Search Documents

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By G Pattenden, R Hargreaves, P Pettit

"Even with the cyclic nature of mining, when it comes down to it, the bottom line is that whatever direction the commodity market is going there is always a desire to improve the economics of an operation in order to deliver a greater return to investors. Adapting to market pressures by introduction of an operational process change can often have a downstream impact. What may be less obvious is that reconciliation can play an important part in measuring the effectiveness of many operational changes. Through the adoption of best practice reconciliation and related comparisons, it is possible to measure the impact of changes across the mine value chain and identify variability that may have been introduced. Using analytical business improvement tools, examining and monitoring planned changes can be crucial in understanding whether the introduced changes have been effective and whether they have provided the expected result. Using several case studies, the authors will highlight the benefits provided by modern business intelligence tools, which can provide data validation and accurately report data trends related to both planned and unplanned change events.Citation:Hargreaves, R, Pattenden, G and Pettit, P, 2016. Measuring the Effectiveness of Change through Best Practice Reconciliation, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 71–83 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L Q. Amorim

The mining district of the Quadrilátero Ferrífero (QF) in southeastern Brazil contributes to 70 per cent of the Brazilian iron ore production, which reached 370 Mt in 2010. Traditionally, four iron ore types were mined in the QF region:1. soft haematite,2. hard haematite,3. friable ‘itabirite’ (the Brazilian name for metamorphosed banded iron formation), and4. canga (an indurated iron-rich crust).With the exception of the hard haematite, these categories derive from supergene enrichment of the Paleoproterozoic Cauê Itabirite. High current iron ore demand means that the QF high grade supergene ores will be depleted in a few decades. Consequently, several mining projects are being developed to exploit unenriched, fresh itabirite. Among them, the Mineração Usiminas Serra Azul project in northwestern QF is one of the most advanced. Four major itabirite types occur in the QF region:1. siliceous (or standard),2. dolomitic,3. amphibolitic, and4. magnetitic.The dominant type in Serra Azul region is a fresh siliceous itabirite, composed essentially of haematite, martite and quartz that averages 36 per cent Fe (51.5 per cent Fe2O3) and 47 per cent SiO2. The second type, the magnetitic itabirite, consisting of magnetite, martite, gruneritecummingtonite, quartz, dolomite, stilpnomelane, and subordinate haematite, is typically a strongly magnetic greenish banded iron formation with the iron grade varying between 25 and 35 per cent. Chemically, it differs from the siliceous itabirite due to the relatively high CaO, MgO and, consequently, high LOI contents. Together with supergene ores, fresh itabirites have been included in the ore reserves of the Serra Azul project. We anticipate that all the four types of fresh itabirite will be incorporated as ore in the QF region, causing a huge increase on the iron ore resources of the district, and representing enormous environmental and technological challenges for the local iron ore industry.

Jul 11, 2011

By Smith N. S, Rholl S. A, Otterness R. E

The Bureau of Mines is conducting research to develop blast designs for the control of fragmentation and rock displacement and the reduction of overall mining costs. This Bureau experiment, a program of 25 reduced-scale blasts conducted at the University of Missouri-Rolla's experimental quarry, determined the effects on fragmentation of changes in burden, spacing, explosive diameter, and stemming-explosive length. Combined with previous work at this experimental quarry examining air gap, delay, and decoupling effects, this experiment provided a data base of over 50 shots. The fragmented rock, 1000 to 3000 kg from each 3- to 4-hole blast in the 1 m bench of massive dolomite, was completely screened to assess fragmentation. The explosive used for all the tests was extra dynamite initiated by seismic caps fired from a sequential blasting machine with delays of 5.2- to 13-ms/m of burden. Empirical equations were developed which predicted the effect of shot design parameters on the fragmentation. These formulas predicted the average fragment size of each of the 25-shots to within 13 percent. For spacing to burden ratios of 1, 1.4 and 2, there were optimum burden to explosive diameter ratios (B/de) of 30, 26 and 20, respectively. Decreasing the B/d. ratio beyond these levels resulted in little or no reduction in the average size. For B/de ratios above these levels the average size increased but, at least a 15 percent reduction in the average size results when the shot design parameters are optimized.

Jan 1, 1990

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Rare-earth permanent magnetic roll separators, pioneered by our group a few years ago, have distinctly different operation characteristics compared to prior art electromagnetic separators of various types. Many new applications for dry high-intensity (or better: high-force) magnetic separation have been developed in a short time period. It has also been found that the new generation of separators generally are more efficient with regards to removal of weakly magnetic contaminants in glass and ceramic raw materials with minimum loss of valuable product compared to induced magnetic roll (IMR) separators.The latest development is in the area of production of clean magnetic concentrates at high recoveries. It is likely that the PERMROLLR magnetic separator will replace cross-belt and lift-type magnetic separators as a result of this most recent advance.The paper will review the features of the PERMROLLR magnetic separator in comparison with other types of magnetic separators on the market and give examples on applications.

