Search Documents

By D. J. de Clerk

Global trends stipulate the need to optimize existing assets while reducing environmental impacts. This paper illustrates the procedure that was followed to achieve such goals at one of the coal burning flash dryer units at an Anglo American smelter. An in-depth study of the process and related literature led to the development and installation of a revised control philosophy. This system includes modifications to the existing regulatory control structure as well as a hybrid rule-based and model-predictive advanced process control (APC) layer. Since commissioning of the APC, this flash dryer?s average throughput has increased by more than 6%, despite higher feed moistures. Furthermore, even though coal consumption has increased slightly, operating efficiency has improved by close to 5%. This was made possible by improving stability of the drying column outlet temperature by approximately 40%, which in turn enabled selection of a more optimal setpoint. Recent data has shown that APC utilization now exceeds 95%. This is indicative of a successful controller installation with good site acceptance. The same philosophy has therefore since been rolled out to most of the other flash dryers in the group.

Jan 1, 2012

By T. Wallmach

Heavy mineral deposits are a source of the economic important element titanium, which is contained in minerals such as ilmenite, pseudorutile and rutile. In the Ranobe heavy minerals deposit these minerals occur not only as primary unaltered minerals but also display various degrees of alteration resulting in an increased titanium content of the deposit. The presence of the various FeTi-oxide minerals? textural relations is a reflection of geological processes and may ultimately be used to unravel the geological history of the deposit. These minerals have different chemical and physical properties that influence metallurgical tests and the quality of products produced from various mineral beneficiation streams. It is therefore of metallurgical importance that the minerals are well characterized, defined and monitored during preliminary beneficiation tests.

Jan 1, 2007

By W. Wittke, D. Schröder, H. Polczyk

ABSTRACT: The Urft dam, the Diemel dam and the Eder dam are three old masonry damslocated in Germany. The paper describes the rehabilitation measures and the correspondingstability analyses carried out to adjust the dams to today's standards. Remedial works such as theexcavation of inspection galleries, the installation of a grout curtain with a downstream drainagescreen as well as the installation of pre-stressed permanent tendons were carried out. In all threecases the stability of the upgraded dam could be proven on the basis of finite element analyses. ZUSAMMENFASSUNG: Die Urft-, Diemel- und Edertalsperre sind drei alte deutscheSchwergewichtsmauern aus Bruchsteinmauerwerk. Im Beitrag werden Instandsetzungsmaß-nahmen und Standsicherheitsnachweise beschrieben, die erforderlich waren, um die Staumauernan den heutigen Stand der Technik anzupassen. Hierzu wurden Kontrollgänge aufgefahren,Dichtungsschleier mit luftseitiger Dränage sowie vorgespannte Daueranker hergestellt. In allendrei Fällen konnte unter Berücksichtigung der Instandsetzungsmaßnahmen die Standsicherheit derMauer auf der Grundlage von Berechnungen nach der Methode der finiten Elemente nachgewiesenwerden. RÉSUMÉ: Les barrages de Urft, Diemel et Eder sont trois barrages-poids vieux allemandsconstruit de maçonnerie de moellon. Dans cet article, opérations de remise en état et preuves destabilité sont décrits, qui étaient nécessaires pour adapter les barrages à l'état de la techniqueactuelle. À cet effet, des galeries de contrôle étaient creusés, voiles d'étanchéité avec des drains àla face aval et tirants précontraints permanents étaient fabriqués. Dans tous les trois cas, tenantcompte des opérations de remise en état, la stabilité de la barrage pouvait être prouvée à partir decalculs selon la méthode des éléments finis.

Jan 1, 2003

By L. Cortez, Á. Magalhães, F. Durão

Methods based on regionalized variables theory, commonly known as geostatistics, have been widely used since more than three decades to predict/estimate spatial distributed data, namely mineral resources, with quite good results. However, some restrictive theoretical assumptions, such as the need of some kind of stationarity of data and the linearity of the predictor/estimator, are often wrong options in many applications. An alternative approach based on a finite mixture modelling, or cluster weighted modelling (CWM) technique, is presented and compared, in its theoretical and practical aspects, with the geostatistical methodology. CWM is a general non-linear framework based on the estimation of joint density functions allowing the calculation of the conditional probability function of the target values given their locations. Validation tests are performed in a 2D case study, where testing data proceeds from a soil contaminated by a heavy metal. The results of ordinary kriging and CWM estimations show a very good agreement with actual data. Keywords: Non-linear regression, Geostatistics, Ordinary kriging, Finite mixture modelling, Cluster weighted modelling.

Jan 1, 2003

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By E. J. McLean

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

The 8th Annual University of Cape Town (UCT)/ University of Stelenbosch (US) Minerals Processing Symposium was held at the Van Riebeeck Hotel in Gordon's Bay on 3rd August, 1990, under the auspices of the Western Cape Branch of The South African Institute of Mining and Metallurgy. The primary object of this meeting was to give research students at UCT and US the opportunity to present their work to a critical audience from industry, and to obtain feedback regarding the research needs of the minerals industry. Although the emphasis of these symposia is on work in progress at US and UCT, they also create an excellent opportunity for informal discussion between academics and metallurgists in industry. The first symposium in this series was held in 1982 at US, while the symposium in 1989 was replaced by the International Colloquium on Developments in Froth Flotation, also held in Gordon's Bay.

