Search Documents

By William R. Beloff, Franklin M. Grynkewicz, Puza

Construction of the MBTA Red Line Extension through Somerville, MA, called for driving twin tube tunnels through a zone of approximately 83m (273 ft) with mixed face conditions. While the majority of the tunnels were driven through competent hard rock using drill and blast techniques, the mixed face zone was advanced using floating crown bars for primary support. The overburden consisted of medium clay, underlain by water bearing glacial till, over a sloping bedrock surface. Due to the unusual nature of the construction techniques, a program was undertaken by the Contractor to monitor ground movement and stresses in the temporary steel supports. This paper presents a description of the instrumentation employed, as well as the measured ground movements and support stresses. Additionally, the tunneling techniques are briefly presented and commented upon. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnel Contract is part of the Massachusetts Bay Transportation Authorities (MBTA) Red Line Extension from Harvard Square in Cambridge to the Alewife Brook Parkway via Somerville. The 5.1km (17,000 ft) Red Line Extension consists of four major new stations, three of which will be interlinked via tunnel construction, and the remaining station will be the last link of an open cut portion, and a terminal point for this phase of the extension. This 866m (2,790 ft) portion began at Porter Square in Cambridge and rose at a 4% slope through Somerville, terminating at the new Davis Square Station. Twin tube tunnels were constructed through 763m (2,517 ft) of rock and 83m (273 ft) of mixed face conditions at the Davis Square end. Figure 1 presents a plan view of the entire contract.

Jan 1, 1981

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By Doug Williams, Kent J. McGrew, Dr. Jack Murphy

For some time, selenate has eluded water treatment by conven­tional means such as precipitation and clarification. This has been due to the nearly universal solubility of all oxidized sele­nium species, the low levels required for surface discharge, and almost identical chemical behavior to all forms of oxidized sul­fur. The last characteristic makes selenate particularly difficult to deal with in acid mine waters where sulfate can easily be on the order of one gram per liter. Approaches such as ion exchange or reverse osmosis often tum into total demineraliza­tion schemes for the sake of removing a "trace" selenium species that may be present on the order of 108 sulfate/selenate. Reduction of selenate to selenite or elemental selenium by chemical means has been relatively unresearched. Some limit­ed success has been reported (Murphy, 1988) using ferrous hydroxide as a reducing agent; however, the reaction time as reported is too slow to be useful in a practical plant design. One significant difference between selenate and sulfate is that selenate has been discovered to be reducible in acid solution by elemental iron when catalyzed by soluble copper. Since the +4 or zero valence states of selenium are rather easy to deal with by coprecipitation with iron salts or alum, the elemental iron dis­solved in the process contributes to the overall process by pro­viding sludge upon raising the pH that can be separated by con­ventional clarification. Commercial production of selenium using copper catalyzed reduction of selenite to selenium metal via sulfur dioxide is well established, however, at the < 5 ppb requirements for surface discharge this reduction process equili­brates at levels far too high to be useful to low level selenate removal criteria. The reaction reported herein uses elemental iron for reduction of selenate with copper acting either as a cata­lyst or as a coprecipitation agent. This method, employed with conventional sludging, clarification and filtration can provide an economic method to achieve non detectable selenium (< 0.005 mg/I). Iron consumptions for the conditions tested have been on the order of 3 lbs/1,000 gallons treated. This represents as little as $0.06 or $2.00 per 1,000 gallons based on using a scrap source of iron or the purchase of electrolytic iron for the process.

