Search Documents

By A. T. Iannacchione

Synopsis Underground stone mining Is an emerging sector of the U.S. mining industry. As this expansion takes mines under deeper cover, and as more efficient mining methods are utilized, effective stone pillar design methods will become even more Important. Current design practices are examined and a discussion of safe mine layouts is presented as a first approach towards weighing the demands for increased production against increased risk. Risks to underground stone-mine workers include rib Instabilities, pillar failures and roof falls. Seventy-two stone-mine pillar designs were examined. Pillars with width to height ratios of less than 1.5 appear more likely to fail when subjected to excessive stress levels. When width to height ratios fall below 1.0 defects in the pillars, such as through-running discon¬tinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties and orientation are also important determining factors in pillar strength. During the past three years the number of active underground stone mines in the U.S.A. has ranged between 90 and 100. This number is expected to increase as the crushed stone industry responds to growing demands for its products.1 As more of the industry moves to benefit from the advantages of underground mining production from underground stone mines is expected to increase above its current level of approximately 66 000 000 r/year. Parker2 identified four advantages of underground mining operations: (1) surface developments, zoning laws and environmental concerns are often less of an issue; (2) stripping and restoration requirements are eliminated; (3) additional reserves are often available beneath the quarry floor, under pit slopes or under an adjoining property; and (4) space is created for secondary use. Underground mines enjoy the added benefits of work in a constant underground climate, rather than in the variable surface climate, minimization of community concerns by placement of the crushing, sizing and stowing operations underground and reduction of surface vibration concerns through smaller blasts. The drawbacks of underground mining include added health and safety hazards for the stone miners, whose health can suffer from increased exposure to falls of ground, airborne contaminants and fog in large underground openings. Injuries from falls of ground in stone mines have occasionally exceeded the incidence rates for other mineral resources mined underground. 3 Existing underground stone operations, by comparison with stone operations a decade ago, mine more stone at a faster rate and with larger equipment. Because of high demand mines face increased pressure to yield more stone per production blast. A majority of the miners use the V-cut blasting pattern, which limits the depth or pull for each shot to about 4 m. Therefore, to produce more stone, either the mines must work more faces or existing faces must be enlarged. The enlargement of underground openings poses problems in the maintenance o€ strata stability, First, the widths of the mine entries partially control the amount of sag or deflection that any given roof beam can withstand before failure. This deflection can take pi ace quickly after an opening is excavated or much later as weathering processes form additional, thinner beams. Because increased deflection increases the potential for roof beam failure, there is a limit to how wide a room can safely be made. These limits depend on local geological and stress conditions and, to some extent, the cost effectiveness of roof-bolting. Given these room width limitations, underground stone mines have placed more attention on expansion of production through benching where mining thicknesses permit. The heights of rooms partially control the strength characteristics of adjacent pillars: as the room height increases for a given pillar width the pillar width-to-height ratio (w/h) decreases. In general, stone pillars are very strong, but when the width-to height ratio diminishes the potential for pillar rib instabilities and pillar failures increases (see Fig. 1). [ ] In the underground environment the desire to utilize wider rooms, higher benches and multi-level mining results in the potential for unstable ground conditions. Although the number of failed pillars is currently very low, the potential for additional failures will grow if more slender pillars are developed, especially under deeper cover, with wider mining sections and in multi-level operations. It should also be noted that the passage of time acts to decrease the strength of many existing pillars. An examination of current design practices

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

1, Introduction This report is submitted in fulfillment of the requirements of USBM Contract No. J0255017, "Development of Emergency Escape Systems Guidelines for Underground Metal and Nonmetal Mines" Under this contract the history of past mine fires was studied. Representative metal and nonmetal mines were surveyed and escapeways, refuge chambers, life support, and emergency hoist requirements were studied to determine the problems in complying with the proposed regulatory standards and their enforcement by MESA Mine Inspectors. In addition, a computer program was written to evaluate mine evacuation performance. The completed program is included in the appendix. 1. 1 Historical Review of Metal and Nonmetal Mine Fires Early records of mine fires are poorly documented because there was no statutory provision for reporting fires to the Bureau of Mines. The survey of representative mines during the course of this contract indicated that many small fires still go unreported even though they are now required to report all fires A recent report survey approximately 80 disasters in metal and nonmetal mines, (6 ) Table I is a summary of some of these fires. Historically most metal and nonmetal mine fires have been caused by electrical problems. Spontaneous combustion and the use of welding equipment are the other major causes of mine fires(14) Although not documented, many mine personnel agree that 30 percent to 40 percent of underground metal and nonmetal mine fires have their origin from cigarettes and other smoking related materials. The number of fires related to spontaneous combustion is decreasing and equipment fires are on the increase. The reduction of spontaneous combustion fires can be attributed to the use of sandfill in more mines and the increase in equipment fires to the increased use of LHD equipment.