Jan 1, 1990

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C E. Woolley, A Hosseini, J Foster

Northern Star’s Thunderbox Open Pit C-Zone cutback was designed to maximise extraction in a short life excavation; In fresh rock on the western wall this included 20 m to 30 m bench heights with 6.5 m to 10 m berm widths and a 90° pre-split angle. Rock mass quality in this area is generally fair to good, however, there are sections where the dominant foliation runs parallel with the designed pit wall, and more closely spaced, altered, foliation is present: these areas are difficult to predict and prone to failure. Stringent controls and monitoring were required in order to safely access below these areas, in particular the use of slope stability monitoring radar, Trigger Action Response Plans (TARPs), re-entry procedures, visual inspections, drone inspections and day-to-day personnel awareness of the hazard. Robust and comprehensively planned remediation was also required after two significant slope failure events where long reach equipment and rope access techniques were utilised to remediate the areas in question safely, but also in a timely manner, such that expected production targets were impacted as little as reasonably practicable. This combination of rigorous risk management and well planned remediation resulted in a successful and complete extraction of the C-Zone cutback with no impact to operational safety.

Jun 22, 2022

By Y M. Lee, Y Hong, B C. Kim

Since sintered ore is the primary source for producing molten iron in the blast furnace process, maintaining stable quality despite the utilisation of low-grade iron ore is crucial. However, conventional analysis methods, such as chemical composition, ore size distribution and types of iron ore, have limitations in developing the utilisation of new low-grade iron ore and predicting sintered ore properties. Sintered ores are formed through a complex melting process of granule particles consisting of iron ore, flux and fuel. Consequently, it has been investigated that analysis methods which apply the reactive properties of iron ore to predict sintered ore characteristics. In this study, we estimated the properties of iron ore by simulating the assimilation process of coarse ore, which influences the bonding strength of sintered ores and quantifying the degree of assimilation reaction. Pseudo particles were formed by granulating coarse ore (1–3 mm) with adhering fines, which act as primary melts and sintered at 1623 K. The bonding strength of individual sintered ores, formed from 11 different types of iron ore, was measured using a simplified Tumbler Index (TI) test and each value was indexed as the Iron ore Reactivity Index (IRI). By investigating the relationship between the degree of assimilation depending on iron ore properties and the characteristics of sintered ore, we demonstrated that sintered ores formed from more reactive iron ore exhibited stronger bonding strength. Moreover, when blending conditions resulted in a higher Iron Blending ore Reactivity Index (IBRI), the physical properties of sintered ore improved. The development of this analysis method is expected to not only enable careful consideration of iron ore usability but also allow for the advance prediction of sintered ore qualities by deriving the IBRI.

Sep 18, 2023

By B Mack

The cost of water treatment is now more than ever a major consideration for maintaining an environmentally and economically sustainable mining operation. As an industry, we often have to consider water sources that are highly impure and difficult to treat. We are also discovering the value of our waste waters in this regard and using new and improved methods and technology to reclaim and reuse water. In many instances, the water or waste water to be treated is highly acidic and saturated in sparingly soluble salts. Conventional systems used to liberate this type of water typically involve high doses of lime with large volumes of waste sludge produced, and are comparatively complex to operate, to pretreat the water in order to reduce scaling tendency on the reverse osmosis stage. However, if the water is considered valuable for reuse, then why not avoid difficult and cumbersome pretreatment processes and treat the water at low pH to keep the sparingly soluble salts, metals and other dissolved species in solution. This paper describes a patented technology that uses and successfully proves this concept as a cost effective option for certain situations. Results from a treatability study on an Australian groundwater are discussed, along with an economic comparison to a conventional method and discussion on full-scale potential.

