Search Documents

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

By Thomas N. Walthier

ROSPECTING for uranium in the East is hampered by the lack of bedrock exposure due to extensive overburden and residual soil. But, despite the problems of this physiographic province, it has not been ignored in the search for radioactive materials. Since 1951 both the U.S. Geological Survey and the Atomic Energy Commission have had field parties in the eastern U.S. Tempo of private prospecting is increasing, and many discoveries have resulted. AEC work so far has been concentrated in the areas of most numerous discoveries-Pennsylvania, New Jersey, and New York. Accounts of uranium mineralization in the eastern U.S. are found in the old literature and one site in the Mauch Chunk area of Pennsylvania has been known since 1874. In 1949 McKeown examined the original occurrence there and found another southeast of the town. The deposit appeared to have commercial possibilities and a short period of production began in July 1954

Jun 1, 1955

By Allen J. Johnson

Anthracite coals have been divided into three groups: (I) meta-anthracite, a high-carbon coal that is usually very slow to kindle and difficult to burn, at least on conventional equipment; (2) anthracite, a high-carbon low-volatile coal of widely accepted value as both a domestic and industrial fuel; and (3) semianthracite, a coal lying between anthracite and bituminous coal in carbon and volatile content, and also, generally speaking, in burning characteristics. Anthracite Groupings The technical differentiation between these groups, as defined by the A.S.A.-A.S.T.M. Sectional Committee on the Classification of Coals, is as shown in Table I. Tables 2 and 3 show typical analyses of anthracites and semianthracites and Figs. I to 3 show graphically the range of analytical samples. Table 4 shows the commercial sizes of coals. Meta-anthracite and Graphitic Anthracite Typical analyses from virtually every field in the United States indicate that there are few if any extensive deposits of meta-anthracite. Some of the anthracites of Rhode Island contain almost negligible quantities of volatile and would thus fall into the meta-anthracite grouping on a basis of analyses alone. However, their other characteristics indicate that it is doubtful whether they should be considered as fuels at all, but rather as graphite. In fact, this material is being mined for use as foundry facings and furnace linings.4 A typical analysis of Fenners Lodge graphite,4 from Rhode Island, is: graphitic carbon, 55.9 per cent; silica (ash), 40.6; sulphur, 1.6; moisture, 1.9; volatile, o. Other Rhode Island coals possess percentages of volatile that would throw them into the normal anthracite rather than the meta-anthracite class. However, this "volatile" is nearly all noncombustible,3,4 being composed almost entirely of carbon dioxide and inert gases, therefore its definition as volatile is open to discussion, leaving the exact classification of the fuel a moot question. One factor is certain, Rhode Island coal is so different from nor-mal anthracite in both analysis and burning characteristics that it should have a

Jan 1, 1944

By Allen J. Johnson

Anthracite coals have been divided into three groups: (I) meta-anthracite, a high-carbon coal that is usually very slow to kindle and difficult to burn, at least on conventional equipment; (2) anthracite, a high-carbon low-volatile coal of widely accepted value as both a domestic and industrial fuel; and (3) semianthracite, a coal lying between anthracite and bituminous coal in carbon and volatile content, and also, generally speaking, in burning characteristics. Anthracite Groupings The technical differentiation between these groups, as defined by the A.S.A.-A.S.T.M. Sectional Committee on the Classification of Coals, is as shown in Table I. Tables 2 and 3 show typical analyses of anthracites and semianthracites and Figs. I to 3 show graphically the range of analytical samples. Table 4 shows the commercial sizes of coals. Meta-anthracite and Graphitic Anthracite Typical analyses from virtually every field in the United States indicate that there are few if any extensive deposits of meta-anthracite. Some of the anthracites of Rhode Island contain almost negligible quantities of volatile and would thus fall into the meta-anthracite grouping on a basis of analyses alone. However, their other characteristics indicate that it is doubtful whether they should be considered as fuels at all, but rather as graphite. In fact, this material is being mined for use as foundry facings and furnace linings.4 A typical analysis of Fenners Lodge graphite,4 from Rhode Island, is: graphitic carbon, 55.9 per cent; silica (ash), 40.6; sulphur, 1.6; moisture, 1.9; volatile, o. Other Rhode Island coals possess percentages of volatile that would throw them into the normal anthracite rather than the meta-anthracite class. However, this "volatile" is nearly all noncombustible,3,4 being composed almost entirely of carbon dioxide and inert gases, therefore its definition as volatile is open to discussion, leaving the exact classification of the fuel a moot question. One factor is certain, Rhode Island coal is so different from nor-mal anthracite in both analysis and burning characteristics that it should have a

