Search Documents

By D. W. Mitchell

This Bureau of Mines report summarizes experience and past research on methods for sealing abandoned areas of a coal mine and areas from which the pillars have been wholly or partially extracted. The Federal Coal Mine Health and Safety Act of 1969 requires that such areas be ventilated or sealed with explosion-proof bulkheads, but the present study indicates that bulkheads alone cannot isolate areas in a coal mine in which methane and other dangerous gases have accumulated. Gas-air exchanges between sealed and open areas must be controlled.

Jan 1, 1971

By John W. Buch

Upon review of German World War II mining practices and equipment for planning coal, the Federal Bureau of Mines initiated research leading to the development of a pneumatic planer for anthracite. The results of tests are reported in this manuscript. It was demonstrated (1) that hard anthracite can be planed and (2) that the design and operating requirements are within the limits of present-day engineering and technology. For hard anthracite, the depth of cut indicated is 4 to 6 inches; with a chain pull of 20 to 40 tons and the speed of planer travel of 18 to 20 feet per minute, a 40-hp. motor will be required for the planer hoist. Compressed-air requirements for the planer will be 250 to 300 c, f, m, at 60 to 70 p. s, i. It was learned that the length of the 4 individual sections of the planer should not exceed that of the individual troughs of the armored chain conveyor (5 feet in this instance); otherwise, bottom coal will be left in synclines, and the planer will override the conveyor at anticlines. Pneumatic pushers should be operated from a separate compressed-air line fitted with a pressure regulator. Results indicate that additional development work is warranted.

Jan 1, 1957

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By A. L. Engel

Production of chromite in California has been from many small, high-grade mines. The opening of the Purchase Depot at Grants Pass, Oreg., in 1951 has stimulated chromite mining in California, and a large number of properties are being reexamined as there is a possibility that some low-grade ores from many of these properties can be beneficiated to meet the purchasing schedule. The Bureau of Mines in its program of conservation is continuing ore-dressing tests on chromite ores to better evaluate their potential. This report is a compilation of preliminary concentration tests on samples from five different properties in California. The concentration tests were made on ores from the David mine, Butte County, the Seiad Creek mine, Siskiyou County, the High Plateau mine, Del Norte County, Bud's mine, Tuolumne County, and tailings from the Miller concentration plant in San Luis Obispo County, Calif., to determine the possibility of beneficiating these ores so that they will meet the specifications for the Government stockpile.

Jan 1, 1956

By Harry Freund

Gallic acid is a sensitive, stable, colorimetric reagent for the determination of tantalum in the range of 2 to 40 µg.Ta/ml. The method consists of the fusion of tantalum oxide with potassium pyrosulfate and solution of the cooled melt in satu-rated ammonium oxalate, followed by development of a yellow complex with an ethanolic solution of gallic acid. The tantalum-gallic acid complex absorbs over a broad region in the blue and near ultraviolet. Adverse effects due to interfering ions and solution conditions, such as oxalate concentration and pH, can be minimized by a suitable choice of wave length. A new and sensitive colorimetric method is provided that has been used successfully at the Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines for determining minor amounts of tantalum.

Jan 1, 1956

By R. W. Huber, R. C. Wiley, V. C. Petersen

"Three arc- melted ingots, two of a t itanium-7 percent manganese all oy and the third of unalloyed titanium, were forged and rolled into 3/ 4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties.These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots.INTRODUCTIONArc -melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Perk, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.Considerable data have been published recently on constitution diagrams and properties of titanium-manganese alloys in genera1. 3/ 4/5/6/ However, little if any correlation between processing schedules and end results has been published, particularly with respect to the present commercial production of the proprietary titanium manganese alloys . Several factors in the production of titanium and titanium alloys have a pronounced influence on the physical and mechanical properties of the finished product: (1) The degree and nature of impurities in the base materials, ( 2) the amount of impurities introduced during the melting cycle and their distribution, (3) the homogeneity of the alloy, (4) forging, (5) rolling, and ( 6) final heat-treating cycles. All of these item£ are important from a metallurgical standpoint in producing the desired end properties in the metal."

