Search Documents

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface coal mines by state during 1990-1999. Table 19 also shows by state the risk rates, employees' working hours, lost workdays, and coal production. For surface coal mines, 215 fires occurred in 21 states during 1990-1999. Ninety-four of those fires caused 93 injuries and I fatality (the yearly average was 21.5 fires and 9.3 fire injuries). Fourteen fires and seven injuries involved contractors. The Ewhr value was 729 x 10° hr (In = 0.026), the CP value was 6,355 x 10° st (Fn = 0.034), and the LWD value was 8,141. Kentucky had the most fires and fire injuries (45 fires and 23 injuries), followed by Pennsylvania (33 fires and 14 injuries), West Virginia (25 fires and 14 injuries), and Indiana (20 fires and 8 injuries). Among these states, Pennsylvania had the highest fire risk rate value (Frr=0.145), while Kentucky had the highest injury risk rate value (In 0.041).

Jan 1, 2004

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1965 was improved slightly, as indicated by the reduced injury-frequency and severity rates. The overall operating activity was higher in 1965 as measured by the gains in the number of men working and in the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.65 per million man-hours in 1965. This overall rate comprised frequencies of 0.28 for fatal and 17.37 for nonfatal work injuries, of which both were slightly better than the corresponding rates of 0.29 and 17.53 in 1964. Fatalities totaled 537; 5 less than in 1964. However, the total of 32,982 nonfatal injuries was 575 higher than in 1964. This larger number of nonfatal disabilities was offset by the increased worktime so that the nonfatal frequency rate decreased in 1965.

Jan 1, 1967

By Wilbur I. Duvall

The borehole deformation gage and overcoring techniques developed by the Bureau of Mines form one of the primary methods of determining in situ rock stress. This report describes a least squares method of calculating the average rock stress components in the horizontal plane from more than three diametral deformation measurements in a vertical borehole. This least squares analysis provides a means of determining the multiple correlation coefficient, the variance, and the scatter for a set of deformation measurements. From this information, confidence limits can be calculated for the secondary horizontal principal stresses and their directions. The material presented in this report can be used as a guide to the development of least squares solutions for stress measurement techniques other than the borehole deformation method. Since the statistical information that results from the least squares method is extremely useful in the interpretation of results, it is recommended that a least squares analysis be used on stress measurement data whenever possible.

Jan 1, 1979

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of Al-Ni alloys con¬taining 0.54 to 30.04 atomic percent nickel with the aid of the high-temperature galvanic cell Al(1) // Al+3 (AlCl3 in NaCI.KC1) // Al-Ni alloy (1 or s). Activities of aluminum and nickel (compared with pure liquid metals as the standard state) show pronounced negative deviation from Raoult's law at 1,273 K. The properties [?G, ?Gxs, ?G ideal, ?GA1, AGxs1, ?Gni , and ?GNixs] have been derived from the experimental data and are summarized in tables and illustrations. At 1,127 K, the thermodynamic stability for the invariant three-phase equilibrium consisting of a saturated liquid, A13Ni, and A13Ni2 has been uniquely defined by an activity for aluminum of 0.751. A free energy of formation at 1,127 K of -7,940 cal/g-atom was derived for the compound A13Ni.

Jan 1, 1975

By W. Blake, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mines collected and analyzed over core measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 1995

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 6 Automatic Elevator Control Systems An automatic elevator control system, consisting of position sensing devices and a control unit, can be used to control an emergency mine hoist. While automatic elevator control systems are assembled from standard components, they are typically custom designed to suit a given customer's application. Various manufacturers contacted indicated that the price range, less installation, for a simple two-stop control system begins at approximately $2500 and can increase depending upon the type of components used, shaft depth, the type of mechanical drive used, and the maximum operating speed A partial list of elevator control manufacturers follows. They should be contacted for further details. Marshall Elevator Company Pittsburgh, P A 412 -431 -1340 Armor Elevator Company, Inc. Louisville, KY 502-361 -7181

Jan 1, 1976

By B. Dimitriades

The Bureau of Mines measured the reactivities of 19 hydrocarbons known to be prominently present in automotive exhaust and ambient air in a smog chamber. Results agreed well with those obtained using two other smog chambers. Reactivity scales were developed for hydrocarbons and aldehydes using the results of this work and those of a previous study. Application of the reactivity scales to automotive exhaust samples gave fair agreement between predicted and observed rate-of-N02-formation values; however, predicted and observed ozone yields were neither in agreement nor did they correlate well. This lack of correlation for ozone yield was attributed to the inappropriateness of (1) the individual component reactivity data, (2) the reactivity classification scheme used, and (3) the linear summation method. In seeking to understand this problem and to develop more appropriate reactivity scales, the data were examined from a reaction mechanism standpoint, and further studies were suggested.

