Search Documents

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics The analysis suggests grinding depends mainly on the state of aggregation of the ground products inside the mill and pulp fluidity Implications of the observed effects on ultrafine grinding in general are discussed

Jan 1, 1983

By D. M. Muir

Thiosulfate offers a nontoxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32; It is shown that an understanding of the copper speciation and sulfur speciation is required to optimize this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2002

By Robert E. Hershey

The phosphate industry is the fourth-ranking mineral industry in Tennessee; it has an annual value of 13,000,000 and a yearly production of almost 2,000,000 tons of phosphate ore. Tennessee, at present, is second in rank of phosphate production in the United States. In accord with the importance of this mineral commodity, the Tennessee Division of Geology, is conducting a continuing study of the industry' and the raw s, materials upon which it is dependent. Of the three type's of phosphate found in Tennessee, the brown phosphate rock of the Bigby faces of the Bigby-Cannon limestone is by far the most extensive in occurrence and is the only type being mined at the present time. Because of the importance of the brown phosphate ores, our Division has mapped , in detail the outcrop pattern of the Bigby facies of the Bigby-Cannon limestone. The geologic mapping was done by Dr C. W. Wilson, Jr. and others under his super-vision and the geology plotted on 7 1/2-minute topographic maps, with scale of 1 to 24,000 or 1 inch equals 2,000 feet. These maps will be available for use in the near future and will be published later-with complete geologic coverage.

Jan 1, 1960

By Ian Larkins

The Ruby Hill Mine agglomerates crushed low-grade ore (nominally -1 .5'') with high-grade filtered tailings (filter cake, nominally 80% -65#). Cement is added as a binding agent. The agglomerated ore is then conveyed and stacked on the heap. In 1998 approximately $480 000 was spent on cement for agglomeration. Cement for mill pH control and agglomeration was the largest single reagent cost at Ruby Hill. In an effort to reduce agglomeration costs a test-work program was initiated to investigate alternative binders and optimum binder additions. This paper summarizes the test­work results to-date.

Jan 1, 1999

By A. Juganda, H. PINHEIRO, J. Brune, N. SANDOVAL, G. Bogin, K. Gallagher, F Wilson

The present work discusses the nuances of scaling and flow similarity to develop a 1/40th scale version of a longwall coal mine. Details on the geometric, kinematic, and dynamic scaling of the physical model are presented and discussed. This works also discusses using a 30% CO2 – 70% He gas mixture as a surrogate for methane. It also presents the implications of various Reynolds numbers (ranging from 7,000 to 140,000) and rotation of the shearer drums in the dynamic representation of the airflow and gas mixtures in the physical scaled model.

Mar 19, 2022

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

By K. F. Unrug

The identification of the major subsidence areas in the Western Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential. It is recommended that further site specific studies should be performed on this area.

Jan 1, 1986

By Juan C. Diaz, Juan P. Carmona, Manuel Z. Salgado, Oscar J. Restrepo

The “Teaching Kids” project is an educational initiative for young people and children from elementary schools. It is carried out by Mining, Geological, and Environmental Engineering students from the SME Student Chapter of the Universidad Nacional de Colombia, Medellin. The primary purpose of the Teaching Kids project is to share knowledge about geosciences and mineral resources in a didactic and attractive way, emphasizing the importance of identifying the use of minerals in daily life and responsible and sustainable mining in our society. Furthermore, this project aims to promote the importance of pursuing geoscience majors in the new generations and improve the mining industry’s public perception. Different methodologies related to early childhood education are implemented, such as gamification, in which the dynamics of games are adapted during the development of workshops to teach and learn in an active and motivated environment. Furthermore, the Montessori Method is used. It implements textbooks, sensory mineral boxes, and presentations to allow learning through experimentation itself (Montessori 2003). The implementation of this methodology has been successful; it has shown high engagement, participation, and retention of the basic concept of geoscience and mining.