Jan 1, 2009

By B Hayes

The Ambuklao and Binga Rehabilitation Project is a 175 MW hydro power project currently under construction across dual sites in the north region of Luzon Island, Philippines. When it was built in 1956, the Ambuklao Dam harnessed the second largest hydro-electric reservoir in Asia. However, due to landslide erosion and prolonged silt infiltration caused by an earthquake in 1990, the power plant has been rendered inoperable since 1999.To bring the power generating facility back to life, the project scope entails the rehabilitation and construction of civil structures, shafts and tunnels. A major component of these works is the decommissioning of a section of the seven metre diameter headrace tunnel by installing a concrete plug. The headrace tunnel is part of a closed waterway system that connects the dam via a shaft, exhibiting a hydrostatic pressure of 13 bar (1300 kPa) at the location of the new tunnel plug. In addition, the power station ball valves have seized ajar and the damaged intake riser is unsafe toaccess thereby requiring the plugging operation to be carried out under live flowing conditions.Working under hydrostatic pressure and live conditions, the headrace plug will be an underwater tremie pour operation that includes drilling and concrete injection through blow out preventer caissons installed in the floor of an underground chamber above the tunnel. The purpose of this paper is to describe the key engineering and planning components involved in this operation including pre- and post-grouting, chamber crane, sonar, local water compensation, jet flushing, drilling, caisson installation, and concrete design, production, delivery and placement. The success of this task rests on the strategic preparation and operational management of risk and safety in a challenging rural environment.

Mar 8, 2011

By Waghorne E. P

The State Electricity Commission of Victoria is Australia's largest single coal producer. Approximately 19 Mt of coal will be produced in 1989 from the SEC V's newest mine, Loy Yang Open Cut (LYOC), which com- menced overburden stripping operation in October 1982. When the adja- cent Loy Yang Power Station is completed in the late 1990's, LYOC will supply between 35 to 45 Mt/a, depending on power station performance and demand of coal for non-power generation uses. LYOC has been a major challenge for the SECV. It is the biggest single open pit coal mining development undertaken in Australia, with a whole of life capital cost approaching A$1 billion. The mine has supplied a very rapidly growing demand for coal from the expanding power station while developing in breadth, length and depth. Coal demand has consistently been above the figures anticipated during the initial planning because of the substantially improved performance of the 500 MW units of the Loy Yang A Power Station. The superior performance of the LYOC and power station has generated additional electrical energy during the first 5 years of power station operation compared with the initial planning targets- at almost no additional capital cost. This has been a major benefit to the SECV. LYOC will continue to present major challenges for the SECV, particularly in achieving overburden removal and coal reserve targets as development of the open cut continues to full depth over the next 15 years.

Jan 1, 1989

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

By X Sun, L B. Zhou, H Yi, X Tang, P Ning

The rapid industrialisation in China has consumed large amounts of various industrial raw materials, which has left behind large quantities of industrial solid wastes produced from the processes of mining, mineral processing and smelting. The storage of huge quantities of industrial solid wastes is an obvious risk to the environment and human well-being. As the first step to fully appreciate the scale of this risk, it is necessary to carry out research for developing a pollution source environmental risk assessment system (PSERAS), especially for the typical staple industrial solid waste (TSISW). This paper aims to discuss the frame of the PSERAS for TSISW for large scale production. This system consists of two aspects: predicted factors and accidental ones, which involve physical, chemical and biological risk assessments, on-site and during transportation process. Two analysis methods, the analytic hierarchy process (AHP) and fuzzy logic assessment (FLA) were used to handle the complexity of environment and non-quantitative data. The risk assessment system for such a complex objective is difficult and the assessment of relative factors is problematic through the usual quantitative analysis. With the proposed PSERAS, it is possible to define the risk class of pollution sources. Furthermore, the risk assessment results will be helpful to the decision-maker, especially when facing unknown risks in the environmental management of industrial solid wastes. In addition, by means of the PSERAS, risk factors can be ranked against their contributions to environmental risk, in order to calculate their relative priorities in decision-making.CITATION:Sun, X, Ning, P, Tang, X, Yi, H and Zhou, L B, 2012. Environmental risk assessment system for typical staple industrial solid wastes, in Proceedings Life-of-Mine 2012 , pp 301-304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The Ernest Henry Mine is an open pit copper-gold mining operation located in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current concentrator throughput of approximately ten million tonnes per annum. The pit will cease mining towards the end of 2010. Extensive surface diamond drilling has confirmed an extension of the orebody to depths of 1000 m below surface. A prefeasibility study was commissioned in late 2006 to investigate underground mining options with the preferred mining method being an inclined sublevel cave. In February 2008 mining of a decline commenced in conjunction with a feasibility study to further investigate the project. Work from the prefeasibility study indicates that an underground crusher, conveyor and hoisting shaft could be utilised to crush and transport broken ore from the sublevel cave workings to the concentrator. The study suggests that a production rate of five million tonnes per annum could be achieved and sustained for up to ten years. Ventilation designs and requirements will form a large section of the feasibility study. This paper will detail investigations of preliminary ventilation network designs of the proposed sublevel cave. Work has been completed using both Ventsim and VumA ventilation simulation packages. Ventsim was used to provide preliminary estimations and suggest alternatives for: surface fan duties;airflow characteristics (direction, velocity, pressure and quantity); andventilation network design in key mine areas. With mining activities reaching depths in excess of 1000 m below surface an analysis of heat conditions should be conducted. The VumA software package was used to model the thermal properties of the ventilation system. This model will provide a basis for the preliminary decisions on refrigeration requirements for the mine.

