Search Documents

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By R. Karl Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model, and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed that allows the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

Jan 5, 2007

By Susan B. Bealko

Mining provides a large part of the energy and raw materials that feed this Nation's economy. Copper pipe, concrete, and window glass serve as well known examples of the reliance on minerals in modern society. Less appreciated, but as important, are the hundreds of mined commodities that are an integral and necessary part of everyday products, ranging from medicines and computers to carpet and paper. Coal is a major portion of the country's energy mix today, as it will likely continue to be in a future hydrogen-based economy. The domestic mining industry also provides strategic minerals that are important for the Nation's security. The processes to recover these mineral commodities are among the most demanding and complex in an industrial society, and this inherently dangerous industry has historically had the highest risks of fatality and injury. The mining industry has been undergoing some trying and challenging times because of the recent mine disasters in the coal fields. These events have been alarming in light of the strong and encouraging safety record that has characterized mining in the United States for most of the past decade. While mining communities deal with their grief, mine operators, government regulators, and other safety personnel, set about trying to determine why these fatalities occurred. Subsequently, the mining industry is currently experiencing changes in legislation at an unusually rapid pace. The most recent regulatory changes are the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) and the temporary emergency standard for mine seals. The new mine safety laws call on the nation's mines to adopt certain procedures and safety technologies immediately, or as soon as they become commercially available. Putting all the provisions in place from these new laws is a major undertaking, and will necessitate strong collaborations and partnerships among mine operators, manufacturers, regulatory and research agencies, labor unions, and community groups. It is against this background that Prevention through Design (PtD) components for the Mining Sector are recommended.

Jan 1, 2008

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners? training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry(Morbidity and Mortality Week Report, 2001; NIOSH, 2002).Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year(NIOSH, 1999).

Jan 1, 2002

By A. D. Mah

Thermodynamic data on compounds of arsenic and sulfur were critically evaluated by the Bureau of Mines. Changes of standard enthalpy and Gibbs energy, and logarithms of the equilibrium constants were tabulated as a function of temperature for reactions involving these compounds.

Jan 1, 1982

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

Provide longwall operators with practical information and guidelines concerning mine design to reduce problems associated with the interaction of adjacent workings in multiple-scam longwall mines. Background The high productivity achieved by longwall mining demonstrates its potential to provide a substantial segment of underground coal production. Longwall mines produce more than 30 pct of underground coal, up from pct just 15 years ago. However, the continued growth of this mining method without appropriate multiple-seam planning may increase the cost and risk of mining. Research by the U.S. Bureau of Mines (USBM) indicates that 25 longwall mines (32 pct of the total number in the United States) have mining in adjacent coalbeds either above or below. About half of these longwall mines report some type of interaction problem with the adjacent workings, such as caving due to subsidence. Optimization of mine design factors is the best means for controlling interactions between operations in adjacent scams. To avoid higher mining costs, operators should focus on adopting practices and procedures that prevent and control interactions in multiple scams. The USBM, in an effort to improve longwall mine planning, has been investigating multiple-seam longwall design and development.

Jan 1, 1994

By Charles P. Lazzara, Charles D. Litton, Frank J. Perzak

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 1991

Eliminate accidental tramming of a cleanup tractor. Approach A switch was installed in the operator's seat cushion to pre-vent the cleanup tractor from tramming without an operator in the driver's seat. How It Works The operator must be seated, and the Forward/Reverse Switch (that controls tramming direction) must pass through the NEUTRAL position before the vehicle will tram. See Figure 1. A pressure-sensitive seat cushion switch, a solid-state relay, and a double-contact relay were added to the control circuitry of an S & S BMUAT -88 cleanup tractor to create this tramming interlock. The weight of the operator on the cushion closes the seat cushion switch (Figure 2, A). This activates the solid-state relay (B), which completes the initial circuitry. Moving the For- ward/Reverse Switch (C) to NEUTRAL energizes the coil in the double-contact relay (D) and closes both contacts. One contact completes a sustaining circuit which keeps the double-contact relay energized. The second contact transfers power to the remaining contacts within the Forward/ Reverse Switch. These circuits are shown in greater de- tail in Figure 2.

Jan 1, 1978

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

THIS PROGRAM TRANSFORMS FREE FORHATED BRANCH DATA INTO A FORMAT SUITABLE FOR INPUT TO THE PENNSYLVANIA STATE UNIVERSITY MINE VENTILATION SIMULATOR (PSU/HVS 1. BRANCH RESISTANCES ARE ASSUMED TO HAVE BEEN ALREADY CALCULATED, IIOWEVER THIS PROGRAM CAN BE EASILY MODIFIED TO HANDLE THE ADDITIONAL INPUT DATA REQUIRED FOR RESISTANCE CALCULATIONS IN THE PSU/MVSO THE PROGRAM IS WRITTEN IN FORTRAN IV WITH WATFIV.

