Search Documents

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Gary Tomaino, Specialty Minerals Inc., is the chair of the SME industrial minerals technical committees. Technical committee vice chairs include: •Lucy McCartan, U.S. Geological Survey, agricultural minerals as well as sorbents, filter and process aids. •Steve Herron, Oglebay Norton Performance Minerals, ceramics and refractory materials. •Srinivas Veeramasuneni, U.S. Gypsum, chemical raw materials. •William Langer, U.S. Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2003

By Enrique Hermana, Raymond F. Dalton, Raymond Price, Barry Hoffman

Introduction Chloride leaching of sulfidic ores has been known about for 100 years. It is recognized as a highly efficient process to produce concentrated leach solutions. Despite this, chloride leaching found little practical application until recently because of the highly corrosive nature of concentrated chloride solutions. This situation changed with the advent of modern construction materials such as GRP, polypropylene, butyl rubber, etc. And in the past 20 years, research has burgeoned in the area of chloride hydrometallurgy. The research impetus stemmed from the belief that chloride leaching can provide an alternative to smelters for treating conventional copper concentrates. In addition, chloride leaching was thought to be suitable for on-site refining of copper at small tonnage operations located in remote areas. And chloride leaching was seen as a logical choice for treating unusual or complex concentrates that smelters could not handle. Underpinning these beliefs is the attraction of chloride-based hydrometallurgical processes for sulfidic ores. Sulfur is liberated in the environmentally acceptable elemental form rather than as sulfur dioxide. Consequently, sulfidic copper ores have received much attention. A review of Edmiston in 1984 describes 12 chloride-based processes. All managed to progress past the "laboratory beaker" stage of evaluation. In nine of these processes, copper is recovered electrolytically. Key features of these processes are summarized in Table 1. Table 1 shows that the processes must include a copper solvent-extraction step. Only these processes produce a clean copper electrolyte capable, with no further refining, of directly producing high quality cathode copper. The ICI/Elkem process is the exception here. The rest of these processes use o-hydroxyaryloxime reagents for the solvent extraction of copper and are constrained by the performance of these reagents. This is governed by hydrogen ion concentration (Equation 1). The practical result is that only relatively dilute copper solutions can be treated (Canmet, Phelps Dodge), or careful pH control or adjustment is necessary (Minimet Recherche, B.H.A.S.). This negates one of the attractive features of chloride leaching - its ability to produce very concentrated copper solutions, up to 40-45 gl-1. [ ] In all four processes using o¬hydroxyaryloxime extractants, solvent extraction transfers the copper from the chloride to the sulfate medium. To minimize cross-contamination of the two anions, the loaded organic solvent has to be scrubbed to remove the chloride ion. This represents an additional complication in the solvent extraction circuit. And it

Jan 1, 1988

By Lee W. Abramson, Kenneth P. Akins

The authors have accumulated published data on residual soil and rock tunnels in the United States and have compared it to transit tunneling experience in Atlanta, Georgia, and tunnels in other soil and rock conditions. Two 6.1 meter (20 foot) diameter shield driven, compressed air tunnels were constructed for the Metropolitan Atlanta Rapid Transit Authority (MARTA) connecting the Five Points Station (central hub) with the Peachtree Center Station (first station on the north line). Because of the historic multi-story structures above the tunnels and the variety of subsurface conditions, a comprehensive ground monitoring and observation program was conducted. Conclusions are drawn regarding residual soil and rock ground response due to tunneling. Comparisons are made to ground response due to tunneling in other soil and rock conditions.

Jan 1, 1983

By M. A. Raza

Cable shovels are capital-expensive and primary production equipment in many surface mines. The forces acting on the shovel dipper vary as the dipper moves through the muck-pile. The variations in the forces cause stress loading of the components of shovel and dipper resulting in unplanned downtimes, reduced shovel efficiency, and high mining costs. A potential solution to the above problems is the deployment of an intelligent shovel excavation (ISE) technology, with real-time formation identification, recording, and knowledge transmission capabilities. This research advances the ISE technology by developing dynamic model of cable shovel dipper using Newton-Euler techniques. The model includes the dynamic cutting and dynamic weight forces acting on the dipper as it moves through the muck-pile.