Jan 1, 1996

By T. M. Barczak, Zach Agioutantis

The Support Technology Optimization Program (STOP) has been developed by the National Institute of Occupational Safety and Health (NIOSH) to provide a comprehensive tool for evaluating the performance of available secondary roof support systems and designs based on support strength, convergence, cost, installation time and material handling considerations. This program uses engineering models developed from full-scale testing of numerous supports under controlled loading conditions in the unique NIOSH Mine Roof Simulator load frame to determine the support load-displacement performance as a function of the various sup- port design parameters. Both standing supports, such as wood cribs installed within the entry, and intrinsic supports such as cable bolts, can be evaluated. Support systems can be designed and compared for use in a new mining section or to evaluate potential replacements for an existing design. The support design requirements are defined from 1) estimating the failure height in the immediate roof, 2) in-mine measure- ments of support and strata interaction or development of ground reaction curves from numerical modeling, 3) the performance of an existing support system, or 4) from any arbitrary load and convergence criteria. All settings can be saved to permit resuming an evaluation in progress at a later time. This paper presents the updated MS Windows version of this tool, which can be easily installed and run on a personal computer. This Windows implementation will feature a project and application scenario setup where multiple scenarios can be assigned to one project. Scenarios can then be compared on support parameters and cost. Cost parameters can be provided either as individual cost items or using a price grouping feature. Additional support performance curves and/or additional ground reaction curves will be distributed with program updates as new information is developed. Users can also provide their own support and/or ground reaction curves.

Jun 25, 2024

By Patricia O. Milley

Two years ago, AlliedSignal embarked on a journey to improve QUALITY. However, the focus of this endeavor was on the CUSTOMER and not the traditional product focus. It wasn&apos;t that a focus to improve product quality wasn&apos;t fruitful in the past. We&apos;ve practiced it in the chemical industry for many years with significant results. But our industry today is in a survival mode and yesterday&apos;s way of doing business is simply not good enough. In the mining industry, we have to make lug strides in how we do business or face losing our customer base. As you are well aware, other parts of the world are importing our technology at a rapid rate. We must work smarter to stay ahead of our customers ever more demanding need for higher quality at lower prices. With this as a driver, throughout the Corporation we reviewed in depth how we support our customers to keep them competitive and sought to eliminate work which did not help them reach this goal. Our first year of emphasis was on tools: how to hold meetings, gather data, and how to make decisions. This sounds very basic, I know, but you can&apos;t begin to imagine how productive meetings can become when you start with an agenda and prework delivered days in advance, and agree at the start of the meeting what should get accomplished. In the second year, we applied these tools to our work processes. We mapped how we do our work, scrutinized each step for value to the customer, and then set to work on how we could do things better. The areas we concentrated on were customer linked commercialization of new products, manufacturing and materials management. Our discussion today will focus on the commercialization of new products.

Jan 1, 1994

By F. P. van der Meer

Roller Press grinding has become an accepted technology in the cement industry, and finds a growing application in iron ore processing. Its introduction to the gold industry will depend on anticipated benefits such as a reduction in power requirements, the increase in throughput, and higher gold recoveries from the ground ore. The presentation highlights some of the specific features of the KHD Humboldt Wedag Roller Press and the effects of various operating parameters on the grinding result. Based on recent experiences examples are given on the use of the Roller Press in mineral applications. The anticipated reduction of grinding energy when using the Roller Press is discussed, together with the reduction in Bond Work Index.

Jan 1, 1997

By V. I. Lakshmanan, P. D. Tackaberry

The use of activated carbon as an alternative to Merrill Crowe precipitation to recover gold from pregnant leach solutions is recognized. Recovery using activated carbon, however, suffers from the interference, due to organic fouling, clay content and increasingly from the presence of elements such as copper. Ion exchange separation technology is familiar to the mining industry (uranium) and its potential application to the gold mining industry is evaluated with considerable efforts by research workers in South Africa, Australia, and North America. The present paper reviews in detail the status of the research work that identifies potential opportunities.

Jan 1, 1990

By H. Hejny

The objective of the project is to construct and operate a pan-European underground drainage and minewater management research centre, which would be the hub for data gathering and dissemination in real time of new data to users for analysis and interpretation, as well as serving as a model for consistency, for other centres at key water management sites throughout Europe which would feed data in real time through the hub. The data from the centre will be essential for informing River Basin Management Plans arising from the EU Water Framework Directive, which is an important driver for the project. The implementation of this Directive sets out a requirement for all Member States to develop River Basin Management Plans for all water resource systems. The facility would be a major contribution to sustainable water management in Europe.

