Search Documents

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

By K. N. Han

A kinetic model for the batch leaching of various metals using different lixiviants was developed. The overall material balances for the reactants and products at the solid/ liquid interface were formulated for various types of heterogeneous reactions at the interface. The solutions to these mass balances are identified analytically, as well as numerically. Applications of these numerical solutions to various leaching systems using rotating discs or powders are discussed. The metal-dissolution systems addressed include cobalt, nickel and copper in acid, cyanide and ammoniacal solutions.

Jan 1, 1996

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

By D. Dimitriadis, T. Polglase, M. M. Botz, W. Phillips, R. Jenny

Cyanidation processes for the extraction of gold or silver frequently involve the processing of sulfurcontaining solids that react with cyanide to form thiocyanate. The formation of thiocyanate is an undesired side reaction, and in many cases thiocyanate formation results in a prohibitively high cyanide consumption. With the increasing number of gold and silver mining projects that involve the processing of sulfide ores or concentrates or that utilize a biological sulfur oxidation process, more attention is being focused on minimizing thiocyanate formation and in treating solutions to eliminate toxicity associated with thiocyanate. Though not yet commercially applied, there are several processes available to recover cyanide from thiocyanate to reduce tailings toxicity and to allow the reuse of cyanide otherwise lost to thiocyanate formation. This paper presents an overview of processes available for recovering cyanide from thiocyanate along with estimated operating costs for the processes. Pilot testing data suggests that in some cases cyanide can be recovered from thiocyanate for approximately the same cost as newly purchased cyanide.

Jan 1, 2002

By M. P. Meehan

The purpose of this paper is to present the key elements in a system; study of the electrical system for a timing and/or tilling operation. The ability of an electrical system to function in a reliable fashion at its proper levels is essential for an operation to be successful. A system study consists of a load study for determining the capability of the electrical network to provide power to the various loads and a short circuit study for determining the capability of the electrical protective equipment to properly protect against fault conditions. The sequence of events in a system study is data acquisition, determining the electrical parameters and analyzing the ability of the system to meet these requirements. If the system is small, herd calculations will be the manner in which the study will be conducted; if it is large then commuters will be used. A load study has as its objectives the determination of the capability and reliability of the source of power, transformers and conductors to satisfactorily deliver power to the loads at an acceptable voltage level. The Information required is a single line diagram showing the source, transformers, conductors and loads.

Jan 1, 1980

By Khosrow Bakhtar, Robert E. Cameron, Arfon H. Jones

The use of rock simulators in rock mechanics research greatly expands the scope of the problems that can be investigated with physical models. However, the exact reproduction of full scale conditions, or absolute simulitude, is not obtainable on a small scale model. For this to be possible, the scales of length, time, and pressure (or mass) must be changed without altering the theoretical equations that describe the behavior of materials concerned. In using rock simulants for physical modeling of structures designed in rock, the geometry of full scale structure is reduced to a size suitable for the available testing machine. This will require the strength related properties to be scaled down. Simulation should be representative of the in situ conditions. Complete simulation will require that friction parameters and the stress ratios be matched exactly between prototype and model. The procedure involved in application of physical modeling for rock mechanics research is discussed in the following pages. Background, theoretical approach, and anticipated benefits to the research community are also elaborated.

Jan 1, 1986

By Jacques L. Mauboussin

The EUROPEAN ORGANIZATION for NUCLEAR RESEARCH (CERN) has undertaken the construction of a LARGE ELECTRON POSITRON COLLIDER (LEP), near GENEVA (Switzerland). The facility includes the main 27 km long tunnelled ring, 18 shafts, 20 experimental caverns and many auxiliary galleries. Roughly 800 000 cu.m were excavated in the molasse at 50-140 m depths, using roadheaders for caverns and auxiliary tunnels and 3 WIRTH, 4.5 m diameter, fullface TBMs for the main circular tunnel. Each TBM performs 25-30 m/day. Provisory lining behind them uses either precast concrete elements or shotcrete. Works a e being carried out by a joint-venture of European contractors led by FOUGEROLLE (France).

