Search Documents

By H. W. J. P. Neomagus, J. R. Bunt, T. S. Mthombo, C. A. Strydom

"Low-cost calcium lignosulphonate (CL), which is a byproduct of the wood pulping industry, was investigated as a potential binder during laboratoryscale pelletization of inertinite-rich high-ash coal fines from the Highveld Coalfield of South Africa. Coal-binder mixtures containing between 1 and 15% calcium lignosulphonate were prepared, pressed, and ultimate, proximate, porosity, XRD, and XRF analyses obtained. It was found that increased pressure during pelletization results in increased attractive forces, due to increased interparticle contact areas. FTIR analysis showed that chemical interactions occur between coal fines and the binder, as evidenced by the formation of new C-O ether-type bonds. The presence of moisture during pelletization enhanced surfactant activity of the binder. Chemical interactions between the coal and the binder seem to be mainly electrostatic, driven by Ca2+ from the calcium lignosulphonate, which may act as a bridge between the anionic parts of the binder and the surface of the coal. IntroductionCoal has over the years remained South Africa’s major energy source, with over 90% of the country’s electricity being produced via coal-fired processes (Arndt et al., 2016). Sasol’s coal conversion technology alone provides more than 40% of South Africa’s liquid fuel requirements (van Dyk, Keyser, and Coertzen, 2006). The production of high-grade coal requires the processing of run-of-mine (ROM) resources by a combination of processes which include crushing, screening, and washing (Radloff, Kirsten, and Anderson, 2003). These processes result in the generation of coal fines (< 0.5 mm) which, until recently, have been discarded into slimes dams (le Roux, Campbell, and Smit, 2012). Several issues are associated with slimes dams, among which are the costs of transportation of these fines from the place of origin to the discard point (often a considerable distance), and the potential environmental effects due to seepage of toxic materials into surrounding ecosystems (Clausen, 1973).Consequently, utilization of these coal fines is an area of great interest. Mechanical densification of fine coal by means of pelletization and/or briquetting to larger sizes for use in technologies that require lump coal, such as chain-grate stokers and fixed-bed gasifiers, has been shown not only to reduce environmental risks (Mangena et al., 2004), but also to significantly reduce storage and transportation costs (Mani et al., 2001). Pelletization is the process by which solid particles are consolidated into uniform, usually hard, impact-resistant agglomerates, rendering them useful as a fuel with sufficient calorific value for domestic and industrial utilization (Finney, Sharifi, and Swithenbank, 2009)."

Dec 1, 2018

By Y. Sagawa

The Hishikari Gold Mine consists of epithermal vein type Au-Ag deposits, each of which has several veins standing almost in parallel each other and inclining 70 to 90 degrees. The veins have 1 to 3m widths and are extracted mainly by drifting and bench stoping with waste rock fill. The Hishikari has tried to optimise the stope dimensions by the Potvin’s Stability Graph Method, which is well known as an easy and effective tool to design appropriate stope dimensions. The method, however, has some limitations of application due to its simplicity so that it has been used only in limited cases. The authors developed a new numerical approach, based on 2D FEM solu-tion for the stability analysis. As a result, it has been possible to solve the Hishikari situation. The authors also introduce the concept of the design approach and compare the results obtained by us-ing the approach with the database of the Stability Graph Method for validation. La mine d’or Hishikari se compose de gisements d&apos;Au-AG avec des types de filons épither-maux dont chacun a plusieurs veines qui sont presque parallèle les unes par rapport aux autres et sont inclinées de 70 à 90 degrés. Les veines ont de 1 à 3 m de largueur et elles sont principalement extraites en creusant et en abattant des bancs de roches encaissantes. Hishikari a essayé d’optimiser les dimensions du chantier d’exploitation avec la méthode de graphique de stabilité de Potvin, bien connue comme un outil facile et efficace pour avoir des dimensions de chantier d’exploitation appropriées. Toutefois, la méthode a certaines limites d’application dues à sa sim-plicité de sorte qu’elle a été utilisée seulement dans des cas limités. Les auteurs ont développé une nouvelle approche numérique, basée sur la solution 2D FEM, pour l’analyse de stabilité. Par conséquent, il a été possible d&apos;expliquer la situation de Hishikari. Les auteurs présentent le concept de l&apos;approche et ils comparent les résultats donnés en l&apos;employant avec la base de données de la méthode de graphique de stabilité pour la validation. Die Hishikari-Goldmine besteht aus Au-Ag-Ablagerungen mit epithermalen Adern, die jeweils mehrere Adern aufweisen, die mit einer Neigung zwischen 70 und 90 Grad nahezu parallel zueinander verlaufen. Die Adern haben eine Breite von 1 bis 3 Metern und werden überwiegend durch Vortrieb von Stollen und Bergversatz abgebaut. Hishikari hat versucht, die Abmessungen des Abbauorts durch das Potvins Stabilitätskurvenverfahren zu optimieren, das als einfaches und effizientes Mittel für die Erzielung angemessener Abmessungen des Abbauorts bekannt ist. Das Verfahren weist jedoch aufgrund seiner Einfachheit einige Anwendungsbeschränkungen auf, so dass es nur in einigen Fällen benutzt worden ist. Vor diesem Hintergrund haben die Autoren einen neuen numerischen Ansatz entwickelt, der hinsichtlich der Stabilitätsanalyse auf der 2D-FEM-Lösung beruht. Dadurch wurde es möglich, das Problem von Hishikari zu lösen. In diesem Dokument stellen die Autoren die Grundlagen des Ansatzes vor und vergleichen die erzielten Resultate durch Benutzung der Datenbank des Stabilitätskurvenverfahrens zur Validierung.

