Search Documents

By C. R. S. Needes, M. J. Nicol, G. T. W. Ormrod, N. P. Finkelstein

The industrial application of a dioxide electrode uranium by C. R. S. NEEDES, Ph.D. (London) (Visitor), M. J. NICOL, Ph.D. (Rand) (Visitor), N. P. FINKELSTEIN M.Sc. (Rhodes), Ph.D. (Liverpool) (Fellow), and G. T. W. ORMROD (Visitor) A correlation between the potential of a U02 electrode and the rate of recovery of uranium has been proved in laboratory and plant trials. When the recovery rates change because of variation in the concentrations of Fe(III), Fe(II), SO4 'and H+, a positive correlation is observed. However, an 2- increase in the concentration of phosphate in solution produces an increase in the U02 electrode potential but a decrease in the rate of leaching of U02. The correlation between the U02 electrode potential and the rate of leaching of U02 is then negative. It is concluded that, as a control device, the electrode cannot compete with the platinum electrode for use on certain plants. Nevertheless, the U02 electrode will act as a useful warning device if the total concentration of iron in solution decreases to below a level concomitant with the economic recovery of uranium. Furthermore, because of the positive correlation between the U02 electrode potential and the phosphte concentration, the electrode will also be of value in the detection of an increase in the phosphate level in solution. When it was incorporated in a suitable industrial probe, the electrode was found to be able to withstand the rigours of the leaching conditions in a large pilot-plant pachuca, and only failed after six weeks' operation.

Jan 11, 1975

By G. G. Rogers, A. Vna Der Linde, N. B. Strydom, W. H. Van Der Walt

Changes in the level of serum vitamin C in mineworkers by N. B. STRYDOM, M.Se., Ph.D. (Illinois) (Fellow), G. G. ROGERS, M.Se. (Pta) (Visitor), W. H. VAN DER WALT, B.Se. (Poteh.) (Visitor), and A. VAN DER LlNDE, B.Se. (O.F.S.) (Visitor) The levels of serum vitamin C in the blood of mineworkers were determined on the first and fifth days of the normal heat-acclimatization period (i.e., before and after exposure to heat) and again after I, 2, and 4 months of underground employment. Supplementary vitamin C was administered to the men during the heat-acclimatization period. Six groups of 20 men featured in the study and, except for one of the two 4-month groups, all the values were obtained after a full shift of underground work. It was found that adequate levels of serum vitamin C were maintained during the heat-acclimatization period, and the 250 mg of vitamin C given daily to each man must therefore be regarded as sufficient. The serum vitamin C decreased significantly with time of exposure to underground conditions, showing that the vitamin C utilized during heat stress is more than that provided in the men's diet. At the end of 4 months, not a single subject had more than 0,4 mg of serum vitamin C per 100 ml, most of them having only 0,3 mg per 100 ml; 90 per cent of the men had had more than 0,4 mg per 100 ml during the acclimatization period. It is therefore recommended that the mineworkers' diets should be supplemented with 100 to 200 mg of vitamin C per man per day.

Jan 5, 1977

Specifile compendium' 80. Mining and engineering. (Obtainable from Specifile, P.O. Box 7870, Johannesburg 2000.) Reviewer: J. D. Austin SKF Steel. Plasmasrnelt information brochure. Hofors (Sweden), SKF Steel, 1980. Reviewer: N. A. Barcza POTENTIAL VALUE OF COLLIERY DISCARD MATERIAL By R B MacGillivray, Pr Eng, BSc(Eng) Rand, C Eng (Fellow) Preprints of perhaps the most thought-provoking of the papers delivered at the Witbank Coal Colloquium - 'Potential value of colliery discard material' by Roy MacGillivray of Rand Mines - are available on request from the South African Institute of Mining and Metallurgy. Mr MacGillivray outlines an imaginative plan to utilize the annual nine million tons of colliery discard in the WitbankBethal areas. Two SAIMM colloquia The South African Institute of Mining and Metallurgy (SAIMM) is organizing two one-day colloquia in the State Pavilion, Milner Park showgrounds, Johannesburg, to coincide with the Electra Mining Exhibition on 16th and 17th September. Over a million rands worth of equipment will be on display, the Electra Mining Exhibition being rated among the four or five largest in the world. The 1978 Electra Mining Exhibition was attended by 24 000 visitors. "Project Management in the Metallurgical Industry", "Mine Fires" APCOM International Conference by H. W. GLEN The 17th APCOM Conference (under the auspices of the Council for the Application of Computers and Mathematics in the Mineral Industries) was to have been held in Moscow during the last week in October. South Africans have always given enthusiastic support to the APCOM series of meetings, since their inception in 1961. The conference was held in the Republic in 1972.

