Search Documents

By R. L. Marek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalitics coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance. [ ]

Jan 1, 1930

Organization Place Date 1917 American Electrochemical Society Pittsburgh, Pa. Oct. 3-6 American Institute of Mining Engineers St. Louis, MO. Oct. 8-13 American Gas Institute : Washington, D. C. Oct. 16-19 American Institute of Architects Philadelphia, Pa. _ Dec.. 26-29 American Society of Mechanical Engineers New York City. Dec. 26-29 American Mining. Congress State Chapter Phoenix, Ariz. Dec. 26-29

Jan 10, 1917

By Manqiu Xu, Joe Holmes, Peter Wells, Peter Langlois, Germain Labonté, Jim Barrett

"The flowsheet for the Voisey’s Bay mill had to meet the challenge of processing an ore containing high pentlandite and chalcopyrite values in a largely pyrrhotite/troilite matrix. In the 1994-97 period, circuit development focused on making a high-grade copper concentrate and a relatively low-grade nickel concentrate. However, in 1998 a circuit with copper concentrate, high-grade nickel concentrate and a Ni/Cu middlings concentrate was specified. Following a three year project delay, work resumed on the flowsheet in 2001, and the target for the overall grade of the nickel concentrate was raised from 14% to 20% nickel. To achieve this target triethylamine tetramine (TETA) and sulfite pyrrhotite depressants were used in an all lime circuit. It later became evident that, with appropriate selection of collector and adjustment of the circuit by the addition of a scavenger on the scavenger cleaner, it would be possible to approach the grade of concentrate required without the use of pyrrhotite depressants. The recycle of water and the contained thiosalts was also proven to be instrumental in raising the grade.Construction and commissioning of the mill were fast-tracked with start-up of the mill in September 2005 some six months ahead of the original schedule. Ramp-up of both throughput and metallurgy was faster than any other recent nickel installations with tonnage being limited mainly by concentrate dewatering due to the higher than initially planned ore grades.INTRODUCTIONNickel was discovered in the vicinity of Voisey’s Bay by Chislett and Verbiski working for Diamond Field Resources in 1993 and the Ovoid deposit was delineated in the winter of 1994/95. By the end of 1995 the Ovoid had been well explored and at that time was thought to have a reserve of at least 30 million tonnes with an average grade of 2.83% Ni and 2.0% Cu. Drilling to the east of the Ovoid had indicated the presence of significant mineralization. In June of 1995, Inco Limited bought a 25% share in the Voisey’s Bay Nickel Company (VBNC) which was a subsidiary holding company set up by Diamond Fields. Inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBNC for twenty years as part of this agreement. In April 1996, Inco bought the 75% of VBNC shares that it did not own."

Jan 1, 2007

By H. Reimer

The rates of return on investment are examined for several major Canadian mining companies. Because we are dealing with a highly cyclical industry, subjected to widely fluctuating metal prices, rates of return are examined over a 20-year period. Conveniently, the first decade examined reflects the period when the industry enjoyed incentives to develop deposits; during the second decade, incentives were reduced and the industry became the most heavily taxed industry in Canada. The high rates of inflation since 1973 have distorted the real rates of return on investment if one considers replacement cost.

Jan 1, 1977

By Shahé Shnorhokian

A study was conducted on the seismic activities and associated rockburst events that took place at an underground Canadian metal mine over a period of five years. In the first stage, a back analysis of the microseismic database led to the identification of clusters of major events. The locations of these clusters were identified with respect to the local geology and the planned mining sequence. In the second stage, a numerical model was constructed using the finite difference code FLAC3D to simulate the in-situ stress, mine geometry, local geology, and stope sequence. Mining-induced stress fields were compared against two rockburst events that took place during this period, as well as against the various geologic units present. It was shown that by combining microseismic analysis and numerical modeling, it was possible to provide a basis for evaluating the influence of the in-situ stress regimes and stope sequencing on mining-induced seismic response.

May 1, 2011

By AIME AIME

EVERETTE LEE DEGOLYER, past President of the Institute and Anthony F. Lucas Medalist, was presented with the John Fritz Medal at a dinner at the Wal-dorf-Astoria Hotel in New York, Jan. 14. Dr. DeGolyer is the third representative of the Institute in recent years to receive the John Fritz Medal which is awarded jointly by the four Founder Engineering Societies through a board composed of sixteen past presidents. In 1938 Paul D. Merica was given the award "for important contributions to the development of alloys for industrial uses" and in 1933 the distinction was given to D. C. Jackling "for notable industrial achievement in initiating mass production of copper from low-grade ores through application of engineering principles."