Jan 1, 2003

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

P.W.D. ROSTER OF CONSULTING ENGINEERS (Extract from a letter from the Secretary for Public Works) In recent years a large number of professional engineers has entered the consulting field. Although the names of most of these have been placed on the Department&apos;s roster of consulting engineers either as a result of representations made by the South African Association of Consulting Engineers or by applying direct to the Department there are still some who seem to think that canvassing through an influential person is necessary to obtain commissions from the Department. The Department&apos;s roster is open to all registered professional engineers who are suitably experienced to undertake consulting work and commissions are awarded strictly on merit. I shall appreciate it, therefore, if registered professional engineers who wish to be considered for commissions by the Department could be advised that they must apply, in the first instance, to be placed on the Department&apos;s roster. On receipt of such an application a questionnaire listing all the information required by the Department will be forwarded to the applicants for completion and returning to the Department for record purposes. All names which appear on the roster are taken into account when a commission has to be awarded, due consideration being given to factors such as geographical position, seniority, capability and compatibility. AMERICAN SOCIETY OF MINING ENGINEERS 1970 FALL MEETING AND EXHIBIT The Secretary for Commerce has passed to us a letter received from the American Society of Mining Engineers, reading as follows: "We would be delighted to have South Africa attend our meeting next year and to exhibit some of their mining equipment in our Technological Information Exchange. The 1970 SME Fall Meeting and Exhibit will be held in St. Louis, Mo., October 21-23, 1970, at the Kiel Auditorium. The AIME WorId Conference on Lead & Zinc Mining and Metallurgy will be an integral part of our meeting-and an added incentive to attend. It should be understood that we discourage the showing of actual mining equipment and encourage the manufacturers and suppliers to send their engineers to man the booths. We hope that the exhibits will endeavour to put across their story by means of photographs, drawings, models and literature, rather than by display of prototypes of the actual equipment. We will be happy to welcome manufacturerers from South Africa as well as the mining engineers who, from time to time, have registered at our meetings." For further particulars, interested parties may write to the Society of Mining Engineers, 345 East 47th Street, New York, N.Y. 10077, D.S.A.

By M. Tang, X. Tong

"SynopsisSlime coating is one of the most common ways for serpentines to contaminate metallic mineral concentrates during traditional flotation of coarse sulphide particles. This could pose quite a complicated and challenging problem in the case of some types of low-grade and finely disseminated Cu-Ni ores bearing high serpentine contents. This is the case for the copper and nickel sulphides from the Yunnan Mine, China. Previous batch flotation tests of this ore resulted in satisfactory recoveries of 86.92% Cu, 54.92% Ni, and 74.73% Pt+Pd, and concentrate grades of 4.02% Cu, 3.24% Ni, and 76.61 g/t Pt+Pd. However, the MgO content in these concentrates was more than 19%. In the current study, microflotation tests and settling rate tests were introduced to investigate the effects of a combination of strong collectors (a 2:1 weight ratio of butyl xanthate and butyl ammonium dithophosphate) on entrainment of serpentines in metallic mineral concentrate, as well as visual observations of the concentrates in suspension using still photography. All test results indicated the presence of serpentines entrapped in the hydrophobic flocs that resulted from these collectors, even with the use of effective gangue depressants. These strong collectors are used to flocculate the ultra-fine sulphides by forming loose and ‘fluffy’ hydrophobic flocs. However, these hydrophobic flocs may also be able to load or entrap some serpentine slimes into the concentrate, and this entrained serpentine could be harder to remove by using depressants or intensified conditioning than serpentine slime coating on the particle surfaces.IntroductionSerpentine minerals, which have the generalized composition (Mg,Fe)3Si2O5(OH)4, can be easy to crush and grind due to their convoluted and bent layered structures. These serpentines can hinder the enrichment of some metallic minerals and dilute their concentrates by entrainment during flotation. The resulting high pulp viscosities, slime coatings, and high content of dissolved ions adversely affect the flotation recoveries of copper and nickel sulphides, and high levels of MgO entrained in the concentrates lead to heavy penalties from smelters. Since the quality of nickel flotation concentrate depends heavily on its MgO content (generally less than 6–7% for No.1 or 2 grade nickel concentrate according to the standard requirement from National Nonferrous Industry), reducing the entrainment of serpentine during flotation is becoming more and more pressing. Previous research has focused on the collectors and depressants that are commonly used in copper-nickel flotation, as well as their interaction mechanisms."

