Search Documents

By Y. Pan, P. Tukkaraja, R. BHARGAVA, V.V.S. VYTLA, S.J. SRIDHARAN

Panel caving is an underground bulk mining method that uses gravitational force to mine massive, steeply dipping and deep-seated ore deposits at lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. As caving is a dynamic process, designing an effective ventilation system is challenging; therefore, estimating the airflow resistance offered by the broken rock inside the cave is critical. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using the computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

Nov 1, 2022

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987

By Michael J. Shulman

The DEAREX knowledge acquisition and engineering system is a teaching and exploration tool designed to facilitate the under- standing and development of expert systems by explorationists without the aid of a knowledge engineer and without recourse to expert system languages. To fulfill its objective, the DEAREX system considers the selection of exploration methods in desert areas. The system consists of three parts: 1. A tutorial which introduces the basic and selected advanced concepts of expert systems, 2. A sample program illustrating how an expert system works and can be used, and, most importantly, 3. A knowledge acqusition and engineering program which enables users to develop their own expert systems. The tutorial provides a brief and concise introduction to expert systems, a 10 rule exploration example which defines, explains and illustrates the basic concepts and design of expert systems, and a glossary of expert system terms including cross references. The sample program is a larger, self contained example of an expert system with some commentary illustrating addition- al expert system concepts and the role of the knowledge engineer in particularizing rules and ascertaining the knowledge base. Restricting itself to the selection of exploration methods in desert areas, the knowledge acquisition and engineering program questions the user and converts the answers into an expert system. Questions pertain to geology, infrastructure, availability of instrumentation, personnel, etc. Additional information may also included. In conclusion, some salient points concerning knowledge engineering toolkits, shells and knowledge acquisition capabilities such as contained in DEAREX are discussed.

Jan 1, 1992

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By B. H. Johnston, B. N. Doyle

Introduction In 1983-84 Kidd Creek Mines Ltd. in Timmins, Ontario, started up the second commercial zinc pressure leaching plant based on the Sherritt Gordon Mines Ltd. direct pressure leach process. The first plant using this process was that of Cominco Ltd. at Trail, B.C. (Parker, 1981; Martin and Jankola, 1985). The Kidd Creek plant was constructed to take advantage of the extra capacity that the existing purification, cell house, and casting sections had in comparison to the roasters and acid plant. In addition, pressure leaching offered flexibility in other areas such as treatment of low grade concentrates. The process design package and the detailed design of the autoclave system was carried out by Sherritt. The detailed design for the rest of the plant was done by Cambrian Engineering Ltd. under the direction of Kidd Creek. The construction and commissioning of the plant has been described earlier (Johnston, 1983). This paper describes, briefly, the application of the direct pressure leaching process for zinc concentrates and the integration of the pressure leaching plant into the main zinc plant at Timmins. It discusses some of the startup problems and changes made to the plant. The damage following a fire inside the autoclave is also described. The subsequent repair and recommissioning of the autoclave has enabled Kidd Creek to demonstrate the originally sought advantages of pressure leaching and to take advantage of their extra cell house and casting capacity to produce more zinc. Process principles The development of the direct pressure sulphuric acid leach of zinc sulphide concentrate at temperatures above the melting point of sulphur and at elevated oxygen pressure has been described in detail in a number of papers (Martin and Jankola, 1985; Johnston, 1983; Veltman and Bolton, 1980; Kawulka et al., 1975; Veltman et al., 1977). The most significant aspect of the process is that sulphidic sulphur is converted to elemental sulphur in reactions that can be simply described as follows. ZnS + H2SO4 + 1/2 O2 ZnSO4 + S° + H2O (1) FeS + H2SO4 + 1/2 O2 FeSO4 + S° + H2O (2) The rates of these reactions increase with temperature. However, at temperatures above the melting point of sulphur, 12°C, the presence of a surface active agent is necessary to prevent the occlusion of the sulphide particles by elemental sulphur and the consequent termination of the leach. The zinc that is dissolved according to reaction (1), after purification of the zinc sulphate solution, is recovered by electrowinning. The iron that is put into solution according to reaction (2) is further oxidized to the ferric state and subsequently, as the acidity decreases, precipitates as hematite or as complex basic sulphates. MINERALS AND METALLURGICAL PROCESSING Examples of this are shown below. 2FeSO4 + H2SO4 +1/2O2 - Fe2(SO4)3 + H2O (3) Fe2(SO4)3 + 6H2O - Fe2O3.3H2O + 3H2SO4 (4) 3Fe2(SO4)3 + 14H2O - 2(H3O)Fe3(SO4)2(OH)6 + 5H2SO4 (5) (hydronium jarosite) The conventional zinc process involves concentrate roasting to produce zinc oxide and sulphur dioxide. The zinc oxide is leached in spent electrolyte and the sulphur dioxide is converted to sulphuric acid. The pressure leaching process can, therefore, be used to replace conventional concentrate roasting, sulphuric acid manufacture, and atmospheric leaching with one unit operation. Integration of pressure leaching into the Kidd Creek flowsheet A block flowsheet of the Kidd Creek zinc plant, with the new pressure leach plant integrated, is shown in Fig. 1. The original plant, which was constructed in 1972, is based on standard electrolytic zinc plant technology. Concentrates are dead roasted to remove sulphur. Sulphur dioxide is treated to produce sulphuric acid. Calcine is leached in two stages using cell-house electrolyte. Iron is precipitated as jarosite and solutions are purified to remove copper, cobalt, nickel, and cadmium to provide feed for a partially mechanized cell house. Zinc is plated from solution, and the resulting cathode is melted, cast, and sold (Johnston, 1983). The integration of the pressure leaching plant into the main zinc plant is relatively simple. As shown in Fig. 1, a fraction of the zinc concentrate and spent electrolyte are fed to the pressure leach autoclave, while part of the calcine from the roaster is used as a neutralizing agent in the oxidation step along with. the jarosite leach solution. The main exit stream from the pressure leaching plant is the slurry discharged from the oxidation step, consisting of neutral zinc sulphate solution, unreacted calcine, and precipitated iron oxides. This slurry is transferred to the neutral leach step in the main zinc plant. The leach residue from the pressure leaching step, consisting of basic iron sulphate and elemental sulphur, is washed and impounded along with the jarosite residue produced in the main plant.

