Search Documents

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961

INTERNATIONAL conferences on safety in mines originated in 1912 when, in response to an invitation issued by the United States, representatives of Austria-Hungary, Belgium, France, and Germany participated in a conference held in Pittsburgh, Pa The record shows that a permanent organization was proposed to be developed through. diplomatic channels. However, the advent of war 2 years later prevented this proposal from coming to fruition. No further cooperation between the Bureau of Mines and a group having: similar interests in a foreign country took place until 1924, when formal cooperation with the Safety in Mines Research Board of Great Britain was established. Interchange of personnel and results of research under that arrangement have resulted in a number of publications in both countries and more rapid advance in knowledge than could have been obtained through the same efforts exerted independently.

Jan 1, 1950

By E. H. Boyle

The Bureau of Mines has evaluated the potential availability of silver from 436 mines and deposits in 41 market economy countries (MEC?s) comprising five major economic categories of deposits: predominantly silver deposits and predominantly zinc, lead, copper, and gold deposits. This study evaluated the long-term cost and availability of primary silver production from 53 producing and 13 nonproducing predominantly silver properties in 11 MEC's and estimated the total recoverable silver from 370 properties as a coproduct or byproduct of zinc, lead, copper, or gold production. This study resulted in estimates of a demonstrated resource of 5.99 billion tr oz of recoverable silver as of January 1984. Of this total, 23.5 pet is in the 66 mines and deposits classified as predominantly silver properties. The largest quantity of recoverable silver, 43.9 pct, lies in the 121 properties classified as predominantly zinc, with 26.5 pct in 120 properties classified as predominantly copper, 4.1 pet in 21 predominantly lead properties, and 2.0 pct in 108 predominantly gold properties. At current silver prices, the economics of silver production favor silver that is a byproduct or coproduct of zinc, lead, copper, or gold, and much of the silver production in the United States from the predominantly silver mines is at an economic disadvantage in comparison with silver production in other countries.

Jan 1, 1986

By M. I. Brittan

Cyanide leaching of two West African gold ores was studied in multiple laboratories to provide process-engineering data for plant design purposes. Unusually slow leach extraction kinetics were observed using routine cyanide leach test procedures with pregnant solution monitoring. Carbon-in-leach testing, however, showed normal rapid kinetic behavior, with the same ultimate gold extractions being reached in much shorter elapsed times. Kinetic curves based on washed solids assays also exhibited more typical leaching characteristics. The results bore all the hallmarks of some equilibrium inhibition of the leaching. It was surmised that ore gangue components were responsible for weakly adsorbing gold-cyanide complex reaction product, thereby holding up soluble gold in the solid phase. The term ?preg-borrowing? was coined to describe the reversible phenomenon and distinguish it from irreversible preg-robbing. The two ores investigated may represent an extreme form of a more general effect that in most instances might pass unnoticed. The effect can lead to misinterpretation of kinetic leach curve data and underestimation of calculated ore head grades.

Jan 1, 2008

By Rodger C. Fry

Underground coal mining has been active within the East Mountain property since the mid 1950's. As a result, coal from two seams has been extracted within large areas allowing surface subsidence to occur. Monitoring of subsidence annually, began in 1981 using on the ground conventional monumentation, surveying and photogrammetric monitoring. The data collected has shown the time benefits of photogrammetry and the relationship between observed subsidence and the geometry of the mined out area below.

