Search Documents

By Richard D. Hagni

Microscopic examination of selected, representative, unweathered samples of Birmingham, Alabama, Silurian, sedimentary iron ores has fully revealed the nature of the phosphorous-bearing mineral grains. The grains are composed of carbonate-fluorapatite (collophane), range in size from 1 um to 2.25 mm, and exhibit varied types of intergrowth with hematite. Modal analyses conducted under cathodolumi-nescence have provided quantitative data on the a3undance of each of 15 types of phosphorous-bearing mineral grains and made it possible to assess the potential phosphorous liberation from four types of iron ore. The results indicate that 27% of the total phosphorous contained in the iron ores in the western part of the Birmingham district can be expected to be liberated by fine grinding; 60% for ores in the eastern part of the district.

Jan 1, 1982

By J. L. Jambor, H. W. Nesbitt

Oxidative dissolution of pyrrhotite and pyrite is largely responsible for the sulfate-rich waters of the vadose zone in the Waite Amulet tailings. Although the shallowest of the sulfate-rich waters are of the Fe-SO4 type, they change to Mg-SO4-type, near-neutral waters within 1-2 m of the tailings surface. Phyllosilicates and amphiboles are the only minerals present in sufficient quantity to ameliorate the amount of acidity produced. X-ray diffraction and microscopic studies of bulk sample indicate that quartz, chlorite, talc, amphiboles, magnetite, albite, and micas are the major and minor non-sulfide minerals, but their variations with depth do not give clear indications of depletion in the vadose zone. Mineralogical and bulk chemical compositions of the tailings confirm that Fe2O 3 has accumulated in large quantity in the vadose zone, with the Fe having been derived from Fe sulfides. When the effect of Fe2O3 is accounted for, the bulk compositions suggest that SiO2 is slightly more abundant in the vadose zone than in the saturated zone. This may be the result of residual enrichment of siliceous minerals such as quartz and albite in the vadose zone. Weathering of the tailings since the cessation of deposition in 1962 has resulted in a well-defined zone of sulfide depletion and secondary sulfate-mineral development. Although some silicate dissolution is indicated by pore-water compositions, the role of silicates in providing neutralization seems to have been minimal. The contribution by silicate minerals in laboratory tests of neutralization potential may be excessive relative to that in natural settings.

Jan 1, 1999

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By P. S. Arthur

The ISASMELT? process is a submerged lance smelting technology operating in smelters in Australia, the USA, Belgium, India, Germany, Malaysia and China. Further plants are under construction in Peru and Zambia. Following the invention of the Sirosmelt lance technology Mount Isa Mines recognised the commercial potential in the novel top blown bath smelting process and embarked on a development program that has lasted more than 25 years. After successful operation of pilot plants and demonstration plants producing copper and lead, Mount Isa Mines decided to license the technology to external companies. Since the purchase of Mount Isa Mines by Xstrata in 2003, Xstrata Technology has assumed responsibility for transferring the technology to ISASMELT? licensees. In the 15 years since the first commercial furnaces started operation plants have been constructed (or are under construction) with a combined annual smelting capacity of more than six million tonnes of concentrates or secondary raw materials. Process development continues on the commercial scale plants at Mount Isa and elsewhere. Many of the improvements implemented by plant operators have been passed on to, and adopted by, other licensees. Exchange of ideas and technical improvements occurs through ad hoc visits to fellow licensee sites and through regular licensee workshops arranged by Xstrata Technology. This paper updates the reader on the status of various ISASMELT? plants either operating or under construction. It highlights the important role that the technology provider?s operational experience plays in ensuring that new smelting plants ramp up quickly to nameplate capacity.