Jan 1, 1987

By Thomas E. Krakowski

INTRODUCTION This paper presents a method of calculation of internal moments and thrusts in tunnel liners of any material. The method is intended for hand calculation, but as it is numerical in nature it can be programmed for use in computers. The information required for design or analysis is presumed active internal and external pressures, the effective moment of inertia and cross-sectional area of the tunnel liner, the liner's modulus of elasticity, and the coefficient of subgrade reaction of the material surrounding the tunnel. Starting with active external and internal pressures and following the procedure described herein using the structural properties of the liner and surrounding medium, external passive reactions and internal moments and thrusts are calculated. The method is intended for use by design engineers. GENERAL Experience has shown that flexible tunnel liners have less internal bending stresses than those calculated using classical structural theory applied to free-standing arches. In fact, liners which are very flexible in relation to the surrounding soil or rock have virtually no bending moments when compared to free-standing arches supporting equal active loads. In order for this phenomenon to occur, the original active pressure diagram must be "modified" by additional external reactions (passive pressures) from the surrounding material, so that the thrust line within the lining follows the centroid of the tunnel arch more closely than that of a similar free-standing arch. These passive pressures are reactions developed through outward deflection of the tunnel liner. Thus, the outward moving portions of a

Jan 1, 1979

The surface of chalcopyrite was studied in situ in aqueous solution by an atomic force microscopy (AFM). The AFM images showed that some absorbate in patches was detected on the mineral surface, after the chalcopyrite sample was soaked in 5x10-4M potassium ethyl xanthate (KEX) solution at pH 11 for 10 minutes. These patches increased in size with time elapsing. At the same time, as shown by the obtained AFM force curves, the adhesion between the AFM tip and the substrate increased greatly due to the adsorption. Rinsing with ethanol removed the absorbate from the chalcopyrite surface, as well as the big adhesion observed in KEX solution.

Jan 1, 2010

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002

The methods used by Newmont Gold Company for deposit modeling are illustrated by examples taken from current operations and advanced projects. These methods vary depending on a number of factors, including geology, mining and processing methods, economic feasibility, and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques, and being flexible in selecting the appropriate methods.

Jan 1, 1997

By Victor F. Hollister

Skam deposits considered as porphyry copper deposits have been classified into three basic prospecting models: (I) the skam deposit associated with a mineralized intrusive (Pima-Mission), (2) the deposit associated with a barren igneous stock (Ertsberg), and (3) mineralized rock that seems to have no clear association with apluton (Phoenix). Pima-Mission, Christmas, and many other copper-bearing skarns developed in carbonate sequences near mineralized intrusives form an important part of the deposit. Historically, copper derived from the mineralized intrusion accounts for less than half of the metal produced by most porphyry mines, as most mineralization occurs in the intruded rocks. Skam mineralization is an important part of wall-rock metal deposition, because carbonate sequences are preferentially replaced by sulfide and skarn minerals. Exploration for skam mineralization is an important phase of porphyry copper exploration. Impure carbonate beds can become better host rocks for skam deposits than pure carbonates, and these in particular should be included in porphyry-exploration programs if the impure strata are cut by the stock. Skam deposits can also form near stocks that are barren of sulfide. In this model, the two best ore guides are strata favorable for mineralization (usually impure carbonate beds) and the intrusive contact. Faults can also act as important ore controls. Some skarn deposits form that have no clear genetic connection with a stock, although intrusive rocks are known in the district. In such cases, the best ore guides are strata and district-wide faulting. Dikes and sills are also common and mineralization can locally prefer their contacts even though the igneous rocks are barren. Skam minerals are influenced by the chemical composition of the carbonate. Forsterite, brucite, tremolite, and talc are common in skams developed in dolomitic beds. Skams derived from calcic beds often contain wollastonite, calcite, stilbite, or idocrase. Diopside, however, is a common accompaniment of copper sulfide in skam regardless of the original composition of the carbonates. Tremolite and possibly other amphiboles and chlorite can occur significantly in the zinc-lead portion of skams. Gamets occur in magnetite, copper, and zinc-lead zones of skams, but are not as diagnostic as diopside for the copper zone or tremolite for the zinc-lead zone. A general desciption of skam-deposit mineralogy can be used to construct prospecting models of porphyry copper skams. An abstract of such a description follows.

Jan 1, 1991

By Keith J. Henley, Nicholas C. Clarke, Paul Sauter

A detailed investigation of the stability in cyanide solutions of native gold and gold-silver tellurides in a flotation concentrate from the Golden Mile, Kalgoorlie, has been undertaken to assess whether leaching under different conditions can be used to quantify the distribution of Au between native gold and gold-silver tellurides, as suggested by, for example, Chryssoulis and Cabri (1990). The leaching was carried out on +20 µm native gold and gold-silver tellurides separated from a high-grade flotation concentrate and then diluted with barren quartz. The material leached assayed 270 ppm Au and 118 ppm Te and the leach conditions used were:- Stage 1: Leaching in dilute cyanide (0 .1 % ) at pH 9 .5 for 24 hours to dissolve native gold but not gold-silver tel­lurides. Stage 2: Leaching the residue from Stage 1 in strong cyanide (2%) and pH 12.5 for 96 hours to dissolve gold-silver tellurides.

Jan 1, 1995

By E. F. Divers

Adequate ventilation of coal mine working faces is the most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. US Bureau of Mines research has shown that to control respirable dust, you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane, the most effective approach has been to use a blowing brattice, or tubing, and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present. Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan- powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray- fan controls methane on exhaust-ventilated sections.