Jan 1, 2015

By D. Borman

The location of underground positions in mines has usually fallen to their survey department&apos;s. Their usual tasks include: ? installation of a high-precision peg network like the National Survey grid as beacons ? offset measurements to the sidewalls, and sometimes hangingwall and footwalls, of development tunnels and excavations ? offsetting of stoping panels for the calculation of face ? advance and the square meterage of area removed. Other departments build their observations into the plans produced by the surveyors. If more precision is required, they ask the surveyors to `elevate&apos; their points with a theodolite. Apart from the survey peg network and `elevations&apos; these measurements are usually planer measurements suitable for producing plans, sections and projection sheets. When the only representation medium was a sheet of paper or transparency, this was perfectly suitable. However the development of CAD models of the workings has changed all this. Full 3D representation is not properly catered for in the tool sets in current use, and needless hours are spent converting analogue-type observations into digital form. The basic survey models need to be augmented by the observations of other disciplines that are also required to locate positions underground. These include: ? the need for geologists to plott their mapping and ? borehole logs into 3D space ? the need for samplers to position their sample points accurately because the geostatistical models are biased and inaccurate ? the need for stoping width recorders to position their thickness observations to prevent errant evaluation and bonuses ? the need for rock engineers to place their mappings into 3D to build true geotechnical models to manage geotechnical stresses ? the need for production officials to receive updated face ? positions during the month so that they can manage the ? production and utilize their resources properly. This paper covers a new method of positioning profiling points to a suitable degree of accuracy. I believe the method is sufficiently simple and cheap for all to use. Historical methods Platinum and gold orebodies, especially in South Africa, are generally narrow tabular deposits. This made them suitable for depicting on a 2D medium like paper. The determination of stoping or face widths was not a problem, as the ore is removed in a single stoping process. Such 2D representations could be easily positioned using tape offsetting between survey pegs or points tied in from survey pegs. Problems of dip were handled by using &apos;Stope Sheets&apos; which chose a best fit projection for the whole area depicted or by using true dip section sheets for inclined tunnels. Rolling reef and potholes were the common areas of difficulty. Most mines now model their orebody and plan the extraction in computer graphics. This means that the representation of the current workings has to change to support this trend. It now becomes a truly 3D problem. Mining officials find it inconvenient to have their actual workings in single-line depictions while their orebody is depicted with top and bottom contacts and the planned tunnels in 3D shapes. Geological models which form the basis for the resource model and planning process are often out of date, as the updating process is slow. The geological mapping has to be plotted onto sections and plans. These are then digitized into graphics by a draughtsman and checked by the geologist. Only then does the interpretation and model update take place. Potential methods to create 3D &apos;Actuals&apos; Global positioning systems (GPS) Surface mines have been blessed by the advent of GPS technology. These simple-to-operate pieces of equipment and compatible software make it possible for all types of mine employees to locate themselves, and therefore to locate their observations. GPS are often inexpensive and give an acceptable degree of accuracy. Only in deep pits or close to the highwalls are observations hindered. Such technology cannot however, work underground. Ground penetrating radar (GPR) GPR is reported to be very useful for estimating the positions of potholes and faults. However it is still considered as providing an estimate, not a definite measurement. GPR is good for seeing into solid rock, not into open spaces. Inertia reading devices Experiments with inertia reading devices have been conducted on the mines. They were the forerunners of GPS for military guidance systems, and were even used for city navigation in the early 70s. They do however work best with heavy or fast-spinning gyros. Anglogold Ashanti&apos;s attempt to use them were discontinued in the mid-90s when the developers asked for an additional few million rand for a device that would weigh more than 12 kg and have a limited operational life.

Jan 1, 2006

By Y. Mitani, M. Zhang, M. Takeda, T. Esaki

Despite their inadequacy, assumptions of isotropy and homogeneity are often applied to the analyses of in situ permeability tests. In this paper, we exam the effects of anisotropy and heterogeneity on Pressure Pulse Test (PPT) and Constant Head Injection Test (CHIT) by means of numerical approaches. Some new findings that offer practical considerations in properly interpreting in-situ permeability tests are presented. Malgré leur manque de précision inhérente, les assomptions d&apos;anisotropie et d&apos;hétérogénéité sont souvent utilisées lors de test de perméabilité in situ. Dans cette étude, nous examinons les effets de l&apos;anisotropie et de l&apos;hétérogénéité sur le test par pression pulsée et le test à injection à charge hydraulique constante par le biais de la simulation numérique. Des nouveaux résultats permettant une interprétation pratique et claire des test de perméabilité in-situ sont présentés. Trotz ihrer inhärenten Ungeeignetheit werden häufig Annahmen über Isotropie und Homogenität auf Analysen von in-situ Permeabilitätstests angewendet. In diesem Papier untersuchen wir die Effekte von Anisotropie und Heterogenität auf Durck-Impuls-Test (PPT) und Konstant-Kopf-Einspritztest (CHIT) mit numerischen Ansätzen. Einige neue Befunde, die zu praktischen Erwägungen zur richtigen Interpretation von in-situ Permeabilitätstests führen, werden vorgestellt.

