Search Documents

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By P. J. Foster

This paper summarizes a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialed at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this, a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By F. M. Russell

Scheduling the extraction and rates of production for an underground mining operation is a common task carried out during the life of a mine, from the initial feasibility study through to the final production phase. The scheduling process can be complex when several requirements have to be satisfied, for example, match mill capacity and maximize net present value while constrained by mining sequence and availability of resources. Many mines have computer programs relevant to their operation but because they are site-specific they need considerable reprogramming to be adapted to other operations. Other methods currently in use also suffer drawbacks: manual spreadsheets are laborious, computerized spreadsheets cannot handle sufficient constraints, and operations research techniques require a complex mathematical model to be set up. The use of network analysis techniques has been proposed previously but the unavailability, until recently, of easily used computer programs has not allowed this approach to be developed. There are now many programs which can be used; however, the particular program which has been adapted to mine scheduling is Metier's 'Artemis-PC' running on IBM-XT or compatible machine. The use of network analysis offers many advantages, including the use of a logical mining sequence; activities can be as detailed as required; related activities can be readily incorporated, and costs can be easily extracted. A heuristic approach is necessary to optimize the schedule, but the ease and speed of program execution enables this to be readily achieved, while leaving the mining engineer in full control. The paper discusses the problems encountered in mine scheduling and current solutions. It then details the use of network analysis techniques and the application of the Artemis-PC program to solve mine scheduling problems.

Jan 1, 1987

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By K. -C. Han, S. -Y. Kim

This study was carried out in a bid to survey Ganboke gold mine in Pala, Mayo-Kebbi Province, southwestern Chad. The Ganboke mine is now being prepared for investigation and development, and the research sought to perform rock properties tests of relevant rocks through its geological survey, rock mass evaluation, and in-situ and laboratory tests and analyze the stability by the means of limit equilibrium method, thereby suggest appropriate methods to design the pit slope and individual benches in Ganboke mine. Targenting GS1-GS1' section with the depth of 180 m and GS2-GS2' section with the depth of 150 m in the survey area, we set the height of the bench at 10 m and 15 m, and the angle of bench at 60o and 70o, respectively, and then reviewed the stability for dried condition and saturated condition. The result of examination indicated that it would be appropriate to set the bench height at 10m and the bench angle at 60o in developing the mine slopes concerned. Cette étude est réalisé dans le but de faire des recherches sur Ganboke mine d'or dans Pala, Mayo-Kebbi Provence, Tchad sud-ouest. La Ganboke mine est actuellement en train de étre disposé à la investigation et le développement, et la recherche a cherché à accomplir les tests de la propriétè des roches par l'intermédiaire de la étude géologique, la évaluation de la masse rocheuse, et in-situ et les tests de laboratoire et à faire l'analyse de la stabilité au moyen de la méthode d'équilibre limite, de ce fait à proposer le methodes propres à faire le plan de la pente et les gradins individuels dans la Ganboke mine. Concernant la section de GS1-GS1' avec la profondeur de 180 m et la section de GS2-GS2' avec la profondeur de 150 m dans l'aire d'étude, nous mîmes l'hauteur du gradin à 10 m et 15 m, et l'angle du gradin à 60o and 70o, respectivement, et alors nous avon reconsidéré la stabilité pour la condition sèche et la condition saturé. Le résultat d'examen a indiqué que il pourrait être propre de mettre l'hauteur du gradin à 10m et l'angle du gradin à 60o en développant les pentes de la mine concerné. Diese Forschung wurde um das Gold Bergwerk zu überschauen in Pala, Mayo-Kebbi Provinz, der Südwesten Chad ausgeführen. Das Ganboke Bergwerk ist jetzt zur Erforschung und Entwicklung vorgebereiten worden, und die Forschung suchte zu ausführen die Prüfungen der Felseigenschaft durch geologischen Überblick, Felsmassewertbestimmung, und In-situ und Lavorversuch auf, und analysieren die Stabilität mittelst der Grenzegleichgewichtsmethode, da-durch schlug die angemes-sen Methoden zu entwerfen die Böschungen und die einzelnen Bänke im Ganboke Bergwerk vor. Für den Abschnitt GS1-GS1' mit der Tiefe von 180 m und GS2-GS2' mit der Tiefe von 150 m in der Überblickfläche, wir setzten die Bankhöhe an 10 m und 15 m, und das Bankwinkel an 60o und 70o, beziehungsweise, und dann zurückblickten die Stabilität für die getrockneten Bedingungen und die gesättigten Bedingungen. Das Ergebnis der Untersuchung anzeigte daß es würde angemessen sein zu setzen die Bqnkhöhe an 10m und das Bankwinkel an 60o in der Entwickelungen vom Bergwerk be-teiligt.

