Search Documents

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By Richard D. Smith

The Bureau of Mines evaluated the emission control methods, including the capital investments and operating cost, necessary for further reducing lead levels in ambient air at the Glover, Herculaneum, and Buick smelter-refineries in Missouri and the East Helena, MT, smelter. The U.S. Environmental Protection Agency (EPA) has proposed more stringent lead in ambient air standards than those currently in effect. This report presents theoretically achievable lead emission reductions and estimated capital and operating costs. Lead emission inventories theoretically can be reduced from 1985 levels by 2,421 lb/d at the three Missouri operations by containing and filtering fugitive emissions within structural enclosures and baghouses. The aggregated capital and operating costs in 1986 dollars using conventional environmental and workplace technologies are estimated to be $250,014,100 and $18,507,800, respectively. Estimated total incremental cost is $0.063/lb as refined lead. Additional regulatory costs attributable to Occupational Safety and Health Administration (OSKA), U.S. Department of Labor, workplace standards are included since proposed environmental controls may otherwise degrade workplace conditions. Continuous drossing is evaluated as an alternative to conventional OSHA controls. Substituting continuous drossing for conventional work- place technology results in an estimated aggregated capital and operating costs of $258,344,800 and $15,719,600, respectively. Estimated total incremental cost is $0.062/1b as refined lead. For comparison, the average open market price of refined lead during the first quarter of 1986 was $0.184/lb.

Jan 1, 1987

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By D. R. Tesarik

To ensure the stability ofa tailings pond embankment, the height of the phreatic surface must be kept at or below a safe level. In this investigation, the Bureau of Mines analyzed various horizontal drain designs for tailings embankments to determine their effects on location of the phreatic surface. This report describes the investigation, and it includes 21 dimensionless graphs that can be used to estimate the drain spacing and length dimensions necessary to ensure the stability of embankments of various configurations. Analyses were based on the use of two computer codes, a three-dimensional finite-element code and a two-dimensional finite-difference code. The computer-generated results were compared with results obtained from a laboratory embankment model, other laboratory test results, and piezomet-ric data from two actual tailings embankments. Nearly the same phreatic surface locations were predicted using either of the computer codes. For one of the actual embankments studied, the predicted phreatic surface location was slightly higher than the measured location; for the other, the predicted location closely followed the actual surface trend. Phreatic surfaces of the laboratory model were slightly higher than the code-gener-ated locations, and the differences grew larger as drain length increased or drain spacing decreased.

Jan 1, 1984

In 2001, 14,623 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). This was an increase of 210 mining operations compared to 2000. Almost half (49%) were sand and gravel mines, followed by stone (29%), coal (15%), nonmetal mines (5%), and metal mines (2%).

May 1, 2003

Objective: To identify and evaluate a permanent stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

By Bill Linville

During fiscal year 1969, the Bureau of Mines was engaged in 66 projects to improve methods for producing and utilizing petroleum. Programs directed toward the continued conservation of this natural resource, including crude oil, natural gas, and oil shale, were carried out through research performed at four laboratories supervised and supported by administrative personnel of this Bureau of the Department of the Interior. Over 100 technical papers and reports were published by the Bureau or others based on this research, and numerous other reports were prepared for U.S. Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau.

Jan 1, 1971

By Avery H. Reed

RECORD production of crude petroleum, lime, crushed marble, and talc highlighted the mineral industry of Alabama in 1963. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 86 percent of the total value of production, compared with 82 percent in 1962. The iron-ore industry continued to decline; in 1959 the value of iron ore produced was 12 percent of the total State production value; in 1960, 11 percent; in 1961, 10 percent; in 1962t 8 percent; and in 1963, 5 percent.

