Search Documents

By Tiruvengala Padma, Nilesh Naik

Piles are common type of deep foundation elements used for the special bridges, transmission towers, Jetties, and tall structures. Lateral loads on the structures can be due to either earth pressures, wind, waves, impact, moving vehicles and eccentric application of axial loads or in combination of the loads. Hence the lateral capacity of piles plays a major role in determining the pile dimensions. The laterally loaded pile analysis is a soil-structure interaction problem as the lateral capacity of pile depends on the soil strength and stiffness parameters and its reaction to the lateral load on pile. The common approach to determine the lateral load analysis of piles is the Beam on Lateral Springs Method also known as “p-y” method. In this method the pile is modelled as a beam and supporting soil is modelled as lateral springs. This study is focused on the comparison of output obtained from three geotechnical softwares namely FB-MultiPier, L- Pile and Wallap. L-Pile Software is based on Finite Difference Method, Wallap on Horizontal Subgrade Modulus Method and FB MultiPier on Finite Element Method. Pile response in terms of deflection, shear force and bending moments under vertical and horizontal loads from above three software are compared and concluded.

Sep 1, 2022

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016

By Eric Lindquist, John Compagnone, Gabriel Carvajal

"Condon-Johnson & Associates, Inc. (CJA) with the assistance of design consultant, Brierley Associates, designed and installed a water tight shoring system utilizing several ground improvement techniques jointly. Prior to the installation of the shoring system, a test program consisting of the installation and testing of 7 jet grout columns; 1 soil mix panel; 7 soil anchors and 3 tie downs was performed to verify design assumptions. State-of-the-art quality control measures were employed throughout the project.The shoring system consisted of:•,Deep Soil Mixing (DSM) wall utilizing triple axis tooling to install overlapping columns along the perimeter of the proposed excavation to a treatment depth of 54 feet.•,Installation of steel piles in DSM to provide rigidity to the wall.•,Installation of a jet grout bottom seal, installed from surface to a depth of 58 feet below existing grade.•,Installation of 153 soil anchors, 1-1/4” diameter and 47’-6” length, to tie the jet grout bottom seal to the native soil below to resist hydrostatic uplift, installed from existing grade to a depth of 91 feet.•,Installation of walers and pipe struts for internal bracing•,Installation and stressing of 117 tie downs, 1” diameter and 16 ft length, to tie the pump station mat slab to the jet grout bottom seal, installed from inside the excavated pit.Subsurface conditions at the site consist of uncontrolled fill materials to a depth of 20 feet comprised of sandy silt and clayey sand. The native soils underlying the fill generally consist of soft and compressible lean clay and silt with varying amounts of sands to a depth ranging from approximately 44 to 54 feet below ground surface, which in turn are underlain by dense to very dense silty sand. The groundwater elevation at the site is approximately 8 feet below ground surface.This paper covers the design aspects, construction, and quality control measures undertaken by the geotechnical contractor, with supporting figures.INTRODUCTIONThe owner, County Sanitation District No. 2 of Los Angeles County, designed upgrades to their existing Long Beach Main Pumping Plant Facility. The upgrades consist of a new pump station that includes a reinforced concrete below-grade wet well and dry well, a two-story operations building, two 78-inch diameter pipe inlets, two 42-inch diameter discharge pipelines connecting the existing manifold, two pipe junction structures, two insert-type junction structures, and electrical transformers. This paper focuses on the excavation shoring for the new pump station. The original shoring design concept for the pump station excavation illustrated on the contract plans consisted of pressed in sheet piles, a jet grouted bottom seal with soil anchors, 2 levels of internal bracing, and tie-down anchors to resist hydraulic uplift forces on the buried pump station."

