Search Documents

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By P. L. Swanson, A. T. Iannacchione, W. J. Gale

This paper outlines the concepts used to correlate rock failure with microseismic events and presents examples of microseismic monitoring together with associated computer modelling of the rock failure. This study is motivated by the need to develop improved ways to reduce ground control hazards in underground mining. Toward this end we present and compare results from numerical modelling and micro- seismic monitoring studies conducted at several different mine sites. Emphasis is on integrating results obtained with these tools to characterize, and thus increase our understanding of, important mine deformation processes. The ultimate goal is to use this knowledge to design mine structures, and develop mitigation measures, that minimize specific ground control hazards.

By B. D. Sartwell

The formation of alloyed regions near the surface of metals using ion implantation is being investigated by the Bureau of Mines as a means of providing corrosion resistance using much smaller amounts of the strategic alloying metals. Two ion implantation systems that can implant low-energy chromium, nickel, or aluminum ions into low-cost substrate materials such as iron or carbon steel have been designed and constructed. The development of the ion source, ion beam acceleration stage, mass analysis system, and target chamber are described in detail. The ion-implanted alloys have been characterized using proton-induced x-ray emission to give the total number of atoms implanted and to determine the extent of any surface contamination introduced by the ion implantation process. Research conducted at other laboratories on metallurgical applications of ion implantation is given.

Jan 1, 1980

By Henry H. Ginsberg

The effectiveness of 0.01 pct. molybdenum, as ammonium molybdate impregnated on coal, on the hydrogenation of a high-volatile bituminous C coal at 8,000 p.s.i.g. and 460° to 480° C. has been studied in a pilot plant by the Federal Bureau of Mines. Under these conditions, the Bureau obtained 98 to 99 pct. conversion5/ of coal to liquids and gases at throughputs of 29 to 101 lb. of m.a.f. coal per cubic foot of reaction space per hour. At 460° C. the indicated yield of oil ranged from 63 pct. (based on m.a.f. coal) at a throughput of 35 lb./c.f.h. (pounds per cubic foot per hour) to 68.5 pct. at a throughput of 58 lb./c.f.h., and the yield of gaseous hydro-carbons ranged from 25.5 to 19 pct. at the same throughputs. The maximum measured yield of oil boiling under 325° C. was 47 pct.

Jan 1, 1960

By R. A. Beall, S. L. Ausmus

The development of a completely water - free expendable graphite mold material , useful for reactive metal castings , has been detailed . Mixing and curing variables have been evaluated both by physical testing of the material itself and by castings of titanium , zirconium , and hafnium . The blend of powdered graphite , cornstarch , dextrin , cereal binder , linseed oil , and Carbowax -4000 is a successful mix when mulled in a carbon dioxide atmosphere , and properly cured and fired . The primary advantage of this material is its adaptability to standard foundry techniques ; i . e . , core blowing and hand ramming . Temperatures in the curing and firing cycles do not exceed 960 ° C , and no vacuum firing is required .

Jan 1, 1964

By A. G. Starliper, H. Kenworthy

A procedure was developed for the separation of lead and sulfur in industrial concentrates of galena by a combination of chlorination and fused - salt electrolysis . Galena could not be satisfactorily electrolyzed in the various media tried ; however , when it was treated with chlorine the resulting lead chloride could be effectively separated electrically into lead and chlorine . An apparatus was designed and constructed to chlorinate galena and to volatilize simultaneously most of the chloridized impurities . By electrolyzing the chlorinated concentrate , a high percentage of lead was recovered . Anodic chlorine was drawn from the cell and was used to chlorinate new feed . In many runs , the recovered metal analyzed from 99.8 to 99.9 percent lead . Lead was also distributed as a chloride in the bath , and a small portion was in the volatile fraction produced during the chlorination step . During a tinuous operation , only 0.1 percent of the total lead was discarded ; 99.9 percent was accounted for in the metal , electrolytic bath , and washed or leached chlorination condensate which was essentially lead chloride . About 95 percent of the sulfur from the galena was recovered as a byproduct of over 90 - percent grade .

Jan 1, 1964

By S. S. M. Chan

The Bureau of Mines has investigated the structural aspects of shafts and support systems using the finite-element technique. In situ field measurements in deep, vein-type metal mines show that rock stresses are often higher in the horizontal direction than the vertical, and unequal in the horizontal plane. These data and laboratory and field-determined physical properties were used as input to analytical studies. Various design and construction parameters were investigated to deter-mine the effect on shaft stability. Rectangular shafts were studied in detail to determine the effects of applied stress ratio, shaft orientation and dimension, influence of interbedded quartzite and argillite, and rock fracturing. Various support systems were analyzed, including concrete lining, timber, and steel sets. Circular configurations were investigated to evaluate yield zones and liner thickness. Elliptical shafts and time effects were briefly evaluated to illustrate shape and time effects and demonstrate the methodology. It is shown that the magnitude, direction, and ratio of applied stress and rock mass anisotropy are keys to determining shaft stability. A realistic conceptual framework was developed with which to examine the rock and support interaction in deep mine shafts. Structural analysis techniques overcome some of the historical difficulties with shaft de-sign by defining the field data requirements and structural sensitivity of various design and construction parameters.