Jan 1, 2003

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, P. M. Van Den Heever

Some of the important properties of solid electrolytes that influence the performance of electrochemical oxygen probes are discussed in the first part of this paper. It is shown that accurate and reproducible measurements of oxygen in liquid steel are possible with commercial oxygen probes only if great care is exercised in the make-up of the chemical and phase composition, as well as the microstructure of the solid electrolytes used in these probes. To prove this premise, the second part of this study reports on the results of an experimental evaluation of new commercially available oxygen probe. An evaluation of the solid electrolytes used in this probe indicated that the consistency of the chemical composition, degree of stabilization, and microstructure of the electrolytes used are well controlled. The successful application of this particular oxygen probe under industrial conditions was confirmed. It was also found possible to make reliable and reproducible measurements, with acceptable uncertainty, by proper handling of the probe. Some recommendations are made as to the interpretation of the e.m.f. response curve and the use of the electronic processing unit supplied with the probe.

Jan 1, 1987

By D. Limpitlaw

Industrial mining in Zambia started in the 1930s when the world class copper deposits near the border with Katanga were developed. The discovery of these deposits began at the turn of the century when the first claims in the Copperbelt were pegged at Chambishi, north of what became the town of Kitwe1. World War I and the difficulties of raising sufficient capital for such large scale undertakings delayed the exploitation of these deposits. Following this hesitant start, a large copper mining complex was built, resulting in the development of five major towns, all highly dependent on the mining and beneficiation of copper and cobalt. Copper became so important to the country that, on independence, the only non-mining town to make it onto a list of the top six was the capital, Lusaka. From commissioning of the mines to the end of the colonial period in 1964, copper production increased to just over 640 000 t annually2 (see Figure 1). After the establishment of the new Zambian state, production continued to increase, supported by a benign legislative environment and strong international copper prices. The government of Kenneth Kaunda was intent on improving the conditions of the rural poor and reducing unemployment in urban areas. To this end, the government embarked on an ambitious project of refocusing Zambia&apos;s economy away from the colonial role of commodity supply to one of decentralized mass employment. The Copperbelt industrial complex was key to the success of this approach, and in 1969 the Zambian State acquired a 51 per cent stake in Zambia&apos;s two main copper producing companies: Roan Selection Trust and Rhodesian Anglo American Corporation. The former became Roan Consolidated Mines Ltd (RCM) and the latter became Nchanga Consolidated Copper Mines Ltd (NCCM). In the year they were nationalized, the mines produced at least 720 000 t of copper? and employed approximately 48,000 workers (see Figure 2)2-4. The subsequent economic policies of the Zambian Government depended heavily on the state&apos;s ability to monopolize the proceeds of copper mining.