Jan 1, 1975

By David M. Hyman

Outbursts are sudden and violent releases of gas and coal that result from a complex function of geology, stress regime, and gas pressure and content. The Bureau of Mines has reviewed methods for prediction and mitigation of such outbursts in use worldwide, as an aid in selecting the proper techniques for use in specific mine environments. Outburst-prone coal may be distinguished from normal coal by its sorption-desorption velocity. Three types of methods used to characterize the kinetics of sorption-desorption are described; all are based on the ability of outburst-prone coal to release, through desorption, methane or carbon dioxide much more rapidly than normal coals. Other prediction methods, based on borehole samples, are also described. Various mitigation methods described and evaluated include (1) working the least stressed, less disturbed, lowest gas content seam in multiple-seam areas; (2) mine opening geometry; (3) inducer shot firing; (4) water infusion; (5) localized stress relief, using boreholes or by cutting a reliever slot in the longwall face; and (6) other gas drainage methods.

Jan 1, 1987

By John G. Kovac

A computer simulation has been developed by the US. Bureau of Mines to estimate the chances of a miner making a successful escape while wearing a self-contained self-rescuer (SCSR). The model takes into account (1) training in the use of SCSR's, (2) apparatus integrity, and (3) oxygen cost of a mine escape. This report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By Daniel Edelstein

Demand for arsenic trioxide increased markedly during 1984 as a result of increased use of arsenical wood preservatives and increased use of arsenicals in agriculture. The increase in agricultural demand was due to a return to production of land with-held from cotton planting under an agriculture program for acreage diversion for some 1983 crops. Supplies of arsenic trioxide were more than adequate to meet increased demand, and prices either declined from, or remained at, the low 1983 levels. In June, ASARCO Incorporated announced plans to close its Tacoma, WA, smelter by mid-1985. Domestic Data Coverage.-Refined arsenic trioxide was produced by two U.S. companies. The major producer voluntarily reported its production to the Bureau of Mines, but to prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1985

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 4 Illustrative Simulations The capabilities of the program are demonstrated by simulating various evacuation cases in different situations for a particular mine. The mine selected for the illustrative simulations is the mine I C' , as described in Section 2, chosen particularly because of availability of mine characteristic data and mine evacuation results for test drills. These evacuation results can be used to verify validity of the predictions made by the program A.4 1 Mine Characteristics A schematic diagram of the mine is shown in Figure 19. The figure shows all the major shafts, drifts, raises and stopes of the mine in the form of a network. There are four hoists, Hoist No. 1 and Hoist No. 2 are assumed to be single drum hoists and Hoists Nos. 3 and 4 form part of a double drum hoist, with Hoist No. 4 being the main hoist (master hoist) The positions of the 133 miners, typically working in a day shift of the mine, are also shown in the figure. The miners are identified by a miner number, and their total number on each level is chosen from the data on the fire drill simulated as Case No. 1 in the illustrative simulations.

Jan 1, 1976

Aid mine operators as well as mine inspectors in making quick but sufficiently accurate measurements of the rock dust content of coal/rock dust mixtures. The Problem Past research has shown that accumulations of volatile coal dust in underground coal mines can be rendered non-explosive by dilution with chemically inert rock dust (usually limestone). Consequently, rock dusting is required by law in U.S. underground coal mines. However, mine officials and inspectors have no quick and reliable means to determine whether enough rock dust has been applied to achieve a mixture that is in compliance with the law. Even the compliance tests used by the Mine Safety and Health Administration (MSHA) are slow and involved. MSHA assures that a mine has been rock dusted adequately by collecting samples from rock dusted areas of the mine and sending the samples to a laboratory for analyses of the inert-dust content. The analyses may not be completed for more than two weeks, during which time the mine in question might be inadequately protected against coal dust explosions. To solve this problem, the Bureau of Mines devised a quick, simple and reliable device that can immediately determine the rock-dust content of a mixture of coal and rock dust.

Jan 1, 1985

By Seth C. Schaefer

The Bureau of Mines studied the standard free energies2 of formation of ferrous fluoride (FeF2) and ferric fluoride (FeF3) with high-temperature galvanic cells employing calcium fluoride doped with 1 mole-pet yttrium fluoride as the electrolyte. A free-energy change for the cell reaction Fe (s) + NiF2 (S) = FeF2 (S) + Ni (s) together with the standard free energy of formation of nickel fluoride yields a standard free energy of formation of ferrous fluoride from the elements of ?GF° = -168.74 + 30.63 x 10-3T ± 0.41 kcal/mole (897-1,098 K). (2) Combining the standard free energies of formation of magnesium fluoride, ferric oxide, and magnesium oxide with the free-energy change for the overall cell reaction 3MgO(s) + 2FeF3 (s) = 3MgF2 (S) + Fe2 03 (S) (3) gives a standard free energy of formation of ferric fluoride from the elements as ?Gf° = -281.45 + 90.46 X 10-3T ± 0,67 kcal/mole (880-935 K). (4) Free energies and equilibrium fluorine pressures for the two univariant equilibria of the Fe-F system are tabulated and illustrated.