Jan 1, 1986

By Timothy W. Ellis

Wire Bonding is the dominant IC interconnection process presently used in the semiconductor assembly industry (1). The flexibility, adaptability and cost of wire bonding will continue to keep it as the key process for the interconnection of integrated circuits to substrates. However, wire bonding still has certain technological hurdles to overcome if it is to continue following the semiconductor roadmap (2). Particular issues which need to be addressed include low overall tensile strength, low elastic modulus, low shear per unit area and mechanical loop stability of Gold based micro-alloys. The ability to produce ?Deformation Process Metal-Metal Matrix Composites? (DMMCs) is based upon the deformation nature of immissible metallic systems. For reference, the Gold (Au)-Molybdenum (Mo) phase diagram is shown in Figure 1 (3). By inspection of the diagram, Au has a very low solubility for Mo, while Mo has essentially no solubility for Au. This is the metallurgical analog of oil and water. In the Au-Mo case, this is particularly troublesome when producing precursor ingots of the alloy to be formed into wire products. In Table 1, the melting points and densities are shown for Au and Mo. As shown, the melting point of Mo is significantly higher than Au, and is very close to the boiling point of Au (2856°C). However, Au?s density is higher than that of Mo. As such, conventional casting techniques are not suitable, since solid Mo would float off the surface of an Au melt thus depleting the matrix of its alloy addition. In this work, two-phase composite wires were produced by deformation processing to develop an interconnection wire with elevated tensile strength, modulus and shear to those commonly available in the market (4). This technology has been used previously in the production of high strength electrical conductors particularly for high field pulsed magnets (5).

Oct 1, 2003

By Donald W. Breck

Zeolites were first recognized as a new group of minerals by Cronstedt with the discovery of stilbite in 1756. The word zeolite was coined from the two Greek words meaning "to boil" and "a stone" because of the loss of water when heated in the mineralogist's blow pipe. (1) In 1845 it was discovered that certain soils have the power of retaining ammonium Salts. (2) These were the first ion exchange experiments. Later it was discovered that it was the hydrated silicates in the soil that produced this phenomenon and several years later a paper was published dealing with the action of dilute salt solutions on silicates which showed that this base exchange principal, which we now call cation exchange, is reversible. The quantitative cation exchange behavior of zeolite minerals, such as chabazite, was studied. As a result any aluminosilicate which exhibited the property of ion exchange was referred to as a "zeolite;" even today the term has been applied to clay minerals as well as synthetic organic ion exchange resins.

Jan 1, 1973

By Eleanor Abshire

This bibliography is the second in a series that covers the current technical literature relating to the metallurgy of zirconium. The rapid advance in zirconium technology makes it mandatory that abstracts be prepared and compiled as soon as possible to have maximum value; therefore, the information in this volume is not arranged chronologically. As a service to research and production groups, succeeding bibliographies will be issued as new acquisitions accumulate in the Zirconium Information Center sponsored by the Department of the Navy, Bureau of Ships and the Bureau of Mines at the Bureau's Northwest Electrodevelopment Laboratory, Albany, Oreg. The initial volume, Information Circular 7771, Bibliography of Zirconium, covering 969 abstracted reports and 645 United States and foreign patents, was published in April 1957.

