Search Documents

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method's potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

By J. R. Allsup

In cooperation with the Division of Advanced Automotive Power Systems Development, Environmental Protection Agency, the Bureau of Mines studied a conventional spark-ignition engine as a prime mover for use in a hybrid system. The study involved both steady-state and transient engine operation with ignition timing, air-fuel ratio, exhaust gas recirculation, oxidizing type catalytic converters, engine speed, and power output as variables. Data were obtained from two 1971 model 350-cubic-inch-displacement engines mounted on engine dynamometer stands. When the hybrid engine was operated with an oxidizing catalyst at power output levels required for a 4,000-lb curb weight hybrid vehicle, carbon monoxide and hydrocarbon emissions could be reduced to approximately 2.0 grams and 0.3 gram per brake horsepower-hour, respectively. With exhaust gas recirculation, oxides of nitrogen emission levels could be reduced to approximately 1.2 grams per brake horsepower-hour.

Jan 1, 1974

By J. R. Wait, D. A. Hill

The feasibility of locating a buried vertical magnetic dipole source (horizontal loop) from surface measurements of the vertical and horizontal magnetic field components has been investigated by Wait (1971). , For sufficiently low frequencies, the magnetic fields have a simple static-like behavior, and a single observation of the ratio and relative phases of the vertical and horizontal field components is sufficient for location when the earth is homogeneous. However, when inhomogenieties are present, the surface fields will be modified, and source location may be more difficult. In order to obtain a quantitative idea of the surface field modifications, we consider a spherical conducting zone as a perturbation to the homo- geneous half-space. A rigorous solution for the buried sphere problem has been formulated by D'Yakanov (1959). Unfortunately, his solution is restricted to azimuthally symmetric excitation, and even then the solution is not in a convenient computational form. However, if the sphere is electrically small and is located at a sufficient distance from both the dipole source and the interface, the scattered fields can be identified as the secondary fields of induced dipole moments. The latter are equal to the product of the incident fields and the polarizabilities of the sphere. The details of the approach are given by Hill and Wait (1973). Wait (1968) has used this induced dipole moment approach for scattering by a small sphere above a conducting half-space. The method has the advantage that it is easily generalized to scatterers of other shapes for which both the electric and magnetic polarizabilities are known, such as spheroids (Van de Hulst, 1957). This concept has

Jan 1, 1973

Control dust generated during mining in salt mines. Approach A machine-mounted exhaust ventilation system which moves with the cutting machine from place to place was developed. The system captures the dust at the face of the heading and exhausts it downstream of the heading in the crosscut. This helps cause fresh air from the crosscut to flow over the machine operator's position, and aids in keeping the dust cloud close to the face. How It Works The system consists of (1) a circular intake hood with a 10-inch slot extending 250 degrees around the base, bolted to the gearhead; (2) 20-inch-diameter wire-wound flexible ducting to connect the intake hood to the fan (25 ft. is allowed sufficient slack for bar movement); (3) an industrial exhaust fan capable of generating 10,000 cfm with 13 inches water gage pressure at 1435 rpm; and (4) 150 ft. of collapsible 24-inch tubing for the exhaust duct which is de-played and returned In each heading by the cutter operator and/or his helper.

Jan 1, 1983

By C. F. Swab

A relatively innocuous halocarbon was investigated as a substitute for the highly toxic carbon tetrachloride in the approval testing of chemical cartridges. The vapor effluent of 1,1,2-trichloro-1,2,2-trifluoroethane from chemical cartridges is continuously monitored by a nondispersive infrared analyzer. Breakthrough times for the cartridges, using the halocarbon, can be equated to those of carbon tetrachloride, if multiplied by the factor, 1.49.

Jan 1, 1970

By Robert G. Yewen, Ronald S. Conti

Underground mines rely on alarm systems, such as stench gas, audible or visual alarms, pager phones, telephones, and messengers to warn miners of a fire or other emergency. These systems are often slow, unreliable, and limited in mine coverage. This report describes the evaluation of a wireless signaling and warning system for underground mines. This system is applicable to both coal and noncoal mines. The work was conducted by the National Institute for Occupational Safety and Health in cooperation with TeleMagnetic Signalling Systems (TSS) under Cooperative3Research and Development Agreement No. BOM-CRDA-6200-0119. A TSS wireless ultra-low-frequency electromagnetic signaling system was installed at the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. A commercial smoke sensor was interfaced to a remote portable transmitter, and the alarm of the sensor was used to trigger the central evacuation and paging transmitter system during experimental mine fires. The underground/surface receivers flashed cap lamps and activated remote devices, such as strobe lights, within 30 to 40 s after the encoded signal was received. Evaluation results showed full-mine coverage of the electromagnetic field and that the encoded signal was received at the farthest point underground and on the surface perimeter.

Jan 5, 1997

Develop a method for mapping planar geologic features in deep underground mines where the presence of metal interferes with compass readings. Background A fundamental problem of mapping planar geologic features in deep underground mines is the presence of metal (water and air pipes, track, equipment, etc.), which affects the accuracy and consistency of compasses. Present geologic mapping methods include use of transits or theodolites, both of which are cumbersome and time consuming to use. To complicate the mapping, process each planar feature must be surveyed, and if that feature is not apparent on the opposite wall, it cannot be mapped. Another method of mapping is to stretch a tape measure between two survey spads and place a string along a planar feature on one wall and out into the opening until it intersects the tape measure. This method, in addition to being time consuming, is also inaccurate. Because detailed mapping of planar geologic features deep underground involves many repetitive measurements, a quick, accurate, and reliable method for making such measurements was necessary. The geolaser was developed to make such measurements in deep underground mines where metal interferes with conventionally used compasses.

