Search Documents

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra rake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDR listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Paul Miranda, Corby Anderson

"The Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently obtained a Mineral Liberation Analyzer (MLA). CAMP has utilized the technology for several projects with excellent results. The MLA is able to both analyze size and quantify mineral phases. Therefore, the MLA is becoming the Sherlock Holmes of the mining and metallurgical industry. For this presentation, four projects have been evaluated and data was collected using the MLA. The first project involved tungsten mine. Previous mining practices have yielded poor tungsten results and recoveries. By using the MLA, tungsten mineral phases, along with possible contaminants, were verified and the results used to try to increase overall tungsten recoveries. The second project evaluated a molybdenite/chalcopyrite concentrate with surprising results. The third project is a silver project. Initial flotation scoping tests were performed by attempting to separate silver from gangue material. Because of the poor recovery results (less than 5%), MLA was used to determine possible scenarios for increasing silver recovery. Finally, the last project involves gold evaluation in tailings. For all projects, MLA application results will be presentedand discussed.INTRODUCTIONThe Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently received a software add-on to a scanning electron microscope (SEM) located at Montana Tech. The Mineral Liberation Analyzer (MLA) technology was developed by Dr. Ying Gu of the JKTech Center of the University of Queensland. Since August 2006, CAMP has received and processed over 50 samples. These samples include a total mineralogy of tungsten ore samples, gold tailings, lead zinc tailings pile, molybdenite concentrates, copper concentrates, as well as others. During analysis of these received samples, the technology allows the samples to be quantified mineralogically with some surprising results.For analysis, the samples were initially sieved between 170 to 200 screen sized mesh. This ensures that received samples mineral size is fairly uniform. The samples are then placed into epoxy and allowed to harden. Next, the samples are polished and carbon coated for MLA analysis."

Jan 1, 2007

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

By Met M. E, Worner H. K

During the past two years, a large number of creep tests has been carried out on electrolytic lead, special assay lead and ordinary refined (Port Pirie) lead. Some of these tests have already been reported.1§ In addition, an attempt has been made to estimate the influence of the individual elements present in small traces in Port Pirie lead. The present paper gives the results obtained when small additions are made to "U" lead of the composition shown in Table 1.(which has been used throughout these investigations during the past few years). The additions were silver, antimony, bismuth and zinc. The results of the addition of tellurium have already been communicated. This investigation was intended to run parallel with a similar one using electrolytic lead as a basis and adding one element at a time.Actually, the experiments using "U" lead have got rather ahead of the others. The important point has emerged, however, that the effect of a .given addition may be appreciably influenced by the presence of traces of other elements.In most of these tests, an initial stress of 500lb. per sq. in. has been used. Whilst it is fully appreciated that this stress is higher than those used in practice, it has to be borne in mind that an improvement in creep resistance was *Manuscript received December 11th, 1936.

Jan 1, 1936

By T. Y. Chong, J. A. Folinsbee, M. Fullam

PJV Dome Mine has used some form of gravity concentration since start of milling operation in 1909 to recover free milling gold. Amalgamation and conventional jigs were first used and were replaced with the Knelson Concentrators in 1993. The Knelson concentrates produced were upgraded on a conventional shaking table prior to smelting and refining into gold bullion. In May 2002, a comprehensive review of the latest gravity recovery technology led to a piloting campaign aimed at further improving gravity recovery. The Knelson concentrates, subjected to intensive cyanide leaching in an Acacia pilot plant, were found to be amenable to intensive cyanide leaching with over 98% of the gold being dissolved within 24 hours. An Acacia Intensive Leach Reactor was successfully installed and commissioned in December 2002, to replace the shaking table. his paper describes pilot scale testing, installation, commissioning and optimization of the Acacia Intensive Leach Reactor. Also, the economic impacts on down stream processes are highlighted.

