Search Documents

By Meredith Scaggs, Emily Sarver, Lucas Rojas Mendoza

"Early on Jan. 9, 2014, approximately 37,800 L (10,000 gal) of crude 4-methylcyclohexanemethanol (MCHM) leaked from a storage tank sitting on the bank of the Elk River near Charleston, WV (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal and is considered nonhazardous in terms of transportation, storage regulations and also toxicity (CDC, 2014a). Freedom Industries Inc., a producer and vendor of specialty chemical products, had acquired the storage facility from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein and McWhirter, 2014).The spill site was located a little more than 1.6 km (1 mile) upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a "Do Not Use" order was issued for all customers (WVAW, 2014a).With little information readily available regarding the potential human health effects of MCHM, the U.S. Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the "Do Not Use" order remained in effect for a total of eight days, until Jan. 17, when the WVAW distribution water was confirmed to have MCHM concentrations below the approved level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at sub-ppb concentrations, a fact that undoubtedly added to growing public concern (Rosen et al., 2014; Gallagher et al., 2014). In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until Feb. 25 when MCHM levels were measured below 2 ppb (WVAW, 2014b), and eventually replaced the affected filter media (WVAW, 2014c)."

Jan 1, 2014

By Warren G. Burres

or more than 50 years the Portland Cement Association has represented the United States cement industry in matters relating to the technology and use of cement and concrete. Interestingly enough, PCA?s emphasis has been on concrete and its uses rather than on Portland cement. The cement industry realized long ago that cement is basic and serves its fundamental purpose as an ingredient in concrete. Cement could never be successful if concrete were not. Work with the users and specifiers of concrete had to be done at its end point of application--in a building, bridge, dam, highway or home. PCA, over its half century of existence, has been dedicated to this job. I should like to talk to you today on the less technical side of concrete--what it has been--what it is today--and what it can offer in future construction. Concrete, in many forms, has a long background extending from such notable historic times as the Roman Empire. Here, concrete made from pozzolanic cement from the slopes of Mt. Vesuvius was used to construct the Coliseum, home of the Roman circus; for the Appian Way, the ancient forerunner of the Interstate system; and the miles of aqueducts throughout Europe, many of which still carry water. In 1811 Joseph Asppin, an English bricklayer, made the first modern cement by the artificial mixing of pulverized limestone and clay materials. Ht,

Jan 1, 1971

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. It remains a challenging area of contemporary research in mineral processing.

By Earl R. White

In 1950 Kaiser Steel Corporation acquired control of the Utah Fuel Company, a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah. The mines at Sunnyside have been producing high quality coking coal since the late 1890's. Kaiser Steel acquired the coal deposits at Sunnyside in order to supply the necessary coke for its steel plant at Fontana, California. The Sunnyside coal deposits are made up of two mineable beds, the upper and lower Sunnyside seams. Both seams outcrop along the southward facing escarpment of the Book Cliffs. The coal seams dip under the massive sandstones of the Book Cliffs to the northeast at 5 to 22 pct., with the steepest-part being near the outcrop. Mining at Sunnyside up to 1961 had been carried on with room and pillar methods. The deep cover and rotten roof conditions, along with the need of increased tonnage, required a change of mining technique. Numerous ideas were presented, discussed, and economically analyzed. Several people involved in these discussions, with the aid of W.W. II, had been introduced to the European methods of coal mining, namely the longwall technique. The European mines had long been plagued with near similar conditions as those at Sunnyside, particularly the deep cover problem. The longwall method seemed to be working very well under these conditions, and with the extensive studies given longwalling by the Kaiser Steel mining officials, it was decided to give longwalling a try.

Jan 1, 1976

By W. H. Langer

Around the beginning of the 20th Century, annual aggregate production in the United States amounted to about 50 million short tons. Today annual aggregate production is nearly 2.5 billion tons. Over a third of the States in the country produce more aggregate than the Nation did at the turn of the century. I would like to describe some of the historical events that allowed this nearly 50 fold increase in aggregate production. You might wonder why I want to talk about history. Some of our best ideas lie buried in the past, waiting to be rediscovered in the present. Almost every issue that the aggregate industry experiences today has been recognized for at least a decade; many of those issues have been recognized for a half a century; and a few of them have been recognized for nearly a century. The main reason for this article is to save the past from the forgetful indifference of the present-to faithfully preserve the past, to illustrate the insights of our predecessors, and to demonstrate how little of what we know today is really new.