Jan 1, 2003

By K. R. Vost

This paper reviews the theoretical methods used in South Africa for the prediction of heat pick-up and air-temperature gradients along main haulages. These methods include those of Starfield, Ramsden, McPherson, and Goch and Patterson. The differences in predictions based on typical airway conditions are explained as being due to differences in the mathematical models on which the predictions are based. The largest discrepancies were found for dry airways and for airways with bulk air coolers. The errors in predictions of the effect of machines and coolers that have been running for only a few months are calculated, and the limitations of various simplified methods are discussed.

Jan 1, 1982

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

[The following notations will be used: O an ore body. z a point in O. z' another point in O. w0 (z) a point support of infinitely small dimensions w0 centred in z. w (z) a sample (or block) of finite dimensions kv centred in z. W (z) a block of size W greater than or equal to w. W'(z) a block of size W' greater than or equal to W. W" (z) a block of size W" greater than or equal to W'. x (z) value of the regionalized variable x with support wO at point z. p (z) average value of x in w (z). pw WZ) = E[x(z')l zt in w(z) pw (z) average value of x in W (z). pwl (z) average value of x in W' (z). pwU (z) average value of x in W" (z). Note that pW (z), pw (z), pwf (z) and pw,, (z) are (regular- ized) regionalized variables with support w, W, W' and W" respectively. The relative sizes of wO, w, W', W" and O are represented schematically in Fig. 7.1. The variance of pw (z) when w (z) takes all possible positions in O is known as the dispersion variance of w in O and is denoted by a? (w in O) or a\: 0; = a2(w in a = Ew,z, inn {[p~ (z) - p121. (7.1) For convenience, the following simpler notation will be used: a> Ew in n [(p w - pl21. Consider now a large block W (z) in O with average value p~(z), and all the possible smaller blocks (or samples) w (z') of size w in W (z). We can calculate the variance of the blocks w (z') in the block W(z), which is the dispersion vaciance of w in W (z), from the relationship a2 [w in W(z)l = Ewcz,, in W(Z) {[PW (z') -pw (z)l21. (7.2) Provided the intrinsic hypothesis is satisfied (§3.4.4), this variance is a function only of the dimensions of the supports w and W, and is independent of the position z of the block W (z). We can therefore define the dispersion variance of w in W, as follows: u2 (win W) = Ew in w [(ptti - PW)~]. (7.3) In cases where the intrinsic hypothesis is not satisfied, the variance of samples w in blocks W may vary only slightly from block to block, so that the average dispersion variance of w in W (z) for all possible W (z) in O can be used: ayw in W) = Ew(,, ~n n {a2 [W in W (z)]}. (7.4) The following example will help to illustrate the importance of the variance of dispersion. Assume that we plan to develop a bedded coal deposit Q. We consider mining the ore body with only one giant dragline, which will extract each day a block of coal of size W'. The total area mined in a year will have a size W". We want to know whether this scheme is acceptable, given that the daily variation in ash content must not exceed a given percentage specified in the sales contract, which is renewable on a yearly basis. On a given day, if we mine the block W' (z), the ash content will average pwT (z). In a period of one year, the expected daily variation in ash content is measured by the expected variance of pwf (z) in W", i.e. by a2 (W'in W"). An alternative mining method might be to use two smaller draglines, each one mining W'/2 of ore per day, and Wn/2 per year. If the draglines are used to mine two distinct sections of the deposit, the expected daily variation in ash content will be u2 (W'/2 in Wj1/2)/2 Other situations, where economic decisions cannot be made without knowledge of the dispersion variance, are illustrated in § 7.4 and 7.5 below. Remark: The notation a2 (w in W) is used in this publication because of its clarity. An alternative notation, which is increasingly accepted in the literature, is s2w/W. ]

