Search Documents

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By S Zheng, Y Zhang, Z Wen, S Ma

Red mud (RM) is a solid waste product generated during alumina refinery process, and is usually stored in SFs (SFs) because it canÆt be disposed of easily. In this paper, environment degradation caused by RM-SFs was systematically assessed by the method of single factor pollution index based on the analysis data of water, soil and atmosphere sampled around one newly-built and one decommissioned RM-SFs, which are managed by an alumina production company in China. The results revealed that the ambient environment around RM-SFs is seriously polluted by alkali and mercury (Hg). The pH value of RM leachate, surrounding surface water and groundwater are all higher than the limit of water quality standards in China. And as a possible result of overflowing of high alkaline leachate, soil pH value for the decommissioned SF decreases with increasing distance between the sample collection points and the closest side of RM storage facility (RM-SF). Total Hg concentrations in RM leachate, surrounding surface water and groundwater all exceed Grade III limits of ChinaÆs Environment Quality Standards for Surface Water and Groundwater. However, the air quality was little affected as the daily average of TSP in the air is below grade II values of Chinese Ambient Air Quality Standard.CITATION :Wen, Z, Ma, S, Zheng, S and Zhang, Y, 2012. Assessment of environmental quality impacts caused by red mud storage facilities in China, in Proceedings Life-of-Mine 2012, pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Pollard DM, Willis GM

The removal of bismuth from liquid copper in a vacuum furnace was studied over a range of pressures. The rate determining step changes from diffusion in the gas at pressures above 0.2 Torr to approach the Langmuir evaporation rate at pressures of 10-2 Torr. Oxygen and sulphur were found to have a negligible effect on the rate. Bismuth removal from copper sulphide was found to be considerably slower than from copper. This is consistent with the known thermodynamic properties of ternary sulphide melts.

Jan 1, 1980

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

By Sturchio NC, Williams SN, Fischer TP

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma.. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these "primary" components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

By Sato S, Kawaguchi T

The granulation and bed-permeability of sinter raw materials depend on interactions between the properties of various iron ores and water. The properties of individual iron ores are controlled by their particle size distribu- tion and surface characteristics, which can be described by representative particle size and wettability, respectively. Added water may be absorbed, affect granulation or lower bed permeability. These effects were experimentally studied as a function of properties of the iron ores. A mathematical model was developed in order to calculate the granulated particle size and permeability using the known blend of sinter raw materials. The calculated results were in good agreement with the observed values.

Jan 1, 1980

The hydraulic backfilling of mine tailings has proven very successful at the Homestake Mine in Lead, South Dakota. It allows greater versatility, selectivity and safety in mining. It has also minimized surface subsidence and underground rock movement. The tight filling also eliminates underground fires. This paper explains the hydraulic backfill method used and the problems encountered by so doing.

Jan 1, 1973

By B Upton, J Mitchell

The use of hydro scaling and in-cycle shotcrete to replace conventional jumbo scaling, mesh and bolting as the primary method of ground control for run of mine development has been investigated through extensive trials at the Waroonga mine, Agnew Gold Mining Company.These trials have progressed from investigating the productivity aspects of the method through to a three month mine-wide trial, which may yet lead to the adoption of this potentially best practice ground control technique at Agnew.Ov erseas trials and research have shown that hydro scaling results in a significant improvement in the shotcrete-rock bond strength. Good adhesive bond strength ensures that the shear strength of the shotcrete layer rather than itÆs flexural or tensile strength is fully mobilised as rock mass reinforcement.This maximises shotcretes ground reinforcement capability and it is suggested that a bolt-less fibrecrete support design is feasible using the hydro scaling technique.

Jan 1, 2005

There are a number of mineral processing operations which produce at some point a stream of hot particulates. At today's energy prices it becomes important to recover the energy held in the hot particulates. Sometimes it is convenient to use gas, e.g. in air pre- heating, and this will be appropriate in some circumstances. There are cases where it would be very useful if energy in the hot processed particles could be exchanged to the cold feed solids. This can be achieved within appropriate limitations by countercurrent heat exchangers comprised of parallel channels which contain, alternately, fluidized solids of 'hot' and 'cold' streams respectively. A pilot- plant has been built. Some calculations relating to industrial application will be Presented.

Jan 1, 1981

By Kesser Z, Vincze T

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

By Bassett N

The Eneabba deposit, located 280 km north of Perth, Western Australia, and 30 km inland (Fig. 1) is one of the most recently developed deposits of mineral sands in the world. The area has been in production since 1974, while the Associated Minerals Consolidated Limited (AMA) operation commenced production in 1976. Total ore reserves of close to 400 million tonnes contain about 40 million tonnes of heavy minerals (proved and probable).

Jan 1, 1979

By Kuwasaki N, Mitsune Y

Many activity measurements of components in liquid oxides have been reported in the field of slag chemistry. However, very little is known about the thermodynamic behavior of compo- nents in oxide solid solutions. In the present paper, e.m.fs. of the follow- ing galvanic cells employing solid electrolyte Zr02(CaO) were measured on the entire range of composition of the solid solutions. Pt/Ni-(Mgl-x ix)O/ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mgl-xNix)2SiO./ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mg l-xNix)Si03/ZrO2(CaO)/Ni-NiO/Pt. Activities of NiO in these solid solutions of (Mgl_ Nix)O and (Mgl_ Nix) 2Si0a(where 0

Jan 1, 1980

By Guo-Zheng J

This paper describes the risk management strategies adopted to control unstable slopes in the east open pit of the Daye iron ore mine. Extensive experience has been developed over the last 35 years in the management of pit wall instability resulting in the successful excavation and reinforcement of pit slopes over 350 m in height.