Mar 1, 1955

By S. M. Shelton, A. L. Engel

The carnotite deposits of western Colorado and adjacent sections of Utah and Arizona were formerly an important source of radium and uranium until displaced by the exploitation of foreign deposits in the Congo and northern Canada . Recently interest has been renewed in domestic carnotite ores as a source of vanadium . Carnotite is a canary - yellow, crystalline , pulverulent mineral occurring in sandstones in the Colorado - Utah district as an incrustation on the faces of joints and fractures and deposited around and between individual sand grains , often strongly adhering to the surface of the grains . Chemically, it is a variable combination of potassium, uranium , and vanadium oxides with water of crystallization . It is soft and friable , and occurs in fine - grained or earthy form . In spite of a specific gravity of 4.1 , gravity concentration has not proved practical as a means of beneficiation because of the earthy texture of the mineral . Vanadiferous sandstones occur with minerals ranging from roscoelite (vanadium mica) , containing little uranium , to high- uranium and low -vanadium carnotite . There is considerable local variation in the texture of the ores . The treatment of carnotite ores has been described previously , with attention directed to the elimination of waste in mining and the extraction of radium . The suggested methods included those suitable for the recovery of vanadium , since both radium and vanadium occur in the same minerals . Moore and Kithil suggested crushing from 40- to 80 - mesh with rolls , accompanied by a rubbing action to loosen the carnotite adhering to the sand grains . Fine grinding was to be avoided because it diluted the final product too much . The crushed and rubbed material was to be washed and

May 1, 1942

By Arthur Metcalfe, Edward Thomas, A. J. Barry

"Early in 1947 the Bureau of Mines became interested in adapting suspension roof support to coal mining 5/ as a possible means of reducing the high rate of accidents from falls of roof. For a time the program made little progress be¬cause of the shortage of steel products after the end of World War II, but during the past 8 months this restriction has eased, and as of May 1, 1949, 114 mines had either started experimental work or had ordered materials and equip¬ment in anticipation of trial installations. It is estimated that 30 linear miles of roof in underground passageways have been secured by this method in recent months, and no lost-time roof-fall accident has been reported in these areas up to that date.Many coal-mining companies in widely separated localities have cooperated in making experimental installations. In very few instances are these companies entirely satisfied that they have arrived at the best solution in determining the most efficient adaptation to suit their particular conditions. Moreover, new ideas and modifications of the basic principle are constantly being brought to light and are being tested. Available test data is far from complete, and it is conceivable that some new idea will be developed to alter the present concept of proper technique; therefore, this progress report does not attempt to answer all questions that might arise in connection with this method of roof support; it simply recounts the experience acquired to date. Consequently, few references to costs are made. Up-to-date quotations on material and equipment used in suspension roof-support installations may be obtained from numerous mine-supply companies.The authors gratefully acknowledge the cooperation of mining companies whose personnel made possible collection of the information contained in this circular: Bethlehem Collieries Corp., Barrackville, W. Va.; Berwind-White Coal Mining Co., Windber, Pa.; Consolidation Coal Co., (Ky.); Jenkins, Ky.; Consolidation Coal Co. (W. Va.), Fairmont, W.Va.; Clinchfield Coal Corp., Dante, Va.; Consolidated Coal Co., St. Louis, Mo.; Hanna Coal Co., St. Clairsville, Ohio; Missouri Portland Cement Co., Sugar Creek, Mo.; Pocahontas Fuel Corp., Pocahontas, Va.; Reppert Coal Co., Dola, W. Va.; St. Joseph Lead Co., Bonne Terre, Mo.; and Tennessee Coal, Iron, & Railroad Co., Birmingham, Ala.The fundamental theory of suspension roof supports is not new; in fact, its application in the construction of beams predates mining itself. The basic principle involved is the reinforcement of roof rock with steel rods inserted in the roof and anchored therein at points where the rock is least likely to be affected by stresses resulting from mining. Such roof supports have been used in mines for many years in widely separated localities. The St. Joseph Lead Co., operating in southeastern Missouri, apparently was the first large mining company to prove the practicability of the principle by applying it in a systematic manner for securing roof for more than 20 years (fig. 1)."

Sep 1, 1949

By Ronald T. Mayerle

In 1989, the U.S. Bureau of Mines conducted a mineral investigation of the Mallard study area near Elk City, Idaho. The study area comprises most of the original Mallard RARE II area (1-847) plus some additional lands. The investigation is part of an ongoing, multi-year study of north-central Idaho that is being conducted in cooperation with the Idaho Geological Survey and the U.S. Geological Survey (USGS). The only identified resources are rock suitable for road metal. Five lode prospects and a pyrite-bearing rock quarry, which is operated by the Forest Service for aggregate, were examined for metals. One of the prospects warrants additional exploration for silver in quartz veins, but the chance of finding an economically minable deposit is limited. Several rock and stream sediment samples were anomalous in various metals. Two of the more promising localities for gold and/or other metals are adjacent to a unit of the Frank Church-River of No Return Wilderness that the USGS classified as having a moderate potential for gold deposits related to fossil hot springs.