Jan 1, 1978

By D. A. Vetter

A novel mathematical model is presented which describes the behaviour of beds of particles, of uniform size and shape but different densities, during autogenous separations. The approach used in the formulation of the dispersion model is a phenomenological one based on a statistical view, which leads to a diffusion-like representation of the autogenous-separation process. Although the model currently considers only density-related phenomena, it accounts quantitatively not only for the density-segregation aspects of the process but for the interactions between the particles. Quantitative predictions of the dispersion model are compared with the results obtained in tests using a specially constructed experimental batch jig, and it is shown that the model provides an adequate quantitative description of the process for particles of uniform size and shape. It is pointed out that, for the description of more complicated autogenous separations, a more rigorous formulation of the particle drag and density-segregation terms will have to be incorporated into the dispersion model. Nonetheless it is concluded that the model as presented in this paper provides not only a novel insight into the mechanisms of autogenous separations but a means by which to analyse similar systems.

Jan 1, 1987

By R. W. O. Kersten

Backfilling is one of the options available to the mining engineer in mine design. The decision as to the type of backfill is dependent on the purpose for which it will be used. For example, in a situation where high-grade, steeply dipping multiple reefs are to be mined, the purpose would be the following: ? to facilitate maximum extraction; a ? to minimize loss of fines; ? to allow closely spaced multiple reefs to be mined; and a ? to create a working platform. The physical properties required which will satisfy the abovementioned requirements can then be defined; the design of the fill plant, as well as the transport of the fill, will be governed by these considerations. The same procedure is also adopted in deciding on backfill in single- reef gold mines. The first question to be asked is the purpose of the fill. It may be to reduce the energy release rate, for environmental reasons, to reduce timber usage, to improve productivity, to reduce stoping costs, to obtain higher mining extraction, and so on. Only after one, or a combination, of these factors has been selected, can the specifications for the fill be decided on, and the plant designed accordingly. The introduction of backfill at Sheba Gold Mine will be used to illustrate the procedure adopted by Anglovaal in determining the type of fill required.

Jan 1, 1988

By S. M. Bradshaw

In order to assess the requirements for online matching when using a transverse electric field (E-field) applicator to treat mineral ores continuously, the effect of varying load properties on matching has been investigated by simulation. The effective permittivity of the ore to be treated is expected to show variation on both short (< 1 s ) and long (minutes) time scales. By modelling the ore as a series of slices with alternating effective permittivity values, it was shown that permittivity variations on the scale of the expected particle size are attenuated significantly and matching is not required. For variations in permittivity on the length scale of the free-space wavelength, variations in reflected power are at most within ±10% of the mean. This is not considered operationally significant, as extreme permittivity variation over this length scale is unlikely, given the expected distribution of ore particle sizes to be treated. At typical ore transport speeds through the applicator, these variations occur on a time scale an order of magnitude shorter than the response time of typical industrial online matching equipment. This implies that online matching is neither required nor possible for short time scale variation. Long-term variations in dielectric properties can be adequately compensated for by current matching technologies. It is concluded that the transverse E-field applicator is robust to changes in the dielectric properties of crushed ores within the expected range of their variation.

Jan 1, 2012

By A. J. Reynolds

In recent years, rapid depletion of the higher grade reserves, allied to decreases in paylimits, has led to the exploitation of secondary, erratically mineralized placer horizons on various marginal and low grade gold mines. On Blyvooruitzicht Mine, the rich Carbon Leader Reef has limited reserves, necessitating exploration of the lower grade Middelvlei Reef. This placer has always presented evaluation and exploration problems, to such an extent that it was, at one stage, considered uneconomic. Despite an extensive underground drilling programme no ore reserve targets of reasonable size were apparent. However, when a certain degree of parallelism between sedimentological trends in the Middelvlei Reef and the underlying Carbon Leader was recognized, a meaningful exploration model could be developed. Firstly, all historical sampling records for the Carbon Leader were entered into a computerized system; the database comprised in excess of 340 000 data points. Variables captured consisted of gold value, uranium value, con- glomerate thickness and total reef thickness. The raw data were then averaged into blocks, and plots of different variables were computer-generated for further analysis. This enabled the Carbon Leader to be modelled sedimentologically and, thereby, exploration targets for the Middelvlei Reef were generated, based on the Carbon Leader facies trends. Geostatistical analysis of sampling data in exposed areas of the Middelvlei Reef underground has confirmed the sedimentological breakdown of the placer into distinct facies areas. A facies model relating value distribution patterns to depositional trends, both for the Carbon Leader and the Middelvlei Reef, has thus been incorporated into a mine planning strategy.

