Search Documents

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are some- times large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy Bureau of Mines- sponsored subsidence study at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County) , West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar re- treat mining. Findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water levels at shallower depths. Post-mining values of hydraulic conductivity were typically somewhat higher than pre-mining values. Changes in water chemistry associated with mining were not sufficient to render the water unfit for human consumption.

Jan 1, 1986

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By Kerry Spickelmier

The only nickel smelter and the only active nickel mine in the United States is Glenbrook Nickel Co., a joint venture (50% each) of Cominco Resources International Ltd. and Cominco Ltd. In 1989, with the nickel price riding high between $2.30 and $2.70/kg ($5 and $6/lb), Glenbrook seized the opportunity to purchase and recommission a southwestern Oregon ferronickel smelter and the adjacent nickel-ore mine. This Douglas County site is only about 97 km (60 miles) due east of the Pacific Ocean, and California's border lies a similar distance to the south. Hanna Mining Co. had closed the operation in 1987. And the following year, the equipment had been largely stripped for salvage value. From November 1990 through August 1992, the mine supplied an average 5 kt/d (5500 wet stpd) of ore. Currently, with import ore supplying 40% of the smelter feed, the mine's daily tonnage averages 4.2 kt (4600 wet st). From November 1990 through August 1993, the mine has delivered 2.1 Mt (2.3 million st) of ore grading 1.22% nickel with an average moisture content of 26%. Buffaloed nickel? A nickel is not worth what it was in 1989 and neither is ferronickel, with recent prices hovering around $1.13/kg ($2.50/lb). To survive, Glenbrook has focused on increasing smelter production to lower its operating costs. And this strategy has triggered several bold moves: • a new, $30 million, port facility and • a 10-year importation contract for ore from New Caledonia, an island approximately 1000 km (625 miles) east of Australia. For a Glenbrook update, a May 25, 1993 visit was made to the company's Oregon operations - the mine and smelter near Riddle plus its new Coos Bay port facility. Unfortunately, as the rain came down that day, so did news of another temporary shutdown. The previous suspension had lasted from Dec. 20, 1992 until Feb. 22, 1993. Barely three months back to work on a wet May afternoon, more than 250 of Glenbrook's approximately 300 employees contemplated yet another shutdown, effective July 31, 1993.

Jan 1, 1993

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

GE Industrial Systems has received a multimillion dollar contract from Bucyrus International to supply complete electrical systems for three new draglines. These machines will be installed at Coal India’s Northern Coalfields’ Dudhichua and Nigahi open cast mines. The Dudhichua and Nigahi mines are located south of Varanasi. They produce Type C and Type E coal for use in the region’s super-thermal power stations. The GE systems will power and control the drag, hoist and swing motions of one Bucyrus W2000 walking dragline at Dudhichua and two a Nigahi.

Jan 1, 2000

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By A. Anani

The need to optimize surface mining operations has led to the use of discrete event simulation (DES) modeling of truck-shovel systems. Often, these models assume truck cycle times are independent and identically distributed (iid) random variables, although, with significant bunching on the haul routes, this may not be valid. The objective of this paper is to present a methodology to (i) account for truck bunching due to slow trucks; and (ii) test for cycle time dependence (i.e. whether truck cycle time data is iid or not). We built a DES model that accounts for bunching due to a slow truck(s) and used the cycle times as data for further analysis. We then tested for cycle time dependence using Pearson correlation coefficients. The results show significant correlation of truck cycle times for different number slow trucks, with variable speeds. Assuming iid in modeling results in over-estimation of productivity and the uncertainty surrounding it. The over-estimation of uncertainty is pronounced when the relative difference in truck speed increases. The confidence interval of the means of truck loads/shift decreases with increasing number of slow operators. This work extends the usefulness of DES in truck-shovel applications.

Feb 27, 2013

By C. Patrick

Longwall face-to-face equipment transfers or moves are, for many companies, the largest single source of non-productive time in a longwall mining system. Detailed planning and resourceful thinking are paramount for economical, safe, and timely longwall moves. New equipment and innovative techniques are frequently tested in order to reduce overall move time. Determining the cost effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed in order to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several innovative ideas.

Jan 1, 1994

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By M. A. Trevits

Mine seals are used in underground coal mines throughout the United States to isolate abandoned mining areas from the active mine workings. The objective of adding inert gas to a sealed mine area is to quickly reduce the oxygen concentration in the sealed area to a level that will not support combustion. In the US, this process is typically conducted from the ground surface and because surface-to-mine access is constrained by so many variables, it is very difficult to provide a source of inert gas to the place where it is needed underground. To alleviate this problem On Site Gas Systems, under a NIOSH contract, built a nitrogen (N2) generation plant that operates in the underground environment. The purpose of this work was to create a reliable in-mine mobile plant that would extract N2 gas from the mine atmosphere and use the gas to create and maintain a safe sealed mine area. The plant is based on a novel design using pressure swing adsorption technology and is sized to fit on a standard shield car or mine dolly for easy transport in and around an underground coal mine. The plant is capable of producing about 900 scf/min of N2 gas at ambient mine conditions. After an exhaustive series of laboratory tests, the plant was field tested at the NIOSH Safety Research Coal Mine (SRCM) where a portion of the mine was sealed and rendered inert. During the test, the movement of the injected gas was monitored at several underground points to observe the progress and extent of the inerting process. This paper describes the plant design and the results of the field test at the SRCM. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By R. L. Brown

The Buchans mining district is located roughly at the center of the island of Newfoundland and contains some 18 separate mineral deposits. The first of these deposits was discovered in 1905, the latest discovery having been made in 1979. To the present (1983), some 16 Mt (17.7 million st) grading 1.33% Cu, 7.5% Pb, 14.5% Zn, 115 g/ t (3.7 oz per ton) Ag, and 1.4 g/t (0.04 oz per ton) Au have been mined. Mining operations are now largely terminated, but a few hundred thousand tons of economically marginal reserves may be mined in a salvage operation. The Geological Association of Canada Special Paper No. 22, "The Buchans Orebodies, 50 years of Mining and Exploration," contains papers which describe the history, geology, and the application of evolving geological concepts in exploration. Papers by Neary, Swanson, and Thurlow and Swanson in that volume are topical to the present discussion. Successful exploration techniques at Buchans included physical prospecting, utilization of the state-of-the-art geophysical techniques, saturation diamond drilling which was made possible by the high gross value of the existing ore, and, since 1955, diamond drilling directed by fairly well understood geological parameters. The record of discovery started in 1905 when the Buchans River deposit was found by Matty Mitchell, a prospector employed by the Anglo- Newfoundland Development Co., a British company which owned mineral rights over a very large area in the Red Indian Lake-Exploits River drainage system.

Jan 1, 1991

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008