Jan 1, 2007

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

The mining industry has indeed gone global. International minerals producers are spending big money to move into countries that were off limits a few years ago. Due mostly to political reasons, these countries&apos; huge mineral deposits - worth billions of dollars - were locked up and mining companies could only sit on the side and wonder "what if." Now much of the world is going the free market route. Once closed countries and developing nations are rewriting their mining and tax laws hoping to attract foreign investment to develop their natural resources. And big businesses - mining companies included - are lining up to get their share. But with new opportunities come new risks. While emerging nations are slowly accepting the free market concept and the privatization that goes along with it, many remain plagued with political instability and violence. Even developed nations carry their unique risks. Some of these include inadequate or contradictory legal and regulatory infrastructures, political patronage and outright corruption. So companies hoping to expand into new regions of the world must do more than examine the market. They must study the political stability and structure of a country, as well as its tax and environmental laws. And they must guarantee the safety of their employees. Control Risks Group is an international management consulting company that assists companies preparing to move into a new country. It employs about 225 people in 14 offices throughout the world. Control Risks personnel include lawyers, bankers and former law enforcement officers and intelligence people. The company held a one-day seminar in Washington, DC to update some of its clients on the state of affairs in various regions of the world. The seminar also covered extortion, corruption and product diversion. About 175 people attended the seminar. Speakers included Control Risks&apos; operators, analysts and investigators. Here is a summary of what some of those people had to say.

Jan 1, 1998

By L. U. Spellman

Atlantic Cement Company&apos;s new multimillion dollar, 10,000,000 barrel per year cement plant went into full operation in February, 1962, bringing into reality a new concept in the distribution of Portland cement. The Cerro and Newmont Mining Corporations, well established in the mineral extraction and dressing industry, backed the venture. To take advantage of the, economics inherent in single production units of large capacity, it was necessary to first find a market&apos; capable of absorbing such large quantities. Cement can be economically shipped by rail and truck about 200 miles. Beyond&apos; that radius from the producing facility the freight costs become prohibitive. No single marker area within that radius exists which could absorb such a large volume of cement. However, water transportation provides a relatively inexpensive method of transporting bulk products many times over such a distance. Thus, it was decided to locate the producing facility near a deep water port which had ready access both to the Atlantic Ocean and, just as important, a good source of raw material. An extensive feasibility study was made and the site at Ravena, New York on the Hudson River near Albany was chosen. Here, vast quantities of limestone in the foothills of the Catskill Mountains are found within a short distance of-the deep-water Hudson River.

Jan 1, 1964

By Duane A. Smith

Horace Tabor. No 19th century Colorado mining man is better known but, unfortunately, probably less understood. He is little appreciated for his significant contributions to the industry and the state. A century ago, Tabor was headline news. The legend today, however, has become so all pervasive and so interwoven with fact that the two are hard to separate. For example, he never told Baby Doe on his death bed to hang on to the Matchless mine. Yet this has emerged as staple Tabor fare. So much attention has been focused on his matrimonial triangle that it overshadows the man. Symbol of mining&apos;s reward Tabor traveled west in the 1859 Pike&apos;s Peak gold rush. In the next generation, he came to symbolize the rewards mining might lavish on an individual. The Leadville Daily Herald (Sept. 10, 1882) could write, without exaggeration, that "the extent which the mining industry of Colorado is under obligation to Tabor cannot be easily estimated - what he has done for Leadville and Denver is patent to all." It had not come easily, nor had Tabor started out a success. His early placer mining at Payne&apos;s Bar, near present-day Idaho Springs, CO, had turned no fortune. So in 1860, he, his wife Augusta, and son went south to Colorado City, then over Ute Pass and up the Arkansas Valley to Oro City. Arriving soon after the initial discovery, Tabor staked a good claim. With a sharp eye, he and Augusta broadened their base by establishing a store. Both mining and business would pay dividends in the following years. By the season&apos;s end, though, Oro City was already declining. Always on the lookout for a richer district, Tabor and his family moved the next year across the mountains to promising Buckskin Joe. The familiar pattern followed, with the store and post office being the center of their attention. Mining investment and management now replaced the earlier physical panning and sluice operating. Seven years later, the Tabors abandoned Buckskin Joe and returned to Oro City. It had moved up California Gulch to be near the district&apos;s best mine, the Printer Boy. Middle class was not enough Middle class respectability, plus a steady income, was the Tabor&apos;s by the 1870s; fine as far as it went. But it proved far from the fortune Horace had always been seeking. Oro City languished in the backwash of Colorado mining and Tabor seemed like many men who had drifted around the Territory following the ebb and flow of mining. His faithful wife Augusta had been a steady factor in the success the family achieved. She helped year after year to operate the store and post office. Not simply the happy-go-lucky individual he has often been portrayed, Tabor was a hard working businessman/mine owner. An R. G. Dun and Company agent evaluated him in 1876 "Net worth $23,200. Is a very shrewd businessman and not liable to lose money, has a good chance to make money as he had no competition." Leadville: Tabor&apos;s silverlined-fortune After all those years on the Colorado mining frontier, in 1877, Lake County&apos;s wealthiest and most respected merchant made another move. It was short in distance, only 4 km (2.5 miles) down California Gulch, then a little north to a new mining camp. This new camp, soon named Leadville, gave birth to the Tabor fortune and legend. Middle-aged (Horace was 47), the Tabors once more set up their general store and found themselves in the midst of the open¬ing of a new district. This time silver beckoned and not the gold that had brought them West 18 years before.