Jan 1, 1985

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data oil motor gasolines sold during the minter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular- price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By Gustav Wafe

"INTRODUCTION The discovery in 1901 of ""gusher"" oil production at Spindletop, Tex., Tex., a salt-dome structure, led to exploratory drilling on other known domes and known domes and in areas contiguous to salt domes in the Gulf Coast region of Texas and Louisiana. Early drilling on the flanks of the domal structures disclosed incompetent 3/ shales, which flowed into the hole when attempts were made to drill through them. Often these shales seized the drill pipes and presented with equipment then in use, an insuperable barrier to deeper drilling. The obstructing incompetent shales came to be called ""heaving"" shales by drillers who attempted to drill through them. Formations of this type have hampered the penetration of the drill bit in many area in the Gulf Coast region to such an extent that the drilling of wells through heaving shale has become a major problem."

Mar 1, 1942

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular-price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By Alla D. Mah

Titanium forms several compounds with oxygen and also is able to dissolve interstitially about 33 atomic percent of oxygen. Starting with titanium dioxide, reduction becomes increasingly difficult as oxygen is removed; and the final step, be reduction of the titanium-oxygen interstitial solutions, is by far the most difficult. The possibility of reducing titanium oxide, or of purifying titanium containing oxygen, by treatment with certain more volatile metals has been a subject of considerable interest. Theoretical appraisal of the limitations of this possibility, however, has been hampered by lack of adequate information on the thermodynamic properties of the titanium-oxygen solutions. The purpose of the present work was to remedy this difficulty by expanding the thermodynamic knowledge regarding these solutions. The experimental work involved three types of calorimetry and furnished the following information: (1) Heats of formation of 11 titanium-oxygen solutions, in the range of 0 to 10 wt.-percent oxygen, were determined at 298.15° K. As a byproduct, an improved value of the heat of formation of rutile was obtained, which, in turn, led to improved values of the heats of formation of the lower titanium-oxygen compounds. (2) Low-temperature heat-capacity data and entropies at 298.15°K in were determined for 2 representative titanium-oxygen interstitial solutions. (3) High-temperature heat-content data were obtained for 2 titanium-oxygen interstitial solutions to about 1,600° K.

Jan 1, 1957

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By A. W. Ambrose

"Introduction.Oil-field operations have often been carried on under great stress and haste, in which the prime purpose has been to put the wells down rapidly as possible, without regard to a few of the various factors affecting cost. In such fields as Burkurnett, Texas, where the well locations are town lots and other small tracts, the operator was concerned primarily with in drilling. In such cases a few thousand dollars more or less in the cost of a well not considered. We are reaching a time, however, when our reserves a,more definitely outlined and properties are being along more economic lines. Operators are becoming more concerned with the actual cost of this work, and are gradually learning that fuel consumption can be reduced in drilling and producing without delaying the speed of drilling, and in the case of production, it will greatly reduce the unit cost per barrel of production.Types of Field Boilers.In the oil fields there are in general two types of boilers; those which are used for drilling wells and are of a more or less portable character, and those established later in a more permanent form and serve for the purpose,of generating steam for producing the oil. As a rule, the latter type of boilers are larger than those of the drilling type. Usually, little care is given to the installation of drilling boilers; particularly in attempting to set them up in such a way as to avoid waste in of fuel. Because of the temporary nature of these installations there may be some justification for not giving them more,attention in this resend, but it is believed that a few precautions could be taken that would amply repay the cost and trouble taken. In connection with the boiler plants that are afterwards established, when a few producing wells have been,brought in with a life of two to ten years and probably longer, much care to the boiler-plant construction and to the installation of recording instruments which will assist in operating the plant at minimum cost."

Nov 1, 1920

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By H. S. Kalman

A table of factors for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, at base conditions of 14.7 psia and 70° F, is presented. The table covers a pressure range from 10 to 10,000 psin in 10-psi increments and a temperature range of 0° to 120° F in 2° increments. The volume of helium is calculated from the observed pressure and temperature of the helium, expressed as a factor from the table, and the known internal volume of the container. The calculation requires a single multiplication. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1968

By David Schlain

The galvanic corrosion properties of titanium in contact with commercially pure aluminum, copper, or type 302 stainless steel in some of the common organic acids were investigated. Acids used in these experiments were 10 percent formic, acetic, lactic, citric; 1 percent oxalic and tartaric; and 9 percent oxalic. Electrode-potential measurements and several types of galvanic couple experiments were carried out. Solutions were aerated by three methods: Flow of air, flow of helium, and natural aeration. Work was done at 35° C. with couples consisting of equal areas of the 2 metals. Titanium was resistant to corrosion in most of the organic acids studied, whether alone or in contact with a dissimilar metal. However, titanium coupled with aluminum did corrode in 1- and 9-percent oxalic acid solutions. Contact with titanium usually caused aluminum to corrode by galvanic action. Copper was subject to galvanic attack in 10-percent acetic acid with a flow of air. Contact with aluminum to some solutions in which titanium is ordinarily inert and noble with respect to aluminum caused titanium to corrode

Jan 1, 1956

By Lloyd H. Banning

With the ever-increasing demand for energy in all forms, electrical energy generated from geothermal resources could become an important energy source in the next few decades. Geothermal fluids, which contain appreciable quantities of dissolved salts and gases, are generally corrosive to materials of construction. Since data on corrosion of materials in geothermal brines is limited, the literature was surveyed through February 1972 to obtain a compilation of information on corrosion resistance of aluminum and its alloys, copper and copper-base alloys, carbon steel and cast iron, stainless steels, chromium-iron alloys, nickel-and cobalt-base alloys, and titanium in heated brines including sea water.

Jan 1, 1973

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983