Jan 1, 2005

By John A. Mathews

It is a great honor to be asked by the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe was of brief duration—only one year—and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher— Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "aus-tenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I worked side by side with William Campbell

Jan 1, 1925

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

By D. J. Steynfaard

Sishen Iron Ore Mine is situated 280 km north-west of Kimberley in the Northern Cape Province of South Africa. The mine produces and sells high quality iron ore of various specifications to various national and international clients. The saleable product is derived from the blending and beneficiation of different types and qualities of hematite iron ore. This paper documents the new developments which were implemented (or are in the process of being implemented) on the mine in the long-term planning, medium-term planning, grade control and material tracking in the beneficiation plant with special attention being paid to the quality of the final, saleable product. The process starts with the long-term planning where the pit shell and pit optimization is determined by Whittle 4X. New developments include the introduction of a linear programming based scheduling system to enhance the long-term schedule generated by Whittle 4X. The LP route was decided on in order to take into account all the constraining factors of the final product that could not be configured in Whittle. To complement this the XPAC Auto Scheduler scheduling package was introduced to do the medium-term mine scheduling. This 18-month rolling plan includes cost parameters to enable the planner to extract a detailed operational budget from the scheduling while ensuring that production standards are maintained and grade constraints are met. The existing grade control system was enhanced with GPS capabilities and a computer system to do material tracking. The high precision GPS system introduced on the shovels allows for the accurate control of the loading procedures at the mining face. Because of the complicated geology and grade composition of blasting blocks it is imperative to accurately differentiate between different materials in the same blasting block and being able to excavate that with the loading equipment. The GPS system on the trucks allows for accurate location monitoring of dumping in order to keep track of specific material types. The state-of-the-art material tracking system developed for Sishen will enable the grade control officer to keep track and record various parameters of the material from its in situ position in the blasting blocks, through the crusher and onto different stockpiles, in various stages of the beneficiation process and onto the blending beds, into the dispatching trains and eventually into the ships for international distribution. These developments elevate the Sishen planning and grade control systems to a new level of service excellence from which management can obtain accurate and timely information on product status. It also enables Sishen to maximize resource utilization while still complying with the tough market constraints.

Jan 1, 2003

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By Grey CA

Any economic evaluation of a lead-zinc mining project requires the estimation of net revenue per tonne of concentrate at the "mine gate". The value at the mine gate equals the Net Smelter Return minus all realisation costs. The paper develops a simple predictive model for Net Smelter Return based on metal prices.

Jan 1, 1990

By George D. Raitt

Anyone who has spent any time in and around the drilling and blasting profession knows that probably the most critical part is the drilling portion. A blasthole is nothing more than a cylindrical vehicle designed and strategically situated to hold and contain an explosive charge so that it can be detonated in the most efficient and optimum manner possible. It matters very little if the latest “State-of-the-Art” explosive or detonation system Is employed if the hole is poorly placed; i.e. excessive burden and spacing, sized incorrectly for desired results, insufficient in depth etc.. This is not to mention that the drilling phase is the most expensive, requiring sizeable initial outlays and upkeep. It’s also true that improper drilling can cause costs to skyrocket throughout the remainder of the work cycles such as excavating and hauling, crushing, screening and so on.

Jan 1, 1990

1. Domestic Production and Use: In 1980, 13 companies operated 33 primary aluminum reduction plants, with 3 firms accounting for 62% of production. Washington, Oregon, and Montana accounted for 30% of the total production; Texas, Louisiana, and Arkansas 19%; Tennessee, Alabama, and North Carolina 15%; other central and eastern States 36%. Based on published producer prices output of primary metal in 1980 was valued at over $7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 26% of domestic consumption in 1980, building 22%, transportation 21%, electrical 12%, consumer durables 7%, and other uses 12%.

