Search Documents

By B. T. Brady

Laboratory measurements by the Bureau of Mines indicate that failure in dry rock specimens measuring approximately 13 cm in length is preceded by tilt anomalies lasting a few milliseconds. The tilt behavior is qualitatively similar to that reported to precede earthquakes. Test results suggest that the time duration of this tilt anomaly for laboratory specimens of this length is independent of rock type, in agreement with theoretical predictions and other experimental data on rock failures including earthquakes.

Jan 1, 1975

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

This laboratory has developed a sensitive electro-optical method to quantify the initial rate (R) and total amount.(MAX) of superoxide (SO) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope to visualize PAM in culture, and to video record the images during the time the cells produce SO. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of SO, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin were added to the medium (in vitro). R and MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using serum which permits PAM to be restimulated by different dusts to help establish a dose response effect, and a means to study the effects of lung surfactant on modifying the toxicity of inhaled dusts. Long term, this methodology should provide useful insight· into establishing the role SO plays in the phagocytosis of inhaled dusts and bacteria, in PAM dysfunction, and in lung diseases such as pneumoconioses. Supported by the Department of the Interior's Mineral Institute Program administered by the Bureau of Mines through the Generic Mineral Technology Center for Respirable Dust (G1135142).

Jan 1, 1988

By C. Travis Anderson

 The general conclusion of earlier investigators was that the action of sulfur dioxide on manganese oxides of Cuyuna ores was not sufficiently pre- ferential to be attractive as the basis for a commercial process. Bradley4/ and his coworkers discarded it for leaching with boiling ammonium sulfate solution, and Sweet5/ used a baking operation to render the iron insoluble. These results were confirmed by the early tests in the present investigation, which were made on brown ores (Sagamore), using acid additions, because at that time the Technologic Committee on Manganese held the opinion that these ores constituted the major available reserve in the Cuyuna district. However, when it appeared that the black ores, or the formation in which they occur, were a possible source of a large tonnage of manganese, the use of sulfur dioxide and sulfuric acid leaching was again reviewed, and a satis- factorily preferential action on the manganese was found. It was originally thought that the use of sulfuric acid ahead of, or at least with, the sulfur dioxide simplified the process, particularly by preventing formation of dithionates. Removal of the phosphorus from the solution by neutralization with lime or fresh ore was suggested. The tests recorded in this report indicate that it is not practicable to use enough acid to prevent formation of dithionate and that the value of excess sulfuric acid is doubtful, particularly in regard to satisfactory manganese:phosphorus and manganese:iron ratios.

Jul 1, 1942

By A. S. Griffiths, J. E. Evans

Noise processing experiments with ELF (3 to 300 Hz) atmospheric noise and signals in the 40 to 80 Hz range are described. The primary purpose of the experiments was to record and analyze wideband ELF noise in order to design the noise processing portion of a receiver which minimizes the required transmitter power. The application of appropriate theory and extensive simulations led to a noise processor which consists of the following functions: (1) a compensating (or whitening) filter, (2) a prenotch filter clipper, (3) notch filters at frequencies of manmade interference (e. g., power lines), (4) a post-notch filter clipper, and (5) a phase-coherent linear matched filter. The nonlinear processing provides considerable gain relative to a linear receiver (i. e. , a receiver consisting only of a matched filter and appropriate whitening filters). It is convenient to measure sys tem performance in terms of an "effective noise level" which is equal to twice the received signal energy divided by the signal to noise ratio at the matched filter output. For example, the highest effective noise levels observed at 45 Hz with the nonlinear processor were about -134, -131 and -137 dB wrt 1 amp/m [Hz] using Saipan, Malta and Norway data, respectively, compared to 1 percent exceedance levels of effective noise for the linear receiver of about -115, 115 and -130 dB wrt 1 amp/m [Hz] respectively.