Jan 1, 1989

By H. M. Conger

I&apos;m really very pleased to be talking with you today about the environmental impacts of gold ore processing as part of this symposium on emerging process technologies for a cleaner environment. But before I talk about some of the newer developments that are coming, I would like to set the stage by reviewing some of the recent past. Over the last decade or so the U.S. gold mining industry has experienced remarkable growth, primarily in heap leaching operations, and not surprisingly there has been parallel growth of environmental regulations. At Homestake, we have had the excitement of bringing on-line a new mine embodying state-of-the-art technology and environmental planning, and during the same period the flagship of our company, the Homestake mine, has been brought into modern day compliance through the application of innovative environmental technology. This has been a learning process; in both cases we found that we had to develop new ways to meet our objectives. At our McLaughlin mine in California a major achievement was pioneering the use of pressure oxidation, or autoclaves, for refractory gold ores, and at the Homestake it was the development of a unique bio-treatment plant for wastewater. These projects were developed balancing operational goals, environmental concerns and costs, and I would submit that being cost-effective is our greatest challenge in the development of new, environmentally sound, process technology. In meeting that challenge, our job has not been made any easier by the myriad environmental laws and regulations that directly affect the design and operation of our facilities. Most of these constraints have evolved through the political process more or less independently, but in their application there often are over-lapping provisions. Adding to this complexity is the fact that action takes place in both state and federal arenas. As a result, state and federal roles sometimes become intertwined, and a good case in point is provided by various cyanide issues faced by gold producers. The vast majority of U.S. gold mining takes place in the so-called "mineral States," the western States that come under the Mining Law of 1872 as amended. This is the basic statute that provides for access and tenure to develop mineral resources on federal lands in those states. There is gold mining outside the defined mineral States, and there is also gold mining in the mineral States on private lands. Our own Homestake mine in South Dakota is one of the best examples of the latter category: located entirely on private land, it is nevertheless subject to at least 13 federal environmental statutes and some 29 federal regulatory requirements. There are also nine significant state statutory and regulatory requirements that apply. On federal lands in the mineral States there are numerous federal statutes and regulations which affect mining, over and above the current Mining Law. These, which are in addition to the laws applying to private land, include the National Environmental Protection Act and the Federal Land Policy and Management Act, among others. Still, those who advocate radical changes in the basic Mining Law would have us believe that sweeping environmental protection and reclamation provisions, not to mention new land use restrictions, are needed. Such changes could effectively prohibit mining on the federal public lands. Strict enforcement of our current Mining Law would have presented most of the abuses cited by the critics but if the Law is to be changed at all, I believe that, at a minimum, the principles of self-initiation and security of tenure embodied in the present statute should be maintained. These are critically important concepts, but there are other statutory and regulatory issues constantly before us as gold miners. Let me cite a few examples: Reauthorization of RCRA There are several bills being considered by Congress to amend the Resource Conservation and Recovery Act (RCRA) that have as their theme

Jan 1, 1992

By S. Eugene Sankey, Geoffrey L. Payne

Fundamental choices in flocculant selection often come down to the lower cost of solid grade products versus the convenience of liquids. The ideal product would be a low cost solid grade flocculant which requires minimal handling and no sophisticated dissolving equipment. Recent polymer developments have lead to the commercialization of a limited range of dry polymers that can be screw fed at controlled rates directly to process streams without the need for predissolving. Other developments include dry polymers that can be directly added to mix tanks without the need for sophisticated wetting systems. The latter will make dry flocculants especially attractive for smaller users. Examples of these new products and their application in industrial and municipal waste treatment will be provided.