Jan 1, 1976

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40° F (-40°C) with 75% No. 1125% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34" C) with 75% No. 2/25% RO, and at 0° F(-18° C)with 50/50. Reference detonation velocity tests were conducted in 1.4" (3.6 cm) diameter steel pipe at 70°F (21°C) on No. 1 diesel ANFO (94-6), giving an average value of 9722 ft/s (2964 m/s). Comparison tests showed good ANFO performance at low temperatures. Blended fuel ANFO (75% No. 1/25% RO) mixed, loaded, and tested at -40°F (-40°C), produced an average velocity of 9247 Ws (281 8 m/s). A 50/50 blend gave a velocity of 8083 Ws (2464 ds) at -20°F (-29°C). Based on these results, a practical field method has been developed to help evaluate whether a specific oil blend will mix properly with AN at a low ambient temperature. This method will help to promote the safe and reliable use of RO ANFO at low temperatures, with adequate performance.

Jan 1, 2008

By L. C. IlsLey

It is most unfortunate that a few must often suffer , and perhaps die , that many may benefit from a fuller appreciation of the dangers surrounding mining operations , and the proper use of safeguards designed to offset these dangers . This has been the case during the last few months in the anthracite field , where several explosions , resulting in burnings and fatalities , were undoubtedly caused by the use of defective or improperly assembled flame safety lamps . Had this same lack of understanding regarding the proper assembly of this safety device , and had the same indifference on the part of the user in keeping the lamps locked at all times and in proper condition , been permitted in a region where the coal dust was explosive , a terrible disaster would surely have resulted . In nearly every coal -mining country , including the United States , the Davy and Clanny type of lamp has been superseded , and rightly so , by some kind of bonneted lamp . Bonneted lamps , especially of the naphtha type , while much safer than the unbonneted , have more parts and need more care in assembling . For this reason the burden of responsibility for their being properly assembled rests with the lamp man ; therefore , it is extremely important that only competent , conscientious men be given this work .

Dec 1, 1921

By B. Olson, V. A. Marple, D. J. Radet

"Gravitational forces have been found to be an important factor in defining the particle collection efficiency curve of inertial impactors for large particles. In general it was found that if the parameter G = gW /V 0 2 (g is the gravitational acceleration. w is the nozzle diameter and V 0 is the average fluid velocity at the nozzle throat) in greater than 10-3 the efficiency curve would shift to lower panicle sizes. No effect could be seen for lower values of G.IN'IRODUCTIONInertial impactors have long been used as classifiers for airborne particles. By proper design of the nozzles and flow rate it is possible to classify particles with a fairly sharp cut in the particle size range from approximately .02 µm to 50 µm. Because of inertial impactors wide usage they have been extensively studied calibrated and evaluated. Most of these studies have been experimental calibrations of single stages using monodisperse aerosol particles. However, due to impactor simplicity. i.e. a jet of particle laden air impinging upon a flat plate with large inertia particles crossing the streamlines and impacting upon the plate the impactor also lends itself to theoretical evaluation.The most comprehensive method for analyzing impactors theoretically is to use finite difference solutions to the Navier-Stokcs equations and solve for the velocity components and pressure at node points of a grid placed over the area of interest. Using iteration and relaxation techniques the value of the velocity vectors can be determined at these node points with good accuracy. Once the velocities arc known, theoretical particles of known size can be placed into the now field and their trajectories determined by analyzing their equation of motion using numerical methods.Rader and Marple (1985) have performed theoretical analysis on impactors and have included such factors as Ultra-Stoksian .drag and the physical diameter of the particle in their analysis. However, even with these· factors included, there appears to be discrepancy · between the experimental and theoretical results when the particle size is larger than approximately 4 or 5 µm. One possible reason for this discrepancy could be the effect of gravity on the particle as it passes through the impactor. Therefore, a program was initiated to study the effects of gravitational forces on the collection· efficiency of particles in impactors. The results of that study arc presented here."