Jan 1, 1987

By J. C. Rhodes

The demand for good white minerals for many industries including paint and plastics have made it necessary to import high grade industrial minerals from various parts of the world. Some of the calcium carbonate, barite and talc minerals are from China, Mexico, Jamaica and Haiti. These materials can be processed by custom processors. The custom processor can provide a service to the Industrial Mineral owner. The imported materials can arrive in various feed sizes from lumps (3"-6") down to 325 mesh. The materials can also be in various size shipments or container loads. The economics for importing should be investigated thoroughly. The two factors just mentioned can influence the quantity of material to be processed. These two factors can also influence the total cost for each end product.

Jan 1, 1989

By Ernest L. Bradley

A positive pressure ventilation system, augmented by a dewatering well curtain and underground longhole drilling, provides effective ventilation and radon control at EXXON Minerals Company's Highland Underground Mine in the Southern Powder River Basin of Wyoming. Testing different types of bulkheads, sealants, and bleeder systems has led to improvements in the basic ventilation system. Continued testing of new or different materials and equipment is expected to lead to further improvement in the ventilation program. Effective training of both miners and supervisors is essential to maintaining and improving ventilation techniques. This paper addresses the ongoing ventilation program and experience to date at the Highland Uranium Mine.

Jan 1, 1979

By A. MacG. Robertson

INTRODUCTION The tailings, or solid waste, remaining after uranium has been extracted from an ore and the liquid wastes associated with it contain both radioactive and other substances which, if released to the environment, may have a detrimental impact on man and his environment. Although the radioactivity of the waste is of natural origin, the mining and milling process results in bringing the radioactive ore to the surface, changing its chemical and physical form, increasing its mobility and, therefore, enhancing the potential radiological exposure to man. Exposure to radionuclides released from a tailings impoundment, while small as applied to any one generation, can be made large by counting far into the future, large enough to be the dominant source of exposure from the nuclear fuel cycle, Cunningham (1978). Increasingly it is being found that where the prime concern was initially the radionuclide releases, the release of other pollutants and contaminants may be of equal or greater concern. While there is a definite benefit, at least to present generations, resulting from the recovery of uranium, current and long-term concerns require that consequential present and future releases be kept as low as is reasonably achievable. Design practice, to minimize this release, is currently passing through a technical revolution; precipitated by public and institutional concerns. New techniques and methods are, therefore, being actively sought and continuously implemented. Because of the complexity of the pollutant release mechanisms and the sitespecific nature of each impoundment site and tailings product, a wide variety of site selection and design options have been implemented or considered. It is often possible to design a number of satisfactory tailings disposal schemes which differ widely in nature and cost. This paper outlines the principal areas in which options are available and discusses some of these options. Both operating and post-decommissioning conditions are consi-