Jan 1, 1998

By Y. J. Wang

Optimal sizing of a ventilation shaft is a classical subject in mine ventilation economics.. The shaft size is optimized by minimizing the sum of shaft-construction and ventilation-power costs, or owning and operating costs. The length and air quantity of the shaft are held constant, and the location of the shaft, affecting its depth, and construction and ventilation power costs, is not considered (Hartman, 1961; Lambrechts, 1974; Wang et al., 1978). This paper proposes an approach by which the location and size for a new pair of shafts (intake and return shafts) are optimized for a coal-mine ventilation network. Specifically, the problem is to determine the location and size for a new pair of shafts, and the distribution of air between the new and old shafts so that the combined cost of shaft construction and ventilation power is minimized. The shaft length or depth corresponds to the height of overburden at any shaft location. To simplify the problem, the shaft locations will be limited to the line along the main or submain entries, and the connection entries at the shaft bottom neglected. In order to calculate the ventilation-power cost, the air power of the system should be determined. This in turn requires the calculations of the air quantity and pressure of each fan in the network, satisfying Kirchhoff's laws and Atkinson equation. After obtaining the air power, the cost calculation is straightforward. In the following, we shall assume that the resistances of all airways, and the quantity for each mining section, which is controlled by adjusting the air regulator, are all known. The resistances for the shafts are determined from the estimated friction factors, and shaft dimensions and lengths. Furthermore, it will be assumed that the fans can be selected to meet the duties called for by any network solutions.

Jan 1, 1982

By Peter H. Grimley

It is important to realize that lending institutions have a very different risk-profile from that of an equity investor. For bank financing, a feasibility study must address the concerns of the lender and these can be summarized under the four 'PI Is: Project, Performance, Product and People. Generally, feasibility studies focus on the measurable project risks associated with a new venture, but frequently insufficient emphasis is placed on key risk areas such as ore grade and metallurgical recovery. Before accepting full or even partial non-recourse risk, financial institutions will demand evidence that the project was constructed according to specifications and within budget and that its Performance within agreed limits has been demonstrated. Product risk should be discussed in detail in any feasibility study. For industrial minerals, penetration of the market can be critical to success and for commodities with volatile prices, the sensitivity of the cash flow to a range of prices should be carried out. Methods of reducing price risk such as long term contracts or, in the case of gold, forward selling should be carefully evaluated. The People risk is rarely discussed in feasibility studies, but can be a key element. Few projects turn out to be faithful copies of the study and the ability of the operator to identify

Jan 1, 1988

By L. Yuan, J. Soles, W. Tang, R. Thomas

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12V, 24V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Feb 1, 2023

By E. G. Cauda

Diesel engines are a major source of underground miners? exposure to nitrogen dioxide. In an effort to reduce the exposure of underground miners to regulated and unregulated diesel emissions, primarily particulate matter, mining companies in the U.S. are retrofitting existing and introducing new engines with various exhaust aftertreatment technologies. Different aftertreatment devices, or changing the operating temperature of a selected device, can have unexpected effects on the concentration of nitrogen dioxide emitted by a diesel-powered piece of equipment. This paper provides an overview of the effects different exhaust aftertreatment technologies available to the mining industry have on no2 emissions.

Jan 1, 2010

By M. B. Haggerty, Joe Welna

The Minnesota Department of Transportation is constructing a stormwater storage facility (SSF) along Interstate 35W (I35W) south of downtown Minneapolis, MN. The project will provide storm surge capacity reducing the frequency with which major precipitation events result in flooding of I35W. The design consists of six, 42-foot diameter, 90-foot deep, adjacent underground shafts providing 14.7-acre feet of storage. Construction challenges include high groundwater with variable glacial outwash deposits. Constructability and ground variability were managed using construction manager general contractor (CMGC) project delivery. CMGC provides an environment for collaboration and innovation starting in the design phase and carrying through construction. This paper provides an overview of key efficiencies and collaboration examples implemented on the I35WSSF project which were aided by CMGC delivery.