Jan 1, 1977

By V. A. Marple, K. L. Rubow

"Filter samplers are one of the simplest methods and, in some instances, one of the only methods that can be use to obtain samples of particulate matter suspended in a gaseous medium. Once collected, particles are normally analyzed directly on the filter by gravimetric, chemical or microscopic techniques. However, it is sometimes desirable to resuspend the particles in an airstream for analysis. This would be the case if the size distribution of the particles were to be measured using one of many particle sizing techniques such as inertial classifiers, optical particle counters or the TSI Aerodynamic Particle Sizer CAPS).A ·technique has been recently developed whereby one can resuspend particles from filter samples in an airstream. The technique has been used for the resuspension of coal dust from filters. The resuspended particles were then introduced into the APS. This development was necessary since an APS can not be taken directly into an underground coal mine. For this application, particle samples are collected on membrane filters in the underground mines. The mass concentration of the particles determined through gravimetric analysis. The particle size distribution was tl1en determined by resuspending the particles and passing them through a TSI Aerodynamic Particle Sizer (APS). Excellent agreement has been obtained between the size distribution directly measured underground with a cascade impactor and that measured from the resuspended particles. For this experiment, an open-faced filter sampler was placed adjacent to the cascade impactor in the n1ine. The particles collected on the filter were resuspended in the laboratory and Measured with the APS.A venturi aspirator is used in the apparatus developed for resuspending the particles. The venturi has a small diameter capillary tube placed in the venturi throat. High velocity air flow is passed through the venturi, thereby, creating a low pressure region at the exit of the capillary tube. The low pressure draws air through the tube. The filter with deposited particles is located at the inlet to the capillary tube where the air flow into the capillary resuspend the particles. Once airborne, the particles are deagglomerated as they pass through the high velocity air flow in the venturi throat."

Jan 1, 1989

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

By Fred C. Turin, Sean Gallagher, Kim M. Cornelius, William J. Wiehagen

An important part of initiating a site-wide ergonomics evaluation process is prioritizing jobs to be analyzed. While injury data is important, other factors such as worker discomfort and physical exertion requirements, should be considered. This paper describes the use of four sources of data (injury records, the Nordic Standardized Musculoskeletal Questionnaire, supervisor interviews, and management concerns) to prioritize jobs for ergonomic analysis. The approach described integrates the four sources using a decision matrix to prioritize jobs for ergonomics analysis.

By S. R. B. Cooke, J. Bruce Clemmer, Will H. Cognill, F. D. DeVaney

"INTRODUCTION The domestic production of potash has made rapid strides in the past 4 years. In 1929 the United States produced 109,820 tons of potash-bearing material, equivalent to 61,590 tons of pure potash (K20). In 1933 to this had increased to 331,110 tons, containing 143,378 tons of potash, due chiefly to the development of the potash deposits near Carlsbad, N. Mex. The potash ores of that district occur at a depth of about 1,000 feet and as mined consist of a mixture known as sylvinite containing about 40 parts of sylvite (KC1) and 60 parts of halite (NaCl). By careful mining the extraneous material does not amount to more than 2 or 3 per cent. Such ore was used in the experimental work here reported.The usual chemical method for the recovery of potash from sylvinite, while efficient in the production of pure potassium chloride, requires,expensive equipment and is costly to operate. It occurred to the Bureau of Mines that ore-dressing methods, which have been applied to other nonmetallic minerals, might be adapted for the production of a grade of potash suitable for the fertilizer industry. After preliminary study by the Bureau of Mines showed that ore-dressing treatment was possible the investigation was extended under a cooperative agreement between the U.S. Bureau of Mines, the Potash Company of America, and the Missouri School of Mines and Metallurgy, Rolla, Mo.ACKNOWLEDGMENTSAcknowledgment is here given for valuable assistance in the laboratory of R. G. O'Meara, assistant metallurgist. U.S. Bureau of Mines, Tuscaloosa, Ala. who was on detail at the Rolla station during the early work; by E. W. Gieseke and Albert Ollar, temporarily employed by the Potash Company of America; and to N. H. Lenz, an engineer temporarily assigned to the station."

Feb 1, 1935

Improve mine refrigeration system efficiency while providing free electrical energy to mines. Approach Convert the potential energy of incoming mine water falling down long vertical shafts into electrical energy by means of a turbine-generator system located at the bottom of the mine shaft. How it Works Converting the energy of falling water into useful work is a well-developed engineering concept. Water flowing down long vertical pipelines into deep mines develops high pressure that can be used to operate a turbine-generator system at the bottom of the pipeline. A thermal energy recovery system of this type offers three advantages: 1. In systems without turbines, the potential energy of the water is converted to heat. The water temper-ture will automatically

Jan 1, 1985

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

Provide an inexpensive, simple means of supporting highly yielding ground In underground mines. Approach The Bureau of Mines developed a high capacity support post made from standard steel pipe which, when using a 60-inch post configuration, has a 45-ton capacity and a yield length of 24 inches. How It Works The post mechanism is a three-piece unit consisting of a top and bottom leg (made from standard steel pipe) and a separate foot bracket. During installation in the mine, the bottom leg is placed on a relatively flat surface on the mine floor and the top leg is placed over it until its flared end contacts an expansion ring attached to the bottom leg. As the roof and floor converge, the flared end of the top leg is forced into the expansion ring, causing the walls of the top leg to be deformed radially and along the axis. The mechanism will yield until the unit bottoms out after about 24 inches of yield.

Jan 1, 1987

Improve the dust control effectiveness of dry collection systems on surface coal mine drills. Approach Use a dust pelletizer to convert the respirable dust particles discharged by the dry collector into dust pellets that present no health hazard. Background Blasthole drills are well-known sources of respirable dust that can contain significant amounts of quartz. The drills frequently use a dry cyclone-filter type collector that can obtain dust reductions theoretically greater than 95 pct. However, surface mine drills using dry collectors typically have three major dust sources that significantly reduce the overall effectiveness of the collection system: (1) the dust collector dump cycle, (2) drill shroud leakage, and (3) leakage around the drill stem seal in the drill table.

Jan 1, 1989