Jan 1, 2006

By Michael J. Nicol

Growing environmental and occupational safety concerns about the use of cyanide in gold processing has increased the interest in more acceptable alternatives. The most likely of these is thiosulfate. However, the thiosulfate process lacks a proven in-pulp method of recovering the dissolved gold, because activated carbon is not effective for the absorption of the gold thiosulfate complex .. Anion exchange resins do offer a possible route for in-pulp recovery. This paper describes work aimed at the evaluation of the effectiveness of commercially available anion exchange resins for the recovery of gold from thiosulfate leach liquors? and pulps. It has been found that strong-base resins are superior to weak-base resins in that they have a larger capacity, which assists in reducing the competition from other anions within a leach solution. Further studies with a selected commercial strong-base resin have shown that competing polythionateanions (particularly tri-and tetrathionate). Lower the maximum possible gold loading but that gold is selectively recovered over other base metal anions in solution. Kinetic experiments found that while? competilig anibns did not affect the initial rate? of gold loading it was important to minimise the contact time of the resin in solution so to prevent displacement of loaded gold by competing anions over longer times. A small-scale resin-in-pulp plant investigation showed gold can be recovered from a leach pulp by a strong-base resin to yield gold loadings of 3000 mg/L, barren pulp containing less than 0.05 mg/L of dissolved gold and. copper loadings of 500 mg/L. Loaded copper was displaced gold and at a loading of 2000 mg/L gold the copper loading was minimal «500 mg/L). The resin was found to recover gold adsorbed on the solids that would, otherwise have. reported to tails if a solid/liquid separation method were used. A patented two-step elution process in which copper and then gold are separately eluted from the resin is also discussed.

Jan 1, 1998

By C. J. Newman

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes? made to accommodate the increased SO2 gas strength resulting from the higher smelting rates.

Jan 1, 1992

By Lauri Holappa

Copper converting is mostly performed in Peirce-Smith converters. The process is still very similar to the original one developed in the early 20th century. It is a batch process in a horizontal cylindrical reactor with air blowing via tuyeres along the length of the reactor side. The Peirce-Smith converter has its roots in Bessemer's inventions in the 1850's as he tested both horizontal and vertical vessels for steel converting. However, for steel making a vertical pear-shaped converter with air bottom-blowing was established. In the course of time, there was a distinct necessity for oxygen usage instead of air due to harmful effects of nitrogen to steel properties and its cooling effect. In-bath blowing of oxygen did not succeed, however, and top-blown oxygen converter with oxygen lance (LD or BOF) was first developed in he 1950's and emerged rapidly to a dominating position. Somewhat later oxygen bottom-blowing via special shrouded tuyeres was developed (OBM or Q-BOP) but has attained only fractional share. Bottom-blowing technique had, however, impact on the current combined blown converters which adopted the benefits of both top and bottom blowing. In copper converting Peirce-Smith type converters have kept their position until today although new processes have been introduced and at least few of them seem to be emerging. In one respect copper converting has a clear leading position i.e. in the progress of continuous converting processes (Mitsubishi, Ausmelt). These processes utilise top-blowing lances instead of in-bath blowing tuyeres. A different principle for continuous converting is flash converting by Kennecott Outokumpu, which makes smelting and converting independent of each others. Solid ground matte is used as a feed for flash converting in a reactor shaft similar to Outokumpu matte flash smelting. A comparable process has been presented by Inco too. The paper discusses principal physico-chemical and process technical similarities and differences in copper and steel converting. Although these processes are metallurgically quite different it seems that during the modem history of ferrous and non-ferrous metallurgy, starting from the 1850's, the exchange of knowledge between these disciplines has been quite intensive. In long-term perspective, many similarities in the development can be found but also divergences due to different ambient circumstances.

Jan 1, 2003

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Jie Li, Zhongliang Tian, Xun Hu, Kai Zhang, Yanqing Lai, Hongliang Zhang

The Al-Sc Alloys show many advanced properties for a wide range of engineering applications. But the metal Sc must be added into the metal Al in the form of the Al-Sc master alloy, which is usually produced by the thermal reduction process. In this paper, the decomposition voltages of Sc2O3 and Al2O3 in Na3AlF6-K3AlF6-AlF3 melt were calculated based on the Nernst equation. And the Al-Sc master alloy was prepared in the melt at 950°C by electrolysis. The results show that the Al-Sc master alloy can be prepared by the co-deposition of Sc3+ and Al3+ at the cathode if the concentration ratio of Sc2O3 to Al2O3 in the melt is more than 2:1 under the condition of the aluminum electrolysis. SEM and ICP analysis of the product indicates that the Al-Sc master alloy is made of the phase Al and the phase Al3Sc.