Jan 1, 1980

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By G. P. O’Malley, A. N. Nikoloski

One of the most promising options for extraction of copper from low-grade chalcopyrite ores by heap leaching, however, chalcopyrite is refractory and suffers slow leaching kinetics and poor overall extraction due to formation of a passivation layer on the particles. The solution composition is believed to strongly affect the formation of this layer. This paper examines the effects of the major cationic species of Fe3+/2+, Mg2+, Cu2+, and Al3+ and the anionic SO42− species in acidic ferric sulfate media with a composition simulating recycle heap leach conditions. It was found that altering the sulfate, iron or aluminium concentration had significant effect on the copper extraction, the concentration of copper slightly influenced the extraction, and the amount of magnesium had no appreciable effect. Also, iron and aluminium caused a change in the sulfate concentration, and the sulfate ions had the greatest influence on the extraction of copper under recycle leach conditions

Jan 1, 2023

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020

By T. Moodleya, I. Govender

Despite the widespread use of DEM to simulate particle processes, comparatively little work has been done to evaluate its accuracy. One of the reasons is a lack of available measurement techniques that can capture dynamic information at the momentum transfer timescale which is lower than 10-6 s - typical of the kinetics occurring within the drum. This work makes use of Positron Emission Particle Tracking (PEPT), an in-situ method capable of measuring 3D kinematic data at 1000 frames per second. PEPT measurements are performed using 3 mm and 5 mm mono-size glass beads in a 300 mm diameter rotating drum at critical speeds that are relevant to industry. We undertake systematic ‘tuning’ of DEM with a view to optimising the agreement between experiment and simulation. To ensure an equitable comparison scale, both the DEM and PEPT data are coarse grained within representative volume elements. This work seeks to validate DEM predictions against experimentally derived PEPT kinematic measurements. Keywords: PEPT, nuclear imaging, DEM, Tumbling Mills

Jan 1, 2020

By P. M. Vercruijsse

Dredging is an industry in constant transformation. It has changed tremendously in the last decades. The traditional dredging activity, like construction and maintaining ports and harbours, desilting of drainage and irrigation channels, keeping reservoirs at depths and removing sediments from waterways, is still of importance. However, it is surpassed by other applications of dredging technology. Reclamation is an important example, where large amounts of sand are dredged, transported over large distances and used to make new land for industrial, housing, airport and other infrastructural purposes. Beach nourishment and other protective measurements should be mentioned here as well. Other applications like offshore winning of oil and gas, environmental clean-up, mining of interesting minerals like gold, diamonds, titanium and tin as well as aggregates from inland and offshore deposits are of importance. For all of these dredging applications equipment is required, and with changing circumstances and constraints, the design and use altered significantly. Larger dredging depths and increasing capacities require an impressive scale-up of equipment and tools. A demand for higher accuracy and selectivity set the requirement for a higher level of automation and control in combination with a well trained crew. Operations under more difficult circumstances and with other soil characteristics necessitated the development of new dredging components and systems. A sound basis for all developments was and still is a better understanding of the various dredging processes. This paper will highlight some eye-catching developments in the dredging industry. It will focus on issues in the field of hydraulic transport such as ever increasing capacity and dredging depth, as well as the pumping of large size materials.

Jan 1, 2007

By F. Yang, S. S. Long

Mixed fatty acids, such as oxidised paraffin soap, are frequently used as a substitute for oleic acid in flotation of scheelite in China. Not only because it is cheaper than oleic acid, but also because it is superior in flotation performance to oleic acid. This superiority is generally attributed to the mixed fatty acids' synergistic effect. In this paper, the synergistic effect of oxidised paraffin soap was investigated. We found it mainly consists of a series of saturated fatty acid salts, with six to nineteen carbon atoms. All the contained fatty acids were classified into four groups based on their chain length to make the research work practical. Also, the groups were labelled as 1, 2, 3, and 4 in order. The research was simplified into studying the synergistic effect of four equivalent collectors, instead of fourteen fatty acids. It is justified by the fact that neighbouring fatty acids are expected to have a similar flotation performance. The synergistic effect of the four groups of fatty acids was studied by single-mineral flotation with single groups, binary mixtures, ternary mixtures, and the full component, as collector respectively. The flotation performance index and synergy value were introduced to evaluate flotation performance and synergistic effect of groups, respectively. The results show that the mixture 1+2+3 has the strongest synergy of all followed by the mixtures 1+3 and 2+3. The mixture 3+4 and 1+2, on the other hand, have negative synergy. The synergistic effect of mixtures of groups indicate that being consecutive in length and a broad range of lengths are vital for fatty acids to enhance synergy. Group 3 is fundamental for the collecting action of 733 oxidised paraffin soap in the flotation of scheelite. The fatty acid soap in group 4 is not suitable for flotation due to its low solubility. Keywords: Mixed collectors, synergistic effect, scheelite

