Search Documents

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By L. M. Sun

Baotou Baiyunerbo Mines Location in Inner Mongolia is a famous deposit of iron mineral and rare earth mineral accreting. The iron ore has very complicated ingredients and minerals composing. In the mine, there is not only magnetite ore but also hematite ore, so that it is impossible for high grade iron concentrate to adopt single wet low-intensity magnetic separation or high-intensity magnetic separation to concentrate iron mineral. Because of mixing the magnetite with hematite mineral in feed ore, recovery of iron of magnetite production system in the mineral processing plant is less than other mineral processing plants. Therefore, the research for increasing recovery of iron of the magnetite production system in the plant was undertaken. The paper presented the research for using dry magnetic separation to increase recovery of iron concentrate of the magnetite production system in the plant. It mainly includes dry magnetic separation test and wet magnetic separation and reverse flotation test. The test results indicated that dry magnetic separation is a important way to improve the feature of feed ore of the magnetite production system and to increase the recovery of iron. The recovery of iron may increase from about 70% to over 80%. The research also presented optimum operation parameters of the dry magnetic separator and the separation flowsheet. In conclusion, using dry magnetic separation to treat with feed ore of the magnetite production system in the plant to increase the recovery of iron is a feasible technique. The research present a new way for the mineral processing plant to made technology innovate to increase the recovery of iron concentrate of the plant in future.

Jan 1, 2014

By Chris A. Fleming

"The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative.There is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and nontoxic metals and ions in the tailings.This paper briefly discusses the pros and cons of the different processes that are available for the treatment of gold plant tailings to regenerate and recovery cyanide for recycling, and presents a techno-economic argument for the incorporation of this technology into many gold plant flowsheets today."

Jan 1, 2003

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By N. Dhawan

In the last decades, High Pressure Grinding Roll (HPGR) has gained significant importance in hard rock processing due to numerous metallurgical benefits such as energy savings, particle weakening, preferential damage of coarse particles, and preferential comminution-liberation. There are a limited numbers of lab-scale HPGR units throughout the world. The laboratory-scale HPGR machine at the University of Utah is first-ever lab-scale machine designed by late Dr Klaus Schönert, the inventor of HPGR. This HPGR is constructed with two counter-rotating hardened tool steel rolls, each 200 mm in diameter and 100 mm in width. The HPGR unit is equipped with eight sensors and a robust control system, which serves as an ideal system for fundamental studies and lab-scale testing. In HPGR operation, throughput, energy and product size distribution are intricately linked to specific grinding pressure, roll gap and rolls speed. The nip angle existing during the operation determines the volume of feed material above the rolls that is pulled into rolls without slip. In this paper, scale-up factors and some of the existing models have been reviewed. A number of experiments have been carried out with limestone and a slag material. The influence of operating variables and their complex relationship has been studied.

Sep 1, 2012

By V. A. Chanturiya

The results study the minerals oxidation were obtained by us during the methods of microscopic, FT-IR spectroscopic, XRD and chemical analyses of sulphides in tailings of copper-nickel wastes in Kola peninsula. Sulphide minerals begin to oxidize already at the stage of stockpiling and initial stages of storing. The proportion of non-ferrous metals and magnesium oxide increases with time, calcium partially precipitating in the form of gypsum. Comparison of heavy metal contents in pore solutions in cur-rent and stale copper-nickel ore concentration tailings has revealed a significant difference in practically all the parameters. The lower metal contents in current tailing pore solutions (by 5~30 times) are probably due to the presence of float reagent residues blocking oxidation. Much lower concentrations of magnesium and calcium can be accounted for by the difference in kinetics: the rate of sulphide oxidation at this stage is much higher than that of solution interaction with non-metallic minerals as the result of which the solid phase ? solution equilibrium is not achieved. It is generally believed worldwide that it the mining wastes with acidic pore solutions that pose the greatest hazard for the environment. Our findings suggest that although the solution pH in all the samples is higher than 7.8, the contain heavy metal concentrations by far exceeding permissible values. The direct determination of the total and silicate Ni contents in the tailings from current production and in storage tailings has shown that both sulphide and silicate Ni forms occur in tailings. However, the role of silicate Ni is much larger in the storage tailings. The average silicate Ni content accounts for 10% of the bulk Ni content in the current tailings and it increases to 40% in the storage tailings. Thus, the storage tailings are marked not only by sulphide oxidation and the removal of water-soluble sulfates, but also by the interaction of sulfates with the silicate matrix. Although complete equilibrium is not achieved even within 30 yr under polar-region conditions, the major part of the Ni in fine-grained fractions passes into silicate form. The probability of Ni transition to the silicate form directly correlates with the dispersion of the material and the amount of chemically reactive serpentine and hydrochlorite. The migration of Ni as sulfates and its precipitation by chemically active silicates distorts the distribution of this component in the coarse- and fine-grained fractions that are typical of tailings from the current production of copper-nickel ores. On the one hand, the variation of the mode of Ni occurrence in storage tailings lowers the value of technogenic raw materials as a source of this metal.