Jan 1, 1994

The scarcity of truck tyres combined with decreases in the availability of labour, increases in fuel costs and a buoyant international economy driving project budget blowouts, have all combined to change the paradigm behind mining equipment selections. The escalation of commodity prices has occurred in parallel with an increasing maturity in continuous mining machinery, mobile in-pit crushing systems and very large-scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in-pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

Jan 1, 2007

Three separate and unconfined aquifers occur in the Hilton area, named relative to position in relation to ore horizons: Footwall Aquifer in the east; Ore-Zone Aquifer within the ore-bearing Urquhart Shales; and the Hangingwall Aquifer in the west.It is the on-going strategy it Hilton to drain the Ore-Zone Aquifer which occupies structurally- and sulphide-controlled leached zones in the steeply west dipping strata. The aquifer affects considerable ore reserves to 480 m below the surface. Dewatering began in 1976, and is essentially completed to 4 level (240 m below surface). Dewatering efforts are now based on 8 level (480 m below surface).

Jan 1, 1993

By K M. Cook, D Clark

Fatality prevention and zero harm are key focus areas for resource companies. However, they remain an ongoing challenge for high hazard industries, including the mining sector. As one example the latest International Council on Mining and Metals (ICMM) Safety Performance Report shows that, while there is generally a declining fatality trend since the organisation commenced publishing data in 2012, there were still 33 fatalities across member companies in 2022 (ICMM, 2023b). Every fatal incident brings significant pain and suffering to the colleagues, friends and family of those involved, however the failures and causal factors leading to each incident are frequently very familiar to people working in the industry, particularly those tasked with managing risk and safety. In the words of Dame Judith Hackitt, Grenfell Tower Fire Investigator, ‘there are no new accidents – just different people making the same mistakes because they haven’t learned’ (Hackitt, 2022). The recurring themes in terms of the nature of fatal hazards and their associated causes across the mining sector show that, despite improvements evidenced by the favourable declining fatality trends over the long-term (in general and outside of catastrophic multiple fatality events), changes are required to achieve fatality elimination and the aspiration of zero harm. This extended abstract and the accompanying presentation apply a mining frame of reference to the idea that there are no new accidents, examining how this applies within the industry and why the lessons from past failures are not always well understood or applied to prevent the reoccurrence of material unwanted events. Many contemporary mining and resources organisations have extensive internal incident history data and a wide variety of information on fatality incidents is publicly available, including the annual ICMM Safety Performance Report. This extended abstract and the accompanying presentation explore how this existing data can be used effectively to learn from the past and proposes practical ideas regarding strategies for successful knowledge transfer to the workforce as a key component of preventing history repeating and improving safety performance across the industry. As noted by ICMM, ‘sharing lessons from failure is vital to improving health and safety, but it’s not enough’ (ICMM, 2023a).

Apr 16, 2024

Miners and mineral explorers are concerned at the increasingly hostile environment being generated towards their industry and their profession. There is little official or public recognition that the mining industry is essential for the maintenance of the country's standard of living; a large part of this hostile feeling is caused by the assumption that mining destroys large tracts of our attractive countryside. This paper presents a historic review of the impact on the countryside of the major land using groups commencing with the Polynesian migration. European farming practices, subsequent expansion of the urban dweller and the land management practices of the two Government Departments, Lands and Survey and New Zealand Forest Service who between them control half of the total land area, are discussed. Estimates of total land area to date, directly and indirectly affected by mining have been calculated and a broad estimate of 18 000 ha or 1/1500 of total land area is indicated; current annual mineral production requires some 240 ha. These gross areas take no account of subsequent land rehabilitation, its improvement upon the original in some cases and the recreational, historic and aesthetic areas gained. Comparisons are then drawn with some current land practices in New Zealand.

Jan 1, 1977

Four data sets are required to put constraints on the tectonic evolution of the southern rim of the Pacific Ocean basinI . data bearing on the dispersal of the major Gondwanaland continental fragments and the birth of the Southern Ocean,2. data bearing on the interaction of the Pacific Ocean basin lithosphere with the South American, Antarctic, and Australasian continental masses,3. data bearing on.the evolution of the Scotia Sea floor, and 4. data bearing on the evolution of the various continents, microcontinents. and volcanic arcs.

Jan 1, 1990

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

By S Phinn, V Glenn, P McKenna, P D. Erskine, D Doley

The key goals for mine site rehabilitation require mine managers to demonstrate that rehabilitation is safe, stable, self-sustainable and non-polluting. Within this context, it is reasonable for stakeholders to expect that mine site rehabilitation is resilient to disturbance impacts such as fire and drought. However, mine managers actively avoid fire on rehabilitation; and as a result have limited understanding of fire behaviour on revegetated landforms, the long term implications for site stability and the potential risk to site relinquishment. An experimental fire that was conducted at the Curragh Mine site in May 2015, burnt 117 ha of 19- to 21-year old mine site rehabilitation, mimicking wildfire conditions and creating a mosaic of fire impacts across the landform. Using a combination of ground surveys and remote sensing assessments, we demonstrate that over a two year period, ecological metrics such as species richness, woody density and understorey biomass all recover to pre-fire levels for both grassland and open woodland areas. This is supported by WorldView-3 satellite imagery and the remote sensing assessment using the differenced Normalised Differenced Vegetation Index (dNDVI) which shows high regrowth within the burn area in 12- and 24-month image captures. The results suggest that within the recorded conditions, this site is resilient to fire impacts, and has the capacity to recover to pre-fire levels within the first two years following the fire.CITATION:McKenna, P, Erskine, P D, Phinn, S, Glenn, V and Doley, D, 2018. Measuring the recovery of coal mine rehabilitation following fire in Queensland using remote sensing and ground surveys, in Proceedings Life-of-Mine 2018, pp 141–146 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018