Feb 1, 2025

By F. G. Crack

This paper is based on the philosophy that the management structure and strategy required for mine construction and development projects are different from that required for routine production and maintenance operations in a mine. The purpose of this paper is to present an integrated approach to the management of mine development projects. This paper highlights the four major aspects of the integrated approach. First, a brief review of the various types of contract documents is provided. Second, the management organization of a project is discussed. Third, the project manager's role and the field supervisor's responsibility are briefly outlined. Finally, the use of scientific techniques for planning, scheduling, executing, and controlling projects is presented. Each of these aspects is important; however, each by itself cannot be expected to bring order or unifying impact to the complexities involved in overall project management. When all these aspects are coordinated, the result will be a sore successful project from conception to completion.

Jan 1, 1982

By Brij M. Moudgil

Florida produced more than eighty percent of domestic phosphate during 1974. This amounted to more than thirty-five million short tons. Ninety percent of this production was used in the production of fertilizers. Other uses of phosphate include food preservatives, fabric dyes, optical glass, photographic films, soaps, plastics, pharmaceuticals and animal feed ingredients. Marketable phosphate rock projections for the nest decade forecast a very healthy growth for the Florida phosphate industry. Associated with the expansion, however, are the corresponding problems of water conservation, air and water pollution and land reclamation. Recognizing mining as an interim land use, the industry is presently engaged in a very active reclamation program. The proximity of the central Florida deposits to rapidly developing urban areas makes it important to undertake successful and well planned reclamation programs. Water use and conservation is of vitil importance to the industry. Water withdrawal from existing aquifers and discharges into drainage systems are closely regulated by state agencies. Water is stored and recycled to maximize usage. In some instances water is even returned to major aquifers through a series of recharge or connector wells. The phosphate industry has spent over 200 million dollars in the past decade for research, development and implementation of pollution abatement and water conservation systems.1 The following discussion outlines various phases of phosphate mining in central Florida today, with emphasis on research in waste disposal techniques and progressive land reclamation programs.

Jan 1, 1975

By S. Ubaldini

Acid mine drainage (AMD) is a common problem in different areas with a past history of mining activities, which is characterized by low pH (2-4.5) and significant toxic metals concentration. The main aim of the present work was to perform a process feasibility analysis in order to remove heavy metals (Cd, Zn, Ni, Mn, Cu) from AMD (Acid Mine Drainage) in a relatively cheap and environmentally friendly way, by means of electrowinning and biosorption. A first characterization of an Italian AMD sample was performed evidencing a zinc concentration around 2 g/L, cadmium and nickel content of about 4 mg/L, manganese of 85 mg/L and iron 190 mg/L. Electrowinning tests lead to the following metal removal after three hours treatment: Zn 99%, Ni 99.9%, Cd 99.9%, Cu 99%, Mn 87%, Fe 96%. Moreover, an high grade of purity of the metal deposit has been achieved (Zn>95%), as observed by X-ray diffraction analysis. Considering that metals concentration in the effluent was still above legal limits (in particular for Zn, Mn and Fe), a further biosorption treatment was planned in order to produce an effluent fitting environmental limits. Experimental electrowinning tests and literature multimetal column biosorption data have been used in order to perform a preliminary techno-economic feasibility analysis of the process aimed at metal removal from AMD. A treatment cost of about 6.5 ?/m3 AMD has been estimated, for a plant capacity of 10 m3/h AMD inlet flow rate.

Jan 1, 2006

By X. Cui, H. Ding, J. Wen, Q. Gu

This study is a continuation of previous work designed to further explore the mechanism of the bioleaching of sulfide concentrate at neutral pH by heterotrophic bacteria Bacillus megaterium QM B1551. The concentrate contained 13.2 percent nickel (Ni) and 0.2 percent cobalt (Co), which presented primarily as pentlandite and pyrrhotite. Contact and noncontact bioleaching experiments were conducted with finely ground ore at an initial pH of 6, resulting in 44.7 percent of Ni and 38.2 percent of Co leached in the contact-bioleaching treatment. Oxidation experiments of sulfur, thiosulfate (S2O32−) and ferrous ions (Fe2+) by cell membrane were performed to verify whether sulfur transferase, thiosulfate quinone reductase and enzyme cytochrome B558 on the surface of the bacteria could be expressed to oxidize the sulfide. The results show that thiosulfate quinone reductase and cytochrome B558 could be expressed to oxidize S2O32− and Fe2+ to SO42− and Fe3+, respectively.