Jan 1, 2017

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Filippo Maria Leoni, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed to reduce flood damages in the City of New Orleans and surrounding parishes, the SELA-22 project entailed the construction of a concrete covered canal along Jefferson Ave. and Prytania Street. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate under-seepage, thus creating a so called bottom plug, and provide structural support for the concrete box culvert. The U.S. Army Corps of Engineers (USACE), New Orleans District, selected the jet grouting technology for the construction of the bottom plug to a maximum depth of approximately 40 ft, and for a total length of approximately one mile. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid jet grout technology which, by limiting the overlap between adjacent columns, allowed a reduction of the overall number of installations. Approximately 2,400 elliptical jet grout columns were installed in a very challenging environment, especially under a logistical point of view. This paper will summarize the main features of the project, focusing on the innovative technological solution adopted to maximize productivity and on the several challenges faced in such limited and complicated logistical conditions.INTRODUCTIONThe Southeast Louisiana (SELA) drainage program has been designed with the purpose of reducing flood damages in the City of New Orleans and surrounding parishes. This will be accomplished by constructing new pumping stations and better drainage canals throughout. The program was authorized in 1996 by the United States Congress and administered under a project cooperation agreement between the Sewerage and Water Board of New Orleans (SWBNO) and the USACE.Prompted by the severity of damages associated with rainfall flooding in southeast Louisiana, the SELA program consists of several individual project components. The proposed work is located on both the east and west banks of the Mississippi River in the Orleans and Jefferson Parishes, as well as in portion of St. Tammany Parish."

Jan 1, 2017

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By Anne Lemnitzer

When a major storm system stalled over Western Europe last summer, it pro- duced the deadliest flood on European territory in the last two decades. Beyond record-setting rainfall over countries such as Luxembourg, Switzerland, France and the Netherlands from the storm's "Bernd" low pressure system, more than 230 people were killed in Germany and Belgium. The storm system also caused over an estimated $20 billion (€17.7 billion) of damage. A team from the Geotechnical Extreme Events Reconnaissance (GEER) Association, supported by the National Science Foundation, was mobilized to investigate the potential impacts of the widespread flooding in Germany, Belgium and the Netherlands. Members of the DFI Europe regional chapter closely collaborated with the U.S.-based GEER team and many other engineers and scientists in Europe to collect perishable data and study flooding effects and the event's resulting impacts on geostructures, such as bridges, retaining walls, dikes and embankments. This article features some of the vast information collected by the team, which has recently been published in a comprehensive reconnaissance report and made available for free at geerassociation.org. All data will also be accessible at the NEHRI DesignSafe Cl data repository.

Feb 1, 2022

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By Mohini Patel, Jahnavi Parmar, Pranav R. T Peddinti

Expansive clays pose a variety of geotechnical problems. Although the admixture stabilization is proven to address their problematic swelling and shrinkage characteristics, the influence of unsaturated condition on the engineering performance of these soils needs further research attention. In addition, highly saline soils with high organic content would further alter their performance. A similar soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, India. High salinity in the in-situ expansive soil of basaltic origin and the prevailing unsaturated condition, enforces the engineers to look out for possible soil treatment methods. In this regard, the present work attempts to analyze the unsaturated behaviour of this soil when fly ash is used as an admixture. A comparative study for stabilized and unstabilized mixes is performed in terms of their unconfined compressive strength, electrical conductivity, swell characteristics and California Bearing Ratio.

May 1, 2022

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

Wind turbines are subjected to complex form of cyclic loadings with variable amplitudes and frequencies. The cyclic loading and the accumulation of plastic strains with the number of cycles will result in degradation of the foundation soil stiffness. The foundation stiffness degradation will result in a shift (reduction) of the fundamental frequency of the wind turbine. Although this issue is recognized in the guidelines for wind turbines foundation design, no specific provisions are provided in the guidelines to consider the long-term stiffness degradation. In this paper, a practical procedure to consider the long-term cyclic loading effects on the stiffness of wind turbine foundations in cohesive soil is proposed. The procedure is based on 3D FEM modeling and reliable empirical methods to estimate the stiffness degradation due to the cyclic loading. Using the proposed procedure, the long-term performance of the P&H tensionless pier foundation with and without a reinforcing collar at the top of the pier is assessed. The numerical results demonstrated that the long-term performance of the P&H tensionless pier foundation with a reinforcing collar at the top of the pier is outstanding with negligible long-term degradation of the foundation stiffness.

