Search Documents

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By Chengxian Lui

Detailed mineralogical and metallurgical investigations were carried out on a phosphorous-bearing manganese carbonate ore from the Huayuan manganese mine, Hunan, China. Microprobe analyses indicate that the Manganese occurs mainly in calc-rhodochrosite and in rhodochrosite. The cOll'pOsitional range of these manganese carbonate minerals is 50 -80 % MnOJ3, 0 -35 % CaOJ3, 5-35 % MgC03 and 0 -15 F~. The manganese carbonate minerals are very fine grained, IOOSt are between 4.6 and 9.4 1m in diameter. The small grains are clustered into aggregates that form bands 0.5 to 10 rnn wide. The phosphorous-bearing mineral in the ore is fluorapatite and is in grains that are generally smaller than 6 1m in diameter. Metallurgical tests show that it is possible to concentrate the aggregates of manganese carbonate minerals by high intensity magnetic separation, and to reduce the phosphorous content by rpasting the concentrate to convert the manganese carl::x>nates to insoluble hausmannite, and then leaching the roast product with HCI to dissolve the fluorapatite.

Jan 1, 1989

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015

By Y. W. Chung, W. I. Chia

"The interaction of water vapor with single crystal Ni3(Al,Ti) and polycrystalline Ni3Fe, with and without the presence of oxygen, has been studied with Auger electron spectroscopy, photoemission spectroscopy, thermal desorption and isotope exchange. Water dissociates to produce atomic hydrogen above 200 K on both Ni3(Al,Ti) and Ni3Fe surfaces. For Ni3(Al, Ti), the reaction is structure-sensitive. Pre-adsorbed or co-adsorbed oxygen on Ni3(Al,Ti) and Ni3Fe significantly suppresses hydrogen production due to water dissociation. This suppression process occurs more efficiently on Ni3Fe than Ni3(Al, Ti).IntroductionOrdered intermetallic compounds such as aluminides, silicides and titanides are very attractive for structural applications at high temperatures. This is because these intermetallics tend to form adherent oxides in oxidizing environments which protect the base materials from excessive oxidation and corrosion. In addition, they have low density, relatively high melting points and good high-temperature strength. However, the moisture in air severely embrittles many ordered intermetallics such as FeAl [1-3], Fe3A1 [4,5], C03Ti [6,7], (Co,Fe)) V [8], Ni3Si [9], Ni3(Si,Ti) [10], Ni3(AI,Mn) [Ill, and Ni3A1 [12-14], resulting in low 'ductility and brittle fracture at room temperature. Recent studies by Liu and coworkers (see review by George and Liu [15]) provide a qualitative description of the mechanism for this moisture-induced embrittlement. During elongation testing, cracks are formed, thus exposing fresh alloy surfaces. One or more active components of the alloy react with water vapor in the environment to produce atomic hydrogen which penetrates into crack tips and causes hydrogen embrittlement. This is similar to that proposed for moisture-induced embrittlement of aluminum alloys [16]."

Jan 1, 1996

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996

By Adolfo Pillihuaman Zambrano

Fe-Cr-C production is a very high electrical energy consuming process. Decrease up to 10% of this electrical energy is expected when self-reducing agglomerates are used. This research aims to understand how the synergetic effects are when stronger reductant, like Fe-Si, is substituted for coke in self reducing pellets. Brazilian chromites containing 41.2%Cr2O3 were mixed with petroleum coke and agglomerated with cement as the binder. Small amounts of 1%, 2% and 4% of Fe-75%Si were substituted for the equivalent petroleum coke, and pure silica plus hydrated lime were added for adjusting the slag composition. The mixture was pelletized, dried and submitted at 1773K up to complete the reactions. The results showed that the reduction reactions were 1.4 and 2 times faster with 1% and 2%Fe-Si addition, respectively, than with no addition. The microscopic analysis showed that it was formed a liquid phase, but the pellet did not collapse what indicates that the coalescence of the metallic phase depends on the dissolution of the pre-reduced particles of the chromites into slag.

Jan 1, 2008

By Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Jian-jun Hu

It could significantly increase the leaching rate of refractory gold concentrate containing sulfur and arsenic by roasting pretreatment with adding certain amount of sodium sulfate, and the mechanism of that was systematically researched with DSC, XRD and SEM in this paper. Results indicated that the mechanism of Na2SO4 on double refractory gold concentrate at roasting pretreatment can be summed up in the following three aspects：Firstly, Na2SO4 can react with SO2 and SO3 which is produced by the oxidation of sulfides and generate Na2S2O7(l), which plays buffer effect on sulfides exothermic oxidation, avoiding the secondary-encapsulated of gold. Secondly, the liquid phase of Na2S2O7 can cover mineral particles' surface that possesses a sintering effect, it leads to internal cracks of the particles. Finally, mineral particles will gather with sodium sulfate particles as the center that can improve the permeability of the layer.