Jan 1, 2016

By Kun Wang, Xinhui Li, Huaqing Xie, Qingbo Yu, Qin Qin

"Three typical model compounds of bio-oil (ethanol, acetone and phenol) were studied in the steam reforming process for hydrogen production. In the thermodynamic analysis, the three componds showed the similar trends. The hydrogen yields increased with the increase of steam/carbon (S/C) ratios, and the temperatures of the maximum hydrogen yields moved afterward to low temperature zone. However, the hydrogen contents were just about 70%. For improving hydrogen yield, a new system for steam reforming of bio-oil with site CO2 capture was put forward. This system required the catalst with the larger granularity having greater mechanical strength and higher abrasion resistance. So, six Ni-base catalysts loaded on Al2O3 particles prepared were used and among them, Mg-Ni/Co catalyst showed the best catalytic performance. For the simulated bio-oil (the mixture of the compounds), the hydrogen yield can attain 63% with Mg-Ni/Co catalyst with the good stability and regeneration ability.IntroductionCurrently the interest in the use of hydrogen as a clean energy carrier is increasing, and the main way for producing hydrogen is steam reforming of fossil fuels, containing steam reforming of nature gas, naphtha and coal. But this way caused substantial amounts of CO2 emitted, and these sources of hydrogen which are non-renewable energy will eventually be used up [1, 2]. As a kind of renewable energy, biomass is recognized as an attractive alternative to fossil fuels, because of its neutral CO2 emissions [3]. There are mainly two thermochemical processes using biomass to produce hydrogen, gasification and flash pyrolysis followed by steam reforming (SR) of the biooil produced in the flash pryolysis process [4]. The latter was known as one of the most promising and economically viable methods for hydrogen production [5]. In the last decades, the biomass flash pyrolysis technology was adequately developed and fairly mature [6]. But the steam reforming of bio-oil is still at the research stage and yet has been leading to more and more concerns by the researchers. In their research, the catalysts were widely studied and yet mainly were powdery[7-10], and the reactors manily were fixed bed reactors[11-13], readly causing the carbon deposition and the catalyst deactivation, against the continuous running. In this paper, a new systerm was put forward and could realize continuous production of hydrogen, yet needed catalysts with the larger granularity having greater mechanical strength and higher abrasion resistance, as well as powdery CO2 sorbents which mainly calcium oxide based ones.In this paper, the thermodynamic analysis of the steam reforming processes of three typical bio-oil model compounds (ethanol, acetone, phenol) was performed, and the effect of S/C ratio and temperature on the hydrogen yield and the compositions of gaseous products were investigated. Then, a new systerm for steam reforming of bio-oil with site CO2 capture was put forward, and the catalysts with a certain granularity were prepared and studied."

Jan 1, 2014

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to 'improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992

By T. Shibaraki

A new larger, more efficient and economical Mitsubishi furnace line at Naoshima was put into operation in May 1991. Naoshima Smelter had produced previously about 230,000 mtpy anode copper with two smelter lines, i.e., a conventional reverberatory furnace line and Mitsubishi furnace line, which had been shutdown at the same time of the start up of the new smelter. At the beginning of the operation, there were several initial problems at the area of off gas trains and feeding system. By overcoming them now the process has been continuing satisfactory operation at the design rate. The paper describes about the design concepts and the actual operation of the new smelter.

Jan 1, 1993

By Fathi Habashi

The recovery of uranium from wet process phosphoric acid was applied on industrial scale in the 1940's by using octylpyrophosphoric acid as an extractant. Later, more efficient reagents were used, e.g., di(2-ethylhexyl) phosphoric acid and actylphenyl phosphoric acid. In the 1970's the rare earths in Kola phosphate were recovered in Finland and recently (1997) in Norway using HNO, as a leaching agent and di(2-ethylhexyl) phosphoric acid as solvent. It was demonstrated later on laboratory scale that both uranium and rare earths could be extracted from the rock by tributyl phosphate but at different pH values provided that the rock is leached with nitric or hydrochloric acids instead of the commonly used sulfuric. This new concept opens the way to the possibility of treating phosphate rock by in-situ, dump, or vat leaching for the recovery of phosphate values as well as uranium and the rare earths. Another solvent extraction process is used industrially for the purification of phosphoric acid using butyl and amyl alcohols.

