Search Documents

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work' the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,' Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

LIST OF MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES ALPHABETICALLY ARRANGED ||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal '23 ||Abarquez, Ramon F, Met, Bureau of Seience Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbort, A N , Mines Supt , Mazapil Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexieo '23 Abbott, Clarence E , Gen'l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H, Jr, Cons Min Engr 4812 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 Abeloff, Miran S Address Wanted '21 Abernathy, G E, Kansas State Teachers College Pittsburg, Kans '20 Abey, Hiroshi, Min & Met Engr. Takata & Co, 2 Yeirakucho, Niehome, Kolimachi-ku, Tokyo, Japan '17 ||Aborn, Robert H 24 Groveland St, Auburndale, Mass '19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cario, Egypt '17 Abraham, Arthur W 1828 N Alexandria Ave, Los Angeles, Cal '20 Abrahams, A. I 115 East 82nd St. New York, N Y '14 ||Abrahamson, C. Walter, Min Engr, Brule Min Co Stambaugh, Mich '21 Abrams, Charles Jackson Columbia Bldg, Spokane, Wash '21 Abrams, David H, Min Engr, S E Dickey & Co, 809-11 Johnstown Trust Bldg, Johnstown, Pa '20 Acker, E 01C, Met 128 East Washington Lane, Germantown, Philadelphia, Pa '86 Acker, William L, Diamond Drill Contractor Mears Bldg, Scranton, Pa '18 Ackerman, Ernest R, Pres Lawrenee Portland Cement Co Plainfield, Union Co, N J '15 Adachi, Jinzoo 11 Shiba Park, Shiba-Ku, Tokyo, Japan '88 Adachi, Yuich, Meeh Engr, Anzan Steel Works, Anzan, South Manchuria, China, (Via Dairen) '21

Jan 1, 1923

By R. E. Allen

THERE was once a time when a practical oil man would appraise or buy a producing property on the basis of from $200 to $500 per barrel of average daily settled production. Curtailment-has, for the present at least, caused a virtual abandonment of the "barrel -of settled production" as a yardstick of, oil property value and in its place has come the "barrel of allowable production," which, although an artificial thing, is nevertheless now the principal factor governing the rate of ?pay out? or investment return. The potential production of a well, settled or otherwise, is of less importance in determining the present worth of a well than is the rate at which it may be produced. Speaking only of true potential for the moment, it is obvious that of two similar wells having the same potential, the one having the highest rate of allowable production would be worth proportionately more than the one of lesser allowable. The discount factor for deferred return and risk can easily vary the present values of the two wells by as much as 20 per cent when allowable rates are not greatly different.

Jan 1, 1934

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating .tables of modern design on unclassified feeds of - 1/2 in. particle sizes, including tests on high-sulphur coals.

Jan 1, 1950

Thomas Haight Leggett, London, Eng. (communication to the Secretary): Mr. Hammond has given us a concise yet complete description of the Witwatersrand gold-fields, and the character of the operations which have resulted in their remarkable development.

Jan 1, 1902

By Samuel Taylor

IT is customary for the president of an engineering society, in his annual address, to describe either some engineering problem with which he has beer connected or to review the work of the society during his administration. My first thought, this being the sesquicentennial year of our nation, was to review the advance in coal mining for the past fifty years, during which period I have been more or less intimately con-nected with the bituminous coal industry, and have personally witnessed most of the great changes which have occurred in methods and machinery used in the production of coal, but preparation of the requisite address would take more time than could be spared to prepare it, and its presentation would consume so much time that it .would not be suitable. The new arrangement providing for giving the presi-dent's address at the business meeting makes it more .appropriate to review the work of the Institute during the past year, together with some suggestions which appeal to me as being of advantage to the future wel-fare of the Institute, which I will try to do briefly. The work of the business office has been reviewed in the Secretary's report and it will not be necessary for me to dwell on it. Suffice it to say, it seems to be going along very well. Additional work could be done which would be to the advantage of the Institute, if we had the money with which to defray the necessary ex-pense incident to it, but I will refer to this again later. I would be derelict if I did not refer to the splendid work of the Secretary and the Assistant Secretary. Keeping in touch with all the sections, which number now about 26, and affiliated student societies which number 40, besides special committees, and represent-ing the Institute on various boards, provides work enough to occupy the Secretary's time almost exclu-sively. In addition to this the Secretary and the As-sistant Secretary have the work of editing and publishing the TRANSACTIONS of the Institute; the issuing of the magazine, MINING AND METALLURGY, in the splendid manner in which it goes out to the mem-bership is no light task and I think they should receive the commendation of the membership for this work.

