Search Documents

By P. C. Fletcher, E. Kaya

The Bond grindability testing procedure has been standardized to measure the same grindability values, i.e. Bond work index (BWi), for the same ore when tests are performed in different laboratories or by different operators. This is accomplished by the standardization of mill dimensions, tumbling speed, grinding ball charge weight and distribution, sample ore charge weight in the mill and operating practice. The results of this investigation reveal that the Bond work index grindability values may differ substantially with different standard Bond ball mills. This paper will review the results.

Jan 1, 2002

By David E. Thompson, Andrew F. McKown, Herbert H. Einstein, Amr S. Azzouz

INTRODUCTION Design of supports for underground chambers in rock has undergone considerable development. This becomes evident when comparing support dimensions of subway station caverns built in the U.S. over the past fifteen years. The Porter Square Station cavern, which is a part of the Massachusetts Bay Transportation Authority (MBTA) Red Line extension, is the latest in this series. It is approximately 168 m (550 ft) long, 21 m (70 ft) wide, and 14 m (45 ft) high, and has a permanent support of light steel ribs imbedded in a 0.4 m nominal (15 in) shotcrete lining. An extensive construction control instrumentation program made it possible to evaluate the performance of the cavern and its support. This evaluation, which is presented in this paper, was the objective of a research project sponsored by the Urban Mass Transportation Administration (UMTA) and jointly conducted by Haley and Aldrich, and MIT. The actually used design procedure was compared with other approaches, notably procedures based on Finite Element analyses and empirical rock mass classification methods. Support dimensions predicted with all these approaches were compared to the actual support and its performance.

Jan 1, 1983

By A. J. Martin, M. J. Peoples, D. J. Adams, A. Opara

"The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium (Se). Nitrogen species are also found in association with coal-mining drainages mainly due to the leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal-mining environments in British Columbia. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains.Treatment to remove Se from coal-mining waste waters has proven to be challenging for conventional water-treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry.This paper's electro-biochemical reactor (EBR) technology provides a controllable and consistent supply of useable electrons to the microbes directly at a low voltage potential (1-3 V) and low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical and robust biotreatment system. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required.Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal-mine waste waters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia’s coal-mining waste waters.IntroductionSelenium in Mining. Selenium (Se) is a naturally occurring trace element, which is an essential nutrient in small amounts (Thompson and Robinson, 1980; Brown and Arthur, 2001). However, it is also toxic to aquatic life, birds, and humans at very low concentrations. A major concern with waterborne Se is the potential for its bioaccumulation in aquatic food chains, resulting in acute and/or chronic toxicity to fish, water birds and amphibians (Besser et al., 1996; Conley et al., 2009)."

Jan 1, 2015

By Colin Lawrence, Michael S. Schultz

Due to the planned deepening of the NY Harbor, NYCEDC/NYCDEP is planning to replace two existing water lines between Brooklyn and Staten Island with one deeper water pipe. The crossing, just north of the Verrazanno Bridge is 1.75 miles long. The new pipeline will be tunneled using gasketed concreted segmented liners. Apressurized face machine will be used through the soft ground. This will be the first subaqueous application using this technology in New York City. This paper discusses the planning, design and risk issues associated with the crossing and the challenging soil conditions that resulted in the decision to use a pressurized face machine.

Jan 1, 2007

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

By Malcolm Ross

Asbestos crystallizes within rock formations undergoing intense deformation characterized by folding, faulting, shearing, and dilation. Some of these conditions have prevailed during formation of the taconite iron ore deposits in the eastern Mesabi Iron Range of Minnesota. This range includes the Peter Mitchell Taconite Mine at Babbitt, Minnesota. The mine pit is over 8 miles long, up to 1 mile wide. Fifty three samples were collected from 30 sites within areas of the pit where faulting, shearing and folding occur and where fibrous minerals might occur. Eight samples from seven collecting sites contain significant amounts of ferroactinolite amphibole that is partially to completely altered to fibrous ferroactinolite. Two samples from two other sites contain ferroactinolite degraded to ropy masses of fibers consisting mostly of ferrian sepiolite as defined by X-ray diffraction and TEM and SEM X-ray spectral analysis. Samples from five other sites contain unaltered amphiboles, however some of these samples also contain a very small number of fiber bundles composed of mixtures of grunerite, ferroactinolite, and ferrian sepiolite. It is proposed that the alteration of the amphiboles was caused by reaction with water-rich acidic fluids that moved through the mine faults and shear zones. The fibrous amphiboles and ferrian sepiolite collected at the Peter Mitchell Mine composes a tiny fraction of one percent of the total rock mass of this taconite deposit; an even a smaller amount of these mineral fragments enter the ambient air during mining and milling. These fibrous minerals thus do not present a significant health hazard to the miners nor to those non-occupationally exposed. No asbestos of any type was found in the mine pit. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Amphibole; Reserve mining; Tailings; Mesabi iron range; Mineral fibers