Jan 1, 1942

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By William D. Dodge

A typical quality program plan is presented for explosion-proof (XP) electrical enclosures. The plan is suggested for manufactures of XP enclosures which are to be certified by MSHA for mining use. The plan describes the quality system, organization and implementing mechanisms which are to be applied in the manufacture and delivery of certified XP enclosures. Example forms and example procedures are included.

Jan 1, 1984

By D. Harrington

Hatch (260) made the following pertinent statement regarding the present status of engineering design of dust-control equipment: Textbooks on ventilation and engineering handbooks devote little or no space to methods of control of industrial dust, and in the technical journals papers on fundamental engineering design of equipment are conspicuous by their absence. In a recent bibliography of the literature on pneumoconiosis less than 1 percent of the articles dealt with the engineering control of the disease. The science of dust control has not developed beyond the stage of trial and error, and the design of structures for the suppression of dust is based almost entirely upon empirical data together with one or two elementary formulas. The latter were derived from the generalized experience in a limited number of Industries such as woodworking, where conditions and requirements are not at all like those, for example, in a sand-pulverizing plant. Wide experience and good judgment are essential to the proper use of the scanty information that has been collected and systematized. Without attempting to minimize the importance of experience in engineering design, it is necessary to point out that most of the past experience obtained in the empirical design of dust-control equipment was not evaluated by means of quantitative studies of the actual reduction in dust , fence, past experience does not necessarily furnish the proper guide for future design. In fact, recent surveys in certain industries, employing modern methods of investigation, have shown that existing equipment is in many cases inadequate.

Jan 1, 1935

By T Atkinson, A Cobb, R AJIington

Risk management is concerned with the whole spectrum of financial, geological, engineering, legal, governmental, social and occasionally ethnic issues, concerned with mining projects. The inherent risks in mining operations are well publicised, but new issues and hazards arrive on the scene and lake precedence, but the older risks still remain, while insurance cover may not he ‘full cover’ in the future. It has long been recognised that quantitative approaches to risk analysis can play a major role, but although these methods are capable of considerable theoretical precision, the lack of sound risk input data and experienced personnel limits the usefulness of theoretical analysis. It can, however, greatly assist in comparing cases, in identifying areas of risk and help in the investment decision process. Its major contribution to a mining project is that it imposes an investigative discipline that also assists in improving the quantitative approach to risk analysis and hence risk management. Risk analysis and risk management also requires sound common sense and major inputs from experienced geologists, mining, mechanical, electrical and mineral processing engineers. The Engineering Council, in 1992, issued a ten point code of professional practice entitled ‘Engineers and Risk Issues’ (The Engineering Council. 1992), covering our professional responsibilities, the law, our conduct, the need for a systematic approach to risk issues, the use of professional judgement, communications, risk management, evaluation of risk, our professional development in this field and the encouragement of public awareness of risk issues. This is a specific area of training perhaps long neglected by our industry and academic institutions (Atkinson. 1983).

Jan 5, 1996

By H. S. Auvil, L. D. Schmidt, H. G. Graham

"Several studies on the bulk density of coals prepared for byproduct-oven use were undertaken during the war by the Bureau of lanes in cooperation with the Office of the Solid Fuels Administrator and with the advice of the Coke Production Committee. The primary purpose of these studies was either to produce more uniform coke or to increase the throughput of existing facilities or both; the goal was increased Production of steel for war. As these studies were made, detailed reports were sent to the individual companies with whom the Bureau cooperated; also two reports,5/6/on the general subject of bulk-density control were published. In the course of the work, data were gathered that now prove of value in judging the merit of carious methods of testing bulk density and the limits of application of each method in byproduct-oven operations.Since the cessation of hostilities, the .Bureau section (Coke Production Survey Section) that conducted this work has been liquidated, but it was felt advisable to prepare a report on the accumulated experience so that it would be in a form available for the use of the industry and also as a base for any further research on the control of fluctuating bulk densities in coke ovens.It is hoped that the data and experiences recorded herein will be of material assistance to the many who have had difficulty in obtaining reproducible results in bulk-density testing. Since the data were gathered in the course of extending aid to individual plants in minimizing the deleterious effects of fluctuations in bulk density of oven charges on the quality and quantity of coke produced, certain desirable phases of an over-all investigation were not covered. However, on certain of these phases qualitative indications are available and the policy followed herein is that suggested by the American Society for Testing Materials Manual on Presentation of Data7/ that lacking quantitative information, relevant material should be included even though it ""may be qualitative in character, some may even be vague."""

May 1, 1946

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By Javier Illanes, Maurice Moore, Felipe Moroni, Rafael Acosta

Any organization that subjects its activities to a continuous improvement process must be able to adequately measure the results of the implemented changes in order to pursue better results over time. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators, such as P80 and fines percentage.

