Search Documents

By Joseph L. Condon

The U.S. Department of the Interior, Bureau of Mines, is doing research on methods to obtain premining information on problems such as detection of old mine workings, abandoned oil wells, channel sands, faults, and other geologic features that are undesirable from a production or safety aspect. Techniques being developed to acquire the necessary information include seismic and electromagnetic. The seismic methods include high-resolution seismic and acoustic methods applied from the surface and inseam channel waves applied under- ground. The electromagnetic, or radar, methods are applied from the surface, from boreholes, and from the working face underground. All of these methods are useful under certain site-specific conditions, but none of these methods is universally applicable for all mining conditions.

Jan 1, 1980

By A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneuna.cic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 3000 cons per hour (2700 t(h) to the backfill level, situated about: 2000 feet (610 m) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1978

By John J. Mancini

Elastomeric liner products have been used for over two decades in a wide variety of uses including pond liners, hazardous waste barriers, dam face rehabilitation and mining applications. Asphalt blended with polymers is enjoying renewed interest in the engineering community because of its durability, high yield attributes, fewer CQA steps due to seamless installation, and ease of installation and repair. As in other lining technologies, advancements in polymer chemistry and improvements in installation techniques have had dramatic impact on the quality of fluid-applied asphalt (FAA) membranes. Membrane 6, man­ufactured by Deery Oil, Inc. for over 16 years is a hot-applied polymer modified asphalt membrane that can be applied to a variety of substrates in a reinforced configuration or installed directly on an asphalt surface. By blending thermoplastic polymers with asphalt, very favorable stress/strain characteristics can be achieved (Chambers, 1980). Typically the membrane will yield under rel­atively low stress and also exhibit high elongation capability. In service applications where puncture resistance is a concern, fluid applied asphalt materials have the flexibility and com­pressive strength under heavy loading that leach pad designers may find attractive. Additional security is achieved if long term service life is important as in the case of radioactive waste con­tainment. The Department of Energy selected Membrane 6 over seamed liners for a surface barrier that must isolate and contain radioactive waste for 1000 years. Asphalt has a long history of use as a water-stop material and it is believed that this natural construction material combined with SBS polymers will per-form for a millennium. (Freeman, 1994) The process of installing Membrane 6 varies according to job size and the type of surface to be protected. Lining applica­tions on compacted substrates require the membrane to be applied to a scrim cloth (fig 1). Some early pioneers in FAA technology neglected this step and therefore never achieved per­formance levels that satisfied regulatory guidelines. The scrim provides a cohesive surface that promotes membrane flow while achieving high impermeability (2Xl0 '11).

Jan 1, 1996

By Mike Wongkaew, Brandon Kluzniak, Per Vilhelmsson

Rail access to Ontario International Airport (ONT) has long been a goal of San Bernardino County Transportation Authority (SBCTA) to increase public transit options to ONT and provide incoming ONT passengers improved access to San Bernardino County and the greater Southern California region. This paper describes the planning for the Design-Build-Operate-Maintain (DBOM) delivery of an emerging technology tunnel connection between the Rancho Cucamonga Metrolink station and ONT. The paper discusses key technical considerations, challenges, and opportunities; conceptual configuration development; and construction planning and establishment of the footprint for the underground connection.

Dec 1, 2022

By R. N. Chakravorty

Spontaneous combustion presents a very serious hazard to both safety and economics of mining operations. Notwithstanding considerable research that has been done over the years to present and control spontaneous combustion the risk still exists. Consequently, this problem poses a major challenge to mine safety researchers; new and improved techniques are constantly being developed to deal with this major hazard. This paper reviews the current practices to prevent and control spontaneous combustion in coal mine operations highlighting new developments in this area. Research and development work presently being carried out in Canada to' deal with this problem is also discussed which includes monitoring, inertization and application of biotechnology.