Jan 1, 1991

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By J. A. Herdlick

At the request of the War Production Board a preliminary examination of the Big Ben molybdenum prospect near Neihart, Cascade County, Mont., was made by the Bureau of Mines under G. N. Bennett, mining engineer, Bureau of Mines Montana district office, in September 1942. Formal investigation, consisting of sampling, core drilling, and metallurgical testing, was later undertaken and completed in 1943. Field work was directed by Robert D. O'Brien, mining engineer, Montana district office, under the supervision of E. W. Newman, supervising engineer, Montana district office. This report describes the deposit, presents the factual data obtained from the sampling and core-drilling operations, and summarizes the results of the metallurgical studies. The deposit was first located and prospected in 1922 by the present owner, Frank Mansikka of Neihart, Mont. Periodic examinations made by responsible mining interests were culminated in 1938 when the Federal Mining & Smelting Co. optioned and investigated the property. No ores have been produced from the deposit to date.

Jan 1, 1949

By G. E. McElroy

Economic solutions of problems of mine-ventilation improvement can be found by mathematical analyses of alternative methods of procedure, but, in the case of our older bituminous-coal mines, the airway network is usually so complex that mathematical solutions are too tedious to be practical. Recourse usually is made to extremely costly and uncertain trial-and-error procedures with the existing layout and equipment. The resulting errors often prove costly and sometimes create hazardous conditions. Both the economic and safely aspects of alternative methods of ventilation improvement may be rapidly and cheaply investigation with analogue computers. An electrical analogue computer, designed and built especially for analyzing mine-ventilation-distribution problems, has been placed in service by the Bureau of Mines at its Pittsburgh, Pa., Experiment Station. It is a nonlinear, low-voltage, fluid network analyzer of a type developed by Malcolm S. Mcllroy, professor of electrical engineering at Cornell University. It was designed in close coopera¬tion with Professor Mcllroy and built by the Standard Electric Time Co., Springfield, Mass. It is the seventh unit of this type to be placed in service and the first designed for mine airflow problems. The other six were designed for either water- or gas-distribution analyses. Three are much larger and more expensive units. The largest unit has a capacity of 20 sources, 576 mains, and 180 loads, or regulated-flow paths. The Bureau unit has a capacity of 5 sources, 128 mains, and 48 loads.

Jan 1, 1954

By P. E. Churchward

The Bureau of Mines developed a process using amines for recovering tungsten as ammonium paratungstate from alkaline leach liquors without producing synthetic scheelite as an intermediate product. Over 90 pct of the tungsten in low-grade scheelite or ferberite concen-trate was recovered as ammonium paratungstate by (l) autoclave leaching the concentrate with Na2CO3, (2) solvent extraction of the acidified leach liquor with kerosine solutions of either a quaternary amine (Aliquat 336) or a primary amine (Primene JM-T), (3) stripping the tungsten values from the quaternary amine with ammoniacal NH4C1 or from the primary amine with NH4OH, and (4) crystallization of ammonium paratungstate from the strip liquor. Reagent consumption in pounds per pound of W03 recovered was, for the quater¬nary amine, 3 Na2CO3, 3.5 H2SO4 , 2.2 NH4Cl, 1 NH3, and 0.4 glacial acetic acid; for the primary amine, it was 3 Na2CO3, 3.5 H2SO4, .06 NH4Cl, and 0.9 NH3. Both reagents extract molybdenum along with tungsten. Silicate and phosphate are partly extracted and contaminate the product; leach liquors containing these impurities require preliminary purification.

Jan 1, 1966

By W. N. Marchant

The Bureau of Mines performed chemical research to elaborate details of sulfur chemistry pertaining to the citrate flue gas desulfurization process in which sulfur dioxide (SO2), absorbed (as bisulfite ion) in a buffered sodium citrate solution, is reduced by hydrogen sulfide (H2S) according to the overall reaction 2H2S + HSO3 + H+ ? 3S + 3H20. The rate-limiting step in the process was shown to be the reduction by H2S of thiosulfate (S2031-) that is formed as an intermediate. Pseudo first-order kinetic measurements were made at room temperature to retard the reaction sufficiently that adequate analysis was possible. These measurements showed the rates of the following net processes to be -d [S02]/dt (pH 4.5) = (0.409±0.050)min-1 [S02]; d [S2032-]/dt (pH 4.5) = (0.199±0.017)min-1 [S02]; -d [S2032-]/dt (pH 4.0) = (0.0437±0.0265)min-1 [S2032-]~1; -dH2S/dt (pH 3.9) = (21.6±3.0) mmoles/min-atm [H2S]g1.4, where [H2S]g is the partial pressure of H2S in the gas phase, in atmospheres, and the rate describes the consumption of H2S, in millimoles per minute; d[S]/dt (pH 4.0) = (38.0±3.4)min-1 [H2S]1, where [H2S] is the concentration of H2S in solution. Hydrogen ion consumption during the slow phase of regeneration was shown to occur at (2.1±0.5) times he rate of thiosulfate consumption, which is interpreted as evidence for the following as the rate-limiting reaction: 2H2S + S2032- + 2H+ ? 4S + 3H20 A scheme consisting of five sequential general reactions is proposed to account for sulfur formation.

