Search Documents

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By Joseph D. Martinez

Salt, because of its plasticity, exerts a major influence in deformation. Resulting salt structures are common world-wide. A special type, salt domes, are associated with thick sequences of sediments deposited over salt. Their upward intrusion is generally thought to be in response to buoyancy. Mines in salt domes reveal an internal pattern compatible with large amounts of vertical flowage. Caprock, the end product of accumulation of anhydrite from salt dissolution, attests to long continued upward growth and concomitant truncation by moving underground waters. Concepts of modes of growth are evaluated and related to problems in utilization.

Jan 1, 1979

By M. R. Paterson, M. K. Suddaby

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a continuous elution process is established and the development of a large-scale pilot plant is described. It is based on a continuous elution apparatus that has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra, and other methods of elution. The performance of the atmospheric continuous elution system (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1988

By M. E. Smith

Chile is the world's largest copper producer and as such sets the standard of practice in copper SX/EW design. The authors summarize the liner systems used at many of Chile's major copper producers both operating and planned. The evolution in the state of the art is also discussed, considering both economic factors and Chile's burgeoning environmentalism.

Jan 1, 1994

By D. E. Ranta, M. W. Springett

During the 1970's geostatisticians were often accused of not paying sufficient attention to geologic features in the computerized generation of ore reserves. Unfortunately this charge was all-too-often justified and the results of such studies tended to be oversimplified and failed to reveal the full potential of computerized reserve estimation and geostatistical methods. There were some notable exceptions to this trend. Techniques were described that paid a great deal of respect to the geologic characteristics peculiar to certain deposits (Rendu J-M, 1984; Barnes T. E., 1982). At Gold Fields several techniques have been developed for handling the geologic characteristics of orebodies for reserve estimation purposes. These have developed over time and the evolution of their adoption has been a reflection of our own learning experience from the practical application of computerised reserve estimation on many precious metals deposits.

Jan 1, 1992

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By D. A. Bird

Water chemistry data were used to identify the sources of ground-water and surface-water inflow to the IOZ block cave mine. Water samples were collected to obtain vertical and lateral hydrochemical profiles within different levels of the underground workings. Water chemistry data were evaluated in conjunction with geologic and structural information to define controls on locations of ground-water inflows, and to select targets for drilling and interception of water. Drilling has intercepted water-producing zones that were previously unidentified through mapping and drilling. The program has resulted in a reduction in water inflows to the block cave area.

Jan 1, 1998

By G. D. Trump, F. L. Stanley

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce the cut point and improve separation efficiency. Preliminary economic analysis show that the new circuit provides an attractive payback on capital investment.

Jan 1, 1999

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By Boleslaw Tolwinski

This paper presents an algorithm for the de- termination of a production schedule for an open pit mine that satisfies all principal physical and economic constraints required by a realistic mine design. We propose to model the evolution of the mine over time as a sequential optimization problem or, equivalently, as a problem of finding a path with a largest value in a graph. Some preliminary evidence is provided that such a path can be effectively sought by an algorithm that combines a number of heuristic search rules, inspired in part by learning theories developed in Artificial Intelligence.

Jan 1, 1992

By J. Cooper, M. W. Staub

Environmental management systems (EMSs) have been in use for more than a decade. US mining companies are only just beginning to adopt EMSs. This lag is primarily due to lack of market forces and lack of evidence that EMSs add value over standard compliance programs. Several recent studies concluded EMSs improve environmental performance and reduce costs. State and federal regulatory agencies are using EMSs as an innovative tool to streamline the regulatory process and achieve continual environmental improvements. The climate is right for the mining industry to adopt an EMS model that improves environmental performance and takes advantage of new regulatory programs.

Jan 1, 2004

By M. Saunders Macdonald

A number of open pit gold mines in Nevada extract ore from areas below natural groundwater elevations, necessitating dewatering and some method of disposal of the extracted water. These open pits extend well below the water table, with associated dewatering volumes greater than 10,000 gpm. Some mines, with large volumes of dewatering water to manage, have constructed re-infiltration basins to re-introduce dewatering water to the groundwater system some distance from the pits. This paper presents an overview of the state of the art of re-infiltration projects, including the permit process for such projects in Nevada, and the necessary engineering considerations.

Jan 1, 1996

By M. W. Brandt

In the November 1957 issue of "Chemical Process Engineering," a British publications, there appeared an article entitled "Correct Selection of Drying Equipment." The author wrote as follows "Whether batch drying or continuous drying' methods are applied, the basis of efficient drying is heat distribution, control of rate of heat input, and heat transference from heating medium to the particles of the material to be dried." The author continues: "Because the efficiency of direct dryers, such as hot air or hot gas dryers, increases with rising inlet temperature of the drying air or gas when exhaust temperature remains fixed, the highest practical drying temperature should be used. Exhaust air should leave the dryer at the lowest possible temperature, but as fully saturated with moisture as possible." It is certainly conceivable that the author of this article by outlining the basic requirements for efficient drying methods has unwittingly given the reasons why fluidized drying is rapidly being adopted for so many industrail applications, including the dryingof fine coal. An examination in greater detail of the individual basic requirements for efficient drying as outlined by the author is perhaps the most logical starting point.