Jun 13, 2023

By Donald P. Richards, David W. Campo, Michel Coudry

This paper presents a review of the grouting works of Line 2 of the Greater Cairo MetroSystem. The Nile River alluvial deposits underlying this ancient city provided for a challenging and sometimes difficult grouting project. Permeation grouting using state-of-the-art computerized grouting techniques, as well as extensive ground treatment by jet grout, was per-formed for soil consolidation and/or groundwater control. During the project, over 425,000m3 of ground was treated, requiring 1.4 million linear meters of drilling and PVC injection pipe, 54,000 m3 of bentonite cement and 230,000 m3 of chemical and mineral grout. In addition, over 70,000 m3 of ground was treated using the jet grout method. Relative to major international transportation projects, the grouting works for Line 2 of the Cairo Metro represent one of the largest worldwide grouting endeavors to date.

Jan 1, 1997

By Jon Y. Kaneshiro, John S. Griffith, Anthony F. Stirbys, Mauricio Andrade

This paper presents an overview of the New Mississippi Tunnel Outfall for the Transportation Expansion Project (T-REX). The Outfall conveys highway and other urban drainage to the South Platte River as well as provides long needed relief from flooding problems in the southeastern portion of the Interstate 25 highway corridor. The Outfall tunnel incorporates a one-pass precast concrete segmented liner to convey storm water under I-25 then under Mississippi Avenue to the river. The Outfall crosses both the existing I-25 as well as the future improvements including under the Light Rail Transit, a new bridge abutment, widened lanes, and new retaining walls. The Outfall also crosses adjacent to several buildings and five bridges, under major traffic and utility intersections, and through difficult geology.

Jan 1, 2003

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By P. B. Queneau, J. E. Litz, T. P. McNulty

I. INTRODUCTION Modern hydrometallurgy has its roots in such notable successes as heap leaching for recovery of copper, cyanidation of gold ores, the Bayer process, the Oxland process for tungsten, electrorefining of copper, roast/ leach/electrowin process for zinc, and production of yellowcake from lowgrade uranium ores. Metallurgical testing techniques, sampling and analytical procedures, operating and maintenance practices, and improved methods and materials of construction which were pioneered in these processes have promoted the extension of hydrometallurgy into other applications. Periodically, new tools such as solvent extraction, resin ion exchange, and flocculants have opened new avenues to hydrometallurgists. Conversely, pursuit of more complex mineralization, the rising costs of energy and environmental quality preservation, and declining ore grades continue to create new challenges. For much of this century, it can be fairly said that practically any hydrometallurgical development moved the frontier of technology. The 1970's and 1980fs, however, have seen a significant maturing of hydrometallurgy's role in process metallurgy. Simplistically, this maturing seems to derive from a growing awareness of the strengths and weaknesses of hydrometallurgy and a determined effort to capitalize on the strengths. For example, many of us were among those revolutionaries of the 1960's and 1970's who taught that "chemical smelting" was the answer to the treatment of all sulfides. We now recognize, however, that only in very special cases can hydrometallurgy offer economic advantage over the generally less energy-intensive pyrometallurgical systems. The maturing of hydrometallurgy does not, however, signal stagnation. Important innovations are being studied and developed in most extractive areas, and a number are approaching or have achieved commercialization. From our company's perspective, that of an organization dealing with the development of the most economic solutions to metallurgical problems, innovation must be defined as the commercially successful reduction of an idea to practice. There appears to be no shortage of ideas, nor has there ever been a shortage. Many ideas now being implemented were conceived decades ago, but reduction to practice was foiled by the lack of such technology as responsive process control and economical materials of construction capable of withstanding highly corrosive or erosive environments. Commercialization of a new process is a particularly challenging undertaking. Even if technical risks are reduced to a minimum through careful and thoughtful process development, there are inevitable uncertainties in feed characteristics, variable costs, and product prices. Commercialization takes courage, both on the part of innovators who may be staking their careers or reputations and of investors who may face financial disaster in the event of project failure. This paper discusses innovative programs and recently commercialized processes which either have been discussed in the literature or disclosed to Hazen Research staff in private nonconfidential conversations with contacts in industry. Regarding this latter category of information, relative ease of communication has resulted in many of our observations being of North American origin.