Jan 1, 1990

By F. C. Gregory

"The ""safety bonus"" in metal mining is a sum in addition to the regular wage, paid to foremen or bosses for keeping the accident rate down to a specified minimum. It has been used with success for some time by certain companies as a regular part of their safety work. It is desirable from the employer's point of view in that the desired results in accident reduction must be accomplished before the bonus is earned; and from the standpoint of the recipient, in that he receives a reward for the additional effort which he has put forth in order to earn the bonus.While this paper relates to the safety bonus as applied in the metal mining industry, the bonus system discussed herein will apply equal well to coal mining, oil-field work, and other mineral industries.Various estimates have been made as to the percentage of accidents that can be prevented through physical safeguards, adoption of safe working methods, and other safety measures which can be initiated and carried out wholly through the management or the safety department. This percentage will always be a vari¬able according to the local plant and conditions. But all who have been engaged in accident prevention agree that such work alone cannot bring the accident fre¬quency down to where it should be, and that it is very necessary to work directly with the workmen, in an effort to make each individual do his share in making the work safe. In this latter phase of the work, the boss who has immediate super¬vision of the men is the one who can do the most, since he is in daily and frequent contact with the men while they are at work. In the metal mines, the shift and stope bosses are the key men; in the oil fields, the ""tool-pushers"" or sub-foremen, and the same applies to all industries. So it becomes necessary to keep these sub-foremen constantly interested in accident prevention, both because they are in personal touch with the men and because they are responsible for production and hostile to any plan which they think will interfere with their output. In large organizations it is the shift boss who represents the company and its policies to the man on the job."

Jun 1, 1924

By Richard J. Mainiero

The Bureau of Mines has developed a prototype nonincendive explosive rock-breaker charge that can be fired unconfined in underground bituminous coal mines without the danger of igniting a flammable atmosphere that might be present. At present, unconfined shooting in underground coal mines is prohibited, but there are situations where the use of such shots would yield an overall improvement in safety. The charge consists of 1-1/2 lb of permissible water gel explosive in the form of a short cylinder 7 inches in diameter and 7/8 inches high, surrounded by a 1 1/2-inch-thick layer of damp salt, and encased in latex rubber reinforced with cheese cloth. The latex rubber housing provides a charge package that is strong enough to resist rough handling yet is pliable enough to conform to an irregular stone surface. A charge of this shape was found to be more effective at breaking rock than charges with lined or unlined cavities. Incendivity tests in a gallery have shown that the prototype charge will not ignite a flammable methane-air atmosphere when fired. Rock- breaking tests made with limestone boulders indicate that the charge will satisfactorily break stone slabs weighing 1 to 2 tons, and that two or more charges might be effective for slabs weighing up to 10 tons. In cooperation with the Mine Safety and Health Administration (MSHA), a test protocol for the certification of these charges as "permissible" for use in flammable atmospheres is being developed.

Jan 1, 1982

A PRELIMINARY PROGRAM, dated April 25, 1974, was prepared for Development Engineering, Incorporated (DEI) on research and development laboratory, field and other engineering studies for the disposal of retorted oil-shale materials. This PRELIMINARY PROGRAM included a discussion on the peculiarities of the retorted shale materials to be investigated and a discussion of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The PRELIMINARY PROGRAM was divided into eight work phases as follows: I -- Program Development II -- Exploratory laboratory tests on old USBM retorted shale III -- Laboratory tests on pilot plant retorted shale. IV -- Laboratory tests on retorted shale from the semi-works plant and field test plots and ponds. V -- Field compaction tests. VI -- Infiltration pond tests VII -- Bureau of Mines special tests.

Jan 1, 1975

As a basis for recommendation and for instruction of bureau engineers the considered opinion of the bureau is expressed in "decisions" of its Mine Safety Board, approved by the Director. Ten of these decisions were discussed, in Information Circular 6091.3 Decision No. 11, approved by Scott Turner, Director, on February 28, 1929, is as follows: "In the interest of safety, the Bureau of Mines, Department of. Commerce, recommends that in coal mines, haulage and (or) hoisting be kept in intake air as far as possible." As in the case of previous mine-safety decisions, the subject matter covered by this decision has frequently come to the attention of the Bureau of Mines through the reports of its mining engineers on explosion disasters and in accident-hazard investigations.