Jan 1, 1964

Research workers From the Bureau of Mines and industry met with other government and industry representatives in Pittsburgh, Pa., on January 22, 1975, to discuss the results of research under the Bureau of Mines Noise Control Program. The program, aimed at reducing noise in mines, is functionally divided into three major areas: Instrumentation, personal protection, and noise abatement. This proceedings contains the opening remarks to the seminar and seven technical presentations based on various aspects of noise abatement and control.

Jan 1, 1975

By Edward J. Chuhta, Joseph E. Chilton, Robert J. Timko

in underground mines to measure worker exposure to various gases such as methane, carbon monoxide, and nitrogen dioxide (NO2). Even in relatively small concentrations, NO2 can produce harmful side effects in underground workers. Mines using equipment powered by diesel engines, carrying out explosive blasting operations, and performing extensive arc welding and/or cutting work will have measurable quantities of NO2 released by these processes. Workers in these areas often use gas monitors to warn of excessive gas concentrations and to help them determine when to increase ventilation air that will dilute these gases, thus minimizing exposures to this gas. Portable gas monitors, used to measure NO2 levels, must be calibrated before each use. Calibration is typically performed using a small portable pressurized cylinder containing a certified gas mixture. The certified NO2 standard mixture, usually 10 ppm NO2 concentration, is diluted with either air or nitrogen gas. To determine the stability of commercially available portable gas standards, two different cylinders containing NO2 in nominal 10-ppm concentrations were examined. One cylinder was diluted in air, the other, in nitrogen. Baseline NO2 mixtures were generated using a standard liquid NO2 permeation tube operated at a constant temperature. Final dilutions of the test gas mixtures were made with air or with nitrogen using a mass flow-controlled gas dilution system. This study showed that, when a permeation-type NO2 generator is used, the electrochemical sensors in portable NO2 monitors provide identical results for gas mixtures whether they are diluted with air or with nitrogen. Two different gas monitors, one with a two-electrode sensor and one with a three-electrode sensor, were used to measure gas concentrations in the two commercially available cylinders. One month after the cylinders were delivered, the NO2-in-nitrogen cylinder, stated to contain 10 ppm NO2, measured 8.13 ppm. The NO2-in-air cylinder, also stated to hold 10 ppm NO2, measured 6.88 ppm. Therefore, before using NO2 gas cylinders to calibrate monitors, it is recommended that their concentrations be verified either by manufacturer recertification or by comparing the stated cylinder gas concentrations to a laboratory-based permeation tube-generated standard.

Dec 1, 2005

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No.4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 1, 1974

By Albert L. Toenges

The development of Alaska depends on the existence of an adequate fuel supply in the Territory. The need to investigate coal deposits was recognized as early as 1911, when the first investigations were conducted in Alaska by engineers of the Bureau of Mines. Conditions existing in the Bering River and Matanuska coal fields, as found by Dr. Robert A. Holmes, former Director of the Bureau of Mines, are described by the Honorable W. L. Fisher, former Secretary of the Interior./ Following Dr. Holmes' investigation, a party of Bureau of Mines engi¬neers headed by R. Y. Williams visited the Bering River field in 1912 in cooperation with the Navy Department. A detailed examination was made of the Bering River field, and 855 tons of coal were mined from three prospects on Trout Creek. This bulk sample was delivered to the Navy for steaming and other tests. A description of the work of the field party and results of tests of the coal by the Navy Department and the Bureau of Mines has been published.

Jan 1, 1949

By D. P. Schlick

As of June 30, 1970, Federal regulations required the operator of each underground coal mine to maintain the average concentration of respirable dust below legislative standards. As of March 1, 1971, over 152,000 respirable dust samples have been processed by the Bureau of Mines. Approximately 75 percent of underground working sections are being sampled in accordance with Federal regulations. Results indicate that 72 percent of the sections which have completed at least one basic sampling cycle are below 3.0 mg/m3, the standard in effect under the Federal Coal Mine Health and Safety Act of 1969 (P.L. 91-173). Notices of Violation were issued on 1,670 underground mines for failure to begin a sampling program; Withdrawal Orders were issued in 64 of these instances. Notices of Violation were issued on 1,121 sections where applicable dust levels were exceeded; Withdrawal Orders were issued in seven of these instances. There are 381 mining sections currently operating on permit; from the interim Compliance Panel.