Jan 1, 2011

Colloquium and General Meeting were held at Kelvin House on 19th May, 1971, the theme being &apos;Modern trends in coal mining practice.&apos; Mr V. C. Robinson (President) was in the Chair. The Colloquium was attended by 205 delegates and was opened by the President at 9 a.m. OBITUARY The President: &apos;It is my sad duty to announce the death of C. C. Cullen, Fellow, who joined the Institute in 1946 and passed away on 15th March, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence&apos;. ELECTION OF SCRUTINEERS The President: &apos;In terms of Clause 9.4 of the By-Laws I now call for the nomination of seven Corporate Members to act as scrutineers of the ballot for Council&apos;. Messrs V. C. Robinson, Prof D. D. Howat, Dr J P Hugo, D. G. Maxwell, J. K. E. Douglas, R. J. Adamson and P. Lambooy were nominated by P. W. J. van Rensburg and seconded by P. A. von Wietligh. The President: &apos;Are there any further nominations? If not I declare these gentlemen elected.&apos; MEMBERSHIP The President: &apos;I have much pleasure in announcing that the names of candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Douglas Edward King, Bryan Rudolph Scott, James Gregor Phimister, Anthony David Walters. Graduates: Cornelius Johann Muller, Marthinus Stephanus Mulder. Associates: John George Everson, Colin Robert Llewellyn Davies. Students: Francois George Enslin Beetge, Ewald Boshoff, Christiaan J. Cloete, Christopher John Davies, Cameron George Elvin, Kenneth Eric Field, Johannes Louis Fourie, Hans Gert Gastrow, Peter John Ledger, James Robert William Lindsay, Kynaston Lloyd McDonald, Richard Peter Mohring, Arthur Leslie Painting, Matthias Arthur Pascall, Ian Neil Sinclair, Donald Allan James Ross-Watt. MEMBERS TRANSFERRED TO A HIGHER GRADE From Member to Fellow: Peter Norman Roberts. From Associate to Graduate: Alfred Eric WaIter Fletcher. From Student to Graduate: Wilfried Pierre de Villiers, Edward Emile Eichenberger, William Alan Nairn, Lodewyk Johannes de Jager, Colin Henry Obray, John Grenig Rees. COLLOQUIUM The President opened the proceedings and introduced Mr N. W. S. Schumann as the overall chairman for the day. The following papers and contributions were presented: FIRST SESSION: Chairman R. C. J. GOODE. Paper: &apos;Problems encountered in the operation of a new colliery&apos; by P. M. C. Wilson and A. A. Oakes. Contributors: D. J. Moloney, G. R. Canny, I. G. Evans, R. B. MacGillivray, Dr F. G. J. de Jager, M. J. Deats, and N. Zolezzi. R. B. MacGillivray Mr President and gentlemen, I would like to congratulate the authors on presenting a most interesting paper on a very important subject. After several attempts at finding suitable reserves to extend the life of Welgedacht Exploration Company&apos;s Utrecht Colliery a block of coal rights was acquired south west of the town of Utrecht. A study of these reserves showed that they would enable a satisfactory return on capital invested to be achieved. It was decided therefore to open up what is now called the Zimbutu section of Welgedacht Exploration Company, to produce 41 000 metric tons of coal per month. The decision to open this section was taken in August, 1968 and due to certain allocation requirements it was necessary to bring it into production by the 1st of January, 1970. Fortunately a fair amount of statistical data had been collected prior to August, 1968 from the old Utrecht Colliery in anticipation of opening a mine and a fairly detailed rechnical report had been prepared. As a result the dead line was only missed by four days. Main features of the Design A feasibility study was carried out on three possible shaft positions and the final position was selected from these three on economic grounds. As the coal seam at the selected shaft position was only 21 metres below the surface it was decided to sink two twin incline shafts to enable rapid establishment of through ventilation and alternative hauling arrangements for quick development. This also allowed the final vertical ventilation shaft to be placed at some distance away to avoid the nuisance of fan noise. Second outlet requirements are also very well met by these twin inclines. Again on the basis of economics and also due to the uncertainty of roof conditions it was decided to use hand loading methods underground. However, to allow for future possible conversion to mechanised loading, should this become economical through rising wages, a conveyor belt was installed in the hauling shaft. This conveyor belt is fed from an endless rope haulage in the east companion by means of tipplers, a bin and a feeder. The main development heading was left clear for the future installation of a conveyor belt which would afford easy conversion to mechanisation.

By Mark Craddock, Johan Swanepoel

In this paper we present The Ultimate Flotation Cell, a newly developed flotation cell that is proving very popular in the industry. All flotation cells have only one purpose and that is the recovery of the required product, the patented impeller and disperser system of the Ultimate Flotation Cell allows total flexibility in order to achieve the optimal recovery. This ability to tune the cell performance provides the optimization of the ?capture? (collection) stage, all existing models address the need for a wide bubble size distribution (100µm-2 mm) to obtain a better flotation size-by-size, Yoon, 1999,Yoon 2000, Franzidis and Manlapig, 1999. The Ultimate Flotation Cell provides flexible performance optimization. This ability to optimize the flotation regime particular to a specific ore is achieved by the following factors: ? The impeller allows vastly improved air induction rates compared to conventional and sparged cells. This ability to induce and disperse large quantities of air, in a controlled manner, allows the cells to be tuned to give the optimal Sb by varying the rotational speed via a VSD which every cell is fitted with. ? The patented impeller gives a very constant and stable air induction rate, which ensures that the cell?s circulation pattern is constant, giving a very stable surface, allowing optimal froth depth. ? Although conventional dart valve, level control can be offered, great success has been achieved with a simple draft tube/sand relief device. ? The cells have a inlet design similar to the old Denver ?Cell-to-Cell? design, which guarantees the at lease one pass through the mixing zone in each cell. Actual plant performance data will be presented from two plants, one in Zambia and the other in the DRC.