Jan 1, 1944

Members whose deaths were reported from Apr. 5, 1920, to Apr. 9, 1921. Elected Died 1916 ALLAN, FERGUS L 1920 1916 ATKINSON, CHESTER 1921 1920 BARBERENA, RAUL R 1920 1918 BARKER, F. L 1920 1914 BELL, D. A. S 1920 1920 BREWSTER, GEORGE AUGUSTUS 1920 1917 BRIGHAM, EDMUND D 1921 1915 CARROLL, D. J 1920 1897 CHAPMAN, ROBERT H 1920 1919 COOPER, W. G 1920 1918 CRITCHLOW, EDWARD B 1920 1917 CURTIS, WILLIAM L 1920 1893 DARSIE, JAMES 1920 1892 DELANO, WARREN 1920 1877 DEWEY, FREDERIC P 1921 1917 ENEBO, BENJAMIN A 1920 1896 FAWCETT, JAMES H 1920 1906 FRASER, A LEXANDER J . 1920 1889 GARLICHS, HERMAN 1921 1893 GILLET, LORENZO M 1920 1886 HALDEMAN, HORACE L 1920 1914 HALL, HARRY E 1919 1905 CHART, C. R 1920 1906 HART, PHILIP E 1920 1877 HARTRANFT, SAMUEL S 1921 1914 HICKMAN, E C 1920 1919 || INMAN, WILLIAM ELLIOTT 1921 1920 JETER, J. TINSLEY 1920 1918 JOHNSON, CHARLES W 1920 1916 JOHNSON, FRANK E 1920 1913 KING, FREDERICK G 1921 1887 KNAPP, GEORGE F 1920 1902 LAMB, RICHARD 1920 1880 LANE, J. S 1920 1920 LECKIE, WILLIAM 1920 1887 LEVAT, DAVID 1921 1882 LAWRENCE, BENJAMIN B 1918 1916 LEYNER, J GEORGE 1920 1871 LYMAN, BENJAMIN S 1920 1903 MCCHRYSTAL, JOHN H1920

Jan 1, 1923

Jan 1, 1969

Executive HOWARD N. EAVENSON, Chairman FREDERICK M. BECKET EDGAR RICKARD ERLE V. DAVELER WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL I). MERICA J. V. W. REYNDERS H. G. MOULTON, Consultant Admissions JOHN M. LOVEJOY, Chairman GEORGE D. BARRON DONALD M. LIDDELL ELI T. CONNER WILLIAM W. LYNCH Alternates WM. H. BASSETT, JR. L. B. LINDEMUTH W. A. SINSHEIMER

Jan 1, 1934

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By F. G. Smith

A few years ago, the writer encountered a problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Mathewson and Phillipsll an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-mm. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures. Preparation of Specimens The material used was cartridge brass 0.400 in. thick, having the following composition: Copper 66.60 per. cent., zinc 33.35 per cent., lead 0.02 per cent., iron 0.03 per cent. This was rolled with 35 per cent. reduction after a 700" C. anneal. Fig. 1 shows the structure of this original bar on which all subsequent anneals were made. Pieces 1 in. (2.5 cm.) wide and 3 in. long were prepared and annealed for 1/2 hr. at 450°, 550°, 650°, &apos;750°, and 850" C. Each of these pieces are indented under the Brinell test with a 10-mm. ball at 500, 1000, 2000, and 3000 kg. pressure. Then, sets of five pieces from each of the original anneals were reannealed at 450°, 550°, 650°, 750°, and 850" C.