Jan 1, 1988

By L. E. Murr

Solution flow in leach dumps and heaps or in columns of representative rock has been the subject of only limited studies. This is a regime involving unsaturated flow in semiconsolidated rock with a wide size distribution. Even the concepts of continuous flow systems are fairly recent, and have evolved from the search for better methods of operating industrial chemical reactors. (1-3) Waste rock consolidation and permeability play a key role in solution flow characteristics. Harris (4) suggested that bulk density variations in a leach dump could alter the particle-to-particle contact, and that large particle aggregates could act like single, large particles . In the limiting case where the bulk density approaches that of the undisturbed, consolidated rock, the entire waste unit would behave as a single particle. Roman (5) treated the phenomenon of bulk density and its effect on consolidation in terms of lixiviant flow paths or solution channeling in leach dumps. Like Harris, he assumed that no solution moved through particles or particle aggregates associated with zones of high bulk density. Solution flow paths are thus effectively separated by particle regimes, creating solution channels in the waste body. While some attempts have been made to describe solution flow in leach dumps and related systems by utilizing computer model approaches and laboratory- scale simulations (5,6), there have been no direct, large-scale observations of solution movement in channels or of the actual channel sizes and distributions within a waste body. This paper describes a series of experiments involving large-scale, controlled waste leaching tests, conducted over a period of several years, and aimed at providing some direct observation of the changes in waste consolidation and permeability, the size and distribution of solution channels, the movement of such channels with continued solution application, and other features relating to solution flow during the leaching of low-grade waste. These results are then combined with mineralogical information to explain observed leach behavior.

Jan 1, 1981

By C. Jardine

The concept of the system is to minimize costly unscheduled breakdowns of equipment by replacing components earlier than their "life" expectancy. Periodic unit services are scheduled according to pre-set constraints. Service sheets are generated by matching a job and component master listing based on assigned cyclic component lives. The system can provide accountability of all man-hours reported and history information can be selectively retrieved. By reducing unscheduled equipment shutdowns, this system allows for better utilization of manpower and an overall improvement in equipment reliability and availability.

Jan 1, 1979

By Giuseppe Gaspari, Xiangrong Wang

The pandemic emergency is forcing transit agencies to define strategies allowing social distancing, which are more challenging in underground interchange stations in crowded downtown cores. Toronto Transit Commission’s (TTC’s) Bloor-Yonge Station Capacity Improvement Project in Toronto was approved to meet increasing demand and represents an opportunity to fight COVID-19. This paper discusses cost-effective solutions in expanding the cut-and-cover station box over the existing Toronto Subway Line 2 and connecting it through ventilation openings in the cast-iron tunnel liner. Potential uplift risks and structural damage due to minimal vertical clearance were analyzed via three-dimensional finite element analyses with advanced constitutive laws to simulate the multi-stage construction process. Based on the simulation results, a series of countermeasures, including excavation support systems, king posts, ground-consolidations, and liner reinforcements were integrated into comprehensive design options to ensure the serviceability and structural integrity of the subway tunnels.

Jun 13, 2021

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

By H. Nemutolluhi

Discussion by G.E. Agar In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to he done, wet or dry or a combination? On top of that uncertainty the author refers to a simplified "Anaconda" test. No reference is provided for this procedure and in the text the results of the technique are referred to "Denver wet ball mill" results and say nothing of Anaconda results. Reply by H. Nematollahi I think that the method proposed to determine the Bond Work Index in this paper is clearly described in the paper as follows: •The method of grinding is dry (Ref. paragraph I, subject Method description); •The size of ball mill, the quantity and size of balls are noted (Ref. paragraph 1, subject Test equipment); and The test procedure is described in detail (Ref. paragraphs 1, 2 and 3, subject Test procedure). As it is noted in the paper, the test has been worked out under the same condition as Standard Bond Test with ball mill, so dry (screening should be dry also), but using a smaller ball mill and a smaller quantity of sample. Considering the above mentioned points, I believe that the method has been fully and clearly described and it ought to be repeatable as well. The Anaconda test is a method for determination of Work Index and could be done by any types of laboratory wet ball mill (Yan, R.F., et al., cf. References). I applied this method using a laboratory Denver ball mill (Ref. paragraph I subject Determining the Bond Work Index). So the results referred to Denver wet ball mill can be equated the same as Anaconda method.