By Philip D. Lindahl

The US Bureau of Mines (USBM) began research to improve the safety and efficiency of transporting coal from underground coal mines using a balanced air-lift hydrohoist (ALH). ALH includes a U-tube pipeline that can be installed through an existing shaft or two surface-drilled holes connecting the mine level to the surface. Bench- and pilot-scale models were tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a riser pipe by injecting compressed air microbubbles. A prototype injector was developed that continuously compacted -50-mm (2-in.), run-of-mine coal in a screw feeder and injected a thick coal slurry into ALH. Initial production rates of 40 t/h (44 stph) through a 200-mm-(8-in.-) diam riser pipeline were achieved with a50-m- (165-ft-) high pilot-scale model. The potential productivity was expected to increase to 100 t/h (110 stph) through modification of the coal injector.

Jan 1, 1995

By Isabel Barton

This article describes and analyzes the history of research into the origins of the uranium-vanadium(-radium) deposits of the Paradox Basin. For several decades after their discovery in 1881, research was desultory and almost entirely descriptive, fluctuating with demand for vanadium and radium. Systematic geologic descriptions, accumulated between 1910 and 1950, supported rapid progress during a government-backed surge of research in the 1950s, when uranium was the chief commodity of interest. Most of the major theoretical innovations date from this decade, including the use of concepts from solution chemistry to identify the conditions and constrain the processes of deposit formation and alteration. Research from this time was highly influential in geology at large, providing the model for sandstone-hosted uranium deposits worldwide and numerous new minerals and mineral structures. After about 1960, mine production remained high but research dwindled, and most new advances were to the details of the hydrothermal model of ore formation rather than its core concepts. By the end of the 1960s, the deposits were understood to have formed at the mixing interface of an oxidized, metal-bearing water with a reducing fluid of debated origin. Research was desultory over the ensuing decades; the source of the metals and the nature of the chemicals constituting the trap were not clearly established. They remain questions today, as do factors like the relationship between ore mineralization and the geologic history of the basin. (More in the full paper.)

Jan 1, 2025

By Daryl L. Gusey, John T. Neubert, Matthew A. Sares

The Colorado Geological Survey completed an inventory of environmental degradation associated with abandoned and inactive mines on National Forest System lands in Colorado. In the course of the inventory, areas with naturally occurring acid rock drainage were also noted. Approximately 18,000 abandoned mine- related features were inventoried, including about 900 features that are considered significant enough environmental problems to warrant further investigation. Water quality data, such as pH and conductivity were gathered at all features where water was present, such as draining adits, seepage at the toe of dumps and tailings, and standing water in shafts. Samples were taken where field tests indicated low pH andlor high conductivity, including several areas with naturally occurring acid rock drainage. Samples were analyzed for dissolved and total metals, and for selected anions. All mine locations and data collected by the field geologists were entered on field forms and, subsequently, into a computer database and GIS format. With the information provided by the inventory, the Forest Service, in cooperation with other agencies, has been able to prioritize abandoned mines for reclamation. In most cases, cleanup is approached on a watershed basis. Mines in priority watersheds have been selected for reclamation first. Watersheds where studies prerequisite to cleanup are occurring include the upper Anirnas River, Willow Creek (tributary to the upper Rio Grande), Chalk Creek (tributary to the upper Arkansas River), the Uncompahgre River, and the Alamosa River. During the inventory, evidence of naturally occurring water quality degradation was found in areas where little or no evidence of mining activity exists. These areas include the upper Alamosa River, the Middle Fork of Mineral Creek, Peekaboo Gulch, and Handcart Gulch. Water from these natural sources has been found to significantly exceed Colorado water quality standards for several metals.