Jan 3, 1927

By Eugene Holman

UINQUESTIONABLY the petroleum industry not only can supply the world's present oil requirements but even can meet a considerable increase in demand if it should come. The United States produced last year 1 1/3 billion barrels of crude oil, or more than 60 per cent of the world's total. It could have provided more, if needed, because we has a large shut-in crude producing capacity. Our refining capacity of 4,500,000 0 barrels per day is more than 2 per cent above our average refinery run for 1940. Adequate crude supplies and manufacturing facilities also exist outside of the United States. Large crude reserves exist in South America, in Iran and Iraq, in Russia and Romania, in Sumatra and adjacent islands. The refineries of the Dutch West Indies, of Iran, and of the Netherland East Indies are well located in relation to crude reserves and world trade lanes. Furthermore, flexibility in the manufacturing facilities permits adjustment of yields to meet a considerable range in variations between demands for products. Only with regard to 100-octane aviation gasoline is there any apparent refinery problem. Even here so far as this country is concerned, additional refining facilities can be installed well within the time that would be required to turn out the airplane engines which will use this super fuel.

Jan 1, 1941

By Fitterer, G. R.

The impact of the work of Herty "et al" on modern liquid steel technology can only be evaluated by first setting the stage as it existed in 1926. It is important to briefly review not only the steel making process and viewpoints regarding methods of refining, but also to describe the tools which were available for research at the time. One must recall that only 15 years before the beginning of this program, the open hearth production exceeded that of the Bessemer in the United States. Many open hearths were still operating on producer gas (a very inefficient fuel), although some plants were converting to the use of natural gas and very few to oil. Continuous rolling of wide strip started this year. The Faraday Society in England held a World Conference on Physical Chemistry in Steel Making in 1925 and the contributions to this work created considerable interest throughout the world and it appeared that physical chemistry might convert the art of steel making into a science. These papers, however, attempted to solve the problems through the use of the older physical chemical concepts such as Nernst's numbers, etc. and considerable data were missing. In 1923, Lewis and Randall had published their book Thermodynanzicsl and this was later to establish and standardize the steps which are now accepted for the calculation of physico-chemical equations. At the time this research work was started, there were no small high frequency induction furnaces. Northrup had just invented his high frequency furnace and a few large units had been instilled in plants. The vacuum fusion method lor the determination of oxygen in steel was