Sep 8, 2021

By Jeffrey C. Schuh, Logan Bloemer, Daniel P. Dietzler

Over the past 30 years, the authors have encountered numerous projects where recognizing the geology, soil properties and groundwater conditions, and considering alternative construction techniques have promoted efficient and cost-saving construction. The construction documents for these projects, produced by various engineering firms, provided basic information on geotechnical conditions. The authors became involved in each project either because there was a problem during design or construction or, as a contractor, won the project because they saw a value engineering opportunity to take advantage of the geologic setting of the project to design and build alternatives to what the designer depicted. Understanding the geologic setting is critical before planning and designing begins. Being able to work with the geology and the materials on site is preferred before specifying more costly and complex solutions, which often require the importing of materials and adherence to unnecessary and/or inappropriate specifications. Failing to understand the geology or not knowing all the techniques available for construction can lead designers to develop solutions that could be inappropriate. This paper presents several examples of value engineering and project performance enhancements developed through knowledge of basic soil mechanics and implementing innovative solutions. History and Background Most people attend DFI meetings, present their experiences, listen to others, and read articles and papers with the hope they can learn from others. Geotechnical engineers and contractors often interface with others in the execution of projects who have, at best, a rudimentary knowledge of geology and soil mechanics. Of course, there is a need for architects, bankers, and regulators, etc., but they typically do not have much interest in the nuances of geotechnical engineering, which relies on both art and science. Thus, significant time is spent educating counterparts in the need for comprehensive subsurface investigation programs and the intricacies of construction in the “dirt,” as they typically refer to soil and rock.

Jan 1, 2019

By Bernard B. Vannoy, Howard W. Gault, Ramesh Bobba

"Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. This paper describes the methodology employed by the JV and USACE to evaluate the overlap, thickness, and position of the barrier wall. It addresses the contractual requirements, positional uncertainty, and evaluation procedures.These procedures evolved over the course of the project as various issues were identified and procedures developed to evaluate these issues. During the project, it became clear that the JV and USACE could ascertain that the wall thickness and overlap requirements could be met if the overlap based upon Koden data was at least 0.7’ in the left-right direction. For a small number of piles with overlaps between 0.5’ and 0.7’, the piles are contractually compliant yet contain a minor degree of uncertainty in the overlap. Initially, the USACE assumption was that the amount of uncertainty of verticality measurements would require more than a 1-foot measured overlap in the left-right direction to confirm an actual, contractual 6-inch overlap. With time and experience, the limit of measured overlap was reduced in accordance with greater understanding of the equipment capabilities and tolerances. Other lessons learned include the need for Quality Control/Assurance personnel to collect data at the same starting point for every pile.For every pile the JV and USACE compared analog and digital data to provide confidence that the correct digital data was used for overlap calculations. Perhaps the most important lesson learned was the importance of the JV and USACE working together and sharing all data. Overlap analysis was performed by the JV’s Barrier Wall Specialist and a small number of USACE personnel. This resulted in a high level of experience and expertise within a small group.IntroductionThe Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep, and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. The wall was installed through a 6-foot wide Protective Concrete Embankment Wall (PCEW) which was installed two feet into rock. The PCEW protects the embankment from erosion of drilling fluids during subsequent operations. Below the PCEW the piles were installed to a specified elevation (staggered at 475’ and 473’ below the 748.2’ work platform). The Ordovician limestone and shale bedrock is flat lying with few vertical fractures. These conditions facilitate the advancement of pilot holes with very low deviations (with considerable credit to the JV’s drillers and steering engineers). The pilot holes were spaced on 31.5-inch and 35-inch spacing. Subsequent enlargement of the pilot holes to 50’ resulted in a continuous wall. This paper addresses the requirements and procedures to assure that the wall was as wide, deep and continuous as specified."