Jan 1, 1980

By YU. F. Vasyuchkov, K. Vasioutchkov, B. M. Vorobjev

Introduction It is now believed that, even with the environmental protection measures now being taken, the further application of traditional coal-mining and electric power-generation technologies will inevitably cause further irreversible damage to the global ecosystem. Further improvements in conventional coal-mining technologies, both surface and underground, are expected to have only limited impacts on the economical, ecological and social aspects of coal mining. In countries with a developed coal industry, coal reserves with favorable conditions at shallow depths are rapidly being depleted. Therefore, in the future, more coal will be mined from deeper levels, resulting in higher operational costs and lower labor productivity. The solution to this problem is to be found in developing, promoting and implementing unconventional coal-mining and advanced clean-coal technologies. This paper presents an unconventional concept that has been suggested by the authors. The basic goal is to achieve coal-methane energy resource conservation and to remove barriers to energy efficiency through the adoption of integrated, ecologically clean, innovative technology. The following principles form the foundation of this concept: Energy resource conservation: This principle concerns the exploitation of actual and potential coal-methane reserves in the most effective way with the lowest possible losses and with the application of the most energy-efficient electric power-generation technology. Energy conversion: Energy conversion means the conversion of solid coal to synthetic fuel gas (in situ or in-cycle), the conversion of methane bounded within the coal matrix to free-flowing drained meth¬ane, the conversion of solid coal in situ to a coal/water mixture (slurry), and the conversion of these gas fuels into electric power. Technological and managerial integration: This prin¬ciple means an integration of coal-gas methane min¬ing operations and electric power generation into one commercial mine-to-product enterprise with electric power as the final product. Thus, coalbed methane drainage and coal gasification (both in situ and in-cycle) integrated with a combined cycle of electric power generation constitutes a highly integrated coal-gas methane energy-generation system. The system can be materialized in the form of a local integrated coal-gas electric power complex (LICGEPC). General features of the new concept The coal-gas-methane electricity concept is actually a synthesis of the following four technological components: Coalbed methane drainage. This technique and its utilization attained recognition after commercial operations were proven successful in the San Juan and Black Worriers coalfields in the United States. Worldwide, extensive field experiments and research-and-development activities are being carried out in the area of coalbed methane exploitation and utilization. Recently, coalbed methane drainage for power generation has been undergoing intensive research and development. At the Harworth Colliery in the United Kingdom, a combinedcycle power plant has been built that uses coalbed methane. The plant has an installed capacity of 15 MW Also, Germany, Australia, the CIS and China have conducted various experiments and industrial tests on the use of coalbed methane power generation. Underground coal gasification. Another unconventional technological approach is underground coal gasification (UCG). A number of semi-commercial, demonstration and pilot projects have been undertaken in Russia, the Ukraine, Uzbekistan, the United States, the United Kingdom, Italy and Belgium to demonstrate the technical and economical viability of coal gasification in situ. In Uzbekistan, the Angren coal-gasification station has been in full-scale commercial operation for two decades. The operation supplies a power plant with synthetic coal gas. Under sponsorship of the US Department of Energy's Morgantown Energy Technology Center, large-scale laboratory tests simulating coal gasification in situ were successfully completed by the

Jan 1, 1999

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today's DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine's ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By Allan M. Johnson

Dewatering is a major operational cost at sane mines. Under certain conditions, costs associated with water disposal may continue beyond the productive life of the mine. For mines with mineralized waters, this is of special concern. Since 1974 experience has been gained from the examination of a number of closed underground metal mines that exhibited drainage problems. It was observed in certain cases, that had appropriate steps been taken prior to closure, that the resulting drainage problems could have been largely avoided. The pre-closure steps would have involved alteration to the "plumbing system" of the mines: i.e., the drifts and crosscuts interconnecting the workings of the mine. This could have best been accomplished by the placement of bulkheads and/or selective drifting. In addition to reconfirming that hindsight is 20-20, a lesson learned from these case studies shows that a relatively simple hydrologic evaluation prior to mine closure may avoid a troublesome and costly drainage problem.

