Search Documents

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By E. J. Ostrowski

The history of ironmaking dates back to 4000 BC when an open forge was used to produce a sponge iron from a heap of ore and charcoal. Even at this early date, man recognized the need for a fuel and a reducing agent. As time passed, man developed new methods of producing iron; however, these developments were centered on the mechanical aspects, and as a result, a furnace evolved which is now known as a blast furnace. During this period of evolution,' man struggled with the only fuel he knew - charcoal. Some 5600 years passed before any attempt was made to use coal as a fuel for the blast furnace. The use of coal had its beginning in 1619 when Dud Dudley of England first attempted its use in the blast furnace; as a-fuel and as a reducing agent. Coal charged to the top of the blast furnace was not satisfactory. The volatile matter of the coal choked the flues, and also the poor, strength qualities would not support the weight of the ore. Breaking up of the coal compacted the stock column to an impervious mass. One hundred and sixteen. years later in 1735, Abraham Darby of England introduced coke as the fuel and reducing agent in the blast furnace. The acceptance of coke as a fuel for the blast furnace was not spontaneous. As late as 1870, one-half of the pig iron product of the United States was made with anthracite coal, 30 per cent with raw bituminous coal and coke, and 20 per cent with charcoal. However, by 1910, 96.2 per cent of the blast furnace product was made with coke, 2.4 per cent with anthracite and coke admixture, and 1.4 per cent with charcoal. Coke became the standard fuel in the blast furnace. As the art of ironmaking progressed, more pig iron was produced and more coke was consumed. Coke oven capacity was progressively increased. In 1910, there existed approximately 4,000 coke ovens; in 1960 there was approximately 15,000 ovens. This increase in coke oven capacity was necessary to feed the mammoth appetite of modern blast furnaces.

Jan 1, 1962

The impact of a methane explosion on mining operations cannot be over-emphasized. The explosion is a result of rapid combustion when a methane/air mixture is ignited by an unexpected energy release, such as a mine fire, electrical arc or sparks caused by frictions or rock falls. In most cases, an ignition of methane/air mixture could result in a deflagration other than detonation. Resulting flames and overpressure induced by a methane deflagration will harm neighboring miners and local ventilation control devices.. ,It is essential that the mechanism of an explosion and associated destructiveness be fully understood. This research seeks to predict an influence region of an incident happened within a representative underground mine geometry. The most common geometric changes in an underground coal mine are bends, regulators/doors, obstacle in airways and changes in sectional area. These geometric changes could result in an attenuation of the flame and pressure wave as a result of a methane deflagration. A study of this phenomenon could enable mine planners to have better understanding of the over-pressure redistribution due to the explosion. Both numerical and experimental work has been done in this study to ascertain a better insight of this potentially devastating event. The experimental data are also used to validate the turbulence and combustion models used in this test.

Feb 23, 2014

By S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate as mines are being developed. In this study, finite element method has been used with optimization criteria to design more stable and safe underground openings.

Jan 1, 1993

By C. Pomeroy, J. Weyer, J. Brune

"Mining began in the Erzgebirge (“ore mountains”) region of Saxony, Germany more than 800 years ago, and extensive underground workings cut through the entire area. Some of these old workings are still used today: not for production, but for offering an underground venue for research, tourism and university teaching. One example is the Reiche Zeche mine at the Technische Universität Bergakadamie Freiberg which hosts one of the oldest mining engineering programs in the world. It is imperative to keep all active mine workings well ventilated to make the mine safe for students, visitors and researchers. Since the mine workings at Reiche Zeche are so vast, extensive and, to a large extent unexplored and unmapped, it has been difficult to provide a complete, functioning and adequate mine ventilation model for this mine that accounts for all known and unknown leakage air flows. Researchers at the Colorado School of Mines have cooperation with their colleagues at Freiberg to establish a mine ventilation network model based on a limited number of air readings in known and accessible drifts. In order to balance the measured air quantities, leakage flows were quantified and mapped by comparing input and output flows of mapped drifts, and modelled using Ventsim Visual, a powerful visualization software package. The resulting mine ventilation model is used to locate and quantify the leakage air flows and to examine how much air is lost in each area. With this model, ventilation changes and improvements underground can be documented reflected in the model. This enables the Bergakadamie Freiberg to project air changes required for scientific experiments and to set up mine ventilation in specific areas and for specific needs. The model also enables better ventilation control and monitoring than before. Finally, the model can be used to predict ventilation changes and escape way contamination in case of a fire, ground fall or inundation in the mine. The latter becomes important as the lower mine workings are often flooded during spring runoff, which has created uncertainty about mine ventilation in the past. HISTORICAL BACKGROUND The discovery of silver, lead, zinc, tin and other valuable metal ores in the Erzgebirge region of Saxony, Germany began in the12th century and started a mining boom than lasted for centuries. Surface mines quickly developed underground to access the higher grade veins. Explored by the early geologists and driven by the ingenuity of the miners, the underground works expanded vastly throughout Freiberg and the surrounding region. Development followed the highest grade veins, and engineers developed solutions to drain water and provide limited ventilation to the underground workings. Still, engineered and planned ventilation was usually not a priority in the development of a new drift, which today makes ventilation modeling a significant challenge."