Jan 1, 1958

By D. A. Singer, J. C. Griffiths

"One of the most useful approaches to a complex problem is to model the system which gives rise to the problem and to perform simulations through the model to find appropriate solutions. The Engel Model may be used as such a simulator to investigate the problem of the exploration for natural resources.The Engel Model is based on a two-stage search procedure in which a known area (A) which contains m prizes is subjected to search by n coverings. During the first-stage search the sensor system records signals which may be a response from prizes (that is, true signals) or may be false. Signals tend to cluster around a prize and a cluster size consists of s signals. If a circle of radius R is drawn around each signal some will overlap and the overlap from s signals contains a prize. The cost of a single covering in which each point of the area comes under observation once, is designated E1. Second-stage detailed search is expensive and is confined to areas of overlap of s circles; it leads to the location of prizes. Second-stage search of the whole area costs Ea units. The expected value, V, of a prize is known and its development cost is E3 units.The sensor system characteristics are defined by the circle of radius R around a signal, which should be small compared with the total area A and enters the model as a parameter a x R2/A. The probability of a false signal during a single covering of a circle of radius I is a known constant, A.This model was applied to the search for uranium ore bodies using two different types of occurrence. In the first, the Wyoming Basin type, the area is relatively large (A = 1 496 square miles) and a few (m = 4) large prizes occur (expected value V = $30 million). In the second area, which represents the Ambrosia Lake region of New Mexico, the area is smaller (A = 212 square miles) and contains many (m = 200) smaller prizes (expectedvalue of a prize V,$2 million). The three costs, E1, E2, E3, are adjusted to the different circumstances in the two areas.Simulations were performed using n = 1 to 40 coverings with cluster sizes s = 0 to 19; the radius R was varied from 0.52 to 3 miles (and, therefore, a = 0.002 to 0.133 0, respectively, dependent on the area of interest). The value of A was varied from 0.01 to 0.10.Profitable programs were found over a wide range of the parameters; the two areas required different strategies to achieve maximum profit. In the Ambrosia Lake region a few passes (n = 4 to 6) with small cluster sizes (s = 2 to 6) are more profitable, whereas in the Wyoming Basin region a large number of passes (n = 35 to 40) and cluster sizes of s = 5 to 10 are most profitable.As pointed out by Allais (1957) the larger prizes are the most important in deciding the successful outcomes of exploration programs, and the profit margin in the search for a few large prizes is sufficient to yield success over a wide range of programs. Such programs require very large investments if they are to be successful.To refine the Engel Simulator as a decision-maker in selecting the most profitable exploration programs it is necessary to obtain firm estimates of the sensor system characteristics, that is, of R, a and ? (lambda)."

Jan 1, 2014

By Michael L. Wayman

Archaeological and ethnographic work during the last century has shown clearly that metals have played a small but important role in prehistoric Arctic cultures. For at least the past several millenia both iron and copper have been used in the North, primarily for blades, projectile points, knives, awls, engraving tools, fishhooks, scrapers and axes. In addition they were used for joining purposes as staples and rivets. It is of great interest to enquire into the origins of these metals. In this connection one begins with the observation that to date there has been no clear evidence for the smelting or melting of metals in the Arctic prior to the arrival of Europeans. This can be explained partly by the absence of traditional pyrotechnologies such as the high-temperature firing of ceramics and the heat treatment of bone and wood. Another factor which surely inhibited the development of smelting/ melting operations is the relative absence of wood in the region. The production of charcoal for smelting requires large quantities of wood, to the extent that the desertification of a number of areas in the Old World is believed by some to have been at least partly caused by charcoal production. In the North this was obviously not possible. Thus the Arctic peoples were restricted to using native (naturally occurring) metals and metals obtained by various direct and indirect forms of contact with areas of the world where smelting was practiced. Both of these sources were important in the case of iron; we know that meteoritic iron, telluric (native) iron and smelted wrought iron were all used in the Arctic. These three types of iron will be considered in tum.

Jan 1, 1999

By J. W. Thompson

That the governor is hereby authorized to appoint a commission of seven persons, to be known as the industrial accidents commission-two of whom shall be employers of labor, two of whom shall be employees in either mines or industrial establishments of this Commonwealth, or duly accredited representatives thereof, two of whom shall be learned in the law, and one of whom shall be a person skilled and experienced in making investigations-to inquire into the causes and results of industrial accidents in the mines, mills, factories, stores, and upon the railroads, street railways, ships, wharves, and in all industrial establishments, and in all other places where men, women, and children are employed in manual labor in this Commonwealth; to study the most advanced methods for safe-guarding against these accidents; to inquire into the subject of fair compensation for those who are injured in these accidents, and for the families of those who shall be killed as a result thereof; and to study the operation and effect of the Workmen's Compensation Law of 1913. SEC. 2. The chairman of said co~mission shall be designated by the governor, and the person named on said commission as a skilled and experienced investigator shall be the secretary of the commission, The commission shall have power to employ such legal counsel and other officers and employees as it may deem necessary to properly perform its duties. SEC. 3. The secretary of said commission shall receive an annual salary of $2,400 and his actual necessary expenses; and the other members of the commission shall receive no compensation for their services, but shall be allowed their actual traveling and other necessary expenses. The salaries of any other persons employed by the commission shall be fixed by it.

