Search Documents

By A. N. Fried

One of the important problems confronting oil producers in appraising the possibilities of secondary recovery in many California fields is the effect of viscosity on oil recovery by water flooding. In January 1954 there were 554 fields and/or pools, in the State, that produced 1 million barrels daily, and 138 of these pools produced approximately 267 thousand barrels daily of heavy crude oil having gravities below 200 API. Many of these fields are nearing the end of their primary economic life and still have high residual-oil saturations, a favorable factor in water flooding. The crux of the problem is whether or not enough oil can be recovered from these fields by water flooding to make the operation economically successful. Some experiments on the relationship between viscosity and oil recovery have been made by other investigators, but in most instances the viscosity of the oils used in the experiments was lower than the viscosity of the oils found in many of the heavy-oil fields in California. A study was undertaken, therefore, to determine the relationship between oil viscosity and recovery over a wider range of viscosities and to compare the experimental results with those predicted by theoretical calculations.

Jan 1, 1955

By E. G. King

Sodium-aluminum and calcium-aluminum silicates are important rock-forming minerals. While many of them are of only theoretical interest, several are of practical importance--as ceramic raw materials and as potential future sources of aluminum. Heretofore, thermodynamic data for these minerals were incomplete; and in many instances missing data were difficult to estimate reliably. This has seriously hampered thermodynamic calculations pertaining both to the natural formations of these minerals and to their decomposition in sintering and fluxing reactions. This paper reports the results of the Federal Bureau of Mines measurements of low-temperature heat capacities of four crystalline silicate minerals--dehydrated analcite (NaAlSi2O6), hexagonal anorthite (CaA12 Si208), lawsonite (Ca2Al2Si2080?2H20), and leonhardite (Ca2Al4Si8C24?7H2O). It augments previous similar measurements of related minerals, which were summarized recently.4 The measured heat-capacity data were used to derive entropy values for the four minerals at 298.15° K. Some relations between these entropy values and those of other similar minerals were discussed. These relations illustrate the difficulty of estimating entropy values of tertiary (or higher) silicates.

Jan 1, 1961

Between 1985-1986, the Bureau of Mines reviewed the mining history and minerals information for areas in and near the San Isabel National Forest to appraise the mineral resources present and determine the types of deposits, and their location in the Forest, that could be mined economically if sufficient demand and metal prices existed. The two major metallic deposit-types that are of national mineral resource significance within the Forest are stockwork- molybdenum (with tungsten and tin) and carbonate-replacement zinc-lead-silver deposits. Historically, small gold placers, gold-quartz veins, silver-quartz veins, skarn iron and copper deposits, volcanogenic copper-zinc-precious metal deposits, and base- and precious-metal veins have been mined. Barite, carbonate rocks, gypsum, other non-metallic deposits, and pegmatites, have also been mined. Sand and gravel, present in large volumes, occurs along and has been mined outside the Forest along the upper Arkansas River valley. Turquoise and gemstones are present in small amounts and are of interest to collectors and jewelers. Geologically, sediment-hosted uranium and copper are present in small occurrences but no resources have been identified. Geothermal resources are related to the Rio Grande rift which parallels the central part of the Forest. Four hot spring areas are present - two of these are within the Forest. Because of the low power requirements of the region, and the presence of other generating facilities, these geothermal resources have had only limited local use. Evaluation of mine models that may be found in the region show that base-metal deposits require a high precious-metal component to be economic. Although molybdenum can be produced at economically competitive prices, there is little demand for the product. Capital costs to start new molybdenum mines would be very high and it is not likely that new mines will be put into production in the near future.

Jan 1, 1989

By John C. Edwards

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization-and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor's alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m-l for smoldering and flaming coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m-l, whereas the optical smoke detectors showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 2010

By William J. Campbell

This analytical method development and evaluation was undertaken by the Bureau of Mines to provide accurate determinations of eight minor elements in low-alloy steels prepared from ferrous scrap. Fluorescent X-ray spectrography was the principal method investigated. Confirming analyses were made by conventional instrumental and chemical methods. All X-ray data were processed by a timesharing computer. No corrections were found necessary for inter-element effects or overlapping spectral lines. Concentrations were calculated from the least-square fit of a linear calibration equation derived from measurements on three sets of standard steels. These studies show that X-ray spectrographic analysis of lathe-finished surfaces provides accurate determinations of aluminum, copper, chromium, manganese, nickel, phosphorus, silicon, and tin.