Jan 1, 2015

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semi-variogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe\) at which the semi-variogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn\ component of the same area where the semi-variogram has a nugget effect. The selected length for this case was 4 meters. The Cl fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By M. Niec

Poland lies at the junction of three geologic provinces: the East European Precambrian platform, the Middle European Paleozoic platform, and the Alpine orogenic belt comprising the Carpathian Mountains. However most of the rocks that contain mineral deposits and many of the recently explored and mined deposits are commonly hidden under thick overburden, sometimes up to over 500 m thick. The discovery of these mineral deposits was due to the combination of geologists talents for inference and the keen interpretation of geophysical data ultimately tested by drilling. Examples of such use of the state-of-the-art geology include the following: 1. Sedimentologic and paleogeographic reconstructions led to the discovery of 8.8 Gt of bituminous coal under 500 m of Jurassic and Cretaceous cover in the Lublin basin, 2. Tectonic and paleogeografic data suggested a potential for discovery of burried Upper Permian copper de-posits on the Foresudetic monocline; subsequent exploration discovered 75 Mt of copper and 0,17 Mt of silver, 3. Geological interpretation of gravity and magnetic da-ta combined with sedimentologic data and regional subsur-face geology resulted in the location of 1.3 Gt of Fe-Ti-V ore in the Precambrian basement of northeastern Poland under -500 m of cover 4. A combination of metallogenic theory and geological interpretation of regional geophysical mapping led to the discovery of Caledonian-Hercynian granites and grano-diorites with accompanying porphyry-type Mo-W-Cu ores below 300 m cover on the northeastern border of the Upper Silesian coal basin 5. Tectonic reconstructions based on gravity and seismic data combined with theory on the origin of native sulfur led to the discovery of 1.0 Gt of native sulfur under cover up to 300 m thick. Five deposits were found at the northern margin of the Carpathian Foredeep. The other deposits found include lignite, polyhalite, lead-zinc ores.

Jan 1, 1996

By T. M. Gurr

In response to concerns voiced by local, state, and federal agencies and various environmental groups, the Central Florida Phosphate Industry and various governmental agencies have been investigating methods to accelerate the consolidation of waste clays generated during phosphate washing and beneficiation processes. The objectives of research efforts have been to reduce the storage volumes required for clay waste, accelerate reclamation and to return the land to approximate pre-mining topography. Government and industry research to accelerate waste clay consolidation has evolved two general methods: gravity thickening and chemical flocculation. Gardinier, Inc. one of the phosphate mining companies, evaluated the use of synthetic (polyacrylamide) flocculants as an alternate waste clay thickening method in response to mining conditions encountered at their Fort Meade Mine and the proposed North Hardee County extension of the Fort Meade mine (Figure 1). After considerable research and evaluation, the Alsthom-Atlantic Clariflux Super-flocculation method was chosen by Gardinier, Inc. as a method to seriously consider for use at their Fort Meade mine.

Jan 1, 1986

By Walter R. Lawrence

Newmont Gold Company, formerly Carlin Gold Mining Company, is a publicly owned corporation, 95% owned by Newmont Mining Corporation. Newmont Gold Company has operated gold recovery operations North of Carlin, Nevada, since 1965. Development of the Gold Quarry ore body, 19 kilometers south of the original mine, resulted in the decision to construct gold recovery and ancillary facilities in what is referred to as the Southern Area. Plant No. 2, located 11 kilometers North of Carlin, Nevada, was designed to treat 6350 tonnes per day of oxidized gold bearing ore assaying 2.5 grams per tonne of Au at an average recovery of 87%. Flowsheet development conducted by Newmont personnel resulted in the decision to construct a carbon-in-pulp recovery circuit preceded by two-stage grinding, Detailed engineering was done at Toronto by Bechtel of Canada beginning on January 1, 1984. Actual construction began on March 1, 1984, and was completed in June, 1985. First feed was run on June 22, 1985.

Jan 1, 1987

By J. E. Sepulveda

Tar sand deposits in the. Stare of Utah contain more than 25 billion barrels of in-place bitumen, Although thirty times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion barrels), The term "tar sand" refers to a consolidated mixture of bitumen and sand, Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water extraction process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique., Experimental results indicated that, for a given tar sand sample, percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage, These variables were identified by means of an experimental, factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water extraction process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 1, 1978

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By D. B. Sikka

Porphyry type copper ± molybdenum deposits typically occur in the Phanerozoic rocks and have been well documented. During the past two decades a number of porphyry type Cu ± Mo deposits which range in age from 1055 ± 35 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India, Namibia and Zambia. Kalanjkhand porphyry copper deposit M. P., India which is estimated to contain 789 million tonnes averaging 0. 83 percent Cu (millhead-grade); 0.004 percent Mo; 0.2 gm/t Au; 6 gm/t Ag and a cap of 7.532 million tonnes of oxide are averaging 0.8 percent Cu. The economic potential of the expanded copper mining milling, smelting and refining complex to be built in the future at Kalanjkhand, which is the largest porphyry copper deposit discovered to date in the Precambrian rocks of the world is presented.

Jan 1, 1992

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By E. Lee

The behavior of As bioleaching using Acidithiobacillus thiooxidans (A. thiooxidans) in mine tailings containing highly concentrated As contents (i.e., As=33877 mg/kg) was systematically evaluated according to the changes in temperature (25?40°C, pulp density=0.5%, pH=1.8), pulp density (0.5?4%, temp=30°C, pH=1.8), and initial pH(1.8?2.2, temp=30°C, pulp density=0.5%). The changes in temperature and pulp density affected the As leaching behavior more than the change in initial pH did. Based on the pH and oxidation-reduction potential (ORP) results, the As leaching was attributed to solution acidification. In particular, As leaching was accelerated with increasing sulfate production in the reacting solution. After bioleaching, surface of tailings examined that many pores which dissolved As were formed by a chemical reaction due to bacteria. The As bioleaching efficiency by A. thiooxidans was enhanced by the oxidation of both the added elemental sulfur and the sulfur compounds in the mine tailings. The As bioleaching efficiency was maximized at 50.5% under conditions of an initial pH of 2.2, reaction temperature of 30°C, and pulp density of 0.5%.

Feb 23, 2014

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.