Search Documents

By Krzysztof Kotwica

The steady demand for rock materials leads not only to on increase in mining but to the need for decreasing the loss of material in the process of exploitation as well. It brings about an increase in using of explosives in open pits and as a result an increase of after blasting gases volume, vibrations, the scattering (dispersion) of stone ect. All these factors affecting the environment lead to the research work for applying the electrohydrodynamic methods both in open casts and underground mines. In the article the authors describe the concept of this method and construction of equipment which recently have been successfully introduced in mining, the results obtained determine the possibilities of using this method and the future directions. The results of combined method with high-pressure water jets cutting and prototype equipment for separating rock blocks from the rock mass using special head with high-pressure water jets are also described.

Jan 1, 2006

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By Lawrence M. Gochioco

The interpretation of coal seismic data requires a certain precision and accuracy to make the results more reliable. The signature of the seismic wavelet provides a host of valuable geologic information. Subtle features and anomalies, not easily observed in conventional black and white seismic sections, are enhanced through color attribute displays in terms of frequency, amplitude and phase. Coal seam anomalies like sandstone washouts produce a distinct pattern in frequency and amplitude displays due to the change in the net acoustic impedance contrast. Faults produce frequency and amplitude variations due to interference within the Fresnel zone that straddles the fault. The magnitude of displacement is estimated by studying the effects of faults on reflection amplitudes and frequency from computer-generated models.

Jan 1, 1989

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By Hamid Maleki

A geotechnical monitoring program has been implemented at Energy West Mining Company for enhancing site-specific evaluation of longwall stress conditions. This program consists of underground measurements at five locations in two neighboring mining districts located in the Hiawatha and Blind Canyon Coal Seams under moderate to deep cover. Within the last five years, additional measurements, including data on recorded seismic events and face conditions, have been incorporated into the data collection program together with detailed geologic mapping of longwall gateroads. In conjunction with the measurement program, the authors have completed detailed boundary-element stress analyses of the mine plans. Models have been calibrated using the data from in-mine instrumentations and then routinely used for evaluation of mine plans at depths approaching 2,600-ft. The work has improved our understanding of load transfer, seismicity and yield pillar performance. It has identified areas of potential increased stress levels at certain longwall face positions and provided guidance to measures that could be considered to mitigate the potential for these increased stress levels.

Jan 1, 2009

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By Stephen Tadolini

The annulus thickness, for bolts anchored with resin, effects the systems final performance. Recent developments in the manufacturing process of these support systems, coupled with improved resin characteristics, have resulted in design changes to minimize hole drilling requirements and reduce resin usage. The amount of resin to properly anchor a 7/8-SRD (Special Rolled Dimensions) bolt in a 25.4 mm (1-in) diameter hole has been reduced to about one-third of the resin required to anchor a No. 7 rebar bolt (22 mm (7/8-in) diameter) traditionally installed in a 35 mm (1-3/8-in) diameter borehole. More importantly, laboratory and field tests, indicate that higher bond strengths and anchorage capacities can be realized with reduced annulus systems. These factors have a direct bearing on reinforcement efficiency and subsequent roof support performance.

Jan 1, 1998

By Dennis R. Dolinar

Controlling coal mine roofs subjected to high-horizontal stress conditions has always been difficult and uncertain. Traditional supports such as wooden cribs and posts, concrete donut cribs, and standing supports collapse and fail when the roof and floor move horizontally as mining progresses. The former U.S. Bureau of Mines (USBM) (currently the U.S. Department of Energy (DOE)), in cooperation with Western Fuels-Utah, Incorporated, conducted research to provide an alternative for traditional secondary support systems in a 3-entry gate road system subjected to high horizontal movements. The support system used in several other coal mine operations, consisted of internal high-strength galvanized resin-grouted cable supports. The system virtually eliminates the necessity for external crib, timber, or concrete supports. The support system consisted of 2.4 m (8 ft) full-column resin grouted bolts and 4.8 m (16 ft) long cable supports installed in conjunction with wire mesh and "Monster-Mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. Additionally, cable trusses were installed on the longwall headgate to protect the coal conveyance system from roof and pillar falls created by the formation of cutters and gutters. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper describes the theory of high-horizontal roof movements, the advantages of vertical cable supports and cable trusses, and presents the roof and cable measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1996

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By Gary B. Petersen

The author has developed a seven-step process called the Applied Rock Mechanics (ARM) Protocol that the author has used to solve numerous roof stability problems in mines throughout North America since 1975. It is a practical evaluation process using trained observation, innovative data collection instrumentation, video borehole cameras, analytical processes, and controlled testing methods that have become highly effective in solving ground control problems in every type of underground mine. This paper will describe each of the steps of the protocol and how the rock mechanics engineer applies them to resolve a typical ground control problem.

Jan 1, 2012

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By James J. Scott

Dynamic rock anchors are interior fixtures developed by the author which promise to be a revolutionary development in the field of ground control. The fixtures are designed to be placed in the ground with modern roof bolting equipment, such as the type used in the American coal mining industry. They are composed of a plastic form- able anchor tube which serves to fasten a buttress deformed rod which is thrust and turned into the plastic and in turn clamps the roof plate to the rock surface. Plastic tubes 10 to 16 inches in length provide sufficient anchorage to exceed the yield strength of steel rods 5/8, 3/4 or' 7/8 inches in diameter. This paper presents field testing and early work done on the device over the last seven years. Results of pull tests, creep tests, laboratory testing in concrete, and field testing under natural rock conditions demonstrate the uniqueness and effectiveness of this new support system. A second development which uses the dynamic rock anchor in conjunction with a resin cartridge to provide a stiffer anchorage system is also discussed. These products will be manufactured and marketed by Ingerso-11-Rand Co. under the trademark of DYNA-ROK and DYNA-ROK PLUS anchors.

Jan 1, 1989

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By F. E. Chase

Mobile roof supports are shield-type support units mounted on crawler tracks. Mobile roof support (MRS) units are used during retreat mining, and they eliminate the setting of roadway, turn, and crosscut breaker posts which are required during pillar recovery operations. Mobiles are a more effective ground support than timbers, and their usage enhance the safety of section personnel and reduces material handling injuries. MRS usage is rapidly increasing, and approximately 40 U.S. coal mines have successfully employed this relatively new technology. This paper is in response to increasing requests from operators, State and Federal Regulatory Agencies, and others on the practical aspects of MRS usage in underground coal mines. During this investigation, nearly half of the U.S. mines which have utilized mobiles were visited. This report depicts the more common pillar extraction methods which operators have found successful. The Christmas tree and outside lift methods are illustrated and discussed. Roof control plans that do not require breaker posts or allow pillar extraction with fewer than four mobiles are also examined. In addition, operators' experiences with setting pressures, loads, and rates of loading during pillar extraction are addressed. Mining and support strategies to more effectively control hillseams, weak roof, and gob overrides which have entrapped equipment are also discussed.

Jan 1, 1996