Jan 1, 2007

By G. A. Wiebols, N. G. W. Cook, N. C. Joughin

Discussion R. E. Rarnes (Member): The original concepts and the pioneering work now brought to the practical test stage by the Mining Research Laboratory team deserve our highest praise. The authors of this comprehensive paper rightly stress the urgency of establishing the extent to which the apparent potential can profitably be realised in practice. It is to be hoped that adequate funds will be made available by individual mining companies, the Chamber of Mines and manufacturers to attract the necessary staff and maintain the high rate of achievement of the last two years. From the Seventy-Eighth Annual Report of the Chamber of Mines and its members we see that, in 1967, with a Working Revenue of R759.8 million from gold and R54.6 million pit mouth coal sales and with profits from gold and uranium and pyrite of R307.9 million, only R1.9 million was spent by the Chamber on all forms of Research. It is considered unlikely that the associated mining companies and manufacturers exceeded this investment expenditure. Assuming a total of R4 million spent by the industry on Research and Development, this is less than half of 1 per cent of sales of gold and coal. This percentage, so low in comparison to North America and Europe, is no worse than that of Exploration expenditure which, in 1967, with South Africa&apos;s total mineral production of R1,287 million, was estimated to have been R6 million (Pretorius 1968). In a primary industry with ever present depletion of ore deposits and with cost escalation, expenditure on Exploration and on Research and Development is not a risky luxury but a tactical obligation. The potential rate of return on research expenditure into rock breaking is high. Stores consumed by gold and coal mines, members of the Chamber of Mines, totalled R316.2 million in 1967. Except for purchased power costing R42.2 million the highest cost group was explosives, drills and drill steel totalling R33.8 million or 10.7 per cent of the total stores consumed. In the paper under discussion it is claimed that the low &apos;effective stoping width&apos; should greatly reduce the likelihood of rock falls or rock bursts to the extent that permanent support can be dispensed with. Insofar as this narrow cut is only 12 in. in advance of the working area which, with a 10 in. channel, is unlikely to be much reduced in width from that achieved by current methods, this claim is not readily understandable. Were it to have been based upon the regional support gained from packed waste it would have been more acceptable. Pre-developed stope drives may give serious trouble at depth and for this reason it is questioned whether a stoping area can avoid periodic sub-development blasting-the spoil and fumes from which will interfere with the rock flow and continuous mining of the rock-cutter. If, in the mining method proposed by the authors, stope drives are cut as small as possible (6 ft by 6 ft) then 25 per cent of the total tons handled (excluding resued waste) and 5 per cent of the gold will be blasted conventionally in the stope. At this stage one cannot envisage tunnelling machines economically or practically capable of such work. The various methods described by the authors and subsequent contributors for breaking waste are most interesting. It was noted that the &apos;bull wedge&apos; and &apos;explosives&apos; in Fig. 1 of the paper were no further from the ideal point &apos;A&apos; than was &apos;cutting&apos;. The writer considers that the bold and imaginative steps taken by the Mining Research Laboratory Team, the mining companies and the manufacturers concerned will eventually lead to a successful rock cutting machine with universal application largely independent of rock type. This may take many years. In the meantime other methods of improving productivity of saleable metal by rock breaking teams should be investigated even if such methods have local applications only. In 1955 the writer conducted tests with a wire saw similar to those used in quarries in the Northern Transvaal and elsewhere. Jeppestown shale, the immediate footwall of much of the East Rand gold field, was cut at the rate of 6 in. per hour using sand, water and a special endless rope driven by a low h.p. motor. A hypothesis on its application was submitted to the Office of the Government Mining Engineer in 1955 and to other mining institutions in 1966 after the writer returned to South Africa. By inference, rope sawing was classed as less promising than other methods tested in the Orange Free State Goldfields (Parker 1969). With highly resilicified hanging and footwall quartzites this was not surprising and confirmed the writers findings when testing hanging wall quartzite from the East Rand in 1955. The relatively uniform conditions, the low strength, hardness, and silica content of the Merensky Reef platinum deposits (Gray and von Bardeleben 1969) and in particular, the existence of overlying Merensky pyroxenite (Cousins 1964) make this and the East Rand attractive areas for larger scale testing of wire saws. It is envisaged that in suitable rock types the 5/8 in. slot would be advanced down dip or down a minor dip. In undisturbed areas &apos;faces&apos; of up to 200 ft in length could be cut several feet in advance of breaking which could then consist of light blasting to the second free face or some of the methods now being tested for breaking waste in rock-cutting operations. A wire saw is an inexpensive and simple machine which, in some areas, could make significant and early gains in rock breaking efficiency as well as in ground and stoping width control.

Jan 5, 1968

By G. Akdogan, I. Mwandawande, S. M. Bradshaw, M. Karimi

The mixing characteristics of industrial flotation columns were investigated using computational fluid dynamics (CFD). Particular emphasis was placed on the clarification of the relationship between the liquid and solids mixing parameters such as the mean residence time and axial dispersion coefficients. The effects of particle size and bubble size on liquid dispersion in the column were also studied. An Eulerian-Eulerian method was applied to simulate the multiphase flow, while additional scalar transport equations were introduced to predict the liquid residence time distribution (RTD) and particle age distribution inside the column. The results obtained show that particle residence time decreases with increasing particle size. The residence time of the coarser particles (112.5 μm) was found to be at least 60% of the liquid residence time, while the finer particles (19 μm) had a residence time similar to the liquid. The results also show that an increase in the particle size of the solids results in a decrease in the liquid vessel dispersion number, while a decrease in the bubble size increases liquid axial mixing. Finally, the simulated axial velocity profiles confirm the similarity between the liquid and solids axial dispersion coefficients in column flotation.