Jan 1, 1996

The surface of chalcopyrite was studied in situ in aqueous solution by an atomic force microscopy (AFM). The AFM images showed that some absorbate in patches was detected on the mineral surface, after the chalcopyrite sample was soaked in 5x10-4M potassium ethyl xanthate (KEX) solution at pH 11 for 10 minutes. These patches increased in size with time elapsing. At the same time, as shown by the obtained AFM force curves, the adhesion between the AFM tip and the substrate increased greatly due to the adsorption. Rinsing with ethanol removed the absorbate from the chalcopyrite surface, as well as the big adhesion observed in KEX solution.

Jan 1, 2010

By William Gleason

The evolution of technology has made the world a more connected place. It continues to change the way we power our homes and vehicles and is leading to a future that seems to be limitless. Limitless as long as we can continue to supply the minerals necessary for technology to produce better iPhones, more efficient electric cars, better wind turbines and sophisticated national defense systems. These minerals, dubbed critical minerals, have surged in importance in every corner of the world and, on Aug. 3-4, they were topic of conversation at the Critical Minerals 2014 conference in Denver, CO. The conference, hosted by SME and the Australasian Institute of Mining and Metallurgy (AusIMM), looked at critical minerals from every angle, from where they are found to what the future might be. Among the minerals that have been called critical are rare earths, a collection of 17 minerals that have become increasingly important as technology continues to advance in everything from communications to energy to national defense. Leading off the conference, David Abraham, senior fellow at the Institute for Analysis of Global Security, explained that, like many people, he is relatively new to rare earths. Unlike most people, though, Abraham developed more than a passing interest in the minerals and has since travelled the world to understand the role of rare earths ? where they are found, how they are mined, how they get to market and, eventually, what applications they are used in. Following his travels, he said he returned concerned about the sector and how the industry will keep up with the demand that only seems to be growing in the modern world. And, Abraham noted, that it is not just the developed world that is driving demand. It stretches even to places like Indonesia, where the average annual income is about $3,000/year. Yet, the nation is one of the most active places in the world for social media with a population that is wired in with all kinds of electronics. The problem facing the sector is, and has been for a long time, and especially since 2010, supply of the minerals. At one time, China produced about 98 percent of the world?s supply and controlled the sector completely. In 2010, as the world began to demand more rare earths and develop other sources, China announced an export ban on rare earths. This changed the game completely, from the production lines all the way to the floor of the U.S. Congress.

By Mark G. Aylmore, Eric J. Grimsey

Anenopyrite, both pure and in some cases associated with pyrite, was laboratory roasted either isothermally or at a constant heating rate, at temperatures mainly between 723 and 923 K and under environments of air, sulfur dioxide, oxygen and argon, as well as S02/02/H20/N2 mixtures. The mineralogy, arsenic contents and in some cases surface areas of the calcines were evaluated so as to provide an enhanced understanding particularly of the conditions under which the important transformations to pyrrhotite and magnetite occur. A thermodynamic analysis is also undertaken to rationalize the observations and provide some guidance for the operation of commercial roasters.

Jan 1, 1990

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov

As a result of thermodynamic analysis of a mineral-sodium, oleate-water system, flotation and adsorption tests at various pH values, and sodium oleate concentrations, it has been established that due to regularities of phosphate-containing minerals (fluorapatite, hydroxyapatite, carbonatapatite) flotation cannot be explained by the formation of alkali-earth metal oleates on their surface. This paper presents a novel theory that connects optimal conditions for mineral flotation with zero charge of its surface, which can explain the regularity of minerals flotation observed. The quantitative physicochemical flotation models developed based on the theory are suitable for improving industrial processes, conditioning of recycling waters, and application in automatic control systems at the plants. Key words: apatite, oleate, flotation, modeling, control, and regulation.