Sep 30, 2022

By M. Desjardins

The Hoyle Pond underground mine, located in the Porcupine Gold Camp, east of the city of Timmins, Ontario, Canada, is the cornerstone of Goldcorp Canada Ltd?s Porcupine Gold Mines. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. In order to meet increased flow requirements of 256 m3/s at the mine, a new Fresh Air Raise (FAR) and new surface fans were commissioned in early 2005. The newly acquired fans were capable of supplying the desired volume of air within a range of 1.5 and 2.0 kPa. Upon commissioning of the surface fans the total pressure was found to be exceedingly high; far beyond the design capabilities of the new installation. Consequently only one surface fan could be operated at any given time providing about half the required volume of air. Extensive work was immediately started aimed at reducing the system resistance in order to permit operation of the two fans in parallel and achieve the required mine flows. Larger booster fans were installed in parallel at the 900 m level, a 3 m raise bore linking the 450 and 900 m levels was developed to twin the existing fresh air circuit, and the FAR from surface to the 450 m level was twinned with the original FAR. This strategy, completed in 2012, resulted in a drastic reduction in system resistance and pressures, allowing the two surface fresh air fans to be safely operated in parallel and meeting the flow requirements. This paper describes details of the engineering design work and commissioning of the modified ventilation system, successfully ensuring the long term viability of the project.

Aug 1, 2013

By Frank Sames, Brad Terhune

In many construction projects and in most quarrying operations drilling and blasting remains the only feasible method of loosening rock in the removal of rock or overburden, the development of the quarry and in the production process of crushed stone. Often, a blasting plan is required for the project or the quarry’s permit with primary concerns over safety and site security, and compliance with environmental regulations or standards. From this plan, a blasting program has to be developed considering the varying requirements of production, the advance of the mineral extraction and the environmental impact. The actual blast design requires a planning and optimization process. This optimization process is driven by the blasting technicians/engineers, project or mine management and often by community concerns. The blast design process comprises the selection of blast parameters, including the explosives, and the actual layout of the blast. Design tools and controls range from conventional methods based on established blasting practices to advanced design tools or computer models. Blast monitoring and evaluation can also range from empirical to advanced blast assessment. The data and information from each blast or a series of blasts can further be used in the optimization process. Its success depends upon recording the data, the timely transformation of the data to relevant information, and the development of process oriented knowledge. The elements of the blast design process are summarized and described with examples of state-of-the art engineering controls. The reporting and monitoring of individual blasts is discussed with respect to data management and information systems. A conceptual overview of the components and interfaces of a blasting program is given and discussed on the background of technical, management and community concerns.

Jan 1, 2004

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

By D. F. O?Connor

The health & safety of all workers in an underground environment is paramount to the success of our operations. The diesel emission reduction projects are key to improving such an environment. However, care must be taken to reduce the risk to personnel during such tests and prevent exposure to other hazards. VALE Inco works in a close partnership with its unionized employees, manufactures, suppliers, researchers and government officials to ensure projects are done safely and efficiently to successful completion. The Creighton Mine Diesel Particulate Filter (DPF) project is an example of such a project that is currently under way to evaluate new and innovative technology that will further our search for improved environment for our workplace. This paper will discuss the issues and processes that are followed to ensure Diesel Particulate Filter (DPF) field tests are conducted safely and productively.

Jan 1, 2009

Jan 1, 1988

By G. J. Perrott, H. W. Clark

During the course of the cooperative smoke abatement investigation carried on by the Bureau of Mines , the city of Salt Lake and the University of Utah during 1919-1920 , a study was made as to the suitability of Utah coals for by-product coking with particular reference to low temperature coking . was done because it was realized that a smokeless fuel for domestic consumers was the best remedy for this class of smoke producer . A report of the technical side of the work was included in the final report of the cooperative investiga- Since this report was written (June 1 , 1920) further work has been done by other investigators .

Apr 1, 1922

By AIME AIME

WAR undoubtedly accelerates metallurgical progress, although its most obvious effect is a tremendous waste of materials. The necessity for restrictions in normal uses of metals results in a search for substitutes or for enhanced properties that will make a limited supply last longer. An insatiable demand for more metal to be produced more quickly favors trial of new processes, new metallurgical tools, and new methods of fabrication. Greatest advance is made, of course, in practical physical and process metallurgy. Theoretical or fundamental research necessarily must take a secondary position, and is so regarded in this review. It is not that developments in theoretical physical metallurgy are lacking entirely, but, following the same trend noted in other countries as they entered war activities, attention in the U.S.A. has been shifted strongly to those developments having an immediate practical application.

Jan 1, 1943