Jan 1, 1958

By Gene M. Handel

Today the world is heavily dependent on petroleum for its energy. In the United States, over 75% of the primary energy used comes from petroleum. Other developed countries are similar. The less developed countries have a lower dependence on petroleum just as the United States did through the early 20th Century. However, these less-developed countries look upon petroleum as one of the primary energy sources for the economic growth required to improve their standard of living. So everyone considers petroleum an essential ingredient in the recipe for the good life. But there is a substantial problem with this recipe, and it is finally getting general recognition. Petroleum is a finite resource, and the world is using it up at a rapid, accelerating rate. Though it won't be exhausted for many decades, the early warnings of ultimate limits have already appeared. The suppliers of the incremental production in the Middle East have threatened to restrict increases in their production rates. And, of course, the short term embargo of four years ago clearly demonstrated the economic impact of reduced access to petroleum as a primary source of energy. World petroleum production will probably peak in. 10 to 15 years and then start declining. When that happens, economics--the allocation of scarce products (also known as the dismal science for obvious reasons)--indicates that the price of petroleum will escalate in real terms. So that's the situation today. We have a serious and growing problem facing us that could substantially alter the quality of our life over the next 25 years. Recognition that the society may face a period of lowered expectations after a long period of upward mobility will be a painful experience, but it is certainly not the moral equivalent of war. And, besides, we have time to take positive actions to avert the most serious consequences. When we consider alternate energy sources, the possibilities are almost endless: coal, oil shale, tar sands, solar, fission, fusion, wind, tides, biomass, etc. Actually, the list is endless because new possibilities are continually being proposed. Of these possibilities, coal uniquely stands out as an attractive substitute for petroleum. Coal can be, and is, burned to generate electricity and provide heat. It can be liquefied to supplement the liquid fuels from petroleum, and it can be gasified for use as synthetic natural gas. Unlike exotic alternate energy such as solar and fusion, coal has successfully been used commercially to produce synthetic fuels. But, the technology does need to be refined and modernized. Thus, coal's role is not to be "America's Ace in the Hole," but to bridge the transition from primary dependence on petroleum for energy to the utopia of renewable sources of energy. But don't be mislead by the prophets--those renewable sources of energy are going to be very, very expensive when they are invented.

Jan 1, 1978

By J. H. White

It is hypothesized that the Hotelling valuation principle (HVP) can determine the value of developed gold reserves using simple methods and easily obtainable data. This paper reports the results of an empirical test of this hypothesis. The model for the HVP is given by [V R=Cp-0(1) or V - CP-0' R(2)] where p = current spot price of gold per oz, [c] = average extraction cost of gold per oz, V = current market value of the gold in the ground (dollars) and R = gold reserves (oz). Using publicly available data from North American gold companies, we obtained data for V, R, p and c, and we ran a simple linear regression using Eq. (1) as the definition of the dependent and explanatory variables. By examining the value of the coefficients of the resulting regression equation, we can draw conclusions as to whether or not the HVP can be confidently used as an estimator of the value of developed gold reserves.

Jan 1, 1997

By Sarkis G. Ampian

This late 1979 Bureau of Mines report presents current stocks and monthly consumption rates for Guyanese refractory bauxite (GRB), with emphasis on the impact of the GRB shortage on the refractory and downstream industries, general background material, and an evaluation of the situation resulting from the strike of Guyanese bauxite workers during the summer of 1979. A study by the Bureau indicated that industry stocks contained little more than a month's supply of GRB--30,000 calcined short tons (CST), at present consumption rates of 25,000 CST per month. The report was requested by the Federal Emergency Management Agency (FW) in response to refractory industry requests that the Government release GRB from the National Stockpile to minimize forecasted industry problems. The report traces the historical innovations in the high-alumina and/or bauxite-type refractory products industry, eventually leading up to fabrication of modern, high-quality firebrick and monolithic refractories.

Jan 1, 1980

By Carl R. Christiansen

Underground sites have great potential for industrial plants, for warehouses, and for other purposes where above-surface locations are now employed. Subsurface locations have generally been over- looked by industrial planners even though they may offer many features of superiority over the conventional sites. There are many opportunities for industries or warehouses to go underground. New space can be excavated expressly for this purpose or openings in existing mines may be converted to useful space. Another possibility is the pre-planned mine-industrial site, in which a mineral product is mined and marketed as a commercial venture while utilizing a mining plan which will permit rapid conversion of the openings created into active industrial areas while mining continues in the adjacent ground. An underground plant located in chambers created by excavating space in solid rock has many advantages, including low construction costs, low heating-cooling costs, freedom from storm damage or other surface weather conditions, absence of traffic noise and vibration, fireproof construction, low insurance costs, excellent working conditions, easily controlled temperature and humidity, almost unlimited bearing capacity of floors, low maintenance costs, no effect upon surface.

Jan 1, 1973

By E. Topuz

Mining equipment, like all other equipment, is subject to failure. Since most failures occur at random and are unexpected, corrective maintenance is usually more expensive and causes more down-time than preventive maintenance. In order to reduce the number of failures and thereby increase the availability of an equipment or system, preventive maintenance can be scheduled at predetermined points of time. The preventive maintenance scheduling policies presented in this paper utilize reliability and probability theories. They can be applied to various production bottlenecks where high cost equipment precludes having sufficient quantities of stand-by units.

Jan 1, 1982

By E. G. Noble

Microbial leaching is being investigated as a method for recovering the metal values from a domestic low-grade manganese wad ore. Early work showed that heterotrophic microorganisms present in the ore solubilized manganese when cultured in a glucose-mineral salts medium. More recent shake-flask tests using molasses as the sole nutrient source extracted 97 pct of the manganese from minus 300- µm ore in 4 weeks. Column bioleaching with the molasses medium solubilized 99 pct of the manganese from minus 6.3-mm ore in 50 weeks. The results of flask, column, and lab-scale heap bioleaching studies are presented.

Jan 1, 1991

By Jack M. Jodrey, Neil D. O’Donnell, R. A. Metz

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1992