Jan 1, 2007

Underground mine designs typically try to avoid extraction beneath streams and rivers of any significant size, especially when the overburden rock thickness between the stream bed and the mine is thin. Potential issues with mining beneath streams include excessive groundwater inflow to the mine; weak ground (roof, floor, and pillar) conditions; horizontal stress effects; as well as stream loss and other potential adverse environmental effects. However, there are times when crossing beneath a stream or river is necessary to move into a new area of mineral reserve without creating additional mine access points from the ground surface. Often, stream crossings are completed without thorough assessment, potentially resulting in increased costs, decreased safety, and, in some cases, failure to advance the mine. Selection of the most favorable location(s) to cross the stream must account for numerous factors and the associated assessment often requires a multidisciplinary approach. Stream crossing investigations often require geological, hydrogeological, geotechnical, and geophysical expertise. Phases of stream crossing investigations include desktop evaluation of maps and aerial photography, stream bed observations, drilling, detailed rock core logging, downhole geophysical surveying, hydraulic conductivity testing (packer testing), geotechnical laboratory testing, assessment, and reporting. The deliverables from a stream crossing assessment typically include geological, geotechnical, and hydrogeological characterization of potential stream crossing locations; classification of favorable and unfavorable crossing locations; recommendations for entry design and pillar sizing; and recommendations for if, and how, to conduct pre-grouting activities. Examples of technical aspects of data collection and assessment are provided based on decades of industry experience conducting stream crossing assessments in various underground mining scenarios.

Jul 28, 2020

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal is still a part of energy generation worldwide and has a significant role in the sustainable development of countries. The amount of shallow coal deposits is getting scarce, making efficient underground mining operations crucial for both local and global economies. In underground mining operations, longwall mining is a commonly utilized method to extract deep coal deposits. One of the leading engineering goals in longwall mining is increasing the efficiency of the system by investigating the effects of operational factors on equipment. This paper investigates the shearer performance for a longwall top coal caving operation by discrete event simulation that includes modeling the double-drum shearer, belt conveyors, stage loader, and armored face conveyors (AFC) to evaluate system performance by considering the amount of daily coal production of the shearer. As a result, the most influential factor on mine production is determined and a data-based framework is developed. This study suggests a framework for data collection, data analysis, and the interpretation of the operational data to evaluate the primary production unit’s performance. The models developed for the face coal extraction operations in a longwall top coal caving (LTCC) mine have a bi-directional cutting system and can be implemented in other operations readily.

Jul 2, 2021

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By J. N. Murphy

The use of the National Science Teachers Association (NSTA) regional meetings as a forum to educate teachers on the role of minerals in our society has been immeasurably successful. Each year, on average about 3,500 to 4,000 teachers participate in each of the three regional NSTA meetings. At each of these meetings, nearly 2,000 teachers visit the “Minerals Coalition Booth” and receive free mineral samples and other educational support materials. Some rules of thumb for a successful booth at the NSTA are provided. Considering the level of effort for such a booth, are there alternatives? The NSTA also organizes a national annual meeting with attendance of about 20,000. All who have participated in a regional NSTA agree that the traditional approach of providing a mineral set and teacher materials for a substantial fraction of the 20,000 attendees is not feasible. Conceptual alternatives for minerals education at the national NSTA meeting are introduced and evaluated.

Jan 1, 2001

By Edward O. Reinbold

The paper presents the results of a study which involved collection and analysis of airborne pollutant concentration data in two producing underground room and pillar metal mines which use diesel powered equipment in the area near the face. The results include the concentrations of CO2, CO, NO, NO2 and respirable particulate matter measured with the latest portable instruments, and the carbon and hydrogen contents of the particulate matter samples determined by combusting them in a Elemental Analyzer. The carbon and hydrogen contents are used to estimate the amount of diesel particulate matter in the mine ambient air. The short term grab sample concentration data, although not suitable for determining compliance with ACGIH Threshold Limit Values (TLVs), are related to the TLVs so that they may be compared conveniently. Lognormal frequency distributions and the arithmetic mean of the concentration measurement data are used to compare different mine situations. Conclusions are drawn as to which pollutants are most important to control under actual mine production conditions.