Jan 1, 1921

By Paul D. V. Manning

MAGNESIUM is an exceedingly strategic material but the importance of its production at the time this war started was not realized. Our Government then suddenly became much alive to the need of a tremendous increase in magnesium output, and became a participator in the industry. In this paper an attempt will be made to given an over-all picture of the industry as it has been, and is being, developed. The present war is giving a great acceleration to the use of lighter metals. Development of facilities for production of great tonnages of aluminum and magnesium is bound to bring about some interesting changes in later peace times because costs will be low and production capacities high. As our knowledge of the metallurgy of magnesium alloys increases, this metal will become of vital peacetime importance and will be used in ways we do not now imagine. Household refrigerators, furniture, automobiles, even houses will all be lightened through the use of magnesium.

Jan 1, 1943

The members of the Institute living in the lower Mississippi Valley, I extend a hearty and cordial invitation to their fellow-members to meet with them nest October, in St. Louis. They believe that it will be a meeting of singular interest, inasmuch as the district in question can show in active production almost all of the more useful metals and non-metals. Perhaps too few know that the Southeast Missouri District, about 80 miles south of St,. Louis, and to which a special trip is planned, is the largest lead district in the world. It was that before-the European war, and, now that the production of lead has greatly increased abroad, and has correspondingly increased in the United States, this is one of the most interesting of all lend districts. In 1913, the production of the world was 1,270,000 tons, the last world figures obtainable. In that same year the production of the United States

Jan 5, 1917

Jan 1, 1934

By R. M. Foley, Hidesaburo Kurushima

About 25 pct of all Japanese pyrite comes from the Yanahara mine on Honchu Island. For the past 40 years lack of an economical recovery process forced the operator, Dowa Mining Co., to sell the pyrite for its contained sulfur only, leaving 7 million tons of high grade iron ore waste. Introduction of the Dorrco FluoSolids roasting system enabled the company to make use of its iron sulfides and also to find a market for the mine&apos;s considerable pyrrhotite production. The success of this project is of great importance to Japan&apos;s economy since it points the way toward material increase in her natural resources. Prior to use of the present process, no practical method was available for commercial exploitation of known large tonnages of pyrrhotite, while the copper content of the even larger deposits of pyrite made the roasted residue unacceptable for the iron and steel industry. In Europe, large amounts of copper-bearing pyrite cinder are given a chloridizing roast for separation of the copper and iron but this treatment is not economical in Japan where salt is imported from as far away as Egypt.

Jan 10, 1958

By W. A. Nagel, R. P. Alger, H. Sherman, J. Tittmann

A sidewall epithermal neutron tool has been developed to substantially reduce environmental effects that have previously complicated neutron log interpretation. Designed for operation in uncased wells, the device provides increased accuracy in both liquid-filled and empty holes. A brief discussion of neutron moderation, diffusion and capture shows that logs using epithermal neutron detection depend on a smaller number of formation-characterizing parameters than those using thermal neutron or capture gamma ray detection. Thus, they come closer to providing an unambiguorls determination of hydrogen content. In this new device a directionally sensitive epithertnal neutron detection system has been incorporated in a side-wall source-detector skid to minimize borehole effects. The effects of variations in borehole size and shape, mud type, temperature and salinity are greatly reduced. Small residual borehole effects are then computationally accounted for in the surface control panel to provide a borehole-corrected neutron log. The log presents a direct recording of neutron-derived porosity on a linear scale. With corrections for borehole effects already applied, this direct recording of porosity simplifies log interpretation. Furthermore, comparison with a linear porosity presentation of a formation density log permits sandstones, limestones and dolomites to be readily identified. Thus, in complex or variable lithology, porosity is determined with greater accuracy and reliability than heretofore. Laboratory data and field results demonstrate the improvements in neutron logging afforded by this new side-wall epithermal neutron logging device. INTRODUCTION The new Sidewall Neutron Porosity (SNP) logging system, designed for use in uncased wells, provides reliability and accuracy never before achieved with neutron logs. The effects of variations in borehole diameter and shape, fluid salinity, mud weight and temperature—parameters that have long complicated neutron log interpretation— are suppressed or corrected for by this sidewall epithermal neutron detection system. Furthermore, to simplify interpretation the SNP log presents a direct recording of computed porosity on a linear scale. The performance improvements achieved by this new system arise primarily from the combination of two im- portant design features. First. though not unique to this new tool, an epithermal neutron detection system is used,&apos;,&apos; Epithermal neutron detection substantially reduces the perturbing influences of the thermal neutron absorption properties of rock matrices and water salinity. Second, the neutron detection system is mounted in a directionally sensitive sidewall skid to greatly minimize borehole effects. The purpose of this paper is to explain briefy the advantages offered by the detection of epithermal neutrons, to describe the SNP equipment and the log, to present calibration and correction data and to give examples of interpretation methods made especially convenient by this new system. ADVANTAGES OF EPITHERMAL NEUTRON DETECTION Epithermal neutron detection, of all the neutron methods in current commercial use, provides the simplest determination of formation hydrogen content. Advantages of epithermal neutron detectors, as compared with thermal neutron and gamma ray detectors, are probably best explained by a brief review of the life of a source-emitted neutron. A fast neutron from the source will eventually be cap-tured by the nucleus of an atom. However. before capture is likely to occur, the fast neutron (energy of 100,000 electron volts (ev) or more) will be slowed down until it is in thermal equilibrium with its surroundings. The neutron is then considered to be a "thermal" neutron (average energy of 0.025 ev at 25C). The overwhelming majority of the slowing down thus occurs in reaching epithermal energies (energies just above thermal—0.5 to several ev). After reaching thermal energy. the neutron will "diffuse" through the formation with, on the average, no further energy change until capture. Upon the capture of the thermal neutron, relatively high energy gamma rays arc usually emitted. Hydrogen plays a very important role in the process of slowing down fast neutrons. On the other hand, the absorption effects of water salinity and low concentrations of other strong thermal neutron absorbers—relatively unimportant in the moderation process-—are very important in thermal diffusion, capture and the production of gamma rays. Thus, by detecting only epithermal neutrons with the SNP, spurious effects due to these thermal neutron absorbers are greatly minimized as compared to the effects on tools using thermal neutron or gamma ray detectors. The epithermal neutron detection system affords another important advantage. Log response in various litho-