Jan 1, 2020

By S. Purushotham, Y. R. Murthy, M. Narasimha, S. K. Tripathy, M. Kumar

Spiral concentrators are gravity-based separators widely used to beneficiate coal, heavy minerals and beach sand. It consists of a helicoid trough that spirals downward in the helical configuration around an axial column. The particle segregation takes place based on size and density under the influence of gravity as the particles spiral down within the thin water layer. In the last century, most design modifications of this equipment were based on trial and error based lab-scale experimentations and empirical approach. The use of Computational Fluid Dynamics (CFD) has gained interest in the past two decades to understand the underlying flow physics in the spiral concentrators. In this paper, we used CFD to model the fluid flow and investigate the particle segregation inside a conventional LD9 spiral concentrator. Firstly, the Volume of Fluid model was used to resolve the liquid-air interface. The liquid depth and flow field predictions for varying flowrates were validated against the experimental literature data. One-way coupled VOF-LPT model was then used to describe the particle dynamics in the spiral flow field assuming dilute particulate flow. Moderate dense particulate flow (20 vol.%) was then modelled using the Algebraic Slip Mixture (ASM) model. Four particle-phases representing particles of different sizes of dual-density were simulated, and the component particle segregation was analysed. Keywords: Spiral concentrator, two-phase flow, multiphase, discrete phase model, ASM model

Jan 1, 2020

By G. G. Garrett, J. A. Peters, J. V. Bee, M. W. Atkinson

The development of steels with improved abrasion-corrosion resistance for use in underground components in South African gold mines is described in terms of design, manufacture, and performance. Based on the concept of microstructural design, new compositions were formulated to provide the optimum structures and properties. Extensive laboratory tests were conducted, and an industrial melt was produced. The resultant materials were tested for fabricability and machinability, and various components were manufactured. According to the preliminary operational results, these alloys exhibited outstanding performance in wear-plate tests, and are very promising for general application in underground components.

Jan 1, 1987

The paper discusses some theoretical aspects of Gy's sampling theory and provides reasons as to why it has found limited use in the mining industry, particularly for ores with low concentrations of values such as gold. These types of ores are referred to as low grade ores in the paper. It is shown that the misuse of the a priori liberation factor proposed by Gy is the main reason for the implementation limitation of Gy's model for low-grade ores. In addition, results of a case study done at the Gencor Geostatistics Department based On the new implementation of Gy's theory are provided.

Jan 1, 1996

By Timo Niitti, Antti Rinne, Janne Turunen, Klaus Schommarz, Sami Grönstrand

This paper captures the essential steps employed in developing Outotec?s new FloatForceTM mechanism. The development of a flotation mechanism essentially revolves around the efficient transfer of installed power, or capital cost, to optimum flotation performance. Optimum flotation performance will be achieved if a balance between metallurgical results, operating and capital costs is maintained. The development of the FloatForceTM mechanism was done by careful evaluation of each of these three areas. This paper focuses on how experience, CFD and laboratory equipment, pilot and plant tests are used to test and evaluate a new flotation mechanism. Validated variables include mixing profile, power draw and local air hold-up. Metallurgical and mechanical design considerations are not covered in this paper. Besides using the FloatForceTM mechanism in new flotation equipment, the FloatForceTM mechanism can be used in existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented.

Jan 1, 2007

By Richard J. Robbins

Raise and shaft drilling, a continuing development RICHARD J. ROBBINS* (Visitor) Although the past decade has witnessed many improvements in large-diameter drilling machinery for the boring of raises, there is still room for improvement both in operational use and in the design of equipment. Some of the available machines are described and illustrated, and it is concluded that the possibilities of new systems and designs should continually be re-assessed since the factors that determine their feasibility, such as bore diameter, cutter costs, and penetration rates, are changing rapidly.