Jan 1, 1990

By M. J. U. T. Van Wijngaarden, A. T. Pieterse

An account is given of the performance of a 37 MVA electric-arc .furnace in which bottom stirring with inert gas by an indirect-contact stirring-plug system was applied. The system, which was developed and patented by Thyssen-Stahl AG, and which is the first inert gas stirring system to be installed in South Africa, was commissioned in January 1992. Initial problems were experienced due to the blockage of stirring plugs by molten steel. The causes of these malfunctions are examined, and an account is given of how they were overcome. The system is described and evaluated. A comparison with direct-contact stirring systems shows why Iscor Vereeniging Works considered it to be more suitable for their Vaal Melt Shop. The results show that, through the successful application qf this technology, Iscor Vereeniging Works has achieved an annual cost saving of more than R2,5 million.

Jan 1, 1994

By L. A. Vermeulen

A simple argument shows that it is impossible for the flight of a rod in contact with a litter bar in a rotary mill to be initiated at that point on the upside of mill rotation when all the forces acting on the rod are in equilibrium. The argument was confirmed experimentally in a study showing that the lift of litter bars is a function of their height, that the rod velocity at the point of departure has a significant radial component, and that the subsequent flight of a rod is along a parabolic trajectory as predicted by elementary mechanics. A quantitative account of the observed effects, which is based on a dynamic theory of the sliding interaction between rods and litter bars, revealed interesting properties of the motions of rods down the surfaces of litter bars when the latter are in uniform circular motion during the rotation of a mill.

Jan 1, 1985

By J. H. van Dalen, P. J. Brandt, F. W. Wessels

A maximum of ten process streams (Merrill barren solutions) can be monitored sequentially with this on-line analyser, and gold concentrations as Iow as 0,005 mg/I can be determined. The design is a further development of the Tell-tale analyser constructed by the Corner House Laboratories during the period 1965-69. The barren solution is preconcentrated automatically by solvent extraction, the solvent being a solution of I per cent Aliquat 336 in di-isobutyl ketone. An aqueous-to-solvent ratio of 40: I is maintained. The extracted gold in the organic phase is determined by flame atomic absorption, each analysis taking approximately II minutes. The long-term reproducibility of the absorbance readings over a 24-hour period of repetitive sampling of four simulated process streams varied from 6,9 to 4,1 per cent relative standard deviation for gold concentrations of 0,0 I to 0,05 mg/I.

Jan 1, 1980

By K. R. Vost

Most theoretical methods for the prediction of air-temperature gradients in underground airways always assume that the temperature of the entering air either remains constant or has only a slow seasonal variation. Large changes of temperature, caused by variations in atmospheric conditions on the surface, were measured in a fourteen-day period in air entering a horizontal airway. The changes in wet-bulb temperature were damped along the airway less uniformly than the dry-bulb changes; significant variations occurred in the wet-bulb temperature of the air leaving the airway. The damping was .associated with large variations in air-temperature gradients. Other causes of rapid changes In temperature are discussed. These changes must be taken into account in predictions of the frequency with which undesirable conditions can be exceeded at critical points in the ventilation circuit of a mine to allow proper planning of ventilation and refrigeration requirements.

Jan 1, 1977

By J. J. C. Heynike

The relationship between population growth and steel consumption since the beginning of the twentieth century is indicated, reference being made to the increasing capacity of production units and the resultant increased pollution in the same area. The need for the control of fugitive emissions with its associated high cost is pointed out. There is a direct relationship between energy and pollution, and examples are given of several improvements that have been made to achieve better energy usage and reduced pollution. Several practical examples of air-pollution control systems are described as applicable to the main metallurgical steel processes of today. In conclusion, reference is made to the fact that, with the improvements attained in reducing pollution, the public will not tolerate a decline in the standards already attained. Environmental control and better energy utilization will continue to be important aspects of steel-plant design and operation.

Jan 1, 1978

By use of a finite-difference model of an experimental galvanic cell, the effect of a resistance in the metalic conduction path on the potential and current distributions in the cell was predicted. The model predictions were compared with experimental measurements of potential profiles (measured by use of a scanning reference electrode) and galvanic currents. The predictions agreed well with the experimental measurements. Apart from this model, which is applicable in macroscopic cells (Le. with an electrolyte of low conductivity), a calculation procedure was developed to predict the effect of an external resistance on the galvanic current in a microscopic cell (high conductivity). The responses of the galvanic currents in the microscopic and macroscopic cells to changes in the external resistance were compared. From the similarity of the responses, a simple practical procedure for the evaluation of the external resistance (meter resistance) that can be tolerated is proposed.