Jan 1, 1983

By M. C. Mound, L. Fradette, C. Colbert

Metallurgical Accounting in the mineral processing industry transforms accumulated process data, including flow rates and assays, into a coherent information format. This is used to rapidly provide production reporting and key performance indications. A fully comprehensive and coherency of available data must be a component of any system expected to accomplish reconciliation in the mass balancing process. Quality issues are thus improved with such desired methods via a mass-balancing engine utilizing the results of measurements acquired by various on-line sensors, analyzers, and sophisticated laboratory equipment. Metallurgical Accounting, when accomplished through such an engine, provides high value information in a simple, straightforward, and simplified manner. Exceptional utility is then transparently available to authorized personnel for access to metallurgical accounting reports, production reports, mass balance results, performance indicators, and so on. This paper discusses how such information can be used to "drilldown" into each result set by consulting the data hierarchy to evaluate and validate calculations and input data used to produce the specific results being queried. The power of such a system resides in the full and true integration of all production and laboratory data. What is integrated are the data thus acquired via a single user interface, a single database, a single configuration tool, etc. From this comes the derivation of contextual information and its maintenance. It is possible to reduce metallurgical accounting and production reporting from possibly hours or even days to a matter of minutes. The result is maximization of information reliability and availability from masses of otherwise discrete and difficult to access key data.

Jan 1, 2003

By Mr. Peter J. Huck

Recent research has developed procedural control and geophysical test methods that can greatly enhance quality control in rock grouting. Confidence that design objectives will be made In construction requires that grout monitoring efforts be carefully designed and integrated into the overall project. Parameters that should be monitored are identified and documentation/review procedures that permit effective evaluation of the grouting effort are discussed.

Jan 1, 1980

By . A. J. Erickson

The Park City District, one of three major mining districts in Utah, is located approximately 20 miles southeast of Salt Lake City on the eastern slope of the Wasatch Mountains. The district has been in near continuous production since 1869. Production has been sustained from exceptionally long bedded replacement ore bodies in the Thaynes, Park City, and Humbug formations and also from several major veins. District production is summarized below. TABLE NO. 1 Park City District, Total Production, 1869 thru 1968 (Source r Various Company Records) [ ]

Jan 1, 1970

By John C. Ruckmick

Elemental sulfur deposits generally can be classified as either volcanogenic or biogenic. The latter can be divided into biosyngenetic and bioepigenetic deposits. Essentially all economically important sulfur deposits are bioepigenetic replacements of anhydrite or gypsum in basins containing evaporites and hydrocarbons. Anaerobic bacteria utilize the oxygen of sulfate ions to oxidize hydrocarbons to C02 and reduce the sulfate to H2S. Sulfur deposits are formed by concomitant and subsequent oxidation of the H2S. These bacterial systems can operate on enormous scales, producing deposits containing over 200 million tons of elemental sulfur. There are no known "old" sulfur deposits; almost all known deposits are younger than Miocene and most are still actively forming today. Therefore, it is probable that, with burial and time, sulfur deposits are converted to sulfide deposits. Perhaps more important, bacterial oxidation of hydrocarbons and resultant production and trapping of large quantities of H2S appears to be the logical explanation for the location of many important metal sulfide deposits such as the Mississippi Valley type lead and zinc deposits.

Jan 1, 2013

By Kenneth K. Landes

Lake stone is a term currently applied to chemical and metallurgical grade limestone or dolomite that is brought down Lakes Michigan and Huron by large cargo vessels, mostly self-unloaders. This stone comes from 5 quarries, all in Michigan and all steel company owned. The volume in 1973 was over 34 million tons. The primary reasons for the large volume are the quantity and quality of the stone available, and the low delivery costs to lower lakes markets. The source rocks are Silurian and Devonian limestones and dolomites of exceptional purity. The regional dip of these formations is 50 to 60 feet per mile southerly toward the lowest point in the Michigan structural basin, which is near the center of the Southern Peninsula. Two of the 5 quarries, both high calcium limestone sources, are on Lake Huron in the northeastern part of the Southern Peninsula. The other three are in the Northern Peninsula; one at the northern end of Lake Michigan, and two on northern Lake Huron. The western quarry is in limestone, the other two in dolomite.

Jan 1, 1975

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977