Jan 1, 1987

By John C. Edwards, Robert C. Bates

Modeling uranium mine radiation control methods and natural environmental radon variations is an extremely complex endeavor. A number of authors have examined particular facets of the problem and have proposed models for their area of interest. Bureau of Mines personnel brought together many of these individual studies, and from them have attempted to develop a coordinated plan for modeling radon daughter concentrations in the uranium mine environment. This approach is described.

Jan 1, 1981

By Brian Hester

Many Third World African countries are well-endowed with minerals - especially gold and diamonds - while only a few have important base metal deposits. For decades since colonial rule, political and economic conditions discouraged interest by Western capital. Influence from Soviet Bloc countries, however, has declined with the move toward multi-party rule. And the left wing orientation, once widely favored by Third World African countries, has almost disappeared. With International Monetary Fund (IMF) encouragement, these Third World African countries now encourage representational government and solicit western finance to expand their industries. Mining is especially encouraged. The North American mining industry is following the same trail as other capital intensive industries and looking abroad for opportunities. The Prospectors and Developers Association of Canada released figures that show exploration expenditures in that country were halved between 1987 and 1990. Figures for the United States are not so easily found but every indication points to a downward trend. While total annual expenditures on US exploration by corporations as a group are either declining or remaining constant, expenditures away from North America is increasing. Gold exploration expenditures in 1991 by the major companies tracked by Minerals Economics Group were less in the United States than for Latin America and the Southwest Pacific combined. The same study showed as much was spent in the Republic of South Africa and "Other" areas combined as in the United States. Expenditures by major corporations in these "Other" areas amount to only 5.2% of their total budget. Third World Africa is a major component of these "Other" areas.

Jan 1, 1993

By William Mayrsohn

INTRODUCTION The net smelter return (NSR) calculations made on various smelter-refiner alternatives, is usually done by taking the gross metal value less metal deductions, smelter-refiner charges and transportation-insurance costs. An important further step in the calculations is the financial charges imputed by refining time, transportation delays, to the time gold is returned (if tolled) or paid for if bought by the refiner. Metal that is priced in advance of payment also requires a forward premium that the mine may or may not be getting. This is a hidden cost that is often omitted from the calculations. Segmentation of each of the above costs are vital to see where improvements can be made through negotiations, better choice of metal pricing or transportation alternatives. BASIC NSR CALCULATIONS SMELTER-REFINER CHARGES Payable Metals - Treatment Refining Charges: Since these can vary from one smelter to another, the effect of a $25 per ounce price increase/decrease should be calculated and kept in mind. This effect is compared to differences in refining/treatment charge and a total smelter/refiner cost on a cost per ounce of dore, gold, or a dry ton of concentrate. Transportation - Insurance: Research has to be done on transportation alternatives perhaps with some assistance from the smelters, railroads or trucking companies. For dore, the U.S. postal service is viable and inexpensive. For railroads, deal with the regional office ie., B&N El Paso, if production warrants regular bulk shipments. Spot rates tend to be higher. A small mine producing concentrates usually goes to the nearest smelter due to extremely high transportation costs. Here is where a refiner can help. Insurance-Quotes for rates on dore/ concentrates are easily obtainable, but the mine has to shop for the best rates. Your insurance broker is the best source of this information. Differences between Mine and Smelter/Refiners Metal losses can be caused by the following: - Concentrate dry weight differences caused by moisture determination or faulty scales (often at the mine). - Sample bias by poor preparation practices on either side ie., grinding of the sample removing gold; or a poorly mixed concentrate. Dore bullion has no such difficulties.

Jan 1, 1987

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth's surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth's surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET's uranium exploration procedures.

Jan 1, 1981

By Ken Criley, Marc E. Orman

Identifying the optimum ultimate height for heap leaching ore requires the consideration of a number of competing factors. A primary limitation is the reduction in the permeability of the ore with increasing heap heights. At low permeabilities the heap can blind off, cause serious ponding and runoff, and become very difficult to rinse at closure. The authors present a laboratory methodology that has been successfully used on several projects to identify the maximum height for controlling heap permeability.

Jan 1, 1996

By Shuyu Qin, Shujiang Sun, Jingfu Zhao

The three key parameters of mine fires are local airflow velocity, temperature and oxygen concentration. According to the theories of seepage in porous media, heat transfer and heat dispersion, mathematical models were constructed based on the three parameters. The models can be used for early prediction of mine fires and for estimation of the level of spontaneous combustion. Proper use of the models can assist in preventing and controlling mine fires. KEY WORDS: airflow velocity, temperature, oxygen concentration, numerical modelling, mine fire prediction.

Jan 1, 1993