Jan 1, 1989

The Institute has concluded an agreement with the Chamber of Mines whereby the Chamber Librarian maintains a section in the Library for the Institute. Surface effects of underground mining South Africa is blessed with vast mineral resources. It is essential to exploit those reserves if the country is to remain economically viable. Surface-mining equipment The Goldfields Mining Expo '86 is to be held in Kalgoorlie, Western Australia, from 30th October to 1st November, 1986, in conjunction with the Annual Conference of the Western Australian School of Mines. Mintek reports Report M142D Characteristics of gold and pyrite flotation at the Chemwes plant. (1st issued May 1984.) Report M159D Beneficiation tests on andalusite ore from the Marico district. (1st issued Aug. 1984.) Report M164D The recovery of tungsten from South African low-grade schee/ite concentrates. (1st issued Sep. 1984.)

Jan 1, 1986

By D. Francois-Bongarcon

The ?Poisson effect? is defined and characterized. It takes place even when the material to sample is not liberated. Gy, Pitard, Ingamells, and others, including the author, recommend that a minimum average number of particles of mineral of interest characterize the recommended sample size. How many? Recommended numbers range from 6 to 40 particles depending on authors, corresponding to standard deviations of 41% to 16%. Some guidelines are proposed, and the often alleged ?double-Poisson? effect is examined.

Jan 1, 2009

By Sh. Arshadnejad

Stress analysis in a rock medium is essential to determine the stress concentration between two consecutive circular holes and prediction of fracture behaviour. When two consecutive circular holes in a hard rock medium such as granite are loaded internally by the pressure of non-explosive expansion material (NEEM), stress concentration occurs between the holes which then causes the rock to fracture. In this work, finite element (FE) analysis using Phase2 code was employed to study the stress concentration between two consecutive circular holes under internal pressure induced by NEEM. Effects of different hole diameters and spacings, rock properties and NEEM pressures have been analysed. The data gained from the numerical analysis and analytical solutions were then used to develop two models. These models were then modified by using the FE data and polynomial regression analysis. The developed analytical models showed to be in a very good agreement with the FE analysis. Hence, the developed models can be used with confidence to determine stress distribution and concentration factors around two consecutive circular holes in a hard and brittle rock which are loaded internally by the pressure induced from the NEEM. Keywords Finite element method, non-explosive, quarry mining, stress concentration..

Jan 1, 2011

By N. Patel

Many factors, from engineering and design to supply, installation, and operation affect the service lifespan of cast refractory linings. If a shortcoming occurs at any of these stages, the lining lifespan can be drastically reduced. Although not every aspect that can affect a cast refractory lining?s lifespan is outlined here, a few key points are highlighted, with an emphasis on the various installation parameters. Keywords cast linings, refractory lifespan, lining engineering and design, lining supply, lining installation, curing, dry-out.

Aug 1, 2013

By B. Steyn

AngloGold Ashanti?s Obuasi Mine, in Ashanti Province, Ghana, operates a plant utilizing bacterial oxidation technology. The mineralization consists predominately of arsenopyrite with gold associated in the sulphides. The plant was commissioned in 1994, at that time was the largest BIOX® plant in the world, and has been operated by AngloGold Ashanti since 2004. The constraints identified in the plantwere the flotation capacity, BIOX® feed size and disruptions to the BIOX® process. This paper focuses on the practical steps that were followed in order to increase the recovery of the plant. The original plant design was based on a head grade of 10 g/t and an overall recovery of 86.5%. In 2007 the plant was operating at an overall recovery of 79.2% at a head grade of 5.6 g/t and this has improved to 80.6% at a head grade of 5.8 g/t during the last quarter of 2008. Additional improvement to 81.5% are expected by the end of April 2009. Improvements that have been implemented include: ?Replacement of the regrind mill ?Installation of additional float capacity ?Installation of a scavenging circuit ?Installation of a complete water treatment plant. In addition we have focused on the effect of the water circuit on the BIOX® process and the steps involved in correcting this problem. The water circuit was originally designed as an open circuit and through environmental considerations the circuit was closed towards the end of 2007. The bacteria in the BIOX® are particularly sensitive to cyanide and cannot tolerate levels above 0.05ppm (free cyanide), this required extensive modifications to the water circuit. The plant improvement project is ongoing and the current scope of work should be complete by the end of April 2009. Further research and development work is being planned, which includes a ?white rot bacteria? that can consume the preg-robbing carbon and oxidize the sulphide in a single pass.

Jan 1, 2009

By M. Lange

The postulation that primary platinum group metal (PGM) matte will chemically react with magnesia-chrome bricks when temperatures exceed 1500°C was tested. Magnesia-chrome brick samples were heated in contact with matte at 1300°C to 1750°C for 30 minutes, after which the refractory samples were analysed using reflected light microscopy and scanning electron microscopy. The samples were all completely penetrated by matte. As the temperature increased the matte also penetrated the fused aggregate grains and disintegrated them. The chromium concentration of the matte inside the refractory samples was found to be slightly higher than that of the bulk matte. At temperatures of 1500°C and higher, MgO, FeO, and magnesium-rich silicate crystals could be identified in the matte directly adjacent to the refractorymatte interface. Phase relations clearly indicated that chemical reactions take place between primary PGM matte and the magnesiachrome refractory material at temperatures above 1500°C, but that these reactions are more complex than expected from FactSAGE® calculations.

Jan 1, 2014