Jan 1, 2008

By S Coward, S Jackson, S Moayer, J E. Vann

The variability and uncertainty of mineralisation, coupled with subsequent uncertainty in mining and processing, is often paid scant regard or overlooked during the evaluation of mining projects. In many instances, when the project transitions to the operational phase, the reality of feed or product variability and the consequences of unquantified uncertainties throughout the value chain become obvious. The outcome is the familiar picture of frequent ramp-up underperformance and failure to deliver on planned targets and objectives.Both mine and exploration geologists are expected to generate mineral deposit models that are based on an integration of diverse sources of data. These multifaceted deposit models already play a pivotal role in the design, development and optimisation of mining project value, and the trend to a fully digitally engineered future means that this importance is increasing. It is therefore vitally important that tools be made available to the geologist (as well as mining engineers and metallurgists) that enable them to characterise and assess variability and uncertainty via appropriate deposit models and thus articulate their impact on potential project configurations and decisions. Scenario-based project evaluation (SBPE) provides a framework for full and proper analysis of the downstream impacts of inherent deposit variability and uncertainty on project performance.SBPE has been developed by the authors over several years and aims to propagate geological uncertainty and variability through the mining value chain. The outcomes of SBPE can be tested against future external scenarios capturing financial, economic and socio-political factors that also drive project performance. Stochastic representations of the orebody (via conditional simulation (see Chilès and Delfiner, 1999)) that explicitly incorporate variability and represent uncertainty are propagated through the value chain on a block-by-block basis (ie on a much more granular basis than traditional project evaluation approaches).Conventionally, metallurgical processes are modelled with deterministic equations (eg regression models) based on limited data. The SBPE approach allows for the modelling of process performance uncertainty using geometallurgical sampling fully. Multiple outcomes of SBPE are passed through financial modelling, which can also incorporate stochastic components, thus allowing full quantification of the risks and opportunities of a set of project alternatives. The value of the SBPE system is that once a base case has been established, multiple engineered alternatives coupled with external scenarios are easily evaluated and compared in terms of incremental value.A new case study of SBPE is presented that shows how, by analysis of the various aspects of variability and uncertainty, project managers are able to focus on the areas that have the greatest ability to reduce risk and/or add significant value. This can lead to sufficient flexibility being built into operations that allow operators to cope with the real orebody delivered to the plant.CITATION:Jackson, S, Vann, J E, Coward, S and Moayer, S, 2014. Scenario-based project evaluation – full mineral value chain stochastic simulation to evaluate development and operational alternatives, in Proceedings Ninth International Mining Geology Conference 2014 , pp 21–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By B W. Atkinson, J Docherty

An Australian Working Group has been compiling a guide for operators to use in order to improve the efficacy of their routine and non-routine sampling tasks within their coal preparation process. The guide focuses on unit operations within the process, and not conveyor belts or transfer stations that are adequately covered by the existing Standard ISO 13909.Representative sampling of unit operations is generally an after-thought following plant construction, whether that be a result of oversight, or more commonly, capital cost minimisation during initial construction. Minimising capital cost by avoiding adequate sampling systems is generally a poor decision, since the result is a process that cannot be adequately measured, meaning that it cannot be adequately managed and optimised.The use of the term ‘guide’ rather than ‘standard’ is intentional. Practical means of sampling unit operations within existing plants generally relies on a compromise between sample representativity (minimisation of bias) and sampling feasibility. The guide does not endorse poor sampling practice, but instead offers practical guidance to overcome, to the extent reasonably possible, real-life limitations.When it comes to sampling any particular process, it is almost always necessary to make a professional judgement as to whether or not the proposed samples are likely to be sufficiently representative such that the sampling will be worthwhile. Such judgement needs to be exercised by personnel who understand the principles of sampling, as they apply to the stream being sampled. There are many circumstances where available methods for sampling of a particular stream will be meaningless, and in such circumstances analytical data from that sampling will only serve to propagate poor decision-making.This paper outlines the approach for the guide, the areas it covers and the approaches adopted for different types of unit operations and associated equipment configurations.CITATION:Atkinson, B W and Docherty, J, 2017. A practical guide to sampling in coal preparation plants, in Proceedings Eighth World Conference on Sampling and Blending , pp 241–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017