Jan 1, 2014

"The business importance of water for mining companies is unequivocal as it may affect several aspects of mining projects ranging from the life-and-death license to operate to the imperative economic viability. It is thus no wonder that nearly all mining companies acknowledge water-related risks, issues and opportunities in their respective sustainability report. Somehow, this procedure has fostered the idea that water frugality could be the sustainable solution to several water-related issues. The regular exercise of water accounting should then follow as a key strategic requirement. Water accounting is defined as the application of a consistent and structured approach to identifying, measuring, recording and reporting information about water. However, several factors discussed herein have led to the fact that some water accounts are still produced using means (hardware and software) which undermatch the value actually associated with water. The resulting fuzziness about water usage could result in missed opportunities, suboptimal operations or even lead to environmental law violations. This paper subscribes to the distinctive perspective that, once underlying concepts and practical definitions have been standardized under a supported framework, such as the openly available Water Accounting Framework (WAF) published by the Minerals Council of Australia, most of the remaining water accounting issues may be boiled down to accuracy issues and, ultimately, to how much accuracy is valued by the stakeholders. Using the latest WAF document as a baseline for best practices of water accounting and, borrowing concepts from the fields of sensor network design in the process industries and best practices of metal accounting, this paper reviews some essential accuracy issues to be considered when designing or analyzing water accounting systems in mineral processing. The current paper also includes some elements for a promising attempt to include the value of information paradigm inside the water accounting best practices."

Jan 1, 2014

With rapid development of Chinese iron & steel industry, it is of significance to intensify the utilization of domestic complex iron ore resources. The tin, zinc-bearing complex iron ores are typical polymetallic and intractable ones because of the complicated intergrowth relations among the multi-elements, and they have not been efficiently utilized, presently. Based on the thermodynamic analysis of iron, tin and zinc oxides reduction by CO, the technological conditions of tin and zinc recovery and pellets preparation from tin, zinc-containing iron concentrates by selective reduction roasting are studied and a new comprehensive utilization process is developed in this investigation. Under the optimum conditions, the tin and zinc volatilization is respectively in excess of 80% and 70%, and the compression strength of roasted pellet is more than 2500 N/P. Moreover, the residual tin and zinc in the finished pellets is below 0.06%. The finished pellets can be used as high quality iron-making burdens for large-scale blast furnace.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

This paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.

Jan 1, 2003

By O. Kökkilic

This study covers the tests to develop separation process for production of clay and colemanite rich concentrates, and aims to serve the clay and colemanite concentrates extracted from the tailing dams to the industrial applications. For this purpose, samples from the tailing dams in Kestelek Boron Plant (Turkey) with an average B2O3 content of 8%~11 % were subjected to the investigations. The separation process of hydrocyclone--to make clear the way to obtain either clean clay or cole-manite--was initially discussed. Therefore, following the gentle scrubbing (to keep the bimodal size distribution between clay and colemanite) of the tailings to disperse the slurry, two alternative multistage hydrocyclone processes; allowing to recycling the overflows or underflows to concentrate clay and colemanite were respectively tested. As a result of the preliminary tests, the multistage hydrocyclone separation in direction to the clean colemanite concentrates (recycling the underflows) gave the better separation efficiencies. So, all the parameters such as apex and vortex finder diameters and feeding pressures were examined with the multistage hydrocyclone process allowing the recycling the underflows. The detailed multistage hydrocyclone separation process of the tailing dam wastes yielded with colemanite concentrates (approx. 12 % of the feed, w/w) with B2O3 content of 35.0 % and the clay concentrates (approx. 42 % of the feed, w/w) with B2O3 content of 2.1 %. Colemanite concentrates were found good enough either to re-feed in to the separation process or to keep upgrading for final product ready to use in Industry whereas the attempts on production of light bricks from clay concentrates has failed. But it is worth to point out that these clay concentrates can be used for agricultural purposes just in the form as it is.