Jan 1, 2011

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By Frank P. Frandina

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. The project involves clearance improvements to twenty-eight tunnels, twenty-one of which require structural modification. With construction of the first Package of tunnels just underway at press time, this paper summarizes the program implementation from design through the initial stages of construction.

Jan 1, 2008

By William R. Yernberg

Most citizens take it for granted, but minerals produced in the mines of the western United States, including Colorado, are crucial to nation’s standard of living and quality of life, said Colorado’s Gov. Bill Owens in his welcoming remarks at the 106th National Western Mining Conference. The conference, which was organized by the Colorado Mining Association (CMA), was held Feb. 4-6, 2004, in Denver. Attendance was425, up substantially from last year’s meeting. The meeting included the CMA annual membership meeting as well as the CMA chairman’s and president’s reports. The meeting also included awards presentations in which companies were recognized for their efforts in pollution prevention, health and safety, and reclamation. The conference also included a tradeshow.

Jan 1, 2004

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By Günter Huber, Bruno Mattle, Helmut Westermayr, Daniel Spöndlin, Max John, Nejad Ayaydin

PROJECT DESCRIPTION Alignment The Strenger Tunnel forms part of the S16 four-lane expressway between Landeckand Bludenz. The construction of this important East-West connection started in 1973with the Arlberg Road Tunnel as its key constituent. Beginning in 1992, solutions for the section between Pians and Flirsch were investigated. Efforts to conserve nature and to avoid potential avalanche and landslide areas led to a solution detouring the villages in the Stanz valley. The starting points were predetermind by the intersections at Pians in the East and at Flirsch in the West. As a result of the expected traffic load and the comparatively high gradient of 2.9%, both one-way, two-lane tubes were constructed at once. The north tube is 5.851 m long, the south tube 5.775 m, see Figure 1. Layout of Tunnel Cross-Section The tunnel cross-section was determined by 2 × 3.75 m wide, 4.70 m high roadways, two sidewalks and sufficient space for two fans above the clearance

Jan 1, 2005

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By D. R. Spears

As part of its mission to develop technology to assure a continuing supply of minerals, the US Bureau of Mines has investigated the flocculation of a Stillwater, MT, chromite ore. The ore was flocculated at different solids contents and at different stirring speeds to determine the importance and effect of hydrodynamic factors. In acidic and basic pH, the chromite ore was flocculated with high molecular weight polyacrylamides differing in the degree of hydrolysis. Polyacrylamides were found to bind to chromite ore particles through hydrogen bonding. The anionicity of the polymer and the pH affected the degree of polymer-particle interaction, which in turn affected polymer conformation at the surface. A polymer conformation with many loops and tails was used to explain high flocculation efficiency. It was found that such a conformation could compensate for poor hydrodynamic conditions.