Jan 1, 1987

By M. Pötsch, W. Schubert, A. Goricki

Geological and geotechnical data are essential for the design of tunnels. To determine the rock mass behavior and the support of a planned tunnel excavation a consistent method for rock mass characterization and excavation and support determination has been developed. Probabilistic data processing with analytical methods is used for the quantification of the procedure and allows an evaluation of the applicability and the technical risk of different excavation and support methods. The sensitivity of the procedure on selected input parameters is highlighted in a parametric study. Finally an application of the procedure illustrates the use of the described method of probabilistic excavation and support determination for tunnels. Des données géologiques et géotechniques sont décisives pour la planification d’un tunnel. Pour la détermination du comportement des strates, le choix du soutènement et de la méthode de progression une description compréhensible de la montagne a été développée. À l&apos;aide d&apos;un traitement de données probabiliste, la procédure proposée est transposée quantitative sur une base de méthodes analytiques. De cette manière l&apos;évaluation des méthodes de construction et la détermination du risque technique deviennent possibles. La sensitivité de la procédure de différents paramètres d&apos;entrée est représentée dans une étude de paramètre. Pour finir, l&apos;application de la procédure décrite est montrée à l’aide d&apos;un cas pratique. Geologische und geotechnische Daten sind entscheidend für die Planung von Tunnels. Für die Ermittlung des Gebirgsverhaltens und der Festlegung von Ausbruch und Stützung wurde ein nachvollziehbarer Ablauf der Gebirgsbeschreibung entwickelt. Mit Hilfe von probabilistischer Datenverarbeitung auf Grundlage analytischer Methoden wird die vorgeschlagene Prozedur quantiativ umgesetzt. Dadurch werden die Bewertung von Baumethoden und die Ermittlung des technischen Risikos ermöglicht. Die Sensitivität des Verfahrens von einzelnen Eingangsparametern wird in einer Parameterstudie dargestellt. Abschließend wird anhand eines Beispiels die Anwendung des beschriebenen Verfahrens gezeigt.

Jan 1, 2003

By S. J. Moema, M. G. Maruma, L. A. Mampuru, M. E. Maja

"The most commonly used high-chromium white cast iron (HCWCI) is the hypoeutectic white cast iron that contains 2–3.5 wt.% C and 10–30% Cr. This type of material relies on hard, brittle M7C3 carbides to impart good wear resistance. Due to its good wear resistance, this material has found application in the mining industry and cement industry. However, it has low fracture strength and this challenge led to research aimed at refining the microstructure. This was done by the addition of niobium in the range between 0.1 and 0.6 wt.%. In the as-cast condition, the addition of niobium was found to increase the fracture strength due to the finer eutectic microstructure. The hardness was also found to have increased slightly compared to the reference alloy with no niobium additions. Low fracture strength after heat treatment was observed in the Nb-added HCWCI, which is believed to have been caused by the precipitation of secondary carbides and the transformation of the matrix from austenite to martensitic. IntroductionFor the past few years Mintek has been involved in a project in which a number of alloys have been identified for grinding media applications. The high-chromium white cast iron (HCWCI) alloys were among the alloys researched for this application. The knowledge acquired from the grinding ball media research has now been extended to mill liners, which have traditionally been made of manganese-, chromium- and chrome-molybdenum steels. The replacement of worn mill liners costs the mining industry a significant amount of money and this has led to a need for continuous research to prolong the life of the liners. During milling operations, liner wear has an adverse effect on the capacity of the mill, the energy efficiency and milling efficiency and finally leads to relining, to replace worn liners."

