Search Documents

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

O. S. GARRETSON, Buffalo, N. Y.: If I may judge from the half-tone illustration engraved from a photograph of this medal and accompanying Dr. Prazer's paper, I do not think the cast ing is exceptionally fine. I have often made castings of simi lar character which I think were equally good. For instance, I have taken a coin, moulded it directly in fine sand, and cast from it in Scotch (or the equally good, if not better, Ameri can Scotch ") foundry-iron a copy quite as sharp and smooth as the original. The secret is in using very fine sifted sand. In fact, I have used for this purpose the dust which had accumulated on the beams overhead in my foundry, riddling it with a very fine sieve before using it. ['NOTE BY THE SECRETARY.—After the session at which these remarks were made by him, Mr. Garretson cast at his Buffalo foundry, in the presence of a number of members of the Institute, copies of the bronze pin furnished to visiting members by the Local Committee of the Buffalo meeting. The accom panying illustration, Fig. I, has been reproduced from a photograph of such a casting, made in green sand, under the conditions of ordinary foundry-practice, and not subsequently polished in any .way. I can also certify that the photo graphic negative was not touched, to improve its clearness of definition, before the production of the " half-tone" plate from which Fig. 1 has been printed. As, in the case of the Kytchtym medal, it was the thin, ribbon-like sprue, rather than the low-relief features of the medal itself, which indicated the fluidity of the metal and the sharpness of the casting, so in this work of Mr. Garretson it is the long and slender pin which offers the strongest evidence of these qualities. It is scarcely neccssary to point out that the filling in the mould of a long and nar row opening, such as this pin presents, is the severest test that could be imposed upon the casting, and that the sharpness of the point of the pin in the casting is striking evidence of the success with which this test has been met. The Pittsburgh Testing Laboratory .has made for the American Manufacturer measurements of this casting and an analysis of the sprue. The thickness of the main casting is from 0.049 to 0.068 inch. That of the tag bearing the stamped number is 0.024 inch. The analysis, which represents the iron ordinarily employed by Mr. Garretson for thin castings, is as follows :

Jan 1, 1899

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By Emily Wortman-Wunder

As the 2010 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2010 issue of Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 328. A significant portion of the contribution that we as a professional society make is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable transfer of technology. Communication within the mining community is the key to a successful society. Through books, magazines, meetings and electronic media, we accomplish the technology exchange that is fundamental to the existence of the Society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, Pennsylvania, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume certainly fulfills that pledge. The 2010 Transactions is the first Transactions to take advantage of new publication technologies. It appears solely as an e-book. The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which will certainly better serve the mining community. I am excited about this development and the opportunities it presents. The 2010 Transactions also contain some of the most exciting research from the past year, including new developments in mineral processing, safety and exploration. Be sure not to miss the two Minerals & Metallurgical Processing issues on the subject of gold hydrometallurgy. This 2010 Transactions comprise of a total of 78 technical papers (582 pages including index), including all 21 papers (136 pages) that were published in 2010 in the Technical Papers Section of Mining Engineering magazine (Vol. 62) and all 34 papers (231 pages) that were published in 2010 in Minerals & Metallurgical Processing (Vol. 27). Addition, this volume contains 23 papers (194 pages) that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 78 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2010 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2010

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By W. T. Malone, J. R. Williams, R. L. Tiner, J. M. Tinsley