Jan 1, 2015

By Silas C. Nichols, Jennifer E. Nicks

"Limit states design (LSD), or load and resistance factor design (LRFD), is a method to account for the uncertainty in loads and resistance through a reliability calibration that requires all applicable limit states (strength, service and extreme) to be checked during foundation design. LRFD has been in use internationally for several decades; however it wasn’t until recently that engineers working on highway projects were required to use the method for the design of highway bridges and other appurtenances. Although the bridge community has been using a form of limit states design for structural components since the early 1970s, the design of foundations for bridges, walls and other geotechnical features had long been performed using allowable stress design (ASD), whereby all uncertainty in loads and material resistance is combined in a single factor of safety. While the move to LRFD was viewed as a more rational approach for the design of bridges and structures, the transition to its use for geotechnical engineering has been met by many with confusion and difficulties in application. This article will revisit the history of transition from ASD to LRFD for geotechnical engineering, summarize the status of the transition and issues with its use, and briefly discuss some emerging research opportunities for improving and advancing the design platform.Background and HistoryUntil about a decade ago, foundations and substructures for bridges were traditionally designed using ASD, while the superstructure was designed using load factor design (LFD), a precursor to LRFD that incorporated factored design loads but no risk assessment. This combination led to uncertain and incompatible safety margins in design for the various bridge components. In 1986, the American Association of State Highway Transportation Officials (AASHTO) Subcommittee on Bridges and Structures (SCOBS) concluded that the standard bridge specifications in use at the time for U.S. transportation projects had significant inconsistencies and gaps, wasn’t up to date with emerging technology and that the development of new specifications was warranted. The proposed solution by the subcommittee was to transition to a more coherent method of design where applicable failure and serviceability conditions could be evaluated considering the uncertainties associated with loads and resistance."

Jan 1, 2015

By Patrick J. Hannigan, Seth Robertson, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) and the conventional Bi-Directional Load Test (“BDLT”) are full-scale load tests where loads are applied bi-directionally to the foundation element. The BDLT uses an embedded loading source consisting of a jack assembly with one or multiple hydraulic jacks located between two steel bearing plates. As the jack(s) within the jack assembly is/are pressurized, the plates receive the load from the jack(s) and transfer these loads to the foundation element. In the case of the TLBT, the loads are also applied bi-directionally to the foundation element. However, in the TLBT case, the loading source is located above the foundation head. With the TLBT’s non-embedded and reusable load assembly, the loads are applied to the foundation using the steel shaft bearing and base bearing plates cast within the foundation. These plates are connected to the load assembly at the foundation head via Grade 75 or Grade 150, threaded, steel bars. This paper presents comparison results from a full-scale load test performed by both bi-directional load testing methods on adjacent test shafts. Details regarding subsurface conditions as well as test shaft construction and installation are included for the comparison tests. Test results and corresponding analyses are presented and discussed in detail.

Sep 8, 2021

By Louay Owaidat, Daniel Jabbour, Allan Frappier, Jose Gomez, Mark Stanley, Tino Maestas

The U.S. Army Corps of Engineers (USACE) is implementing a levee strengthening program along the Sacramento River East Levee (SREL) designed to correct 11 miles of deficient levees as identified by recent hydraulic and geotechnical investigations. The first project, the subject of this paper, completed in 2020 resulted in approximately 3.0 miles of improvements to the California Central Valley Flood Protection system. The project area lies along the east bank of the Sacramento River in Sacramento. The program consists of constructing cutoff walls through existing levee embankments to remediate levee through seepage and under-seepage. Key challenges included designing and constructing measures to remediate a 100-year-old legacy levee system, the presence of both industrial and residential properties immediately adjacent to the landside of the levee creating severe space and access limitations, and performing this work during the 2020 statewide mandate to shelter-in-place due to the COVID-19 pandemic. The project team of contractors, USACE, state and local agencies, and engineering firms partnered to bring this project to successful completion within budget and on schedule expending more than 60,000 man-hours with no lost time accidents. With the issuance of future planned contracts, the program will significantly reduce flood risk to the City of Sacramento.