Jan 1, 1929

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

In the interest of safety ii: coal mining, the Bureau of Mines recommends: That all active underground coal mines, whether working or idle, have one or more fans in continuous operation. The capacity and installation shall be such that the entire mine workings are adequately ventilated at all times. Main fairs shall be located on the surface in fireproof housing offset from the line of any mine opening. The housing shall be provided with ample pressure-relief doors or other devices easily opened by the force of an explosion. The installation shall permit prompt reversal of air flow. For mines that liberate gas, the fan shall have at least two independent sources of rower immediately applicable. Ventilation of underground workings in coal mines is needed whether or not explosive gas is present. Natural ventilation is unreliable and often uncontrollable. Main fans should be on the surface; if they are in the mine, fire or explosion may make access difficult or dangerous and render the installation inoperative.

Jan 1, 1939

By F. J. Bailey

"In the fall of 1919, the U.S. Bureau of Mines began an inquiry as to the possibility of utilizing airplanes in conjunction with its rescue work, for quickly transporting engineers and oxygen rescue-apparatus to mine disasters.It was realised that this proposed use of airplanes has serious limitations, and if it were feasible, that the Bureau would have to rely on the cooperation of the established aviation fields of the U. S. Air Service for furnishing airplane service. Therefore Van. H. Manning, Director of the Bureau of Mines, under date of October 28, 1919, wrote the Director of Air Service outlining the rescue and first aid organization of the Bureau, the location of headquarters of district engineers, the distribution of safety cars and stations, and other essential details, and asking whether the Air Service could cooperate with the Bureau in the event of serious mine disasters. Major-General Charles T. Menoher, Director of Air Service, responded that the Air Service would be glad to cooperate insofar as possible, and designated those Air Service stations nearest the district engineers' headquarters, which might be best able to assist.The Bureau of Mines has ten mine rescue cars and eight mine safety stations distributed throughout the mining regions of the United States. The cars are each equipped with sets of oxygen mine-rescue breathing-apparatus and first-aid supplies. The car personnel consists of a mining engineer, surgeon, foreman, first-aid miner, clerk and cook. A foreman miner is in charge of each station and at five of the eight stations are mine safety trucks. The work of the cars and stations is two-fold; (1) Assisting in rescue and recovery work at mine disasters, and (2) training miners in mine rescue and first-aid methods, and in investigations looking to prevention of mine accidents. The country is divided into nine safety districts, with nine district engineers in charge."

Apr 1, 1920

By D. B. Dow

The transportation of any commodity which is actually or potentially a source of fire or explosion, has been made safe, insofar as humanly possible, by rigid requirements as to inspection mechanical safety devices, and by printed labels. For the most part these precautions have been sufficient. This is evident when it is considered that in the thousands of instances in which commodities with a great fire risk have been transported, few disasters have occurred. This paper deals with the recent gasoline explosion which occurred at Memphis, Tennessee. At 7:50 a.m. January 24, 1921, vapors from a tan: car of gasoline became ignited and resulted in a blast that killed eleven people and badly injured nineteen others. Probably forty or fifty men, women, and children received slight injuries from falling debris or from burns. The explosion wrecked an oil plant, leveled a block of frame buildings, and broke window panes within a radius of five blocks.

Feb 1, 1921

By John Gross

The Alaska Station of the Bureau of Mines has recently conducted tests on two tailings from black sand which had been treated previously at the Station. The results of this previous treatment have be on given in a paper entitled "Recovery of Gold from Black Sand by Classifier Concentration." The gold in these tailings was intimately united with quartz, and was so finely divided that it could not be detected with the naked eye, nor even by P&nn ing unless the material was ground. Its fineness is further shown by the assºy result, which reported only lz per cent of the gold content as "metallics", Wºorea's the assay of the original sand reported 36 per cent of the gold as "metallics." The fact that the gold was in such fine particles, closely united with quartz, precluded further recovery by amalgamation without grinding. On the other hand, the small content present, as well as the lack of grinding appliances at the placer mines of Alasia, made it necessary that the material be cheaply handled if at all. With these facts in mind the experiments described below were undertake.n.

Oct 1, 1920

By Thomas V. Falkie, R. Venkataramani

Table

Jan 1, 1972

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936