Jan 1, 1920

By Jochen Petersen, Diane Taggart

"At an average of 90.3% (for the period of 1 January 2009 to 30 September 2011), Zincor’s zinc recovery was well below the industry standard of 96%. The losses through the residues, in particular the iron residue, were the biggest contributors to the overall zinc loss. It was believed that this loss could be decreased with the implementation of seed recycling. A plant trial was run to test the implementation of a seed recycle. The rate of seed addition through recycle was increased over a 4-week period. The presence of seed decreased the insoluble zinc loss by providing additional surface area for iron to precipitate onto, and reducing coating of unleached neutralising agent. The soluble zinc loss was also decreased at low and moderate seed recycle volumes. The improvement was attributed to agglomeration growth of the recycled particles, which improves the dewatering characteristics of the precipitate. In contrast, the soluble zinc loss increased at high seed recycle rates. This result was attributed to particle crowding and a low wash ratio.INTRODUCTION The Zincor refinery, which closed in December 2011, was situated just outside of Springs in the Gauteng Province of South Africa and employed the conventional Roast-Leach-Electrowin process, which accounts for 75 to 80% of the annual primary zinc production in the world. The refinery fed up to 220 000 t/a of zinc sulphide concentrate. The major portion of the raw material was sourced in Southern Africa from the Rosh Pinah and Black Mountain mines. Between 20 000 and 40 000 t/a of material was imported to make up the deficit and to improve the grade of the feed material. The iron contained in the zinc concentrates, at an average of 6.03% (for the period of 1 January 2009 to 30 September 2011), resulted in the formation of zinc ferrite during roasting, which is insoluble under atmospheric leach conditions. At Zincor, most of the zinc ferrite was dissolved in the residue treatment plant at elevated temperature and high acid strength. The leach liquor from this aggressive leach contained between 15 to 30 g/L of iron, mostly in the ferric form, and was known as the hot iron solution (HIS). The presence of iron in the liquor had an adverse effect on the zinc operation, particularly on the current efficiency in the electrowinning circuit. Therefore the iron needed complete removal."

Jan 1, 2016

In response to increased aluminum demand, U.S. producers have begun reactivating primary aluminum capacity which was shutdown during the 1974-1975 recession. Reynolds Metals Company started up almost 80,000 tons per year of idled capacity at Listerhill, Alabama, and Jones Mills and Arkadelphia, Arkansas plants. Howmet Aluminum Corporation and Alumax announced that the operating rate at their jointly owned facility at Frederick, Maryland was being increased from 75 percent to 100 percent, equivalent to a 44,000 ton-per-year increase in output. Kaiser Aluminum and Chemical Corp. expected to restart one of the two idled potlines at its Mead, Washington facility in May raising its production rate by 27,000 tons per year. ANTHRACITE - The anthracite market for the larger sizes continues at a good level, and although the demand for industrial sizes has been weak, the current trend indicates an increased demand for industrial fines by the steel, auto, and other industries.

Jan 1, 1976

Explosives identification tagging refers to the addition to explosives, during manufacture, of coded microparticles that can survive detonation, be recovered and decoded, and allow the explosives to be identified and traced to the last legal possessor as a result of distribution records kept of the coded tagged explosives. This study seeks to prepare the way for National implementation of identification tagging of all dynamites and cap-sensitive slurries (also known as water gels) by resolving technical issues and by developing a plan for pilot testing of the program. It is presented in two volumes: Volume I, National Implementation Model, and Volume II, Pilot Test Plan.

