toll Tunnel in the Western Cape region of South Africa celebrated its tenth anniversary on 18 March 1998. At present a single (South) bore with bi-directional traffic flow is operational. The North bore was originally excavated but not lined and equipped.The tunnel is fitted with a semi-transverse ventilation system comprising 45/350 kW two speed fresh-air and 1 MW exhaust air fans at each of the portals. These provide ventilation through fresh and exhaust air ducts above the ceiling separated by movable partition doors. Secondary air ducts deliver air at low level. The fan control depends on the levels of CO pollution or visibility measured at six positions along the tunnel.The system performed well during initial tests and under conditions of low traffic volumes. As traffic volumes increased, and user complaints of bad air in the tunnel were received on several occasions, we realised that we had a problem. Tests confirmed that natural airflow within the tunnel induced by prevailing meteorological conditions outside the portals affected the performance of the ventilation system causing a plug of bad air to be trapped at varying positions along the operating tunnel.The control systems in the tunnel are presently being upgraded as described by Gray, Rieckert and Bullock (1998). As part of the retrofit we are implementing a new control strategy for the ventilation system which takes into account the external weather conditions. This paper discusses the 24 month long meteorological data gathering exercise, which is on-going, and explores the philosophies planned for controlling the ventilation system. The correlation between winds external to the tunnel and induced airflow inside the tunnel are examined. The effects of the weather induced airflow on the existing ventilation system are considered and proposals given for taking these effects into account in the new control strategy. These include the implementation of an expert system to predict ambient airflow from prevailing weather conditions, and the use of airflow measurements taken in the uncompleted North bore as a cross-check.The paper highlights the need to take cognisance of external weather conditions when designing tunnel ventilation systems.

Jan 1, 1999

The procedure used for Truck Maintenance is described systematically in this paper. Emphasis is given to manpower required, work facilities, daily maintenance and oil sampling procedure. Scheduled Preventative Maintenance Service, Electrical Service, Component Change, Truck Overhaul and Outside Contractors are also discussed. The system used, achieves the required results with an average haul truck availability in 1981 of 87.9 per cent. INTRODUCTION Situated on the Island of Bougainville, in Papua New Guinea, the Bougainville Copper mine nestles in a valley near the crest of the Crown Prince Range, between 600 m and 980 m above sea level. The mine is serviced by two towns, Arawa - an open town on the Coast and Panguna at the Mine Site. Currently Bougainville Copper operates an open pit mine removing an average of 198 000 dry metric tonnes of material per day (115 000 tonnes ore and 83 000 tonnes of waste) with a fleet of electric shovels and 154 tonne electric haul trucks.

Jan 1, 1982

By R Higashi, D Maruoka, T Murakami, Y Iwami

The ironmaking industry consumes a large amount of fossil fuel derived carbon as heat source, reducing agent of iron ores and carburising agent of reduced iron. Although the demand for drastic decrease of carbon dioxide emission, carbon is an essential element for smelting process of molten iron. The carbon recycling ironmaking process by circulating CO has been already proposed to achieve carbon neutrality. However, the production of molten hot metal is not considered in this process because sufficient amount of carbon does not dissolve in reduced iron by CO. Therefore, our group has suggested a new carbon recycling ironmaking process which can produce hot metal. In this process, free carbon and iron carbides produced by carbon deposition reaction using metallic iron as a catalyst are used. It is known that only Fe3C is obtained as iron carbide by using CO gas, however, Fe5C2 is also produced by adding H2 gas. The composite agglomerated with these carbonaceous materials and fine iron ore (Deposited Carbon-Iron oxide Composite: DCIC) is reduced and melted in a furnace. It is reported that Fe3C in DCIC accelerates the reduction reaction and melting of the composite. In this study, the effects of iron carbides and free carbon on the melting behaviour of DCIC are investigated. Fe3C, Fe5C2 and free carbon were produced by vapour deposition using porous iron whiskers and CO-CO2-H2 gas. These were agglomerated with hematite reagent at a certain ratio to prepare DCIC samples with and without Fe5C2. The samples were heated up to 1300°C in inert atmosphere. The DCIC containing Fe5C2 completely melted and iron nuggets were obtained after the experiment. This behaviour was not observed in the composite without Fe5C2. This indicates that using Fe5C2 is more preferable than Fe3C for molten iron production using DCIC.

Jun 19, 2024

Universal Resources Ltd has acquired a large portfolio of high quality exploration projects in two of Australia's most prospective regions for base and precious metal exploration: the Mt Isa Inlier (the Mt Isa-Cloncurry area) of North West Queensland, and the southern Lachlan Fold Belt in New South Wales. Drilling techniques commonly employed by the company for mineral exploration include diamond core drilling, air core drilling, reverse circulation (RC) drilling, and rotary air blast (RAB) drilling. Using examples from these two regions, each drilling technique is briefly described and compared, with particular reference to the specific advantages and disadvantages of each method for: sampling size, sample representivity, recovery, integrity and potential contamination. The applicability and implications of the different drilling techniques described for subsequent mineralogical and metallurgical evaluation work are discussed.

Mar 1, 2010

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By C Niemann-Delius

The problem of long-term open pit mine planning is a large combinatorial problem, which canÆt be solved easily by mathematical programming models because of the large problem size. In this paper a new metaheuristic algorithm, which has been developed based on the ant colony optimisation (ACO) and its efficiency, have been discussed. To apply the ACO process to a mine planning problem, a series of variables is considered for each block as the pheromone trails that represent the desirability of the block for being the deepest point of the mine in that column for the given mining period. During implementation several mine schedules are constructed in each iteration. Then the pheromone values of all blocks are reduced to a certain percentage and additionally the pheromone value of those blocks that are used in defining the constructed schedules are increased according to the quality of the generated solutions. By repeated iterations, the pheromone values of those blocks that define the shape of the optimum solution are increased, whereas those of the others have been significantly evaporated. By using this algorithm a high degree of complexities could be considered in objective function and constraints of optimisation model. In addition it can improve the value of the initial mining schedule up to 34 per cent for some cases in a reasonable computational time.

Sep 26, 2011

By H Hy÷tyniemi

In this paper multivariate data analysis performed on a new multi-camera system implemented to zinc flotation circuit of PyhSsalmi mine is presented. Image-analysis-based system was developed to take advantage of the commonly known fact that the changes in the flotation process are reflected to the visual appearance of the froth surface. Most often the changes are seen first in the froth and later in other process measurements. The image variables are already utilised in closed loop control and considerable savings are achieved with the current setting, but the results coming from the separate cells are used individually. This is clearly not the optimal way to take advantage of the many measurements coming from different locations of the process. A better approach would be for example to use the measurements coming from the early stages of the process to predict the behaviour (or improve the quality of measurements) in the later stages. The methods described in this paper are aimed to improving the situation in this sense.

Jan 1, 2005