Jan 1, 2000

By John E. Miller

In recent years there has been increasing concern in the mining industry over the availability and high cost of diesel fuel to support mining operations. Unit Rig & Equipment Co. has been deeply involved with the development and testing of the newest designs for trolley assist. Beginning in dune 1980, Unit Rig modified and commissioned six 156 metric ton (170 short ton) trolley assist haulage trucks at two mine locations in South Africa. Operating haulage trucks with General Electric GTA 15E/776 drive systems were chosen for the tests since this size of truck represented the majority of the population of large size haulage trucks and the greatest technical development problems. Test operations have proven the feasibility of equipment designs in actual operation and preliminary economic data has convinced the operators to proceed with planning to modify their entire mining operation to use trolley assist. The initial capital investment incurred for trolley assist can be recovered in a short period of time. Following this quick capital recovery, mines will continue to realize lower operating costs through increased productivity and lower diesel consumption.

Jan 1, 1980

By Jacob Bouke, Jason Janisch, Erik Vlot

The use of conventional tailings deposition methods has been the standard for decades. With the need to reduce the impact of mining, alternative methods are considered when expanding or upgrading tailings handling systems. Converting an existing tailings management system to a more sustainable deposition method during the operation of a mine may incur considerable operational and financial risk, and when assessed more traditionally, does not provide significant advantages. As a result, most mines choose to continue their current technology and add an additional pumping stage or pumpstation to their tailings line in case of a pipeline extension or Tailings Storage Facility (TSF) expansion. This also often involves raising embankments. Changing pumping technology is traditionally assessed by comparing the energy efficiency of current and prospective pumping technology. Despite a reduction in absorbed power, this traditional assessment does not include possible savings in water and the carbon footprint. With the consideration of all these three aspects, alternative pump technologies, such as Positive Displacement (PD) technology, become more economically feasible, providing increased sustainability and enable a site to future-proof their operations. Project feasibility may be affected by the high capital investment required for PD pumps. The benefit of applying PD pumping technology could be enhanced by reducing the volumetric throughput of the pipeline by dewatering the tailings to 65% solids concentration by weight. It was found that despite increasing capital expenditure, the improved reclamation of water will have a positive effect on the direct and indirect cost of fresh water intake to mine operations. This paper seeks to illustrate that in many applications the long-term benefits of investing in sustainable tailings management are optimized when more efficient PD pumping technology is combined with tailings dewatering when upgrading or expanding the tailings handling system.

Feb 1, 2024

Heap leaching has become one of the prime technologies used for the recovery of precious metals from low-grade ores over the past ten years. The recovery process involves mining and stacking the ore on engineered leach pads, with or without crushing and/or agglomeration, followed by leaching with a low concentration sodium cyanide solution. The metal-bearing, pregnant solution is then processed by zinc precipitation or activated carbon absorption to extract the precious metals. The leaching process continues until all economic metal values are removed at which time the spent heap leach pads, the leached materials and excess process solutions require decommissioning. The management of these solutions may present a potential challenge for successful and environmentally sound decommissioning due to their composition, volume or continuity of generation from the spent ore even though active leaching has been terminated. The principal objectives of solution management in decommissioning spent heap leach pads are to meet all operative environmental regulations in a cost-effective manner and to leave the pads in a condition where they do not present a long-term liability either to the operator or to the environment. This involves the reduction in volume of the residual process solutions and/or treatment of these solutions to where they meet applicable water quality criteria. In the past, the environmental and economic aspects of decommissioning and solution management have been overlooked or under-estimated during the planning of mining operations. As a result, there is a potential for long-term liabilities and costs to be recognized only at the end of active leaching, a time at which operating revenues and cash-flow are minimal. Therefore, the decommissioning process requires addressing at the mine planning stage and agencies now require that a plan for solution management after the cessation of operations be submitted prior to initiation of mining. This paper discusses aspects of process solution management during decommissioning, both in terms of quantity and quality, and how potential issues may be recognized and planned for in the initial stages of heap leach design.

Jan 1, 1992