Jan 1, 1975

Rank the dust knockdown (airborne capture) ability of six different types of water spray nozzles, Approach A fixed quantity of dust is released into a large, closed chamber in a laboratory. Water sprays are turned on inside the chamber and their effectiveness on the dust cloud is evaluated from the rate at which the dust disappears. This method better simulates dust suppression underground than methods tried earlier. The results of the laboratory test were confirmed by conducting tests on a full-scale mod-el continuous miner face where dust levels were measured in the return airway. Results of the Closed Chamber Tests The graph indicates that atomizing nozzles provide the best use of water for dust scrubbing. However, use of these nozzles is limited by their susceptibility to damage and clogging. Hollow-cone nozzles perform almost as well as atomizing nozzles. Test results also indicate that full-cone, venturi-assisted, and flat-fan spray cones are about two-thirds as effective as hollow-cone nozzles. The least effective were venturi nozzles designed for moving air. The most significant advantage of hollow-cone nozzles over other nozzles tested is reduced clogging due to larger orifice size. The hollow-cone nozzle used in the test and depicted by the graph was type BD-3 manufactured by Spraying Systems Co., Wheaton, IL. This nozzle is already used on many continuous miners. Other hollow-cone nozzles of

Jan 1, 1982

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963

This report describes magnetic field measurements in the Helvetia Coal Co. Lucene #8 Mine for purposes of deriving a mapping of the magnetic field strength covering the major haulageways which contain conductors. The measurements were performed by Terry S. Cory, P.E. under U.S. Bureau of Mines purchase order P0372716. Assisting in performance of the measurements were personnel from the Bureau of Mines, PMSRC, and Helvetia Coal Co. Acknowledgement is given to Engineer Tom Strong of Helvetia Coal Co. who accompanied the measurement team and who lended support in performing the measurements and in supplying valuable engineering information for use in evaluation of the results. The results of the testing at medium frequency show that coverage of the entire mine area containing conductors can be achieved employing wireless radio techniques whereby radio signals are coupled into and are carried by these conductors. These results confirm earlier qualitative testing of the Collins Mine Wireless Radios in this mine. These results, performed over the frequency range 71-2890 KHz, illustrate the effect of frequency on the radio propagation with the conclusion that the best overall coverage is obtained at frequencies approximating 1000 KHz. This report presents all the raw data and the reduced data in the form of magnetic field strength contour maps. Sufficient information is provided to enable independent reduction of the data. A summary of observations which can be made directly from the contour maps is given.

Jan 9, 1977

By J. E. Chilton

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

By James A. West

THE South Asian countries of India, Ceylon, Pakistan, Afghanistan, Nepal, Bhutan, and Sikkim have a large variety of mineral resources; however, in spite of mineral industry growth during 1964, development of resources remained far short of possible development, and, in terms of value of trade in minerals, the area remained a sizeable net importer. India's mineral industry is by far the most significant; its minerals production in 1964 accounted for more than 90 per cent of the total value of all minerals produced in the area. The total value of all minerals produced in South Asia in 1964 was only about 1 percent of the area's estimated gross national product of $55,125 million. Despite the rather small current contribution of minerals to the economy, development of mineral resources figures prominently in plans for the industrial development of the nations of this area.

Jan 1, 1966

By W. S. Wright

"INTRODUCTION The Ward copper deposit was brought to the attention of the Bureau of Mines in September 1943 by John J. Knob, 217 E. Penn Street, Long Beach, N. Y. At that time all Bureau of Mines work on Seward Peninsula was being directed to the exploration of deposits of tin, a metal high on the strategic list. It was not until September 1946 that the Bureau could make a preliminary examination of the Ward prospect.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.Acknowledgment is extended to Robert S. Sanford, acting chief of the Alaska division, under whose supervision all exploratory work of the Territory is conducted."

Aug 1, 1947

By G. V. Sullivan

This report describes an investigation by the Bureau of Mines of flotation techniques for the recovery of chromite from fine-grained disseminated ores. Reported work on the concentration of chromiferous materials shows that flotation has been applied almost exclusively to slime-free pulps. Therefore, chromium recoveries that could be obtained by flotation were related to the amount of slime rejected. However, results of recent studies by the Bureau of Mines showed that des liming is not a requisite to selective concentration of chromite. Laboratory-scale tests on seven ore types from the more important chromium-bearing areas of the Pacific Northwest showed flotation to be technically feasible for treatment of all but one of the samples. Concentrate grades were affected more by the composition of the chromite mineral than by the grade or character of the ore. Test results from three of the samples showed that, without prior desliming of the pulp, 78 to 91 percent of the chromium could be recovered in concentrates of 90 percent or more chromite; two samples responded to similar treatment, resulting in concentrates of more than 80 percent chromite with recoveries of 85 and 89 percent chromium. One sample of mill products, subjected to severe weathering, required removal of the primary slime to obtain a concentrate of 65 percent chromite with only 75 percent chromium recovery.

Jan 1, 1960