Jan 1, 1981

By Frederic P. Dewey

The Bureau of the Mint of the United States Treasury maintains 13 ofEces for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, nine tables of comparative results, taken from the regular work of the service, are given..These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement in the assay-results, and follow through decreasing gold fineness and increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the agreement of the assay-results ; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these ire added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion,2

Jan 1, 1910

Studies were carried out to examine the effect of introducing varying levels of a pisolitic limonite (Yandi) into an Australian iron ore blend. Compared with other ores in the blend Yandi is more porous. This structure is found to have a considerable effect on the sintering behaviour of the blends. Pilot-scale sintering studies and plant trials showed that sinter plant productivity, sinter reducibility and the low-temperature reduction degradation index altered significantly when the level of Yandi in the ore blend exceeded 15 wt%. The improvement in the reducibility is thought to be a direct result of increased porosity in the sinter and the presence of highly reducible pseudo-relict haematite. Plant trials have also shown that operational changes could be made to the sinter plant to avoid potential deterioration of productivity

Dec 1, 1991

By J. Kunze, R. Degal

During the last 100 years, the submerged arc furnace has been one of the most amazing diversified melting units. These furnaces have found their application in more than 20 different main industrial areas such as iron, ferro alloy, chemical industry, lead, zinc, copper, refractory, titanium oxide, recycling, phosphorus etc. Such an evolution was only possible because of tremendous efforts in research and development and due to the large range of design solutions. The worldwide strong competition also forced the industry and plant suppliers to develop highly efficient, economically balanced units in optimized sizes and with long lifetimes, to adapt to the market conditions. Regarding the environment, the plants improved significantly in terms of water treatment plants and off-gas treatments as well as on site recycling units. This paper will give a short overview regarding the history of the furnace and the latest developments in today?s main application fields: ferro alloys, non-ferrous, special application and recycling. In addition new activities in research and developments are briefly discussed.

Jan 1, 2004

By J. R. Campbell

THE need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. WASHABILITY STUDIES The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money, can hardly be spent on "feed surveys" to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus.

Jan 1, 1928

By C. Richard Tinsley

INTRODUCTION The economic analysis (Chapter 3), the engineering studies (Chapter 10), the credit structure (and the consequential funding sources) - Chapter 11, and the overall feasibility structure for any venture are all directed to determining one major decision element: How much and how certain is the reward for taking these risks? Risk assessment is a surprisingly weak area of analysis and is usually addressed in a checklist fashion. It is much preferable to deal within a risk system so that the inevitable tradeoffs among risks are correctly made. DEFINITION The first step toward risk definition must be to ascertain all of the risks to which a project or a company is exposed; otherwise one will remain ignorant of the possibility of a financially crippling loss until it occurs. (Carter and Crockford, 1974). However, simply stating what "risk" is can lead to debate. For example, risk could be (adapted from Vaughan, 1982): -the chance of a loss - uncertainty of loss -possibility of loss - uncertainty -dispersion of actual from expected results - probability of an outcome different from the one expected - possibility of an occurrence of an undesirable contingency -a condition in which a possibility of a loss exists. For the minerals industry financier, the last definition is probably the most appropriate. However, from a mineral company's point of view the definition might well include the possibility of not achieving the expected financial return. RISK CLASSIFICATION Risk identification will be readily agreed as the all-important first step. There are five major "branches" of risk classification. These are: -Statistical -Modellers -Checklist -Project Financing -Insurance The Statistical set discovered probability theory and any risk discussion soon deteriorates into a mathematical jungle (Megill, 1977; Hartman, 1976; Reutlinger, 1970; and Pouliquen, 1970).Their use of terminology tells its own story: coin toss (binomial distribution), gamblers' ruin, delphi (oracle) techniques, monte-carlo simulations, random walks, etcetera. These techniques inadequately represent the judgements necessary in an increasingly complicated and interrelated world. The risk Modellers have turned to the computer to handle these inter-relationships but soon find barriers because of "simultaneity". Certainly the computer has its uses to conduct various analyses (marketed as "sensitivity" analyses) but very often one finds that this involves changing one or two variables at a time, all other things being equal. Unfortunately, in a modern and complex world all other things do not remain equal. The statisticians will, no doubt, jump to their own defence by citing this

Jan 1, 1985