Jan 1, 1990

By Brian G. White, Theodore J. Williams, Jeffrey K. Whyatt

Detailed mapping and examination of the site of a large rock burst at the Lucky Friday Mine, Mullan, ID, demonstrated conclusively that damage was caused by a splitting and buckling failure mechanism initiated by separation of rock into layers along steeply dipping metamorphic shear foliation subparallel to the affected crosscut. The thin tablular layers then buckled into the crosscut from both sides. Rigorous control of the burst by these layers suggests practical measures for avoiding bursts in crosscuts in the future by repositioning and reorienting openings so that splitting and buckling are reduced or precluded.

Provide a lighter, smaller apparatus for more gently supporting electrical cable as it is raised or lowered in a well as compared with the conventional method of using a winch and pulley. Approach The conventional method of running cable into a well is to use a winch to pull the cable over a pulley located at the end of a boom placed over the well. This has the disadvantages of being bulky and of placing a concentrated strain on the cable at the point where it moves over the pulley. These disadvantages are overcome by using a "Chinese finger" cable grip assembly to hold and release a multiple conductor cable.

Jan 1, 1986

By H. C. Howarth

The preliminary tests referred to in this report wore made at the Bureau's Experimental Mine under the general supervision of G. S. Rice chief mining engineer, to determine whether rock dust way be used to extinguish or control mine fires. DESCRIPTION OF THE DUST USED The dust used for application by hand was made from draw slate taken from the Experimental Mine. This draw slate was crushed in a hammer-type crusher fitted with 1/16 inch by 2-inch slotted screens. A sizing test of the dust showed 96.5 per cent through 20 mesh, 69.4 per cent through 48 mesh, 46.2 per cent through 100 mesh, end 33.5 per cent through 200 mesh.

Jan 1, 1927

By B. D. Hanson

The U.S. Bureau of Mines has developed an interactive computer program which enables the user to identify the effect of cutting system changes on relative dust generation and forces for continuous miner drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. One or more of these parameters may be changed to determine their individual or collective effect on relative dust generation and cutting forces. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs.

Jan 1, 1989

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a longwall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) IS linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBV. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15 Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

To perform comprehensive economic evaluations on both existing and proposed mineral operations. Approach A comprehensive computer model was developed which is capable of evaluating the economics of an entire mineral recovery operation, including exploration, acquisition, infrastructure, mining, milling, smelting, refining, transportation, taxation, and return of and on capital. How it Works The MINSIM (MINe SIMulator) economic evaluation concept was developed by the Bureau of Mines in 1967. The initial versions used a continuous discounted cash flow rate-of-return (DCFROR) to measure the effect of changes in expected revenues and costs. Subsequent enhancements to the program have expanded and strengthened MINSIM, especially the addition of an option which determines total production cost (i.e., the commodity selling price that a mineral recovery operation would require in order to obtain a target rate of return), an expanded capacity for evaluating by-products from a mineral property, and significantly broadened taxation determining capabilities. The MINSIM computer program uses essentially the same procedures and calculations that are performed in a manual economic evaluation, although the program accomplishes its tasks much more rapidly and accurately, An experienced mineral economist may require a week to evaluate a single mining operation with the same detail and consistency provided by MINSIM in a matter of seconds of computer time.

Jan 1, 1983

By H. V. Makar

Ferrous fractions recovered from urban refuse were tested by the U.S. Bureau of Mines, U.S. Department of the Interior, to assess their character, composition, and response to detinning. This research was conducted as part of the Bureau's efforts to conserve mineral resources through recycling. Results from laboratory and pilot tests established the technical feasibility of detinning scrap recovered from household refuse. Detinned products containing less than 0.03 percent residual tin were produced. Concentrations of other residual elements were determined and compared with those in existing commercial scrap and with proposed specifications. Studies were extended to include evaluations under commercial conditions. Preliminary tests on 5-1/2 short tons of ferrous fractions revealed the need for adequate shredding to assure optimum metal-caustic contact and minimize retention of tin-bearing rinse solution in the final baled product. The washed metal product contained 0.06 percent residual tin. Subsequent melt tests showed a yield of 91.4 percent. Based on these studies, full-scale commercial demonstrations showed that detinned bales equivalent to No. 1 bundle quality could be produced in carload quantities. Up to 5 pounds of tin per gross ton of scrap is con-currently recovered during the detinning process.

Jan 1, 1979

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008

Develop a user-friendly, personal computer-based numerical modeling program that performs structural analyses of underground tabular deposits, making these readily available to the mining industry. Background When ore is extracted from an underground mine, the overburden weight is redistributed to unmined areas, recompacted gob zones, and artificial structures such as packwalls and/or cribs. This redistribution of stresses continually changes throughout the mining cycle and can be especially complicated when multiple-seam mining is involved. Numerical mine structural analysis methods provide a way of calculating the redistribution of overburden stresses and the resulting loading for any given area of an underground mine, thus enabling engineers to design safer and more productive mines. In 1973 Crouch and Fairhurst developed a mine structural analysis computer program called MINSIM. This computer program was based on the three-dimensional displacement-discontinuity approach, a subvariation of the boundary-element method. In 1979 Sinha expanded MINSIM's capability to provide an analysis of parallel multiple seams. Sinha called his program MULSIM. During 1984 and 1985, the Bureau of Mines upgraded and completely restructured MULSIM into what is now called MULSIM/BM.

Jan 1, 1990