Jan 1, 1957

By C. T. Holland

This discussion is concerned with those com-J- paratively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities." Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.' CAUSES OF ROCK BURSTS Rock bursts in coal mines have occurred in sev-eral places under diverse geological conditions, mining methods, and/or practices. A study of many such occurrences indicates that they depend on the following conditions: 1) cover thickness of 500 ft or more, 2) cover composed of strong members and having a strong member lying close to or on the coal bed, and 3) a floor that does not readily heave. The minimum thickness of cover under which coal mine rock bursts occur is based on observation. Under unusual circumstances involving very strong roof members and/or mining systems, and/or practices especially likely to induce bursts, a burst conceivably could occur under less roof. Under special circumstances rock bursts have occurred in marble quarries almost at the surface.' Furthermore, under very heavy cover it is likely that controlling roof members need not be as strong and as close to the coal bed to cause bumps. Just what constitutes a strong roof or roof member is open to question. Obviously the strength of a roof member is determined by its thickness, the distance between bedding planes across which little or no bond exists, the spacing and development of joints, and the inherent strength of the rock material. Strata sections showing roofs under which rock bursts in coal mines have developed are illustrated in Fig. 2. In several instances the strength of rocks composing the roof of mines developing bumps has been tested. The tests (Table I) show that these rocks develop considerable strength in compression, bending, and shear and that in some cases the strengths are very high. No quantitative data are available concerning joints in roof members over coal beds where rock bursts have occurred, but the author has examined many mines subject to bursts and has received the impression that joints in the shales immediately over the coal beds are always present and well developed. In the main sandstone or conglomerate members themselves, however, where observed, he has yet to see a fracture system indicating well developed joints. Undoubtedly joints are present, but the evidence indicates that they are few, poorly developed, and widely spaced. In a mine subject to bumps, moreover, actual measurements of roof spans up to 225 ft between supports under a cover of about 800 ft have been made before roof failure occurred. Such spans signify strong roof. In coal beds subject to rock bursts, the bottom rock is usually a sandy shale. A few tests (Table I) have been made on the floor rock of coal beds. Observations in mines indicate that they are usually weaker than roof rocks and that under load they show more plastic effects. Observation in ground subject to bursts invariably indicates a relatively strong floor highly resistant to heaving, although some heaving may occur. Other factors listed as favorable to rock bursts are: 1) mountainous surface; 2) steeply dipping beds; 3) proximity of faults, folds, and other similar geologic structures. Many bursts have occurred in mines under mountainous country, although many bursts in mines under a surface with little relief indicate that thickness of cover, not relief, is the essential factor. In steeply dipping beds, many bursts occur in mines that are essentially flat, and rock bursts have been recorded in beds dipping as much as 35o Most rock bursts in the U. S. occur in beds that dip less than 10 pct. It is also true that most U. S. coal is produced from beds dipping less than 10 pct. Geologically, faults are regarded as providing stress relief, but in the vicinity of faults, as well as sharp folds, it would seem that residual stresses could be present. The fact that rock bursts occur in areas remote from faults and sharp folds suggests that their presence is not necessary for this phenomenon to take place. There have been many bursts close to faults and folds, and it may be assumed that occasionally such structures accentuate their occurrence3 The conditions and circumstances under which they occur, coupled with the effects produced, leave In the Crowsnest Pass coalfield, British Columbia, a rock burst is estimated to have released 1.8 million cu ft of methane.

Jan 1, 1959

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103c1 Engineers, killed in action near Fismes, Aug. 9, 1918. Bowles, Martin F., 2d Lieut., Co. B, 355th Infantry, killed in action, Sept. 3, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on Oct. 7, 1915. Dougall, Ralph,. 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on Oct. 12, 1917. Gordy, Sheppard B., died in service, Oct. 9, 1918. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service, Jan. 1, 1918.

Jan 1, 1919

By D. Bergekoff

IN the routine examination of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of nonmetallic inclusions in both hard and soft steels, obtaining a scratch-free surface with soft metals, and avoiding the usual relief effects with very hard specimens such as tool metals con-taining various carbide and nitride phases. It is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work.

Jan 1, 1939

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral, rutile. United States consumption of titanium dioxide for these applications in 1973 was as follows: pigments, 891,000 st; titanium metal, 40,000 st (=24,000 st metal) ; and welding rod coatings, 10,000 st. The only commercially important titanium ore minerals at the present time are ilmenite, and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) states that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlines the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: "Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during the time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, Va., and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, Fla., for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for lowgrade sands, led to a return of activities in this area. The large deposits near Tahawus, N.Y., were brought into production in 1942 by National Lead Co. (now N L Industries Inc.), and by 1949 this company was the lead¬ing producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec." The beginning of the modern titanium metal industry was in 1948, when E. I. du Pont de Nemours & Co. produced the first metal. U.S. Bureau of Mines reports, which gave details of the Kroll process, together with the attractive properties of the metal for