Jan 1, 1967

By C. G. Brehm

THE anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal meas-ures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof sup-port and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches.

Jan 1, 1938

CONTENTS PAGE FULTON, CHARLES H., and READ, J. BURNS-A New Roasting Furnace for Zinc Flotation Concentrate. Discussed by Charles H. Fulton, Arthur S. Dwight, B. M. O&apos;Harra, Kurt Stock 1 STOCK, KURT.-Redistillation of Zinc. Discussed by G. E. Dalbey, Kurt Stock.. 3 BEASLEY, F. E.-High Zinc in Lead Blast-furnace Slags. Discussed by R. C. Canby, R. L. Lloyd, C. R. Haywood, G. E. Dalbey, A. S. Dwight, E. P. Mathewson, A. L. Walker, B. M. O&apos;Harra, and C. P. Linville 4 STEELE, E. W.-Application of Pulverized Coal to Copper Refinery Furnaces. Discussed by F. R. Pyne, E. P. Mathewson 11 LINVILLE, C. P.-Recovery of Arsenic and Other Valuable Constituents from Speiss. Discussed by C. R. Hayward, C. P. Linville, G. E. Dalbey, A. S. Dwight, Edward F. Kern, Karl Eilers, E. P. Mathewson 12 A New Roasting Furnace for Zinc Flotation Concentrate Discussion of the paper of CHARLES H. FULTON and J. BURNS READ, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1362-D, with MINING AND METALLURGY,. October, 1924. G. E. DALBEY, East Berlin, Conn. What would be the, effect on the formation of sulfates of an increased water vapor content in the roasting gases? CHARLES H. FULTON.-I cannot answer that from our experience. The question of the formation of sulfate in the roasting of zinc is mainly one of temperature and the concentration of S02 and S03 in the gases. We found we could roast almost completely to sulfate if the concentration was kept at the proper point. We, however, did not care to do this because we wished to make a 5 to 6 per cent. S02 gas for sulfuric-acid work. The sulfating of the zinc oxide in the proper concentration of gases goes on very rapidly. There are certain places in the furnace system such as the Cottrell and in a part of the dust chamber in which the roasted

Jan 6, 1925

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Aug. 10 to Sept. 10, 1914: William Huff Wagner, Milford, Del.. Stanley C.- Herold, San Jose, Cal. Charles W. Hamilton, Tampico, Mexico R. J. Grant, Denver, Colo. A. M. Van Rensselaer, New London, Conn. John Lloyd, Wilkes-Barre, Pa. . Henry C. Carr, New York, N. Y. D. M. Riordan has been appointed to act as special adviser to the Secretary of the Treasury and has sailed on the U. S. S. "Tennessee" for Europe, where he will assist in aiding Americans in returning to the United States.