May 2, 2022

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

"Chairman: Mr R. A. PLUMBRIDGE Rapporteur: Dr D. M. HAWKINSPapers:The relevance of computer methods to the economics of the mineral industry by R: A. PerlmanDynamic control of a mining enterprise by R. G. CoyleAn economic model of the mineral sands industry by G. P. A. HoweMr M. Splaine, in opening the discussion on Mr Perlman&apos;s paper, asked whether the model, as fitted by data up to 1963, predicted the rise in the price of copper in 1967, and whether the model could be used to capitalize on short-term price fluctuations.Answering the second question first, Mr Perlman said that the horizon used is six months to one year. In the very short term the activities of speculators obscured the effect of the fundamental econometric variables. This effect, however, was removed if one moved to a longer term, say, quarterly. In 1963 the model had predicted a price rise in 1964 and 1965 and a drop in price in 1966. The rise in 1967 had been caused by a strike, and imponderables such as large strikes were difficult to include in the model since they were unpredictable. Model simulation can be used to show the effect of strikes on price and the effect of small strikes is small.Mr B. R. van Rooyen said that because models are both calibrated and tested on historical data a bias was introduced which gave rise to an overoptimistic estimate of the accuracy of the forecasts. To this Mr Perlman replied that there seemed to be no alternative to the use of historical data for calibrating and testing models, and thus little hope of avoiding the bias. A second point made by Mr. van Rooyen was that manage¬ment tended to be suspicious of complex models and that frequently more heuristic models were sufficiently accurate and preferable for investment decisions. He added that if management were not involved in the model building the econometrician might easily go astray, Mr Perlman replied that symbiosis between data analysts and users of the model was essential and that the experience of the practitioner must be reflected in the model.Mr M. R. Fuller-Good remarked that a clear understanding of future price trends was essential for effective capital planning, and asked, first, how one went from the compiled data on supply and demand to the determination of their effect on price, record, whether necessary data, for example, capacities, could be obtained timeously, and, third, when strikes restricted supply, whether stockpiling by consumers induced large price fluctuations."

Jan 1, 2014

By K. M. Seiler

Automation in mining requires accurate maps of road networks on site. Because roads on open-cut mines are dynamic in nature and continuously changing, manually updating road maps is tedious and error-prone. This paper investigates the possibility of automatically deriving an accurate representation of the road network using GPS data available from haul trucks operating on site. We present an overview of approaches proposed in literature and test the performance of publicly available methods on GPS data collected from trucks operating on site. Based on shortcomings seen in all tested algorithms, a post-processing step is developed which geometrically analyses the created road map for artefacts typical of free-drive areas on mine sites and significantly improves the quality of the final road network graph.

Sep 1, 2021

By N. Wagner, P. den Hoed, J. D. Steenkamp, S. Soqinase

In pyrometallurgical processes, metal oxides are reduced from molten slag through carbothermic reduction. It is of interest to evaluate the reactivity of the carbonaceous materials towards substances such as slag. Characterization techniques such as coal petrography can provide insight into the influence of feed coal properties and how they potentially dictate reductant performance. This study aimed to compare the petrographically determined organic composition of coal to reductant reactivity. Two South African medium-rank C bituminous coals and one anthracite sample were investigated together with high-carbon ferromanganese industrial slag. The reductant reactivity tests were conducted at 1500°C in a muffle furnace to assess the potential of carbonaceous reductant in reacting with the main slag components. SEM-EDS was applied to understand the extent of MnO (and to a lesser extent, SiO2) reduction from the slag. Coal 2, consisting of a greater proportion of vitrinite (59.5 vol% on a mineral matter-free basis and 54.7 vol% including mineral matter) was the most reactive reductant. The anthracite sample, with the highest inert maceral proportions (71.8 vol% including mineral matter and 76.8 vol% on a mineral matter-free basis), was the least reactive reductant.