Jan 1, 1975

By H. R. Peiffer

Recently artin has indicated that the recovery of resistivity at 145°C following elongation of molybdenum at room temperature was the result of the annihilation of vacancies. The activation energy for this process was, according to Martin, 1.26 ev. This energy seems to be a reasonable one for the activation energy for the diffusion of vacancies in molybdenum. However, impurity atoms such as carbon, nitrogen, and oxygen4 have an activation energy for diffusion in molybdenum of the same order of magnitude (i.e., 1.45, 1.15, and 2.09 ev, respectively). Cottrell and Churchman have already correlated the return of impurity atoms to dislocations in cold-worked iron with the return of the upper and lower yield point. According to cottrel16 the diffusion of carbon atoms to dislocations results in the return of the yield point. As the carbon atoms become trapped by dislocations, Bhatia has shown that a decrease in the electrical resistivity is to be expected. Cottrell and Churchman were able to correlate experimentally the decrease in electrical resistivity with the return of the yield point. Since one would expect strain aging to occur in molybdenum, an experiment was performed to determine whether the resistivity recovery at 150°C for molybdenum cold-worked at room temperature can be correlated with the return of an upper and lower yield point. For this experiment 3/16-in. tensile bars of Climax molybdenum, 99.961 pct pure, were used. The specimens were annealed at 1000° C for 1 hr in an argon atmosphere and then were elongated up to 10 pct on a Baldwin-Lima-Hamilton FGT

Jan 1, 1959

By T. Sterry Hunt

It is now five years since I called the attention of the Institute to the industrial importance of the coal and the iron ores of the Hocking Valley in Southeastern Ohio, and in a pamphlet on the region published soon after, in 1874, endeavored to resume the principal facts then known respecting it, including the observations of the geological survey of Ohio, made and published up to the time by Professors Andrews and Wormley, together with an estimate of the probable future of the region, and its relations to the coal and iron markets of the country. Since that time the labors of the Geological Survey have included a further study of the coal by Prof. Edward Orton, the results of which will be awaited with much interest. I may say from my knowledge of them, that while confirming the general conclusions of his predecessors, he has been enabled to add much to our knowledge as regards the correlation of the various members in different parts of the coal-field; and to show more clearly the positions and the importance of the ore-beds in the Hocking Valley region. The only ore mined in that vicinity previous to 1874, was below what is called the Great Vein or No. VI coal, and to the west of what is known as the Hocking Valley coal-field, and although experiments in a few furnaces in the State had shown that this coal could be used with advantage in iron-smelting there was not a single blast furnace within the field. My observations at that time, however, impressed me with the abundance of iron ore, not only below but above this important coal seam, and I then ventured to express the opinion that this region, from its cheap and easily mined smelting-coal, its native ores and limestones, and its geographical position and relations to the great markets of the West, and to the supply of rich iron-ores from Lake Superior, was destined at no distant time to become a great metallurgical centre, where iron could be made more cheaply than at any other equally accessible point in the country. The object of the present communication is to report progress, and to state how far my observations made in the region 1st month have justified the predictions of 1874. The five years which have elapsed have been, as all know, most unfavorable to the iron trade, and especially to new enterprises in untried regions, yet they have not passed without important industrial developments in the Hocking Valley, where not less than thirteen blast furnaces have been erected

Jan 1, 1879

In the Bowen Basin of central Queensland, coal production has gone from virtually nothing in 1961 to more than 24 million tons today4ut there's a cloud over this success.

Jan 1, 1977

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of March, 1913 BAECHTOLD, CHARLES A., Engr 9G Liberty St., New York, N. Y. BRANTLY, JOHN E., Instructor in Geology Tuscaloosa, Ala. CADDY, JAMES P., Net., ,Lake View & Star, Ltd Fimiston, West. Australia. LONERGAN, PHILIP J., JR., Prof. of Mining, Government University, Peking, China. MCKANNA, EDWIN A., Min. Engr P. 0. Box 834, Oklahoma City, Okla. MACDONALD, ANGUS W., Supt. Labor Dept., Dominion Coal Co., Ltd., 21 Queen St., Sydney, N. S., Canada. TSUBOI, Yoshio, Min. and Met. Engr., Kosaka Mine, Fujita Co., Akita-ken, Japan.