Jan 1, 1973

By Gerrit V. R. Goodman

Supplemental water sprays were placed along the sides of a continuous mining machine to improve suppression and confinement of the dust cloud under the cutting boom to re- duce downwind dust levels. Using a full-scale mock up of a continuous mining machine, preliminary work showed that these side sprays improved suppression of the dust cloud and redistributed this cloud under the cutting head. This led to reductions in dust levels around the machine and in down- wind airways for some positions of the mining machine. This testing also showed that side spray effectiveness was influenced by the distance from the fresh air ventilation device to the cutting surface, termed the ventilation setback distance. These sprays produced larger reductions in machine and re- turn dust levels at smaller setback distances than at larger setback distances. These side sprays then were installed in similar locations on a mining machine at an underground coal mine operation to evaluate their effectiveness for im- proving suppression and capture of dust by the flooded-bed dust scrubber. Although sampling could not be conducted successfully in the return, sampling around the mining ma- chine and at the machine operator showed that dust levels decreased with use of these sprays. Further analysis showed that these sprays were most effective at the smaller setback distances, a result confirmed by full-scale laboratory testing. Keywords Occupational Health, Dust Sampling, Coal Mining. Continuous Mining, Control Technology

By J. A. Zimrner, R. J. Tirnko

The roles of main mine fans in underground mines are to induce airflow and continuously re- move hazardous gases and dust. While most larger mines use multiple fans to accomplish these tasks, many smaller mines employ only a single fan. This paper concentrates on those mines having only one fan to provide ventilation needs. If this fan should cease to function, it is likely that methane concentrations will in- crease in some areas of the mine. As a safety precaution, Federal Regulations require that personnel must be- gin evacuating the mine within fifteen minutes after fan stoppage. Powered haulage can be used to transport workers to the mine portal as long as travel is through areas where hazardous levels of methane are not expected. To determine where methane will accumulate along haulageways during a fan stoppage, air samples must be taken at specific areas and analyzed for hazardous gases. During this study, procedures were developed for measuring methane levels along the haulegeways that are used to exit a mine following stoppage of the main mine fan. Methane levels were measured in four different mines at selected underground locations during four planned fan stoppages. In these mines the measurements taken only at the specified locations showed that, if workers had used electrically powered haulage to exit the mine following a fan stoppage, the methane accumulated along haulageways during fan stoppages would not have significantly increased the risk of an ignition.

By D. K. Ingram, G. L. Mowrey, T. R. Rehak

This paper summarizes fly rock and blast area security fatalities from 1989 to 1999 and examines the causative factors. Coal and nonmetal mining used about 43 billion pounds of explosives and blasting agents between1989 to 1999. A majority of this consumption was used at surface mines. Accident data indicates that fly rock and lack of blast area security were the primary causes of blasting related injuries in surface mining. Fatal injuries due to lack of blast area security were attributed to: failure to clear blast area; failure to follow instructions; inadequate guarding; inadequate blasting shelter; and unsafe location. Seven fatalities due to fly rock and lack of blast area security were reported in surface coal mines and six in nonmetal mines. Out of these, two fatalities (one each in coal and nonmetal mines) occurred outside the mine property. In the coal mining sector, two fatalities were attributed to fly rock, and five to lack of blast area security. In the nonmetal mining sector, three fatalities were attributed to fly rock, and three to lack of blast area security. Preventive measures include: ensuring that all personnel have evacuated the blast area during shot firing; using adequate blasting shelters for employees whose presence is required in the blast area; controlling and monitoring all entrances to the blast area; ensuring that the blast is properly designed, drilled, and loaded; and emphasizing education and training to enhance skill levels for implementation of engineering control techniques.

