Search Documents

By D. M. Abbott

The requirements of the International Mineral Property Valuation Standards Template (IMVAL Template) (includes Petroleum), 4th edition of April 14, 2021, are based on six principles: 2.1.1 competence, 2.1.2 materiality, 2.1.3 transparency, 2.1.4 objectivity, 2.1.5 independence, and 2.1.6 reasonableness. The IMVAL Template describes “reasonableness” as, “The Valuer must ensure the Reasonableness of the Valuation. Any Valuation, assumptions applied, and any method relied upon should be reasonable within the context of the purpose of the Valuation and the Basis of Value. A method applied to the subject Mineral Property should be within the expected capability and consideration of an assumed likely buyer or lessee of the property.” The IMVAL Template’s Guidance 3.6 on Reasonableness states, “The test of Reasonableness is to consider what appropriately qualified and experienced Valuers, acting reasonably, would conclude in the circumstances. The Valuer must form an opinion that is reasonable in the circumstances, that is, what a Valuer believes is rational and plausible in the circumstances and would be viewed as such if considered by other appropriately qualified and experienced Valuers with the same information and at the same time.” Finally, the IMVAL Template’s Definition 4.26 states Reasonableness “[m]eans that other qualified and experienced Valuers with access to the same information for the same Valuation Date and Basis of Value would consider the Valuer's estimate of Value to be within a reasonable range.”

Mar 2, 2022

By A. Anttila

The grinding mill is probably the most common unit operation used in mineral processing. There is, however, much which can still be done in the way of optimization. This paper discusses the results of a well controlled pilot scale test in which the performance of a tumbling mill with a conventional rubber lining equipped with lifter bars is compared to that with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14 percent more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case the -20 mm ball charge required 26 percent less grinding energy than one with a -30 mm ball charge. The energy savings can. in most cases, be converted to increased capacity. The wear of the grinding media is difficult to assess over a short period test but the results suggest it is somewhat less when a smooth lining is used. The wear of the linings has not been included in this study but it is generally accepted that the use of the magnetic lining reduces the lining costs dramatically. Computer simulation using the Millsoft code, developed by Mishra e.a. confirms and explains the increased effectiveness of comminution when smooth lining and smaller grinding balls are used.

Jan 1, 1998

By E. D. Stephenson

As part of the British Steel Corporation?s development plan during the 1970?s, it was decided to concentrate its bulk steelmaking processes based on the BOS at 4 major Works with access to deepwater ore terminals, for the supply of high-grade imported ores. These 4 sites were at: - 1. Rarenscraig Works in Scotland where the ore terminal would be hilt at Hunterston on the west coast some 50 miles away. Bavenscraig was already an integrated Works but suffered from having to discharge ore 27 Glasgow tenxinus on the River Clyde, which could only accommodate vessels up to 25,000 tonnes. In the future, ore was to be unloaded at Runterston and shipped by a rail-link into Ravenscraig, The new ore terminal would have the potential to unload vessels up to 300,000 tonnes. - 2. Port Talbot Works in south Vales where the existing harbour was developed to discharge large ore carriers. This again was an existing Integrated Works and the benefits of the new harbour also applied to Llanwern Works which was another integrated Works some 50 dies to the east, which would now receive ore from Port Talbot.