Jan 1, 2015

By C. Flores

A novel process using solid metals for the direct reduction of more noble metal ions from solvent extraction organics has been developed. Base metals recovery has been the principal focus of investigations to date but feasibility tests have now also been made on galvanically stripping selected precious metals. In this study gold (III) was loaded from an aqueous HAuCI4 .3H20 solution into a mixed organic 40 vol.% TBP, 10 vol. % D2EHPA in kerosene. The direct precipitation of metallic gold from the loaded organic phase using zinc powder and iron, aluminum and copper slabs at 70 °C was successfully demonstrated. The gold reduction rates were relatively fast even though the conductivity of the organic solutions is very low. The reaction rates were studied as a function of the variables zinc particulate size, oxygen and nitrogen atmosphere, water content in the organic phase, organic ratios and temperature. The gold morphology was usually powdery or dendritic in nature but continuous films were obtained in some instances. Activation energies were calculated and possible reaction mechanisms are discussed. In general, the results obtained were very promising and showed that gold can be successfully cemented from selected organic solvents by galvanic stripping using less noble solid metal reductants.

Jan 1, 1995

By S. Yabe

The reinforcement of the annual copper production capacity to 330,000 metric tons has been attained at Saganoseki Smelter & Refinery in 1991, which is one of the largest and most efficient custom smelters in the world. Many operational improvements and technology developments have realized the increase of smelting and refining capacity without adding main facilities to the existing process. The blister copper refining and anode casting process is composed of two 400 tonnes anode furnaces and one double-wheeled casting machine with the capacity of 80 tonnes per hour. The great innovations in this process such as the finding of essential issue on the extending of anode-mould life and the development of a new anode-mould casting machine have raised the operation efficiency by 14% Now, the process is producing 38,500 tonnes per month of best quality anode in well- controlled working condition, and anode productivity per worker increased by 52%. The progress in extending anode-mould life, the mechanism of the new anode-mould casting machine and the increase of efficiency in butane reduction, that were the principal parts of many technological improvements, are described in the present paper, including some operation results.

Jan 1, 1993

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.

By K. Murayama, M. Kawakami, T. Takenaka, S. Yokoyama

"Cokes play an important role of spacer in blast furnace. However, they degenerate during Boudouard reaction. Blast furnace cokes are reacted with pure C02 at I 072 to 1673 K. Reaction rate was obtained by the weight change of spherical specimen. The specimen after reaction was examined by microscopic observation. The reaction rate increased with temperature and was expressed by two Arrhenius type lines. The activation energy was 126 KJ/mol at higher temperature than 13 73 K and 202 KJ/mol at lower temperature range. At the higher temperature range, the reaction proceeded from the surface leaving unreacted core, whereas homogeneously whole inside at lower temperature. The porosity increased from the center to surface at higher temperature, whereas it was almost constant at lower temperature.IntroductionThe cokes have the function of fuel, reductant and spacer to keep gas and liquid flow in the blast furnace. Thus, the reaction mechanism of coke with several gas and the strength after the reaction should be important factor to control the blast furnace operation. The reaction mechanism of coke with C02 has been studied extensively. The rate equations were derived by Gadsby[ I], Ergun[2] and Turkdogan and Vinters[3]. They were compared and discussed by Kobayashi and Omori [ 4]. Effect of crystallization degree on the reaction rate was examined by Kashiwaya and Ishii[5]. Catalytic enhancement effect of ash componets have been clarified by Kashiwaya et. al. [6]. Although degradation of coke in blast furnace has been examined recently[7], however, the degradation of coke after the reaction with C02 has not been well clarified yet. In the present work, the metallurgical coke specimen was heated in N2 and C02 and the reaction mechanism and degradation behavior after the reaction was investigated."