By Lloyd A. Morley, Robert Stefanko

This report has presented a literature review of explosion proof¬ing of coal mine electrical equipment. The international "state-of¬the-art" is an extremely difficult definition to quantify but, from the preceding paragraphs, it is evident the international community be¬lieves that it is represented by the International Electrotechnical Commission's Publications. Five questions were set forth during the beginning of this report. Each will be evaluated in light of the preceding discussion. 1. Can Schedule 2G specifications on explosion-proof containers be substantiated? Literature was found in the three main problem areas, surface temperature, mechanical strength, and explosion transmission, to determine this. Surface temperature requirements are adequate except for equipment that can normally overload, and the required intern¬al pressure does afford some margin of safety. However, in terms of safety, gap dimensions are about ten times smaller than that needed. 2. Is it possible to replace the Schedule's design requirements with performance specifications? Two primary areas were determined as mechanical strength and explosion transmission. As was mentioned, for present flange and gap standards, the 150 psig requirement is adequate. Furthermore, it is the authors' opinion that the level cannot be re¬duced if the present gap requirements are retained. The Schedule now requires that 16 tests be run, but the literature suggests that only from three to six examinations are necessary. Then by using the abso¬lute maximum pressure from these measurements or 150 psig, whichever is

Jan 1, 1974

By Bruce K. Cantrell, Stephen W. Stein, David Hassel, Harvey Patashnick

The Mine Safety and Health Administration. Department of Labor, requires coal mine operators to measure compliance with federal re¬spirable dust exposure standards periodically using approved gravi¬metric samplers. However, the gravimetric approach, with its inher¬ent delays, cannot provide dust concentration data quickly enough to allow on-site correction of inadequate dust control strategies or re¬moval of personnel from harmful environments. Furthermore, alleged tampering with dust samples collected to determine compliance with standards prompted the Secretary of Labor to appoint a special Respirable Dust Task Group to study options to improve monitoring and control of respirable coal mine dust. The Mine Safety and Health Administration's Task Group recommended that the U.S. Bureau of Mines develop a fixed-site monitor that would provide continuous information to the mine worker and mine operator regarding dust levels and the status of compliance with the applicable respirable dust standard. In response to the Mine Safety and Health Administration's request, the U.S. Bureau of Mines is investigating several sensor tech¬nologies for continuously monitoring respirable coal mine dust. One of these technologies is the Rupprecht and Patashnick Co. tapered element, oscillating microbalance. The bureau is in the process of investigating the suitability of using this sensor in the high humidity and vibration environment of underground coal mines. Laboratory tests have indicated that, with modification, the sensor can meet the humidity and vibration requirements for underground coal mine use. Currently, the bureau is developing

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining, on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 44,015 employees worked in underground mining locations in 2003, corresponding to 44,778 full-time equivalent (FTE) workers. • Ninety percent of underground employees (n = 39,735) were mine operator employees. • Contractors comprised 10% of all underground mining employees (n = 4,280) and comprised only 5.8% of all underground FTEs. • The majority of underground employees worked for coal operators (73.0%; n = 32,130).