Hydraulic fracturing methods for production stimulation have become a common procedure in the oil and gas industry. Fracturing treatments are performed on wells of various potentials to help increase the production rate. In addition to the desire for increased production is the need to predict what increase might be expected. This knowledge is useful in economical treatment planning to accomplish the desired production goals for the well. Theoretical production increases due to horizontal radial fractures may be calculated using equations developed from mathematical analyses and electrical models.1,2,6 It also is possible to predict theoretical production increases due to vertical fractures using curves developed from electrical3 and mathematical models.8 However, these studies assumed that the vertical fracture height and the formation height were equal, which may not be true." In addition, the final fracture height through which fluid is produced may not be equal to the created height. The development of vertical fracture proppant transport relationships has made unrealistic the assumption that propped fracture height is equal to created fracture height. Through the use of published proppant transport equations,4'12 it is possible to calculate the height of a bed of propping agent deposited in a fracture of a given height. Assuming that the fluid flowing in the fracture moves through only the propped portion of that fracture (i.e., that the un-propped part of the fracture heals) it becomes essential to know how production increase varies with the ratio of propped fracture height to formation height. It should be recognized that future investigation may determine that the fracture does not heal completely and that a highly permeable channel exists over the deposited bed of proppant. The effect of this channel was not considered for the present study. The following analysis of experimental data allowed development of curves to determine theoretical production increases considering fracture height as a variable. Discussion In designing a fracturing stimulation treatment a number of variables must be considered. The size of the treatment, type of proppant used, proppant concentration, treatment fluid properties and well conditions are all factors affecting the dimensions and permeability of the fracture. Production increase due to a vertical fracture is affected by propped length, height, width and permeability of the fracture for a given set of formation conditions. Production increase may be defined as the ratio of production rate after fracturing to the production rate before fracturing at the same pressure differential, pe — pw. The producing rate in an

Jan 1, 1970

This paper presents the near-field rock damage owing to production blasting in limestone quarry in the western region of Japan. The study's purpose is to learn the mechanism of crack development due to blast vibration. In this study, blast vibration's magnitude was expressed with peak particle velocity (PPV) which was obtained based on seismographs recorded database. In attempt to pursue a research's purpose of this study, there were two considerable interests: near-field blast vibration propagation and prediction, and crack observed and prediction. Furthermore, with regards to considerable interest of the study, there were three essential aspects which were challenged, such as: monitoring and interpretation of seismic wave propagation in a rock mass near large explosive charge of production blast scale, measurement of blast rock damage in adjacent to blasthole, and determine critical value of PPV which may produce significant rock damage. In order to determine precision critical PPV, understanding correlation between rock damage with vibration level is firstly important to be done. This paper also discusses how to measure, detect and quantify near-field blast vibration and blast rock damage in adjacent to blasthole.

Dec 6, 2010

By Carolina Rouillon

El presente documento señala dos experiencias aplicadas en la mina Yanacocha y Pierina exitosas donde se emplea las geomallas como parte del mejoramiento de suelos blandos con la finalidad de distribuir uniformemente las cargas impartidas por los grandes equipos mineros hacia la subrasante de mina típicamente conformada por suelos con alto contenidos de limos y arcillas húmedas y saturadas. Asimismo, los beneficios obtenidos por usar las mallas, no se limitan al ahorro en costo material de relleno, sino que se logra un mejor desempeño- en tanto optimiza la superficie de circulación de los vehículos mineros, reduciendo los tiempos de operación, así como prolonga los períodos de reparación y mantenimiento.

Sep 21, 2013

By Harvey T. Gracely, Mark J. Woodhull

DURING the past few years a marked refinement has taken place in the design of electric power shovels for the mining industry, increasing their digging ability and speed of operation without adding to their total weight. The increase in pay load has been accomplished by a more rigid engineering analysis of shovel design, involving the adoption of new special alloy steels, new sections, and new welding methods. Emphasis has been placed on lightness with increased strength, which is most clearly shown in the front-end equipment where dipper, handle and boom are new in design, material, and construction.

Jan 1, 1938

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By L Mottola

Three decades ago mining companies, principally in North America, aided by machine and explosive manufacturers, started significant attempts to develop and implement automated mining systems, mainly underground. These tended to be motivated by decreasing cost, increasing productivity, reducing labour requirements, and improving safety. These are important business drivers, however, little attention was given to the underlying goal of mining automation, namely to bring upstream processes in control and reducing variation, as seen in downstream mineral processing plants.This paper first reviews the nature of Lean Thinking and its application in the context of the growing commitments by industry to develop future automated mine production systems. The paper then makes reference to prior and current experiences in open pit blasthole drill and shovel performance monitoring, to demonstrate the principle that machine performance data offers as a means, not only to characterise the dynamic geological and working environment, but also to provide a foundation for automation. In this case, drill and shovel monitoring was originally motivated as a means to optimise blast fragmentation through more effective drill and blast designs that are based on an accurate determination of the bench geological and geotechnical characteristics, hence managing variation in the drilling and blasting process. This paper considers how automating and integrating such components of the mine production system would bring processes into a controlled state, creating value at the face, within a framework of Lean mining.