Jan 1, 1994

By M. C. Roberts

Metal producers are now suffering through a major downturn in prices for their products even though it has only been a few years since they were enjoying high prices. From an historical perspective, the current situation is another of the cyclical downturns that often occur every five to seven years. This paper uses time-trend decomposition techniques to identify the cycles and statistical methods to find the duration of these cycles for a variety of metal prices. Given some idea of how long and severe these cycles typically are, the mining industry can better plan to weather the downturns and take advantage of the upturns. For example, timing investments in new projects to take advantage of the cyclical upturns can dramatically improve project profitability.

Jan 1, 2003

By R. E. Mclaughlin, R. J. McLaughlin, A. H. Danzberger

Acid mine drainage (AMD) can occur as a natural phenome­non through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhib­it low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations - the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiqui­tous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treat­ment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper. Within the family of chemical treatment processes, there are three principal recognized methods, namely, "Conventional," "High Density Sludge" (HDS) and "Heavy Metals Removal Process" (HMRP). All three are now employed or specified for treating AMO at mining sites which are being reclaimed under Superfund. Only limited data are available for more specialized chemical treatment processes such as "ferrate", borohydride membrane and electrochemical methods. Therefore, these data are not included here. Performance data for these three processes are presented in this paper and comparison among them is made. Comparisons include consideration of water quality, sludge characteristics, and operational ease. Capital and operational cost comparisons of these processes were addressed in a previous paper by the authors (see bibliography). The results presented here are impo1tant not only to metals mining, but are also applicable to other industries experiencing metals-laden acidic wastes including: coal mining and prepara­tion, metal plating, and electronics circuit board manufacturing. The acceptance of any process should be based on bench scale demonstration before implementation is contemplated. The three processes included herein are discussed in relation to the particular sites at which they are in use, or their use is planned. The sites selected were representative of the various types of processes and the wastewater parameters.

Jan 1, 1998

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By D. U. Gustafsson

After half a million meters drilled with Wassara we are now confident that ITH hammers powered with simple water will become an established product for production drilling. Today four drill rigs in LKAB Malmberget equipped with Wassara drill about 25 000 m per month of 4 1/2" holes. In Kidd Creek, Canada, Was sara is used for production drilling in stopes with good results. The first Wassara 6" hammer has drilled a 36 meter long, completely straight horizontal cut hole for drifting in the LKAB Malmberget Mine. Main advantages are about doubled penetration rate, very good air quality and improved hole cleaning which facilitates stabilized drilling. Disadvantages are resistance to new technology and, in some cases, the increased use of water.

Jan 1, 1995

By Richard R. Klimpel

In this paper, the old and the new commercially available reagent chemistries for the improved flotation of sulfide minerals will be summarized. The reagent classes discussed are those that meet three criteria: 1) they are being commercially used and/or large scale plant tested in North America in the last few years; 2) they are clearly different in chemical structure than commonly used commercial reagents of the last few decades and are not simply mixtures of existing reagents and/or simple changes in cation, alkyl group size, etc. and 3) the structural formulae are clearly specified in the public literature.

Jan 1, 1994

By M. Galetakis

This paper proposes a new approach for calibration of dual gamma-energy transmission (DU-ET) ash analyser for improved online analysis of run-of-mine lignite. An adaptive neuro-fuzzy inference system (ANFIS) was developed to model the relationship between the intensities measured by the scintillation counter of the analyzer and the measured ash. Samples collected from Megalopolis lignite mines were measured for their ash content by using standard laboratory methods as well as by DUET. Obtained data was divided into training, testing and validation sets. A first order Sugeno type ANFIS was used in conjunction with early stop training. The calibration performance obtained by this approach was significantly better compared with that obtained by standard calibration methods based on multiple linear regression analysis.

Jan 1, 2006