Jan 1, 2014

By Z. C. Zhen

Basing on character of fine ores, and employing all the advantage of dissolved-air flotation, the study within the dissertation put forth the methods of superfine metal mineral flotation with dissolved-air flotation equipment, and constructed a full set of laboratory flotation system. Experiments both in water and in slurry were respectively carried out by means of this flotation equipment. Further study was also fulfilled on mechanism of air-dissolved released devices, and the key components of system including ejector, releaser and saturator were designed. Optimizing devices parameters were chosen by taking ideal performance of the devices into consideration, according to orthogonal experiments and tests on bubbles factors, those performance factors were called air release rate, air release efficiency. The results with some minerals are better than JJF flotation machine with 30 litres bulk. The Dissolved-air Flotation(DAF) machine shows great potentiality in treating super-fine metal mineral concentration. The research indicates the Dissolved-air Flotation(DAF) system has superiority over mechanical flotation machine in fine flotation. Air-dissolved released bubbles appear on the surface of hydrophobic minerals in priority, solving collision probability less in the tradition fine mineral separation, such that the metallurgy technology of fine metallic minerals are improved. The exploratory research is a foundation for industrial pilot, commercial test and equipment maturity in the future.

Jan 1, 2014

By Y. G. Sun

This paper mainly reported separation manganese silver oxidized ores process by amylum de-gradation reduction and its influencing factors. When dosage is given according to nMn : nH2SO4 : n(C6H10O5)n : nH2O=1:k21.8: k116.66:30, the amount of up to 95.93% Mn leach rate and less than 2% silver loss can be obtained. Cyanidation process was used to extracted silver from leaching Mn residues. Silver leach rate could reach 94.15% at consumed amount of 1kg/t NaCN for 1h. Silver leach recovery rate was more than 92.27% by leaching Mn and cyanidation two-step processes so manganese and silver were separated effectively.

Jan 1, 2014

By J. H. Zhang

An atomic force microscope has been used to measure the forces acting between two silica and two rutile surfaces in the presence and absence of cationic surfactants, CnTACl (n = 12~18). The forces measured in the absence of surfactant can be fitted to the DLVO theory. At short separations, however, the silica surfaces exhibited repulsive hydration forces, while the rutile surfaces did not. On the other hand, the forces measured in the presence of the cationic surfactants show long-range attractions that are larger than the van der Waals forces. The long range attractions are the strongest at of the point of charge neutralization (p.c.n.), which decreases with increasing surfactant chain length. The possible origin of the long-range attraction has been tested in view of the charged-patch model of Miklavic et al. (1994). However, the sizes of the patches back-calculated from the model were much larger than those the patches (or hemi-micelles) determined experimentally and reported in the literature. It is, therefore, suggested that the long-range attractions observed in the present work are due to the structural response of the water molecules in the vicinity of hydrophobic surfaces.

Jan 1, 2014

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various ore complex ore and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides (pyrite, arsenopyrite, pyrrhotite, chalcopyrite and galena) and other phases (including hematite, magnetite and goethite) for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay and Gorain, 2014; Chattopadhyay et. al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2018

By Ashok Kumar, Subhadra Sen Dr. Rashmi Kumari, D. P. Chakraborty, Ajay kumar Gupta

The blast furnace coke quality depends on the characteristics of coal blend, pre-carbonization techniques adopted such as stamping, vibro-compaction etc., and coking conditions. Of the above, coal blend plays a significant role in the production of quality coke. Furthermore, the quality of the blend depends on the quality of individual coals and their interaction making up the blend. During transportation and stockpiling, coal is in contact with air for periods of time that sometimes may exceed several months. During this time, reaction with oxygen in the presence of water, sunlight and possibly elevated temperatures may take place. The resulting weathered coal suffers some alteration in its technological properties, which in turn affects coke quality for Blast Furnace operation adversely. In this work, two coals belong two prime hard coking and hard coking categories, namely Illawarra & Tahmoor, were selected and kept in a separate stock pile for a period of 120 days. These coals were characterized in terms of proximate, rheological & petrography properties at a regular frequency. This report summarizes the impact of weathering on the coking behaviour of these two coals in terms of properties as mentioned above. However, the rate of loss depends on coal rank and storage conditions. This has been seen through this study that the loss depends on coal rank and storage conditions. Deterioration of rheological and petrographic properties were seen higher for low-rank coals, like in this study Tahmoor, which is a low rank coal, compared to Illawarra showed higher degree of coking property degradation within the same time period under identical environmental conditions. Low-rank coal deteriorates at a faster rate because low-rank coal is dominated by free radicals that easily react with oxygen, resulting in the creation of various carbonyl groups and weathered vitrinite. Based on the results obtained in this study, size of stock piles for different qualities of coals to be maintained, at a specific time, can be determined and recommended, so that target coke quality is always achieved.

Jan 1, 2018

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014