Jan 1, 2016

By F. T. Cawood

Despite economic law and policy instruments with righteous intentions, the politics of resource nationalism could render these instruments unworkable. South Africa is a case in point. After the establishment of democracy, the country&apos;s outdated law and policy framework was replaced with a modern system, and in many respects an exemplary one. Converting the privately-owned mineral right system into a scheme of state custodianship allowed for several resource nationalism instruments, in addition to a resources royalty structure that first, compensates for the loss of a non-renewable resource; second, provides for optimal resource use through encouraging value addition to mineral production; and third, effectively targets economic rents. However, despite these improvements, the country went through a process of fierce debate on whether or not mines should be nationalized: the debate was fuelled by public anger with claims of political non-delivery. The result was considerable noise because of public unawareness of facts and distortion of the facts in political rhetoric. The purpose of this article is, first, to establish the status of resource nationalism in South Africa&apos;s mineral and fiscal frameworks; second, to give an opinion on the findings of the African National Congress&apos;s document on state intervention (Maximising the Developmental Impact of the People&apos;s Mineral Assets: State Intervention in the Minerals Sector (SIMS), 2012); and third, to fruitfully contribute to the fundamental discussion on how South Africans benefit from their mineral riches. The methodology is to start with explaining resource nationalism as an international issue for the extractive industries; then to offer an overview of existing resource nationalism instruments in South Africa-along with their effectiveness in attracting rents and investment. The major finding is that South Africa has resource nationalism firmly ingrained in its current suite of instruments. However, it is necessary to address the perceptions of bad governance, and above all, maintain the stability of the rules governing mineral development in South Africa.

Jan 1, 2013

By M. E. C. Snyman, N. Naudé

"Coal fines produced during processing are difficult to dewater and result in a lower quality product and consequent lower value. A South African coal mine experiences severe difficulties with belt filter dewatering operations due to the presence of fines reporting from the thickener underflows. Plant 2 currently handles super-fine particles of size -34 µm and has low belt filter efficiency: excessive moisture retention lowers the product quality and strains downstream processing. It was necessary to determine an alternative method for dewatering these fines. Blending of fine material with coarser material was proposed as a solution. The effect of coal particle size and layering during ultrafines belt filter dewatering was evaluated using various blends of the fine Plant 2 material with coarser Plant 1 material. The best layering arrangement of the two materials and its optimum blend required to achieve reduced filter cake moisture content was determined in practise using a vacuum filter to simulate belt filtration. A blend of the two materials gave improved dewatering efficiency for the belt filters compared with that of the Plant 2 material alone. The best layering configuration was with Plant 2 material at the bottom and Plant 1 material on top. The optimum blend for industrial applications comprised 48% fines from Plant 2. IntroductionFines are produced during the processing of coal. It is estimated that 2 to 3% of run-ofmine coal reports to the ultrafine portion (-100 µm) (le Roux, 2005). The particle size of coal is inversely proportional to the amount of water adsorption, so smaller particles adsorb more moisture. Moisture removal requires either mechanical processes or thermal drying: mechanical processes are less expensive, but the fines still have high moisture retention. Discarding of fines leads to economic losses, so it is essential that they be dewatered so that they can then be sold as a product: fines need to be treated for both resource management and conservation reasons (Kenney, 1994). Removal of free surface moisture from ultrafine coal particles using a belt filter therefore remains a process that needs to be continuously improved. Ultrafine coal originating from a thickener underflow is known to be difficult to dewater owing to factors such as filter cloth blockage and moisture retention due to clogging. Mixing of finer and coarser materials has been proposed to deliver better dewatering efficiency and improved the quality of the recycled water (Kenney, 1994)."

Mar 1, 2019

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

By R. G. B. Pickering

The Faculty of Engineering at the University of the Witwatersrand and the Mining Technology Division of the CSIR have co-operated to define the problems associated with deep level mining and in this paper they will identify what they consider to be the critical areas requiring technological solutions. This perspective will then be applied to work currently being carried out by both the organizations and gaps for additional developments will be identified. Finally the Co-operative Research Centre methodology operating in Australia is described. The purpose of this CRC is to provide a vehicle for R&D co-operation to develop and implement technologies which will increase the competitiveness of the mining industry. A further objective is to develop an appropriately skilled human resource base.

Jan 1, 1996

By R. Layton

Expert Systems Technology (EST) is becoming more and more widespread in both its range of applications and the public interest. It appears to be capable of performing tasks unmatched by other techniques. Within the mining industry a large body of unsolved problems now appear to have a solution. This paper examines the current state of EST both in the context of the history of Artificial Intelligence and current efforts at building mining expert systems. It provides recommendations for those wishing to get involved, and outlines the problems for those who believe that expert systems are capable of anything and everything. The paper also provides a detailed analysis of limitations of current EST that must direct research into more fundamental, commonsense areas than have been extensively covered before.

Jan 1, 1987