Jan 1, 1980

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997

By I. S. Parrish

This article offers one of the infrequent looks at Chinese mining. It includes a brief review by Parrish of a tungsten symposium held there and his comments on and impressions of the mines he visited. In early Oct. 1981, a Symposium on the Geology of Tungsten was held in the Peoples Republic of China. There were approximately 100 participants. Half of them were Chinese. The remainder included representatives of the United Nations, geologists from other nations in Southeast Asia, and 10 invited specialists from other countries. The invited guests included K.F.G. Hosking of the Camborne School of Mines, United Kingdom; C.S. Hutchinson of the University of Malaysia; K. Mattson of LKAB Int. AB, Sweden; T. Kwak of Latrobe University, Australia; K. Sato and S. Ishihara of the Geological Survey of Japan; M. Clarke of the Department of Mineral Resources, Indonesia; P. Bateman of the US Geological Survey; and the author. R. Horsnail of Amax was also invited but was unable to attend because of delayed visa clearance. The meeting was noteworthy because the Chinese were presenting more than half the papers. In addition, following the formal session, everyone was taken to the famed Jiangxi tungsten district and toured four mines there. Organization and Background The idea for a symposium on tungsten geology was brought up in late 1979 during a visit to China by the Economic and Social Commission for Asia and the Pacific (ESCAP) and, in particular, by members of the Regional Mineral Resources Development Centre (RMRDC) of the United Nations. Discussions continued and in the spring of 1981 invitations were sent to selected geologists throughout the world. China's Ministry of Geology handled arrangements, scheduling, and logistics. Travel to China and all correspondence before the symposium were coordinated by the Bandung, Indonesia Bureau of RMRDC. All costs in China were met by the Peoples Republic of China. Airfares and "per diem" enroute for participants were paid by respective governments, sponsors, or individuals. On Oct. 10, visiting participants entered China from Hong Kong. The author and a few others traveled by train to Guangzhou (Canton). Most of the group flew in the next day. The entire group was then taken to Nanchang, traveling by sleeper train and arriving on Oct. 11. The symposium group stayed at the Kiangsi Hotel, where the meetings were held. Meetings Oct. 11 was a day of orientation and rest. The group was taken to an art museum and treated to a Chinese opera movie. The formal meetings began on Monday, Oct. 12. Simultaneous translations aided presentations, though more than half the Chinese speakers delivered their talks in English. The acoustics and sound system were excellent, and the Chinese provided 35-mm and overhead projectors. There was no screen, however, and the yellow, painted wall that was used detracted from projection clarity. In general, the Chinese papers were detailed, thoughtful, and professional. Some, naturally, were stronger than others. Taking them as a unit, one derives the following sequence to the Chinese approach to tungsten exploration: (1) Geologic investigations with mapping at a scale of 1:200,000 accompanied by only minor geochemical or geophysical work. (2) Geophysical investigation with regional gravity and magnetic surveys directed toward identifying deep, tectonic systems and seeking granites in thick, crustal environments. (3) Geochemical sampling in-

Jan 6, 1982

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920's, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By Carl G. Consalus

The Kemmerer Coal Company's Sorensen Mine is located approximately 7 miles Southwest of the Town of Kemmerer, Lincoln County, Wyoming. The coal it produces is delivered via conveyor directly to Utah Power and Light's Naughton Steam Generating Plant. The Plant went on the line in the spring of 1963 and the Sorensen Mine has been producing coal since February of that year. In this period, approximately 2, 000, 000 tons of coal have been delivered to the Plant. Present Sorensen mining operations are being carried out in the upper seams of the Adaville Formation. The formation contains, in some places, up to 30 coal seams of varying quality and thickness. Thirteen seams are considered major and are given numbers; the rest are considered splits off of the major seams and are so named. The lowest seam stratigraphically is the No. 1, or Elkol seam. So far, it has not been committed to power production but is being held in- reserve. It is the thickest seam with 80-90 feet of coal as its average thickness. The other major seams vary from 10-50 feet thick, with most of the seams averaging 17-26 feet of thickness. Each major seam has been opened at least once' to obtain a true gross sample of the coal's performance in the Plant.

Jan 1, 1967

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By B. T. Lusk, J. M. Hoffman, J. Silva Castro

Blast vibration induces sounds within neighboring residences. A housewide vibration and sound monitoring system was installed in a West Virginia home subjected to blasts from various distances and directions. Eighty-nine blast events were monitored and analyzed. Fifteen channels of data were collected, including data from three triaxial geophones, one airblast microphone, one uniaxial geophone mounted on the wall of the house (response channel) and four microphones that recorded CD-quality sound waves inside the house. Each of these channels was recorded on the same time scale. The response channel signal was easily separated into ground vibration and airblast-induced movement, due to differences in the time of arrival. This response channel was then compared to the sounds recorded to determine which component of blast vibration induced the maximum sound response. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast, while for blasts beyond 762 meters (2,500 feet), the maximum sound response was caused by ground vibration without exception. When airblast was identified as the dominant sound generator, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator, the peak amplitude of sound was not related to the amplitude of ground vibration. Findings from frequency analysis showed that the frequency content of sounds inside the house was not related to the frequency content of airblast or ground vibration, regardless of source. This finding suggests that residents will have difficulty determining the source of blast-induced noise in their homes. The proposed airblast response factor (ABRF) can aid blasting operations to determine the dominant source of sounds inside a complainant’s house based on the time-of-arrival relationships. With this site-specific information, public relations responses can be developed accordingly.