Jan 1, 1998

By A. J. van der Zeeuw

The use of SME 529 in the extraction of copper from acidic liquors and of copper and nickel from ammoniacal solutions, is illustrated with results of laboratory and bench scale mixer/settler experiments. Special features of SME 529 are its high loading capacity and the ability to keep the complexes dissolved in the organic phase up to quite high concentrations.

Jan 1, 1976

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about 10 minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag-carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By F. Garcia-Carcedo

This research aimed to develop a clean technology for the production of ZnO from residues generated by the steel making industry. Scientific and technologic parameters were both investigated in order to define an industrial methodology allowing the integral recycling of EAF dusts. A reengineering of the Waelz process was perform,~d, aiming to produce a clean fraction of ZnO, fluorine free, as well as a slag enriched in metallic iron, which can be recycled in electric arc furnaces. The technical conditions used to produce the ultra pure fraction of ZnO are described. The magnetic separation of the EAF dust allowing the production of a phase high in iron and recyclable to the electric arc furnace is also discussed. Thermodynamic of the volatilization of all the elements contained in the EAF dust was performed in order to better control the thermal process in the rotary kiln. Tests were run using different reducing agents, weakly or highly reactive, aiming to determine their specific efficiency.

Jan 1, 2000

By B. C. Blakey

Unlike most hydrometallurgical slurries, those containing significant concentrations of goethite are typically highly viscous and shear-thinning, even at solid volume fractions below 5%. The viscosity may also depend upon time. These characteristics must be taken into consideration in slurry transport and heating. The technical literature is replete with apparent contradictions regarding the viscous behavior of these slurries, which may be due, in part, to variations in viscosity-measuring techniques. We present techniques that yield consistent results suitable for use in process design. A striking degree of time-dependent behavior is demonstrated for a laterite slurry. Reliable methods to design and analyze tubular transport and heating systems for time-independent slurries are summarized. Rules of thumb are then offered to account for the effects of time-dependency.

Jan 1, 2000

By Patrick R. Taylor

Ilmenite concentrate and methane are fed to a non-transferred arc thermal plasma reactor to produce a powder that is primarily TiC and Fe. This material has promising characteristics for powder metallurgy applications. Free energy minimization plots were used to predict the feasibility of the reaction. An estimate of the optimum molar ratio between the ilmenite concentrate and methane was made based on the mineral composition. Argon-helium mixtures were used as plasma gases. The effects of power input level, carrier gas flow rate, powder feeding rate, and methane-ilmenite molar ratio were studied and the behavior of the system characterized. Two different powder injection angles were tried. A mathematical model to describe the temperature profiles in the reactor was formulated and solved. The product has been characterized by x-ray diffraction and atomic absorption. A conversion of 97 % of Ti to TiC was achieved. It was found that minor amounts of titanium oxides, iron carbide and free carbon are also present. TEM and SEM were used to study the morphology.

Jan 1, 1996

By Jiayan Li, Yi Tan, Yao Liu, Yaqiong Li, Shenrui Wu

"A metallurgical grade silicon (MG-Si) refining concept process was presented. Under vacuum conditions, silicon was selectively oxidized by high purity silicon dioxide to form gaseous silicon monoxide while impurities with low vapor pressure in MG-Si were rejected in residue; Then high purity silicon was obtained from the disproportionation of condensed silicon monoxide; and by-produced silicon dioxide was recycled for the oxidation step. Thermodynamics on boron rejection during the oxidation were studied in this work. In the temperature range of 1200-1800K, the saturated vapor pressure of boron, and the Gibbs free energy changes, the equilibrium partial pressures of silicon monoxide and boron oxides of potential reactions were calculated. And the effect of boron activity in MG-Si was also discussed. The results indicated that boron in MG-Si can be rejected during the oxidation and it showed the potential for the further development of the new refining process.IntroductionAs global energy consumption growing dramatically, higher prices of energy and global warming problem have attracted more and more attention [1]. As a clean and renewable energy industry, the photovoltaic (PV) industry converts solar energy to electricity using solar cell device and has a growth rate of about 30% in recent years. It has caused a shortage of silicon feedstock due to that about 90% of solar cells are made of crystalline silicon. And high energy consumption during the production of silicon material, i.e. solar grade silicon (SoG-Si), is main obstacle for its mass production."

Jan 1, 2012