PREFACE During the past year, the Council of the SAIMM undertook a major strategic-planning exercise to review all its current activities, and to redefine its scope and objectives in the light of changing circumstances. The following are the four main concerns that prompted Council to take stock of the situation. (1) Over the past five years, the SAIMM has become heavily involved in a variety of new activities. (There are many examples, of which the expansion in book publications and the establishment of physical metallurgy as a third major discipline with its own colloquia and schools are perhaps the most important.) While these new activities have considerably broadened the SAIMM's scope, they have resulted in a significant increase in the day-to-day workload of the President, Office Bearers, and Council members, and of the secretarial staff based at Kelvin House.

Jan 1, 1986

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

Hydrometallurgical processing of complex ores and concentrates is becoming increasingly important as the mining and metallurgical industry seeks to exploit mineral deposits that are difficult to treat using conventional mineral processing and pyrometallurgical technologies. Mineral processing is often challenged by the difficulty or inability to separate valuable minerals into marketable concentrates. Hydrometallurgical processing, using selective leaching technology, can often ?chemically beneficiate? such difficult deposits. Pyrometallurgical treatment of base metal concentrates is capital intensive and subject to ever more stringent environmental control. Hydrometallurgical processing is generally lower in capital cost for an equivalent metal production rate and avoids the gas and dust issues associated with pyrometallurgical processing. The possibility of by-product recovery may also increase with hydrometallurgical treatment. Two examples of new technology or flowsheet development for treatment of complex ores and concentrates are used as illustration. These include the El Boleo process of Baja Mining for recovery of copper, cobalt, zinc and manganese from a complex clayey ore and the PLATSOL? process for recovery of copper, nickel, cobalt, platinum, palladium and gold from a bulk sulphide concentrate.

Jan 1, 2009

By C. Mueller

In many automated mines, multi media video and audio funtionality has to be combined with sensor information or steering commands, which is the idea of a new, PC based integrated and multi media capable control system. The new control system (Multimedia Control - MMC) bases entirely on TCP/IP networking and internet technology. For the first time, this enables the ‘intelligent’ use of video and audio information: pictures and voice sequences may be forwarded on request only, they may be stored if particular events occur (e.g. video black boxes) and sensor signals as well as actions from the automation system can directly be assigned with multi media sequences. MultiMedia Control entirely bases on object oriented software. It uses most modern software technology. As user interface, only a standard web browser is required. This makes the handling of different machines easy. By using mobile web pads, dedicated local operator interfaces are not required any longer. The service staff just connects to the automated equipment by – wireless –LAN to make required adjustments. Customization is easy using an open Application Programming Interface. Software modules may be added to the system without touching or recompiling existing components. The system was prototyped in 2000 using a demo-application. The performance tests showed very positive results both regarding the control system behaviour and the speed/latency timing behaviour of the multi-media information processed. The system now is slightly reshaped to completely meet the final product requirements. It is expected to be available by the end of 2001. Key words: Machine Automation; Control System; Multi Media; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Streaming Video; Quality Assurance; Service; Control Centre.

Sep 1, 2001

By K. Shin

Determining the anisotropy of rocks has in the past been difficult and rarely attempted in engineering practice. Here we have developed a new practical methodology for measuring orthotropic anisotropy that requires only one hollow cylinder specimen to determine the anisotropy of a set, even when the directions of the anisotropic axes are unknown. Autrefois, la détermination de l’anisotropie des roches était difficile et elle a été rarement essayée dans la pratique de l’ingénierie. Voilà c’est nous qui avons mis au point une nouvelle méthodologie pratique pour mesurer le coefficient de conductibilité thermique de l’anisotropie qui exige un seul spécimen du cylindre creux afin de déterminer l’anisotropie d’une série, même si les directions des axes anisotropiques sont inconnues. Früher war die Bestimmung der Anisotropie von Gesteinen ein schwieriges Verfahren, das in der technologischen Praxis nur selten in Angriff genommen wurde. Wir haben hier eine neue praktische Methodik zur Messung der orthotropen Anisotropie entwickelt, bei der nur ein Hohlzylinder an Gesteinsproben benötigt wird, um die Anisotropie einer Reihe von Steinen zu bestimmen, selbst wenn die Richtungen der Anisotropieachsen unbekannt sind.

Jan 1, 2003

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979