Feb 6, 2023

By K. C. Corin, M. S. Manono

The drive to reduce water usage globally has led to the mining industry reassessing its water usage - owing to past environmental degradation due to effluent discharge, tailings disposal and process water seepage into the water-table (Haggard et al., 2015). Factors such as water scarcity and environmental restrictions have created the necessity for recycling of process water in mining and other industries. Water recycling, however, causes an accumulation of ions in the process water, which may affect the strength of reagent action on the target mineral and in turn critical aspects of flotation may be impacted. Prior studies have shown that certain ions have specific effects on flotation: for example, calcium and copper have been found to enhance the adsorption of depressant onto gangue (Feng et al., 2013, Wang et al., 2016). Calcium and sulfate ions have been seen to give a higher concentrate grade than other ions present in process water (Manono et al., 2012). An increase in ion concentration will increase the mineral grade due to a decrease in entrainment (Corin et al., 2011). This study considers the impact of ion accumulation on reagent action and flotation response. Keywords: Flotation chemistry, water quality, ionic strength

Jan 1, 2020

By E. B. Viljoen

I. R. M. Chaston* As a gravity concentration man in the midst of so many eminent flotation experts I feel like Daniel. However, I would respectifully disagree with the opening remarks by Mr Viljoen. First, he suggested that gravity concentration of cassiterite was not effective in sizes below 30 microns. In a paper to the Institution of Mining and Metallurgy in 19621, I gave some figures for gravity concentration of deslimed material both for cassiterite and for wolfram which indicated that careful shaking table concentration of fine deslimed material could give recoveries of 75 to 90 percent in the size ranges above 13 micron. These were figures obtained from normal plant operation. It would be interesting to know if any tests were carried out on gravity concentration of the efficiently deslimed feed to this flotation plant to see what the recovery would be. Secondly, Mr Viljoen suggested that gravity concentration plants were expensive. He gives the cost of a flotation plant at R300 000 to treat a feed of 400 t.p.d. to the desliming section or 160 t.p.d. to the flotation cells. From his operating cost figures it would appear that the flotation cost is approximately R2 to R4 per ton of feed to flotation and the total operating cost about R2 per ton of feed. A table plant to treat this tonnage of deslimed feed would consist of about 30 tables and should cost considerably less to install and very much less to operate than the flotation plant. Third, Mr. Viljoen suggests that the concentrate grade from a gravity concentration operation would be unacceptably low. The paper quoted abovel showed that once a primary fine concentrate had been made, giving a suitably deslimed material, further gravity concentration could give concentrates of over 40 per cent Sn with high recoveries. Tailing from this dressing stage was naturally returned to the feed. To give these high grades, sulphides had been removed by flotation but this necessary flotation step is simple and cheap to operate and could be restricted to the final stage when the quantities involved are small. I would agree that flotation has a part to play in fine tin recovery but this role would only seem to become fully effective at sizes below 10 micron and would seem to require, as Mr. Viljoen has suggested, a mechanism for sizing which is effective down to, say, 1 micron. In the meantime it would be interesting to try tabling the flotation tailing to see if it was possible to recover the plus 20 micron cassiterite which is not recovered well by flotation. One point which has been made during discussion is the suggestion that cassiterite particles have a fully hydrated surface at normal pH. I wonder if this layer could materially affect the overall specific gravity of a very small cassiterite particle and, if so, whether gravity concentration of the very fine cassiterite would be improved if carried out in acid conditions, which would inhibit the formation of this hydrated surface. REFERENCES 1. CHASTON, I. R. M. &apos;Gravity concentration of fine cassiterite&apos;. Trans. Inst. Min. and Met. Vol. 71, p. 4, 1961 and 1962, and discussion of this paper. Dr. R. P. King Mr Viljoen has drawn attention to the difficulties associated with the presence of very fine particles in the flotation pulp and he has indicated that, on the Union Tin plant, they must sacrifice 30 percent of the cassiterite in the minus 7 /Lm material which they separate and lose. He has also indicated that the rate of flotation of cassiterite remained high at these small sizes. The problem arises because the very small particles stabilize the froth making it impossible to handle. These stable froths cannot be easily broken and therefore cannot be pumped and processed. It seems that further fundamental research work on the properties of stabilized froths is urgently required. We have found another difficulty associated with the presence of very fine particles in phoscorite slurries; these particles can be easily floated but with very poor selectivity. We believe that it is possible that a purely physical mechanism such as entrainment is responsible for the collection of fine particles in the froth. We have also demonstrated that the presence of fine particles in the pulp adversely affects the rate of flotation of the larger particles. For esample, we have found an increase in recovery of + 100 um material from 2 percent to 17 percent in a standard laboratory batch flotation test on phoscorite when the - 37 um was removed from the feed. Such interactions between particles are not universally recognised as an important aspect of the complex flotation mechanism. They should appear in any quantitative formulation of the flotation rate process.

This paper sets out to consider a specific type of corrosion protection system, which is referred to as a Duplex Coating system. The dictionary describes a duplex system as consisting of two elements or a “twofold” composition. The duplex system described in this presentation is such a two-part corrosion protection coating, viz, hot dip galvanizing as the firm base or primer, followed by a top paint system designed to combat severe corrosive environmental conditions encountered in nature. In principle, the duplex system is a cost effective and balanced, designed coating that is suited to the environmental conditions and service life requirements.

Jan 1, 2009