Jan 1, 2010

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982

By J. H. Kempton

Refinement of environmental procedures can produce significant cost savings at most mines. Grouting permeable aquifers reduces water pumping and disposal costs. Stable groundwater quality supports reduced groundwater monitoring; and for contaminated groundwater, in-situ or natural restoration should be evaluated. Waste-rock characterization can be minimized using fewer (but more representative) samples, inexpensive surrogate analyses (e.g., NAG instead of humidity cells), and appropriate tests (e.g., avoid meteoric tests on sulfide). Selective waste-rock handling should be compared to random emplacement, which is often cheaper and more stable. Finally, incorporating schedule uncertainty in modeling allows the flexibility to revise mine plans within permits.

Jan 1, 2000

By W. A. Mathews

We report on the progress of an automated mineralogical deportment of fluorine (F) in two portions of the Grasberg District for the development of metallurgical amelioration protocols for Cu sulfide concentrates. Fluorine detection limits in automated SEM technologies range from 1% (TIMA) to about 9% (QEMSCAN), however substitution in hydrophobic minerals or those reporting to concentrate is typically much lower (

Mar 2, 2022

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

The mining industry is an important economical factor in Vietnam. Mining is presently being conducted at about 60 locations and at over 1000 mines. Petroleum extraction and coal mining are the most important parts of industry though metals such as zinc, tin, chromites, iron are also extracted. Last year the sector produced 20 million tons of crude oil, 26 million tons of coal and 500,000 tons of apatite. In particular, Vietnam is one of the world?s largest producers of anthracite, and it is one of the top producers of ilmenite and zircon in the Asia-Pacific region. The government intends to increase the mining production on all levels, however, at present one can observe adverse impacts of the mining activities on the natural environment such as insufficient waste dump rehabilitation, occurrence of acid mine drainage, mining subsidence and emissions as well as lack of appropriate water treatment facilities. This paper describes the current mining situation, future perspectives, the major environmental challenges of the country and approaches to solve these problems. Particular emphasis will be given to the research project ?RAME ? Research Association on Mining and Environment in Vietnam?, a venture carried out by universities, research centres and industry. This project is worked out in collaboration with the national Vietnamese coal and industrial minerals company VINACOMIN.

Jan 1, 2006

By Raj K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Canadian open-pit mines are highly mechanized and use state-of-the-art equipment and support technology. During the past few years, productivity improvements at Canadian open-pit mines have been achieved by taking advantage of larger equipment, in-pit crushing and conveying, truck dispatch systems and electronic management tools. The most recent developments are related to hydraulic transportation and the application of global positioning systems (GPS). Mine planning has become computerized. Environmental issues are dealt with in all phases of planning. Equipment modifications are pursued with vigor to keep the equipment functioning in the hostile Canadian north. In 1997, the mining and mineral processing sector employed 370,000 Canadians, contributing $26.2 billion to Canada's gross domestic product (GDP). The value of production of the Canadian mineral industry, including coal, amounted to $19.1 billion in 1997. Gold remained Canada's leading mineral with production valued at $2.8 billion. This was followed by copper ($2 billion), coal ($1.9 billion), zinc ($1.6 billion) and nickel ($1.9 billion). [ ] Synthetic crude oil from oil-sands mining operations in Alberta represents an important part of Canada's petroleum production. In 1997, the value of synthetic oil production was $2.87 billion. Canadian oil-sands mining has contributed significant technology developments in Canada.

Jan 1, 1999

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017