Jan 1, 1981

By W. F. Marshall

This Bureau of Mines report discusses tests conducted with four different catalytic reactor designs to determine the influences of exhaust treatment systems on emissions from diesel engines. Although there was significant differences in oxidation efficiencies at light to intermediate engine loads, all four catalysts were very effective in reducing emissions at heavy loads. Compositional determinations included carbon monoxide, carbon dioxide, unburned hydrocarbons, oxides of nitrogen, aldehydes, sulfur dioxide, sulfates, and particulate loading. Particulate size, exhaust odor intensity, and the character of the unburned hydrocarbon component were also determined.

Jan 1, 1978

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By A. Wahab Khair, N. P. Reddy

"INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982).One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Morgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cytotoxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le Roux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly. Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield, 1984) while Dodgson, et. al., (1971) concluded that high exposures to minerals such as illite, kaolinite and mica will retard the progress of CWP. Size and shape characteristics are believed to be important in the relationship between mineral particles and health effects (Shedd, Virta and Wylie, 1982)."

Mar 1, 1989

By W. W. Adams

"A recent paper prepared by the writer summarized the results of an analysis of the accident records of 34 metal mines for the calendar year 1925. The present paper summarizes the results of a similar analysis of the accident records of 59 coal mines for the same year. This summary is based upon reports furnished to the Bureau of Mines, Department of Commerce, by operating companies that par¬ticipated in the National Safety Competition of 1925.The purpose of the Competition was to establish the lowest accident-severity rate, thus showing the smallest loss of time from accidents in proportion to total number of man-hours worked. The reports covered all lost-time accidents that occurred during the year, that is, all accidents that disabled an employee beyond the day or shift on which the accident occurred. Detailed information for each of the 59 coal mines is given in the appended table. Each mine employed at least fifty men underground; over half of than employed more than 200 men underground. Hence the accident records should be typical of those of large-scale mining operations in general where the company is devoting special attention to accident-prevention work. The mines covered by the reports are situated in eleven States: Alabama, Illinois, Indiana, Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Utah, Washington, and West Virginia.A tabulation of the reports covering the 59 mines showed an accident-frequency rate of 123 per million hours of ""exposure* and an accident-severity rate of 10.214 per thousand hours of exposure3. The total volume of exposure or employment was 29,117,561 hours, representing the equivalent of work of 12,000 men for three hundred 8-hour shifts. The records covered employment and accident above ground as well as underground, although they did not include stripping or open-pit mining. Accidents during the year resulted in 33 deaths, 1 permanent total disability, 28 permanent partial disabilities, and 3,510 temporary injuries. These accidents represented a loss of tine equal to 297,417 man days. In arriving at this lost-time equivalent, each fatality and permanent total disability was weighted at 6,000 lost days (see footnote 3), as specified in the scale adopted by the International Association of Industrial Accident Boards and Commissions; permanent partial disabilities were weighted according to nature of injury, in accordance with the scale adopted by the :Board; temporary injuries were weighted according to the actual number of calendar days during which the employee was incapacitated as a result of the injury."

Nov 1, 1926

By Alla D. Mah

Heat content and entropy data at high temperatures were obtained for cuprous oxide (Cu2O) and cupric oxide (CuO). Experimental results and smooth values are reported. Equations are given for heat content increments and heat capacities above 2980 K. Low-temperature heat capacity data were obtained for cuprous oxide. Evaluation of the 2980 K entropy gave, S°298.15(Cu2O) = 22.08 ± 0.10 cal/deg mole. Heat of formation values were determined for cuprous and cupric oxides. The values are: AH°298.15(Cu2O) = -40,830 ± 300 cal/mole, and AH°298.15(CuO) = -37,230 ± 150 cal/mole.

Jan 1, 1967