Jan 1, 1973

By Raja V. Rarnani, Robert L. Frantz

"Mining is one of the oldest of human occupations. The awareness of occupational illnesses associated with mining, even in ancient times, is evident from the writings of Hippocrates (460-370 BC), Pliny and Elder (AD 23-79), and Galen (AD 131-210). Georgius Agricola (1494-1535), in his De Re Metallica, refers to the diseases of miners and the need for their control through good planning and operating practices and responsible management (Schwerha, 1989). Coal workers' pneumoconiosis (CWP), often called Black Lung disease, is an occupational disease which results from inhalation of coal mine dust which usually contains relatively small amounts of free crystalline silica.A pneumoconiosis is best defined as the accumulation of dust in the lungs and the tissue's reaction to its presence [Lapp and Castranova, 1993]. Silicosis is the name given to the fibrotic disease of the lungs caused by the inhalation of dust containing silicon dioxide, primarily in the free crystalline form. Silicosis is the older and more well known of these mineral pneumoconioses. In contrast, CWP was not recognized as different from silicosis until the pivotal work of Collis and Gilchrist [1928].The U.S. Bureau of Mines (USBM) still regards worker exposure to respirable aerosols in mines as the most serious health problem in mining [USBM, 1994]. The National Institute of Occupational Safety and Health (NIOSH) is considering recommending a reduction in the standard for occupational exposure to respirable coal mine dust from 2 mg/m3 to 1 mg/m3 [NIOSH, 1993]. The Mine Safety and Health Administration (MSHA) may require new criterion for sampling procedures in the mine that would evaluate the ambient dust concentration in the mine atmosphere based on a single sample, instead of the current practice of averaging five samples (MSHA, 1992; Ramat* 1993). Several high-production longwall mining faces currently have extreme difficulty meeting the existing dust standards, and some already operate at reduced production levels to achieve mandated levels [USBM, 1993]. The importance of adequately protecting the miners from high concentrations of coal mine dust, as well as of reducing the incidence and severity of the Black Lung disease, cannot be overemphasized. The importance stems, first and foremost, from the humanitarian viewpoint and, second, from the perspective of the overall welfare of the coal industry.The histopathologic hallmark of CWP is the coal macule (Balaan, Weber and Banks, 1993). Autopsy or open lung biopsy reveals the coal macule to be an amorphous mass of coal particles, dust-laden pulmonary macrophages, reticulin, and collagen. No pathognomonic signs or symptoms identify workers with CWP. A CWP diagnosis requires that the worker experienced the appropriate dust-exposure setting (e.g., underground coal mining) and duration (usually 10 years or more) and, has the characteristic chest radiograph. Based upon the International Labour Organization (ILO, 1980) international classification, pathologists and radiologists have established case definitions for characterizing the pathology and the appearance of CWP on chest radiography (Weeks, 1993). CWP appears in two principal forms: simple, with small opacities, and complicated, with opacities larger than 10 mm in diameter. For all practical purposes, diagnosis of CWP in the living miner is wholly dependent upon the chest radiograph interpretation."

Jan 1, 1995

By W. H. Oppelt

A lignite from west-central North Dakota (Mercer County) was dried by the Bureau of Mines by the Fleissner process at saturated steam pressures to 1,500 pounds per square inch absolute (p.s.i.a.). Normally, the process is operated at pressures of 200 to 370 p.s.i.a. At the highest pressure the temperature of the saturated stearn is 596° F. The purpose of the investigation was to evaluate the influence of very high stearn pressure and temperature on moisture removal, steam consumption, and physical and chemical characteristics of the dried lignite. Two drying cycles were used: A normal cycle, corresponding to previously established standard time requirements, and an accelerated cycle, wherein time requirements were determined by boiler capacity and handling speed. Blank tests to determine stearn requirements for heating the empty autoclave were performed for each cycle and each test condition. Moisture removal, final moisture content, net steam consumption, and size stability of the dried lignite were determined.

Jan 1, 1959

Develop and evaluate a mechanical position and heading system (MPHS) that provides information about underground mining machine position and heading to aid in the remote positioning of mining machines during face maneuvers. Background While great improvements have been made in mineworker safety, progressive technology continues to create a safer, better working environment for miners by keeping them away from the dangerous face area. In maintaining such high standards of safety, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A key component of computer-assisted operation is a guidance system. Since there are no guidance systems on any commercial continuous mining machines, the Bureau itself developed and tested the mechanical position and heading system (MPHS). The MPHS is based on linear position transducers (LPT's), and operates on principles of triangulation to provide machine position (xy coordinate), and orientation in the xy plane (yaw or heading). These data are needed in order to keep the continuous mining machine in proper alignment before and during the cutting cycle. The MPHS theory development is in three parts: characterize the sensors used and their configuration; select and define the navigation reference frames; and derive a closed-form solution for determining the position and beading from sensor information. Application of the MPHS theory required the development of hardware, software, and system interfaces.

Jan 1, 1992

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By Victor E. Kral

The Modarelli iron deposit , formerly known as the Requa iron deposit , is 44 miles by road south of Palisade , Nev . , on the Southern Pacific and Western Pacific Railroads . Construction of 10 miles of new road, which is necessary in case the property is exploited , will reduce this distance to about 28 miles . The deposit was discovered in 1905 , and patent was obtained in 1907 . The present owners obtained title to the property in recent years by paying the delinquent taxes . There has been no production . The ore deposit is a replacement of a Tertiary volcanic believed to be a rhyolite . Except for evidence of slight shearing , the deposit has no apparent structure . Hematite is the principal ore mineral ; it is fine-grained and is associated with very fine-grained apatite and unidentified minerals assumed to be alteration products of residual rhyolite minerals .