Feb 1, 2005

By N. S. Dalal, B. Jafarl, M. M. Suryan, V. Vallyathan

"The biologic events leading to coal workers' pneumoconiosis (C'WP) are not yet fully understood. There is no good correlation between toxicity studies or animal models with human epidemiologic and pathologic data. Several studies have shown that the severity and prevalence of the CWP in miners correlate strongly with the rank and type of the coal mined. However this has not been found to be the case with laboratory animal models or in vitro studies. In 1980 Russian scientists Artemov and Resnik suggested that the discrepancy may be related to the excessive amount of short-lived free radicals present in freshly generated coal mine dust. Because of their short life, such free radicals would be absent in the ""stale"" coal dust used in most animal experiments. To test this hypothesis we have undertaken a systematic study of the generation, reactivity with oxygen and biological significance of free radicals in coal dust.Electron spin resonance (ESR) was used as a technique for the direct detection of radical production and kinetics of decay. ESR signals from the newly generated radicals decreased with time on exposure to oxygen or when stored in biological buffers at a rapid rate. In vitro biological tests were carried out which suggest that the reaction between the newly generated radicals and oxygen plays a significant role in the sample's cytotoxicity.Materials and MethodsESR measurements were made at X-band (~9.7 GHz) using a computer-controlled Bruker ER200D ESR spectrometer. 11te two coals studied in detail were obtained from the Pennsylvania State University Coal Depository. These were, a bituminous sample, PSOC-1172 (72% carbon) and an anthracite sample, PSOC 867 (95% carbon). Coal particles of several millimeter (mm) dimensions were evacuated to a pressure of ~10-3 mm Hg typically overnight. Without exposure to air, these particles were ground in an agate mortar with an agate pestle for about 30 minutes and then sieved through a 20 \1111 mesh filter before ESR measurements or cytotoxicity studies. As an index of cytotoxicity, hemolysis was measured according to the method of Harrington, with minor modifications. Sheep erythrocytes (2%) were incubated with test samples at 37°C for one hour, and the hemoglobin released was quantitatively estimated photometrically. Additionally, release of alveolar macrophage enzyme lactate dehydrogenase (LOH) was estimated after incubation of the macrophages with the coal particles at different time intervals after the grinding. Enzyme activity was assayed according to the method of Wrobleski and LaDue and expressed as percent of enzyme released in 2 hours per million cells with 1 mg of coal."

Jan 1, 1989

By Isaac A. Zlochower, Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coats, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane-air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

By Hans M. Cassel

The specific objective of research presented in this report was clarifi- cation of physicochemical fundamentals of the mechanism of dust explosions. The equipment, techniques (chiefly photographic), and dusts (chiefly graphite and light metals) employed are described. From behavior of individual par- ticles, conclusions are drawn as to their cooperative function in ignition and combustion of dust clouds. Results are interpreted using thermal theory as accepted for combustible gas mixtures. Radiative transfer across the flame front, as a characteristic of dust flames, is given particular atten- tion. Related studies by other investigators are discussed.

Jan 1, 1964

By I. AITKENS

Tourmalines are among the most beautiful of all the semiprecious stones, and are unsurpassed even by corundum in variety of hue. The stones most suited to jewelry purposes are those comparatively free from iron. One reason for the fact that the tourmaline has advanced rapidly in public favor in this country is that it is found in California in great profusion and of extraordinary quality. The superb green and especially the pink crystals found at Pala and Mesa Grande in San Diego County, Calif., are deemed superior to tourmalines from all other localities.

Nov 1, 1931

By John W. Buch

"INTRODUCTION The Ruhr coal basin is estimated to cover an area of more than 1,000 square miles. Here, the total thickness of the coal bearing formation (Carboniferous) is 10,500 feet, and drilling-hole have revealed 92 coal beds with a total thickness of 262 feet. 6/ Beds pitch from 0 to 90 degrees and about 70 percent of the wartime production came from beds that pitched less than 30 decrees. 5/For example at the Minisiter Stein mine, there are 24 minable coal beds ranging from 80 centimeters. (2 ft., 7 1/2 in.) to 250 centimeters (8 2 1/2 in.). The vertical thickness of the measures is 1,000 meters (3,200 ft.), and at this mine the deposits are covered with 150 meters (500 ft.) of surface wash. The cross section (fig, 1) at Fritz mine; Hoesch, A.G., Essen, Ruhr, is characteristic, The mines have been developed and worked to vertical depths of 2,000 to 2,500 feet by vertical shafts; main-level intervals are 500 to 700 feet apart. Haulage roads are straight, driven in rock, and centered as nearly as practical between property boundaries. Levels are sectionalized by driving crosscuts at right angles to the main haulage road on 800- to 900-foot centers. The roads are the main transportation arteries for the use of trolley or Diesel locomotives. A plan of the sixth main level (fig. 2) at the Bruchstrasse mine; Gelsenkirchener A.G., Bochum, illustrates main-level development and,sectionalizing with crosscuts. The cross section in figure 3 is that of the fourth crosscut west at the same mine."

Oct 1, 1946

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Haiti has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930