Jan 10, 1914

* The greatest and richest iron ore body in the world was discovered by U. S. Steel in Venezuela in April 1947, and is disclosed for the first time in this issue (p. 178), One solid mountain of ore, Cerro Bolivar, will furnish more tonnage than the famous Hull Rust pit at Superior has, or can produce. Total resources are on the order of 2 billion tons plus. Big Steel is now moving with great speed on construction to bring out this ore, and 10 million tons are scheduled for shipment into Baltimore and Birmingham by late 1952. This ore will arrive at, Pittsburgh at a price lower than present natural ores from Superior. The Venezuelan properties will be completely mechanized. •U. S. Steel and independent companies are embarking on a taconite beneficiation program of tremendous proportions, which must be speeded to completion in the 1950&apos;s (see p. 185). By 1960 over $l.2 billion dollars will be spent on Venezuela, taconite, and Labrador to solve the United States iron ore crisis. In addition, U. S. Steel will spend another $300 million plus for a new steel mill at Trenton, N. J., before 1955. •The Deister Concentrator Co. gave $500 to the 1950 Coal Division Scholarship Fund. •Howard N. Eavenson, in analyzing the bituminous coal situation (see p. 193), suggests that anti-trust laws be extended to labor unions, disinterested trustees to administer pension funds, begin pension funds now and stop the collection of all "check-offs" for union dues or funds. •Minerals and metals worth 13.9 million dollars were produced in the United States in 1949, Secretary of the Interior Oscar L. Chapman announced. Although this value was 11 pct less than in 1948, it was the second greatest in history. Nonmetallics was the only major group that in 1949 equaled the 1948 production high. Mineral fuels decreased 12 pct and metals 15 pct. • Prospects for making gas from coal are seen to be unattractive by the Pittsburgh Consolidated Coal Co. because the success of operation depends on price and supply of coal which presently are not attractive. The company has shut down its gasification plant at Library, Pa. * Economic prospects for the immediate future in the United States are good and business probably will continue at its present high levels throughout at least the early part of 1950, Secretary of Commerce Charles Sawyer said in his year-end report to the White House based on his personal survey of business conditions. •A 467-ft well 34 miles north of Rock Springs, Southwestern Wyoming, is said to be flowing a 5 pct solution of nearly pure trona (sodium carbonate) at the rate of 10,000 barrels a day. Trona, natural soda ash, is mined for the chemical trade at Searles Lake, Calif., and from about 1500 ft underground near Green River, Wyo., and has been in short supply. •The AEC is "very much interested" in a discovery of radioactive material that has been made in Baraga County bordering Lake Superior in the Upper Peninsula of Michigan, reported F. G. Pardee, Michigan State mining engineer. The material has been identified as uranium oxide in the form of pitchblende or uraninite. The discovery, made by a geologist of the Jones & Laughlin Ore Co., is the only instance in which the commission has certified samples of Michigan rock.