Nov 22, 2011

By M. Schmidt, P. Nord, M. Larinkari

Cathode stripping machine technology has been developed significantly both in electrorefining (ER) and electrowinning (EW) applications in the last ten years. The main driver has been robotic cathode handling, which has enabled increased flexibility to meet different layout and material handling requirements for both ER and EW processes. Additionally, cathode stripping stations have been continuously developed to optimize speed and to reduce mechanical stress of permanent cathodes. 'taco' type cathodes have been proven as beneficial approach for high capacity operations (particularly in Cu ER), where over 600 cathodes per hour continuous throughput has been achieved. However, the latest developments also apply to split type cathode stripping. Besides material handling, the modern cathode stripping machine has also an important role to provide information for production and quality monitoring. This paper describes the latest developments from the field of copper cathode stripping based on several different projects implemented in the recent years. INTRODUCTION After introduction of the permanent cathode technology in the late 1970s, it became the prevailing technology in copper refineries over the traditional starting sheet process by the end of 1980s. The main driver was less labour-intensive production due to fewer processing steps required along with more automated electrode handling equipment (cathode stripping machine, anode preparation machine, anode scrap washing machine and tankhouse cranes). Since then the design of the cathode stripping machine has followed the development of permanent cathode technology. The main development steps so far can be summarized as follows: Full Deposit Stripping Machine (FDSM) based on waxed permanent cathodes or cathodes with bottom edge strips resulting in split cathodes (copper sheets separated, see Figure 1) Wax less cathode stripping based on V-groove on bottom of the edge strip resulting in either ‘taco’ cathodes (enveloped copper sheets, see Figure 1) or split cathodes Full Deposit Robotic Stripping Machines (FDRSM) using 1–5 robots for permanent cathode handling and cathode stacking.

Jan 1, 2019

By William H. Langer

The annual consumption of sand and gravel aggregate in 2006 in the Phoenix, AZ metropolitan area was about 76 Mt (84 million st) (USGS, 2009), or about 18 t (20 st) per capita. Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix are mined and processed to provide some of this aggregate to the greater Phoenix area. The Agua Fria drainage basin (Fig. 1) is characterized by rugged mountains with high elevations and steep stream gradients in the north, and by broad alluvial filled basins separated by elongated fault-block mountain ranges in the south. The Agua Fria River, the basin?s main drainage, flows south from Prescott, AZ and west of Phoenix to the Gila River. The Waddel Dam impounds Lake Pleasant and greatly limits the flow of the Agua Fria River south of the lake. The southern portion of the watershed, south of Lake Pleasant, opens out into a broad valley where the river flows through urban and agricultural lands to its confluence with the Gila River, a tributary of the Colorado River.

Jan 2, 2010

On June 4, Kennecott Utah Copper (KUC)marked the centennial of the founding of the original company. Bill Champion is president and chief executive officer of KUC. He said, “What has happened during the past 100 years far surpassed even the most optimistic visions of men like Daniel C. Jackling and Robert Gemmell when they promoted the concept of mass production techniques for a low-grade deposit of copper ore. At that time, it was a totally new way of doing things and the mining leaders of that day scoffed at the idea. They said it would never work,” Champion said. The company will celebrate this once-in-a-lifetime occasion with a few special projects, mainly for the benefit of our employees, said Louie Cononelos, director of government and public affairs for KUC. The company has designed and minted a commemorative copper coin that reflects early steam shovel and locomotive operations on one side, and today’s modern electric shovels and huge haulage trucks on the other side. “The history of the company stems from the ores of the Bingham Canyon Mine. That coin has been encased as part of a10-panel brochure that captures the company’s 100 year history,” he said. KUC also developed special centennial banners and comparable framed posters that were displayed throughout its operations and at selected community locations that have enjoyed a long-time partnership and special relationship with the company. Some of the plants also designed their own centennial hardhat decals.