Jan 1, 1971

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By K. Y. Haramy, R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 1992

By V. A. Danielson

The Bureau of Mines studied waste disposal methods a1 a coal mine in Kentucky and another in Alabama to develop cost estimates, to provide better knowledge of current practices, and to guide consideration of alternate disposal methods. Costs of the existing waste disposal systems at each mine were estimated using present-day costs of equipment and labor. Costs of waste disposal systems using alternate equipment were also estimated. Although total disposal costs were essentially the same for both operations, reclamation costs will differ because of different reclamation practices.

Jan 1, 1969

Capture airborne respirable dust generated by an auger-type continuous mining machine to reduce workers' dust exposure. Approach Install a water-powered scrubber system, operating at 1,400 psi, on the sides of the conveyor. The scrubber draws the dusty air from the face area and discharges cleaned air into the face return. How It Works Auger-type continuous miners pose unique ventilation and dust control problems. To protect face workers from the dust, the end of the brattice is usually maintained close to the face to increase ventilation effectiveness. However, it is taken down as the machine cuts toward the exhaust side to allow the machine to complete its cut. Often, the brattice is not reinstalled in a position to most effectively control

Jan 1, 1989

By F. W. Smith

To determine whether preheating coals before carbonization would improve the coking properties of the coals, particularly the weaker coking coals, 3 coals, 1 each from Illinois, Kentucky, and Pennsylvania, and a blend of the Illinois with a Pocahontas coal were preheated before testing for coking properties in the Bureau's BM-AGA pilot oven. The effects of preheating on the chemical and physical proper-ties of the coals and on the yields of carbonization products and strength of the coke produced from the preheated coals were determined, as were also the effects of bulk density, gaseous atmosphere, and residence time during preheating. Most benefit from preheating was found with weaker or oxidized coking coals, whereas the more strongly coking coals and blends showed little effect. Direct charging of preheated coal to the coke oven without cooling gave better coke, increased yield of tar, and decreased yield of gas. INTRODUCTION Although 94 percent of today's coal production comes from fields east of the Mississippi, the Eastern States have only about one-third of the Nation's recoverable reserves. West Virginia, which now produces more than any other State, has much smaller reserves than Utah, Colorado, and Wyoming.5/ However, the manufacture of iron and steel in Western States, which has increased greatly since World War I, is handicapped by the scarcity of high-grade coking coals, such as are plentiful in the Appalachian region. Unless a practical method of improving the cokemaking property of local coals is developed, ferrous metallurgical industries in the West must continue to use inferior coking coals and to pay high shipping charges for better coals.

Jan 1, 1958

By D. Harrington

This circular is part II of a series of papers reviewing the literature on air conditioning in mines with particular reference to the health, safety, and efficiency of employees. It deals with the physiological aspects of the principal physical qualities of mine air; part I (Information Circular 7001), chapters 1 to 3, discussed the physiological aspects of the chemical qualities of mine air, especially when contaminated with organic matter and noxious and toxic gases; part III will describe theoretical and practical methods of air-conditioning mines to try to correct or alleviate the conditions mentioned and will discuss the results attained by some of the systems now in use in various parts of tae world. With the present emphasis on the necessity for preserving the health of the Nation's defenders, industrial as well as military, attention should be called to the various conditions that may affect adversely their health and efficiency. One of the most important of these is exposure to abnormal air conditions, especially high temperatures and humidities. Therefore, it is believed that although the data presented here on the physiological effects of exposure to high temperatures cue intended mainly for the mining and allied industries, they are applicable to many other defense industries as well as to conditions present in some activities of the Army and Navy.

Jan 1, 1941