Jan 1, 1992

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By A. Habibi

A study has been undertaken on two 1.12 m diameter industrial booster fans operating under different blade settings powered by a 1200 rpm motor at the Missouri University of Science and Technology. The fans total pressure varies up to 1kPa forcingup to 25 m3/s through the workings. A pressure-quantity survey has been conducted inby and outby the booster fans with different blade settings. The study uses a variable speed drive (VFD) to determine the effect of rotational frequency on the system. The pressure drop across the bulkheads has been monitored during the experiments. The fans were operated with various blade settings to determine the optimal scenario that maintains the maximum airflow quantity and the lowest power demand at a particular ventilation station. Five scenarios were conducted with different blade setting and mostly with two different speeds. The experimental results show that alteration of fans? speeds by use of a VFD unit can reduce power consumption while maintaining airflow requirements. With the flow rate forced through the mine by the surface fan the blade settings 4 and 5 were determined as possible alternative for the mine ventilation system. In scenario 4, the airflow at the particular ventilation station for a number of speeds is over 20m3/s. The power consumption at 1080 rpm was measured to be 20.1 kW compared to 25.5 kW at 1200 rpm. The operating cost would be significantly less at lower speeds. Scenario 5 is the alternative making use of both booster fans and the main fan in series that meets the minimum airflow requirement at the particular ventilation station along with minimum power consumption. Reducing both booster fans speeds to 1054 rpm results in power consumption of both together dropping to 11.8 kW. Therefore blade setting 5 using two booster fans was determined to be the optimal setting. Separately it was determined that the combination with use of only one booster fan, the West booster fan, running in series with the main fan is the overall optimal scenario. The power consumption of the West booster fan was calculated to be 8.8 kW at 860 rpm with the minimum airflow requirement being met. Computational fluid dynamics is used for analyzing three dimensional flow structures in time domain and calculating the corresponding unsteady pressure fluctuations. The sliding and dynamic mesh techniques were used to study the unsteady flow interaction arising due to the rotation of the fan blades. The numerical predictions of the variables in the form of velocity vectors and contour plots detailing the flow characteristics are then analyzed according to the known physical situation and existing experimental data.

Feb 27, 2013

By F. D. Ayhan

The aim of this study was to investigate the effects of various water mediums on desulfurization and deashing of a coal sample using flotation. For this purpose, experimental studies were conducted on a coal sample containing high ash and sulfur contents. The effects of pH, solid concentration, collector amount and frother amount on the flotation were investigated separately in Mediterranean Sea water, Çermik thermal spring water, snow water and tap water. Flotation results indicated that, when comparing the various water mediums, the following order for the ash content was obtained: snow water < Çermik thermal spring water < tap water < the Mediterranean Sea water. For the reduction of total sulfur, the following order was obtained: snow water > Çermik thermal spring water > Mediterranean Sea water > tap water. When snow water was used as a flotation medium, it was found that a concentrate containing 3.01% total sulfur and 27.64% ash with a total sulfur reduction of 57.06% was obtained from a feed containing 7.01% total sulfur and 41.17% ash.

Jan 1, 2009

Because of complex geological environments, a number of coal reserves occur in inclined or dipping coal seams in certain parts of the world. Longwall top coal caving using split-level a singleentry panel system (SSPS) has been widely used for extracting such coal seams with large thicknesses (greater than 6 m) in China because SSPS can reduce or mitigate problems of coal outbursts, gate road deformations, overturning of shields, downhill sliding of shearer and armored face conveyor (AFC), and so forth, during mining of inclined coal seams. Depth of yield is the range of yield coal from the rib of the pillar to the boundaries where yield ends. It plays a significant role in maintaining the gate pillar stability. This paper presents a study on the stability of an unconventional water-obstruction gate pillar (UWGP) formed by SSPS to prevent water inrush in mining of an inclined thick coal seam in a coal mine in China. As the shape of this pillar is non-cuboidal, nonparallelepiped, a conventional empirical or analytical method is not applicable for studying its stability.

Jan 7, 2020

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

By D. M. Abbott, H. J. Sandri

The geoscience matrix method has proven useful for valuing metallic mineral properties lacking delineated mineral resources or reserves. However, the method explicitly excludes commodity markets from the factors considered; marketability is assumed. When valuing industrial mineral properties, marketability cannot be assumed, it must considered. Market considerations may also significantly affect the standard weightings of geoscience matrix parameters such as the proximity to known deposits. In some cases, such proximity is desirable but in many cases it is undesirable. Application of the geoscience matrix method to industrial mineral properties therefore requires thoughtful, market-related adjustments to the basic geoscience matrix methodology.

Jan 1, 2000

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007