Jan 1, 2003

By Timothy A. Clancy

To help reduce the Nation's dependence on imported chromite, the Bureau of Mines is conducting research on the use of dolomites as an alternate material. Dolomite is a plentiful domestic resource and offers certain advantages as a refractory raw material. A review of the literature has indicated that there are many sources of high-purity dolomite in this country and that European nations use a greater proportion of dolomite refractories, primarily in steelmaking, than the United States, The Bureau of Mines characterized 14 domestic dolomites as to chemistry, density, mineralogy, microstructure, and thermal behavior, to develop baseline data on their suitability as refractory raw materials.

Jan 1, 1983

By B. G. Russell

A wide range of minerals is found within the Republic of South Africa, many of which are exploited to a greater extent than in similar deposits found elsewhere. It is often asked whether this is atributed to the high grade of the ores encountered in this country, or whether such factors as fiscal and Infrastructural incentives create an economic climate that has en bled the mining industry to successfully extract and market minerals at a profit. This paper views South Africa's mineral resources in a regional and global context In an attempt to place the country's geological wealth in perspective. It represents the author's own Views, and not necessarily those of the Department of Mine al and Energy Affairs.

Jan 1, 1986

By AIME AIME

AT Williams College, in the quaint old New England town where people still go to the post office for their mail, an interesting institution has come into being as one of the aftermaths of the peace conference at Paris in 1919. The war taught the world many things about economics although much remains to be learned and more to be appreciated. B. M. Baruch, H. A. Garfield, president of Williams, and others who took part in the conference at Paris or in preparation for it, feeling that benefits would accrue from informal friendly discussion of the problems that lead to political differences between peoples, called together a summer conference in 1920. This has now become an annual affair and is coming to be looked upon as an important center for developing and stimulating public opinion. Membership in the Institute is by invitation and the lists change to correspond with the particular subjects taken up. Each year a number of distinguished foreign public men are invited to be the guests of the Institute and to meet men and women from various parts of the United States interested in their special subjects. Round tables, general conferences, and public lectures are the means employed to bring out discussion. The first are organized by groups, each including usually 25 to 40 people interested in a special subject and meeting three times a week for informal discussion. Teachers, writers, economists, engineers, business men, indeed men of all vocations and many shades of opinion, are brought together. Once a week each round table presents in general conference with the members of all other groups the more general conclusions reached in its own decisions. Afternoon and evening lectures are given by the foreign guests and these are open to the public. The lectures and the general conferences are reported widely in the press but the proceedings as a whole are not printed, no resolutions are passed, and no action is taken or contemplated. The whole plan is to furnish a forum for free discussion in hopes that the difficulties of various groups and peoples may be taken up sympathetically and good understanding promoted. There is no creed, doctrine or dogma to which the Institute is committed and widely different views are currently presented. The constant effort is to bring out points of view and the reasons for them rather than to build up convincing arguments favourable to a specific action

Jan 1, 1926

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010

By S Worden, P A. Kirsch, A Kirsch

Despite the current downturn, coal remains an important commodity in the Australian economy. Increasing coal resource development has resulted in increasing competition for land use in coal mining regions across the country with communities and other stakeholders becoming more adept at articulating their concerns regarding this competition in a range of traditional and social forms of media. In this environment, obtaining and maintaining a social licence to operate (SLO) is problematic and has been identified as the fourth greatest risk facing the international mining industry.This research presents the findings from a longitudinal study on how Australian newspapers frame the views of coal mining stakeholders across each stage of the coal mining life cycle. News stories from national, state and regional newspapers in 2000, 2006 and 2013 were analysed.Over the study period, there have been significant changes in the coal mining themes being covered by Australian newspapers, the number of stories being published, the number of newspapers covering coal mining stories, and the diversity of stakeholders being quoted. How do the dominant themes in media communication change over time? How do these changes impact mining across the life-of-mine?The research confirmed that Australian journalists use framing, priming, labels and bias to conceptualise and understand the events that they report, and that this behaviour has a profound effect on public opinion.CITATION:Worden, S, Kirsch, A and Kirsch, P A, ?2014. Moving beyond economic framing of the Australian coal industry, in Proceedings Life-of-Mine 2014 , pp 365–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014