Jan 1, 1977

By O. P. Hood, R. H. Kudlich

When a gasoline locomotive is used in a mine there is danger of the noxious gases of the exhaust vitiating the air, but if enough air is circulating in those parts of the mine in which the locomotive is used, these gases are so diluted that they are rendered harmless, and the health of the workmen is not affected. In some mines the use of gasoline locomotives is impracticable, though in the majority of mines where they have been tried they have proved to be safe and economical. To determine the limitations that should surround the use of these machines in mines so that they shall not be detrimental to health and so that their economic advantage may be retained, it is necessary to ascertain the volume and the character of the exhaust gases and the amount of these gases that may be safely allowed in the mine air, and also to determine safe conditions of operation. The problem is primarily one of ventilation and like all ventilation problems must be intelligently computed to meet the conditions of each mine. The investigation described in this bulletin was undertaken 'by the Bureau of Mines in an endeavor to obtain exact information on some of the basal questions involved in the use of gasoline locomotives in mines, this investigation being one of many that the bureau has been conducting in its efforts to increase safety and efficiency in mining.

Jan 1, 1915

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner's representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

This report is in partial fulfillment of Contract S0241051 awarded to COMINEC on June 27, 1974. 'Me purpose of the work under this contract is to develop a conceptual design for an automated longwall mining system. The conceptual design will serve as the basis for future design and development of an automated longwall mining system capable of sustained production in excess of 2,500 tons per shift with reduced manpower which will ultimately be demonstrated in an area where conventional longwall mining has been successful. 1.2 DEFINITION OF THE PROBLEM 1.2.1 Why An Automated System The most obvious benefit of automation and remote control in a longwall mining system is the reduction of accidents consequent upon a reduced working force in the hazardous face areas. However, another important aspect of the problem is the skilled labor shortage which is being compounded by the need for vastly increased coal production. The United States coal mining industry had a working force of almost 600,000 miners in 1928 but was able to muster only 145,000 miners in 1970. The miners required to staff the additional working sections and the new mines necessary to meet our energy needs are simply not available. Only automation and remote control will permit a reduced work force with increased production by keeping the face equipment operating continuously.

Jan 1, 1975

By S. James Campbell

Ladies and Gentlemen: Never in the history of our mining industry has the emphasis on public relations been accelerated as much as it has in the last few years. Knowing of your keen interest in this subject I consider it a great privilege that your program committee has asked me here to discuss the crushed stone segment of our industry approach to this important part of our daily business lives. As you are aware, crushed stone operations are present in almost every segment of the country wherever aggregates for construction projects are required. The tonnage of crushed stone produced is second only to sand and gravel - another source of aggregates - and this together with sand and gravel amounts to over half of the tonnage of all mined products in the United States. What is unique about this industry that will be of interest to all of you in analyzing how they have approached Public Relations? The fact that it is so wide-spread is of course obvious, but perhaps a more significant nature of this segment of the mining industry that has brought it more in the limelight of public interest and on a larger scale is the location of a large part of the quarries quite close into the urban area and population centers where you have the greatest demand for aggregate products.

Jan 1, 1969

By William K. Connor, O&apos

The U.S. Bureau of Mines (USBM), in cooperation with the American Society of Mechanical Engineers (ASME), conducted over 200 hours of melting tests to vitrify residues from five municipal waste combustion facilities. Combined residues (grate residue and f1yash) from three municipal waste combustors, a waste water treatment sludge combustor, and flyash from a refuse-derived-fuel (RDF) boiler, were sequentially melted in a I-metric-ton (mt) water-cooled-wall electric arc furnace. Each of the residues underwent magnetic separation, screen size analysis, and bulk chemical analysis prior to melting. The furnace products were examined by optical and electron microscopy and by X-ray diffraction. Bulk chemical analyses were acquired for the metal, fume, and vitrified furnace products. The material balance for the furnace operation indicates that from 69 to 86 pct of the feed reported to the vitrified furnace product, which had leaching potentials well below the EPA limit for each metal, as determined by the EPA TCLP. The electric arc melting furnace currently is being utilized in a cooperative research project between the USBM and the Idaho National Engineering 'Laboratory (INEL) for melting tests on simulated low-level radioactive wastes,

Jan 1, 1991