Sep 8, 2021

By David Chadwick, Paul Marsden, Chris Hughes, Mathias Delapille

"Following damage caused by the 2011 Christchurch earthquakes, the NZ$127.5million Christchurch Town Hall Restoration project is due for completion in 2018. The building is undergoing extensive repairs and a strengthening regime to meet New Zealand’s New Building Standard. One major aspect of the project is the stabilisation of the soil directly beneath the building using interconnected jetgrouting columns installed a cellular configuration, the purpose of this being to decrease the likelihood and severity of foundation movements caused by earthquake-induced soil liquefaction and lateral spreading. The soils encountered on the site ranged from cobbles and gravels through to sandy silts with a significant quantity of timber and rootlets. This wide variation of soil types presented a number of challenges with regard to effective and consistent treatment by jet grouting. The paper presents an overview of the quality assurance practices and also the testing regime adopted on this project.INTRODUCTIONMost of the deformation experienced by the Christchurch Town Hall structure over the course of the Canterbury earthquakes was caused by movement of the underlying ground. Two primary mechanisms of ground deformation were observed:- Liquefaction of the soils underlying the building foundation- Lateral spread of surface soils towards the free face at the river edge which runs 20 metres from the building. This mechanism also resulted in additional vertical settlement of the building foundations.The overall foundation design philosophy adopted by the project team for the Christchurch Town Hall Conservation Project has been to improve the ground directly beneath the structure to mitigate against these two mechanisms of ground movement. Additionally, a robust raft slab is proposed to distribute the foundation loading more evenly and increase the ability of the structure to resist lateral stretch of the underlying ground.The ground improvement system proposed by the Client’s geotechnical consultants, Tonkin &Taylor, comprised a cellular arrangement of interlocking jet grout columns, this arrangement would effectively encapsulate the soil within the cells preventing lateral spread.In total 1,097 interlocking jet grout columns, extending over the entire floor plan of the structure, were required to satisfy the design requirements."

Jan 1, 1900

By Deep Foundation

Whenever an organization launches an initiative, the question arises whether that initiative has staying power. Or is the initiative, as is quite often the case, merely a fad; that is, just an activity that suddenly becomes popular, but which does not stay popular for very long. When the Federal Highway Adminis- tration (FWHA) started its Advanced Geotechnical Methods in Exploration (A-GAME) initiative, that question was addressed, especially considering the fact that up to 50% of major infrastruc- ture projects suffer impacts to schedule or cost due to geotechnical issues. Many of these issues relate to risks identified directly or indirectly to the scope and quality of site character- ization work. Effective site charac- terization is critical for recognizing. potential problems that may affect design and construction and for ensuring safe, well-performing and cost-effective projects. Grounded on that, knowledge of all available site investigation methods should continue to be shared widely and the application of those methods should be encouraged on an ongoing basis throughout the project lifecycle. The A-GAME initiative covers five technologies: Cone penetration testing (CPT), monitoring while drilling (MWD), electrical geophysical methods, seismic geophysical methods, and optical and acoustic televiewers. Of these, three soil and rock investigation methods were highlighted that are underutilized not only here in the U.S., but also in many places around the world: CPT: a well proven and established method for soil characterization that turned 90 last year, in which continuous in-situ data are col- lected quickly and consistently. Geophysics: the science that assesses the physical properties of the soils and rock using seismic and electrical techniques, which con- tinues to advance in leaps and bounds as the application of well- understood technologies become more powerful.

May 1, 2023