Jan 2, 1950

By W. S. Gillam

A need for new supplies of fresh water exists today and in many specific areas that need is urgent. One solution lies in saline water conversion, a problem complicated by cost factors. The principles involved in saline water conversion, the status of development, and the estimated costs (present and future) of several processes are presented. Among the methods discussed are distillation, electrodialysis, and freezing. In general, the costs presented are based on a standardized procedure for estimating conversion costs, permitting a valid comparison among the various processes. The need for new supplies of fresh water and the potential benefits to be derived from an abundant supply of converted water are recognized by practically everyone concerned with water problems. The water supply problem exists today; it is urgent in many specific areas in this country and also in the world, and it will become more acute in the future. One answer to the growing problem of adequate water supplies is the development of new sources. Very significant quantities of brackish underground and surface waters exist in certain areas and an inexhaustible supply of ocean water is available. Thus in many areas water resources can be extended through saline water conversion. Congress recognized the need for new sources of fresh water in 1952 and passed the Saline Water Act, Public Law 448, amended it in 1955, and in September 1958, enacted Public Law 85-883, calling for the construction of at least five demonstration plants. The program is administered by the Dept. of Interior through the Office of Saline Water, and its primary objective is to reduce the cost of converted water produced, whether it be by development of new processes or improvement of known processes. This is a most difficult problem and one that will require several years of prodigious effort. It is difficult—not because of any intricate or new chemistry, engineering, or physics involved—but because of the difficulty in converting water at low cost. Whatever the sources of the saline water, the salts which are held tenaciously in solution must be removed before the water becomes suitable for industrial or domestic uses. Saline water is a relatively simple system of salts dissolved in water. It has certain chemical and physical properties that determine the various methods by which the salts may be separated from the water. The system, although not complex, in most instances, has had countless years in which to reach equilibrium and is, therefore, comparatively stable. Because of its stability, separation of saline solutions requires relatively large quantities of energy. The unique properties of water depend on the fact that its molecules are chemically active. The chemical and physical properties of water are associated with the type of bonding involved in the water molecule. Chemical changes such as hydrolysis, or rusting of iron, involve the breaking of chemical bonds between the hydrogen and oxygen atoms. Physical changes, such as evaporation in a boiler, the melting of ice, or the viscous resistance to flow in a pipe, involve breaking of the hydrogen bonds. (The hydrogen nucleus is so small that it can attract two negative atoms.) Thus water molecules not only combine with molecules of other compounds but even with one another; e.g., each molecule may be bounded to four other molecules. Water molecules cling to the ions of dissolved salt to form water-encumbered hydrated ions and they cling to one another to form entangling networks through which hydrated ions can be propelled only by tearing the networks apart. That is one reason why considerable energy still needs to be expended in our simplest procedures for purifying water. If water molecules did not have this habit of clinging so tenaciously to other molecules, and to one another, it would be easy to push salt ions past the water molecule and get a separation. But the water would not then dissolve salt, so the problem would not exist.&apos; Water when heated evaporates very slowly, relative to other liquids having simple molecules. Vaporization involves the separation of molecules from the liquid, and this means overcoming the attraction between molecules which is due to the hydrogen bonding. The heat of vaporization for water is high; consequently, the boiling point of water is also high. Water boils at 100" C; hydrogen sulfide (H2S) at -60" C; oxygen (02) at -183" C; nitrogen (N2) at -196" C; and methane (CH4) at-161°C, even though the latter has about the same molecular weight as water. Because of these peculiar properties of water, it exists as a liquid on earth instead of a gas such as hydrogen sulfide or nitrogen and oxygen.

Jan 1, 1961

By Alfred Brooks

Introduction PETROLEUM seepages are known in Alaska at four localities, all on Pacific seaboard. These, named from east to west, are Yakataga, Katalla on Controller Bay, Iniskin Bay on Cook Inlet, and Cold Bay on the Alaska Peninsula. Besides these, a petroleum residue has been found near Smith Bay on the north Arctic coast of the Territory. At Katalla, Cold Bay, and Iniskin Bay there has been some drilling for oil, and in the first field several productive wells have been opened up. Alaskan petroleum so far as its composition is known, is a refining oil, with paraffin base and low sulphur content. Most of what is known of the geology of Alaska oil fields is based on the investigations of Dr. George C. Martin, of the United States Geological Survey. A. G. Maddren, of the same service, has recently made a reconnaissance of the Yakataga oil field. The data to be here presented are chiefly taken from the following publications: G. C. Martin: The Petroleum Fields of the. Pacific Coast of Alaska, with an account of the Bering River coal deposits, Bulletin No. 250, U. S. Geological Survey, pp. 9 to 27 (1905). G. C. Martin: Geology and Mineral Resources of the Controller Bay Region, Alaska, Bulletin No. 335, U. S. Geological Survey, pp. 112 to 130 (1908). G. C. Martin and F. J. Katz: A Geologic Reconnaissance of the Iliamna Region, Alaska, Bulletin No. 485, U. S. Geological. Survey, pp. 126 to 130 (1912). A. G. Maddren: Mineral Deposits of the Yakataga District, Bulletin No. 592,. U. S. Geological Survey, pp. 143 to 147 (1914).

Jan 2, 1915