Jan 1, 1979

By R. H. Mullennex

Application of depositional analysis concepts is becoming an ever-increasingly more important and more useable tool in exploration and development of coals in the Appalachian basin. Over the past decade, a rather large number of studies, papers, and publications have addressed various aspects of depositional environments of coals and, to some extent, applications to development. As would be expected as regards a subject so complex as Pennsylvanian sedimentation in the Appalachian basin, certain academic studies have produced conclusions at variance in some aspects to those of other studies. Overall, however, there has been a building- block progression and general refinement with time of understanding of the depositional settings and other factors controlling Appalachian coal distribution, quality, and other minability parameters. Most attempts to explain coal seam characteristics have revolved around a basic deltaic model. Some have attributed certain seam attributes to upper delta plain deposition, other attributes to transitional-lower delta plain settings, and yet others to lower delta plain environments, and so on. While these approaches have provided valuable insight into some general coal characteristics, they are somewhat incomplete and are, in a sense, too broad for specific mine-scale applications. Further, it is apparent that in order for widespread peat accumulation to occur, there must be a drastic decrease in the energy of the depositional system and amount of sediment being brought in, compared to the active deltaic and coastal processes responsible for deposition of the large volume of clastic sediments that dominate the Pennsylvanian system of the Appalachians. Consideration of this fact implies that peats (coals) may not necessarily reflect depositional settings that are directly coincident with those associated with adjacent rocks. Cecil and Englund (1985) address this point, and quite correctly state that "the primary controls on major stages of peat formation are allocyclic processes involving paleoclimate, eustatic changes in sea level, and tectonics." While this statement is inarguable, it does not negate the importance and usefulness of depositional analysis in predicting reserve characteristics that may impact mining and marketability.

Jan 1, 1986

By Steve Kral

MINExpo INTERNATIONL 2000 was a good place for companies to introduce new products, technologies and services to the mining industry. Caterpillar took that a step further. The company hosted a one-day preview of its mining products at its Tinaja Hills Training and Demonstration Center near Tucson, AZ. About 30 members of the trade press spent the day at Tinaja Hills before heading on to Las Vegas for MINExpo INTERNATIONAL 2000. Dozens of Caterpillar professionals provided the editors with a first-hand look at Caterpillar’s mining trucks, loaders, excavators, road graders, water trucks and engines. In addition, these Cat experts explained the intricacies of each piece of equipment, the latest technology that led their improvement and their value to the company’s mining customers.

Jan 1, 2000

By Michael E. Zellars

The distribution of phosphate in Pliocene-Miocene deposits of the Southeastern United States was controlled by the prevailing geologic setting. For each basin a unique set of conditions in terms of relationship of land mass to shelf, depositional environment and seawater composition, and movement controlled phosphate distribution. Concentration sufficient to recognize the deposits as a resource occurred in lagoons or shallow neritic zones, with clastics and carbonates diluting the section basinward. Each deposit within a basin displays similar metallurgy and lithology, notwithstanding post-depositional alteration.

Jan 1, 1978

By R. E. McIvor, Brian Cornish, J. A. Finch, Yue Tan, Claude Gagnon

Fred C. Bond is recognized throughout the mineral processing world as the father of comminution equipment applied science and engineering. The Bond Work Index became a universal standard, and is the most widely used measurement tool for comminution energy consumption. This biography is the story of his lifetime of study, work experiences, experimentation, analyses and findings. His numerous published writings are reviewed. His legacy is one of comminution process engineering that will be used in perpetuity.

Feb 1, 2024

By Donald A. Bruce

Pregrouting is an extremely important part of many rock tunneling projects. However, poor and unsatisfactory performances have been frequently recorded often with very severe consequences, technically and financially. This paper, based on personal knowledge of several relevant case histories, provides recommendations with respect to specification drafting, drilling, water pressure testing, and grouting methodologies, and cementitious grout mix design principles. Even given that the logistical challenges facing tunnel pregrouting from underground will prevent all the sophistication and innovations of contemporary dam foundation grouting being practically implemented, there is still opportunity and need to change “traditional” approaches.

Jan 1, 2005

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.