Jan 1, 2000

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to simulate nickel flash smelting process. In the nickel flash furnace, oxidation of concentrate occurs at one end, and reduction of slag occurs at the other. The model makes use two zones, namely the reaction shaft/settler zone and the appendage zone and accounts for 6 phases (matte, slag, silica, magnetite, Cu-Ni alloy and gaseous phase), 13 elements (Ni, Co, Cu, Fe, S, 0, N, C, H, Si, Al, Mg and Ca) and 33 chemical components in nickel flash smelting system. The compositions of matte, slag and gaseous phases in equilibrium are calculated by using the data of free energies of formation and activity coefficients of components. Two nickel sulfide species are used to allow for the modeling of sulfur-deficient mattes. The model predictions are compared with the known industrail data from Kalgoorlie Nickel Smelter, and excellent agreement is obtained. The model can be a very useful tool for monitoring and optimizing the actual industrial operations of nickel smelting process. The distribution behaviors of Ni, Co, Cu, Fe, S and 0 in the nickel smelting furnace depend on the process parameters such as smelting temperature, volumes of air, the content of the elements~ charge and oil.1. IntroductionThe nickel flash smelting furnace essentially consists of a reaction shaft where nickel sulfide concentrate is partially oxidized with air, a settle zone where matte and slag are allowed to separate, and a slag cleaning end where coke is added to provide for the reduction of the oxidized nickel from slag, and electrodes are used to provide heat.The theoretical model to consider a mass balance for copper flash furnace is developed by S. Goto and R. Shimpo[1][2J. However, this can not be true for nickel flash furnace as a whole since oxidation of concentrate occurs at one end (in the reaction shaft/settler), and reduction of slag occurs at the other (in the appendage). Despite these limitations, an acceptable pseudo-thermodynamic description of the furnace can be achieved using essentially two zones, namely the reaction shaft/settler zone and the appendage zone. Compositions of gas, slag and matte in two zones are calculated."

Jan 1, 1998

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO Zn(g) + COl. This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction 2Fe2+ + ZnO = 2Fe3+ + Zn(g) or 2FeO + ZnO = Fe2O3 + Zn(g) does not occur at an appreciable rate, as is expected from thermodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide concentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By Flávia Paulucci Cianga Silvas, Otávio da Fonseca Martins Gomes, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Guilherme Apostólico Bortolini, Stoyan Gaydardzhiev

"Printed circuit boards (PCB) are particularly problematic to recycle because of the heterogeneous mix of organic materials, metals, and glass fiber. PCBs are found in almost every electroelectronic equipment and their recycling process involves a pre-treatment to separate the products which contain targeted metals. In this work, a physical processing involving sequential shredding and hanuner milling were used to obtain a comminuted sample from scrap printers PCBs. The thus prepared sample was analyzed for particle size distribution and by optical microscopy as well was subjected to pyrolysis, leachabilty and chemical composition determination by XRF. The metals concentration was determined by ICP and AAS. The PCBs have been also analyzed by SEM-EDS (micro-analysis and X-ray mapping). The results show that the studied PCBs are lead free, multilayer with 4 copper layers, have 45% of metals and the copper is present in significantly higher concentration than the rest of the metals.IntroductionThe global generation of e-waste (electrical and electronic equipment waste - WEEEs) grows at a rate of about 40 millions of tons per year [ l].Among this e-waste there are PCBs that are present in almost all electronic equipment. Their composition is heterogeneous and varies according to several factors, including: kind of EEE, when and where it was produced, fabrication technology [2], etc. In printers, the PCBs represent about 6.6- 8 wt.% [3].The PCBs treatment may include physical, pyrometallurgical, hydrometallurgical, ectrometallurgical and more recently bio-hydrometallurgical process. Normally there is a combination between these processes [2, 4, 5, 6, 7, 8, 9, 10].The diversity between the different PCBs composition complicates the recycling process since the composition of metal and others materials can vary according to the models. So characterization is an indispensable step before any processing of PCB to begin. Owing to the above said, the main goal of this work has been set to characterize representative samples of PCBs from printers through physical, chemical and microstructural analyses."

Jan 1, 2014

By Y. A. Chang, L. M. Pike, C. R. Kao

"Knowledge of the site preference of ternary solute additions is essential to developing an understanding of how these solutes affect the properties of B2 intermetallic compounds. A quasichemical model will be presented which is able to predict the site preferences of dilute solute additions to tliple defect B2 compounds. The only parameters required are enthalpies of formation at the stoichiometric composition. General equations are developed which can be used to determine site occupations and defect concentrations for dilute as well as non-dilute solute additions. These equations use atom pair bond enthalpies as the parameters. It is found that the site preferences of dilute additions are not always in agreement with predictions based on the solubility lobes in ternary Gibbs isothelms. Predictions for dilute additions to NiAl and FeAl are compared to expel1mental results found in the literature. Satisfactory correlation is found between the model and the experimental results. In addition, the predictions from the model on vacancy concentrations in Fe doped NiAl are compared to recent experimental results by the authors.1.0 IntroductionIntennetallic compounds with the B2 crystal structure such as NiAl and FeAl have been investigated recently for possible use as structural materials in high temperature, oxidizing, and/or corrosive environments. The major limiting property of these materials has been a lack of sufficient room temperature ductility. Attempts to improve the ductility have often been made through ternary or higher order alloying. For B2 compounds, substitutional alloying additions can occupy either of the two sublattices and this site occupancy can be crucial in determining how the alloying addition affects the properties of the alloy. In this manuscript we will discuss the use of thelmodynamic modeling to predict the site occupancies of ternary alloying additions in B2 compounds with the triple defect structure."