Jan 4, 1913

By AIME AIME

SILVER reached a new high, with the ceiling the limit, at the annual Institute dinner at the Commodore on Washington's Birthday night. Carrying along as ballast other commodities, such as rolls, roses and ferns, souvenir boxes and table number placards, hundreds of silvery balloons, cut loose from their moorings at the tables, bounced idly against the plaster decorations high overhead. At the head table, Scott Turner, retiring President, pre- sided as toastmaster, with the new President, Frederick M. Becket, on his right, and the Chairman of the New York Section, Sydney H. Ball, on his left. Many other distinguished Institute members, medalists, and representatives of organizations and committees, ranged to the east and west. Each had the opportunity at least to rise and bow.

Jan 1, 1933

By J. E. Howard

On Aug. 25, 1911, a rail failed on the Lehigh Valley Railroad, causing a disastrous wreck. The surface of the fracture was in a plane at right angles to the length of the rail. There was a dark-colored, oval spot on this surface, located on the gage side of the head, representing the part of the rail which was the first to fracture. The nucleus of this spot showed that the fracture had an interior origin. Other fractures of this kind, the peripheries of which had not reached the surface of the rail, presented surfaces having a (silvery luster. The darkened surface of the present fracture was caused, doubtless, by the air having had access to it. This fracture was recognized as a fatigue fracture, of a modified type, its interior origin having been due to a component in the rail which is not usually present in cases of fatigue fractures. The metal next the running surface of the head of the rail was in a state of internal compression, this being the component not commonly met with in other cases, and which caused the fracture to have its interior origin. For the purpose of giving this modified type of fatigue fracture a specific name, for identification, the term "transverse fissure" was applied. No mystery was thought to attach to its formation, or to its development. The explanation of its occurrence seemed obvious in the light of common knowledge upon the behavior of steel under repeated alternate stresses.' By reason of the state of internal compression at the running surface, the maximum tensile stresses in the head, ander bending loads, were along an interior element. Here the tensile strains were higher than in the fibers more remote from the neutral axis. Under such conditions the fracture of the rail would be expected to have an interior origin. A discussion of the subject of transverse fissures essentially becomes a discussion of fatigue fractures, since they are believed to be identical. The descriptive term employed, merely for the identification of this type of fatigue fracture, had the appearance of creating alarm. Apprehensions arose that a new phenomenon in the physical properties of steel had presented itself, the explanation of which was sought in every

Jan 1, 1918

By W. R. Hibbard

IN ref. 1, on the basis of tension and torsion experiments with single crystals of a brass, the values given in Table I were obtained for elastic coefficients. It was pointed out by Zener that the values for the 71.2 pct Cu were not satisfactory, since they resulted in a negative value for the bulk modulus, namely —4.17X1012 sq cm per dyne. In reevaluating the data of this investigation, it was determined that the reason for this negative bulk modulus lay in the extrapolation of the reciprocal Young's modulus to the zero value of the orientation function shown in Fig. 5 of ref. 1. This extrapolation was reevaluated by the method of least squares (50 pct probability) and a new value of the coefficient S,, was determined as 18.9220.42X 10M sq cm per dyne in lieu of the value originally reported of 18.82x10 sq cm per dyne. This new value of S, leads to a new value of S, of — 9.43 X101" sq cm per dyne. The values of the other coefficients are unchanged. results. This value compares with the value of 12.3X10 sq cm per dyne reported by Schmid and Boas? The new results are summarized in Table 11. These results follow similar qualitative trends, previously published,' relative to the effect of zinc content. However, the derived values of C11, C,, C,, and K are so sensitive to the uncertainty in the first decimal place of the S, values that they are probably not useful. This uncertainty must also apply to the previous results of Masima and Sachs," who obtained S, values from a similar extrapolation drawn wholly above their data points. Acknowledgments Advice and assistance on the statistical methods were obtained from R. W. Guard. The calculations were carried out by Miss E. Saacke.

Jan 1, 1958