Jan 1, 1985

By Grover H. Emrich

Pennsylvania,, due to its location in the humid east, is fortunate to possess within its borders large quantities of water. Most of the State is drained by three major river systems-the Ohio, Susquehanna and Delaware. This abundant supply of surface water has been widely utilized throughout the State, but today other sources of water must be developed due to the increasing demands for water, die largest undeveloped source of water in Pennsylvania is ground water. Pennsylvania is also fortunate to possess extensive coal resources. These coal resources have contributed measurably to the development and prosperity of the States Coal and water's - two valuable resources - have been necessary for the development and industrialization of Pennsylvania, The State needs both resources but can no longer afford to develop one while adversely affecting or destroying the other, We are aware of the effect of coal mining on surface water, but coal mining can also materially affect subsurface water, This effect will according' to the local geologic conditions.

Jan 1, 1965

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

In a world dependent in part on the consumption of depletable natural resources, development of new areas of mineralization is a necessity for replacing those reserves. Exploration, which is the initial task of replacement, is an information-gathering process which supplies input for management decisions on mine development. If the demand for resources is the driving force of exploration, then the scientific basis for its pursuance is the hypothesis of anomalous mineralization in a metallogenic province, which is tested by measuring physical characteristics of natural phenomenon. The resulting data are reduced, analyzed, and interpreted to locate expressions or responses associated with possible ore bodies. The process is, in fact, repeated in ever increasing measurement detail to increase the accuracy and precision of information for decision making. Exploration ceases when management makes the decision to develop a mineralized area, to hold a property for more favorable market conditions, or to drop a property because it is not economically viable.

Jan 1, 1979

By Anibal Gajardo

Because of the Chilean Ministry of Mining's interest in the development of industrial minerals, the Chilean Geological and Mining Service (Servicio Nacional de Geología y Minería, SERNAGEOMIN) has carried out a research program during the last two years to identify projects that represent interesting investment opportunities for small- to medium-scale operations in Chile. Most important of these projects are: (1) Quebrada Lluta aluminum sulphate, for drinking- and industrial-water treatment, with a potential domestic and foreign mar- ket of almost 43,000 tonnes per year and investments of about US$1.8 million; (2) Quebrada Lluta-Quebrada Cardones pumice, for abrasives, filters, fillers, and light- weight aggregates, with a potential market of about 30,000 tonnes per year, and in- vestments of US$2.0 million; (3) El Maule dolomite, for soil conditioner and iron smelting, with a total potential domestic market of some 60,000 tonnes per year, and estimated investments of US$2.0 million; (4) Las Escaleras bentonite, for animal feed, pelletising, and oil absorbents, with a potential market of almost 6,000 tonnes per year, and investments of about US$2.4 million; (5) Laraquete-Carampangue andalucite, for alumina refractories, with a future total domestic and foreign demand of about 15,000 tonnes per year, and estimated investments of US$2-2.5 million; (6) Rio Lía garnet, for fillers and sand-blasting abrasives, whose domestic market represents 10,000 tonnes per year, with investments of US$2.3 million; and (7) Munilque pumice, for building bricks and panels, with a potential domestic market of 250,000 tonnes per year, and investments of US$1.4 million. The development of these projects will represent an important increase and a significant diversification in Chilean industrial-minerals production.

Jan 1, 1999

By Chas. E. Shumate

There is assembled here this morning in Chicago the heartland of America, what is undoubtedly the greatest concentration of Technical, Scientific and "CAN DO" knowledge ever assembled in America. The participation in this Conference by the representatives of so many nations is particularly impressive and is a further indication of the importance of the subject matter of this conference which you will be discussing in much detail during the next few days. Another impressive feature of this Conference is the participation of a large segment of the construction industry in whose hands fall the job of building what others design. Also strongly represented is the manufacturing industry whose capability is well known throughout the world. They have the resources to design, develop and manufacture the machines and specialized equipment needed to do any job which the world requires. You should not expect to gain any knowledge from my few remarks this morning as I am undoubtedly the least qualified individual in this room on the highly technical and scientific subjects you will be discussing during these next few days. However, I shall offer a few broad suggestions on subject matter which I trust may generate serious thought during your discussions.

Jan 1, 1997

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982