Jan 1, 1996

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By W. F. Drinkard

Many in the environmental movement have focused on this element. But, nothing they or anyone does will change the amount of arsenic in the world. This report is on actual commercial plants that we developed and operated to recover or stabilize arsenic values from metallurgical dusts from gold and copper pyro operations and arsenical gold bearing ores. When they were available gold and copper values were recovered. Our experience in arsenic extends over thirty years. My first corporation, Mineral Research & Development Corporation was the first in North America to manufacture the then new CCA (copper-chrome-arsenic) wood preservatives. This class of wood preservatives proved to be so effective that it made wood into an entirely new material of construction. It is not uncommon for wood properly treated with arsenical CCA preservatives to last for thirty; forty, and sixty years. Over a hundred years have been projected in some field tests. Hundreds of thousands of trees have been saved. Millions more trees would have been saved had environmentalists not decided that their arsenic phobia was more important than trees. There are several variations of CCA. The most popular is CCA-C. Its formula is: CrO3 . . . . . . . . . . . . . . . . . . . 47.5% CuO . . . . . . . . . . . . . . . . . . . 18.5% As2O5 . . . . . . . . . . . . . . . . . 34.0% Until recent restrictions were placed on the consumption of arsenical wood preservatives, annual consumption in North America was about 150,000,000 lbs./yr. About 64,500,000 of arsenic as the pentoxide was safely consumed this way. World CCA consumption has been about double the above figures or 300,000,000 lbs. as 100% CCA and 129,000,000 lbs/yr as As2O5. Close to 100% of all the arsenic used in wood preservatives is derived from gold or copper processing. The valence of arsenic required for CCA wood preservatives and many other markets is the same valence that is required for stabilization. The economic challenge is how to get there. We have built and operated eleven plants to oxidize arsenic trioxide to its pentavalent form. Most of these have been classic in that they used a common oxidants such as hydrogen peroxide or nitric acid to achieve this.

Jan 1, 2005

By G. Diáz

The PLACID process applied to the recycling of spent lead-acid batteries is being developed by an European Consortium within the Brite-Euram II programme. The status of the project entitled "Lead Recovery from Lead Oxide Secondaries" is described in this paper. The main laboratory and batch experimental results and the preliminary feasibility study are summarised. The description of the demonstration pilot plant and continuous campaigns programme for 1995 are also included. An interesting global approach is proposed, integrating the Placid process in the existing spent battery recycling pyrometallurgical facilities. This yields important improvements in the overall process. Grids would be easily treated by the conventional pyrometallurgical route, obtaining lead alloys,, while battery pastes, slags and fumes would be fed to the Placid process, obtaining pure electrolytic lead (>99.99 %), ideal for battery paste manufacturing. The implementation of the Placid process into the existing battery recycling pyrometallurgical facilities is analyzed from technical, environmental and economical viewpoints. Greater overall lead recovery, lower operating costs, reduced waste production, environmentally safer residues and much better lead product quality are the key advantages. The authors draw the following final conclusion : Integration of the Placid process with conventional pyrometallurgical treatment is a feasible and very attractive alternative route for spent lead-acid battery recycling.

Jan 1, 1995

By Chunlin Chen

Nickel-sulfide minerals are normally associated with copper and iron sulfides and often contain a minor amount of valuable metals such as cobalt and detrimental impurities such as arsenic. Metal losses in slag vary from process to process during the pyrometallurgical production of nickel and, depend on the feed composition, slag chemistry and operating conditions. Maximiz the metal recovery is one of major considerations to optimize operating condition for nickel smelting/ converting processes. At the same time, the deportment of minor elements between various phases during nickel smelting is of great importance by smelter operators. The Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems [1]. Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature systems. The sulfide smelting module of the MPE, which covers the minor elements such as As, Bi, Sb, Pb, Se, Te, Sn, Co and Zn, is capable of modeling the deportment of major and minor elements between various phases during nickel smelting. In this article the application of the MPE model in modelling the nickel smelting process is presented. The modelling results on the majors and minors are compared with the plant data. The deportment behaviour of arsenic in nickel smelting was analysed and the impact of slag chemistry on slag properties was modelled. These results can assist process metallurgists in exploring the optimum fluxing strategy for smooth operation and the potential practices for improving arsenic removal.