Jan 1, 1999

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

By Robert W. Bartlett

Both hydrometallurgical and vapometallurgical processes often involve ores that have been previously ground and size classified. When the valuable mineral is substantially liberated, the chemical reaction is likely to occur on the particle surface and the particle core will shrink as the reaction proceeds. If the chemical reaction products are solid materials then a solid shell, usually porous, will form around the shrinking core. This is known as the core/shell or topochemical reaction model. Using a spherical approximation for the particles, equations have been developed to express the extent of chemical conversion of the particle, depending on which one of the following process or mass transport steps is rate controlling:1 (1) chemical reaction at the particle surface, (2) diffusion through the thickening reaction product shell or (3) mass transport through a boundary layer surrounding the particle. In a previous paper2 these equations were coupled with the Gates -Gaudin-Schuhmann equation 3 4 describing the distribution of particle sizes resulting from comminution of rocks and other brittle solids to develop reaction yield curves expressing the weight fraction of metal or other valuable component of the feed that was chemically converted as a function of residence time. This was done for (a) batch, (b) continuous plug flow and (c) continuous back-mix flow (continuous stirred tank) reactors or process vessels. To make the curves of general rather than special utility, the residence time (average residence time for back-mix reactors) was normalized to a dimensionless time by dividing by the time required to completely chemically convert the largest particle in the feed to reac-

Jan 1, 1972

By B. Yarar, R. Buchan

Mineral-processing techniques were adopted for use in the separation of various plastics used in beverage bottles. A complete flowsheet, which utilized size reduction, heavy-media separation and flotation, was developed to separate PE, PVC and PET. In addition, the mixtures contained cellulose fibers (from labels) and aluminum (from bottle caps). It was demonstrated that, while heavy-media separation allows for the separation of a PVC/ PET mixture, froth flotation can be used to separate PVC and PET. For this purpose, the differential action of a pH 11 alkaline aqueous solution containing methanol and MIBC as surface-tension control agents, has been found to be a suitable flotation medium. This paper reports on some aspects of a flotation flowsheet that was developed for the separation of plastics contained in municipal solid wastes.

Jan 1, 1997

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By Jr. Kirschner

An abandoned waste impoundment located within a portion of the Kellogg, Idaho Superfund site constitutes a field research area for studying the feasibility of recovering heavy metals in-situ from unsaturated mine and mill wastes. A prototype in-situ leaching cell has been evaluated using liquid-phase tracer tests and other hydro-geologic tests prior to introducing a lixiviant. The results of the tests suggest that: (1) the cell can be operated excursion-free with a low-density lixiviant at an injection/withdrawal rate of approximately 0.32 l/s; and (2) each hydro-geologic unit is highly heterogeneous at the different scales studied.

Jan 1, 1993

By Diómedes Sarmiento

Centromin is a Mining Company owned by the peruvian government. It&apos;s considered as one of the major mining and metallurgical center in Latin America. The main operations of the Company are: Mining, Concentration, Smelting and Refining of several metals (Figure 1). At present, dentromin operates with six mining units: Cerro de Pasco, Morococha, Casapalca, San Cristobal, Yauricocha and Cobriza; which are located in the Central part of the country between 2 100 m and up to 4 800 m above sea level. The installed capacity of concentration all together ranges about 14 000 tons per day. There&apos;s also a metallurgical plant in La Oroya with a production capacity of 220 000 tons per year of refined metal. The production of the Company is diversified in twenty two (22) final pro- ducts, whose major productions are : copper, lead, zinc, silver, gold, tungg ten and bismuth. The minor products are: arsenic, antimony, cadmiun, teluriun, sulphuric acid, indium, selenium, etc.

Jan 1, 1979