Feb 1, 1947

By C. M. McKinney

Bureau of Mines routine crude-oil analyses of 42 samples from 37 fields in the major producing areas in Mexico are presented in this report. Table 1 includes information on the source and general characteristics of each sample. Table 2 gives a summary of analytical and computed data. A map (fig. 1) shows approximately where the samples were obtained. ACKNOWLEDGMENTS Grateful acknowledgment is made to Alfonso Barnetche, manager of production, and Ing. Francisco Inguanzo, assistant manager of production, both of Petroleos Mexicanos, who supplied the crude-oil samples and furnished information concerning their sources.

Jan 1, 1960

By E. D. Gardner

The Bureau of nines, in cooperation with the mining companies of the Southwest, is conducting an investigating to ascertain the safest and most economical explosives to use in metal mines, and to ascertain the best methods of blasting under various conditions. A part of this investigation has been a study of drilling and blasting drift rounds in metal mines. This paper covers one phase of work on drift rounds and discusses the methods of loading the individual holes of the rounds. The blasting tests, on which this paper is based, were made at the Copper queen Branch of the Phelps Dodge Corporation at Bisbee, Arizona.

Jan 1, 1927

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951

By Michael D. Balen

This Bureau of Mines open file report is one in a series of reports written about the Valdez Creek Mining District (VCM D) as a result of the continuing Bureau of Mines mining district evaluation program. This report presents the results of order-of-magnitude mining feasibility studies. The mining feasibility studies were conducted for mineral deposit models that were based on real and hypothetical deposits that occur in the VCMD. A total of 6b mine models were developed for application to the mineral deposit models. The goal of the feasibility study was to determine the monetary value per unit of minable ore that would cause the simulated cash flow for each of 66 mine models to achieve certain pre-defined rates of return for the invested capital.

Jan 1, 2011

By Richard W. Lewis

Domestic production of greensand (glauconite) increased 15 percent in quantity and 13 percent in value compared with that of 1964. Since only two firms were in operation, statistics on production and sales for the year are not reported in order to avoid disclosure of individual company confidental data. The average annual production for the 5-year period 1961-65 was 4,306 tons valued at $200,200. The material was marketed for use as a soil conditioner and a water softener. An article of mineralogical interest was published concerning the New Zealand glauconites.2

Jan 1, 1966

By Fredrick L. Johnson

In 1984, at the request of the U.S. Forest Service, the U.5, Bureau of Mines began a study of the 94,370-acre Arc Dome study area (4-667) in order to appraise its mineral resources, The Bureau of Mines mapped and sampled mines, prospects, and mineralized sites in and near the area, The study area is located in the Toiyabe National Forest, about 54 mi north of Tonopah, Nye County, NV, It is estimated that over 500 claims have been staked in the study area since the mid-1800?s. In January 1986, there were 108 active mining claims completely inside and 59 on the boundary. Another 283 active claims were outside the study area but within 1 mi of the boundary, In addition to the large number of claims staked, exploration activity is also reflected by the almost 700 inactive workings that were found during field investigation.

Jan 1, 1989

By H. W. Davis, W. W. Adams, O. E. Kiessling

"Current economic problems frequently have focused attention upon the lack of adequate quantitative information indicating the relationship between human effort and output in various branches of the mineral industry. With the exception of complete records covering coal mining, only scattered information on the units of human energy required to produce a unit of raw material is available for most of the important industrial minerals. Fortunately a virtually complete statistical record is available covering this phase of the iron-ore mining industry.For many years iron-ore mining companies, whose interest in safety work is well-known, have reported annual data on employment to be used in the compilation of accident statistics. These data on hours of labor and other detailed employment information have been correlated with the statistics on production also reported annually by producers. The outstanding trends shown by this composite record for the 10-year period 1923-32 are included in the following discussion, supplemented by a summary table that presents the principal statistical background of the study. 5The substantial reduction in the number of men needed to produce the annual iron-ore requirements of the United States, as shown strikingly in the graphs, illustrates that in iron-ore production improvements in technology have been consistently winning a battle over the difficulties of nature. In 1923, for example, 41,294 men working 107,551,244 hours were required to produce 69,351,442 gross tons of merchantable ore, equivalent to an average output of 0.645 ton per man-hour. In 1929, however, only 30,763 men working 77,111,686 hours 'zero required to produce 73,027,720 tons of merchantable ore, equivalent to an average output of 0.947 ton per man-hour. Thus, from 1923 to 1929 the average number of men working decreased 25.5 percent and the total man-hours worked 28.3 percent, while the average output per man-hour increased 46.8 percent and total merchantable ore production 5.3 percent."

Feb 1, 1935