Search Documents

By A. K. Majumder

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of coal fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of coal fines. The results obtained from this study revealed that among the parameters studied, drum rotation and feed solids concentration play dominating roles in controlling the yield and ash content of the clean coal. Mathematical modeling equations that correlate the variables studied and the yield and ash contents of the clean coal were developed to predict the performance of an MGS under different operating and design conditions. The entire exercise revealed that the MGS could produce a clean coal with an ash content of 14.67% and a yield of 71.23% from a feed coal having an ash content of 24.61%.

Jan 1, 2007

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

The Mining Foundation of the Southwest (MFSW)promotes public understanding and education related to the mining industry. Towards this goal, the Foundation has funded several projects from donations and fundraising activities. The MFSW was incorporated in 1993 by combining the Mining Club of the Southwest and the Mining Club of the Southwest Foundation. The Mining Club began in 1971 as a social organization. It provided members of the mining community an opportunity to meet. The club also provided a means for public education about mining. In the early 1990s, the club’s efforts were directed mainly toward educational activities. And in 1992, discussions began concerning incorporation into a non-profit foundation to further the public understanding of mining. In 1983, the American Mining Hall of Fame was inaugurated to honor significant contributors to the industry and profession. The Hall of Fame serves to educate people about prominent persons associated with the mining industry, present and past. The honorees number 75. Plaques commemorate their induction and are on display at the Arizona Historical Society’s Museum in Tucson, AZ. The combined honors ceremony and banquet have remained one of the fund raising activities.

Jan 1, 1999

By Se-joon Kim, Jong-hwa Chun

"‘Gas hydrate’ is the common term for a solid material formed from the combination of various gases as ‘guest’ and water as ‘host’. A series of large-scale scientific drilling and coring programmes conducted since 2000 revealed that natural gas hydrate exists in a wide variety of accumulations in the sediments. The scaled-up onshore and offshore field production tests during the last decade show that gas production technology will be realized to make gas production from gas hydrates viable in the future, recognizing its potentials as one of the future sustainable energy resources.The total produced gas was approximately 470 m3 by the hot water circulation method over 6 days of operation in the permafrost-associated Mallik 2002 project in the Mackenzie Delta of Canada. In the Mallik 2007-2008 project, the gas was successfully produced stably by the depressurization method for 6 days, up to 13,000 m3 cumulatively. The depressurization method applied in the Mallik test was shown to be an effective way to produce gas from gas hydrates. The Alaska field trial to inject mixed gas of CO2 and N2 to exchange CH4 in 2012 was successfully done for the first time to produce maximum 1,270 m3 per day. A remarkable achievement was made by Japan when it completed its first offshore production test in the Eastern Nankai Trough, producing approximately 120,000 m3 of methane by the depressurization method over 6 days in March 2013. The technical challenges and scientific uncertainties obtained from Nankai Trough production test provide Korea with more considerations as to the aspects of well completion, reservoir formation and seafloor stability, sand control, flow assurance, environmental monitoring, and etc., due to the different geological setting and geomechanical properties of the Ulleung Basin in Korea."

Sep 1, 2014

Construction of the Boddington Mine 130 km (81 miles) southeast of Perth, is about 89 percent complete. When the $2.9-billion development is finished, it will be the largest gold mine in Australia, producing 31 t/a (1 million oz/year), according to project majority owner Newmont Mining. Newmont?s acting regional group executive for Asia Pacific, Philip Stephenson, told a gold conference in Australia that the project would be ?the biggest thing for Newmont this year.? The project has been in the works for more than 10 years, but because of a three-sided ownership and fluctuating gold prices, it struggled to get started. However, Newmont is set to become the full owner of the project and is moving ahead on the low-grade project. ?We are targeting annual production of 31 t/a (1 million oz/year) for each of Boddington?s first five years. When it is in full production, Boddington will be the largest gold mine in Australia,? Stephenson said. ?The mine?s costs applicable to sales will be around US$9.64/g (US$300/oz) and that puts Boddington into the bottom quartile of the global cost curve. ?Strategically for Newmont, Boddington coming on-line will improve Newmont?s overall global geopolitical risk profile as it delivers greater exposure to an AAA-rated country.? Boddington has a projected mine life of 20 plus years. It has current total reserves of 622 t (20 million oz) and rising. Stephenson said Boddington has the largest reserve base of all gold projects in production or those that are about to go into production in A-rated countries or better. And it will be an important asset for many years to come. Newmont will acquire the remaining 33 percent share held by AngloGold Ashanti in a deal that should be concluded in the next two months. Australian miner Newcrest Mining Ltd. had exited the joint venture several years ago. Newmont had come into the project through the take-over of then Australia?s leading gold miner Normandy Mining, while AngloGold Ashanti gained entry through

Jan 1, 2009

By B. K. Belle

The beginning of 21st century has heralded the global strategic importance, as evidenced by increase in energy prices and energy generation-emission-utilization dilemmas. In January 2008, the South African energy supplier, ESKOM had tabled the concept of power conservation and acknowledged the energy crisis until 2016. The concept is required of all energy users to reduce their electricity consumption, intensify energy efficiency and cautiously proceed with new projects. The generation of energy results in by-products called ?green house gases? (GHGs). To make a positive response to climate change and their effect on the environment, every energy user must ensure efficient energy use through technical and administrative means referred to generally as energy savings. This paper identifies mine ventilation engineering, in particular the electricity consumed by main fan units, as an area of potential energy savings. For a major mining company, electricity consumed by main ventilation fans alone can be in the order of 120 MW. Although a known fan engineering technique but scantly applied technology identified as the Hermit Crab can be seen as a ?quick win? project, due to its success in other industries such as cement and steel. The ?Hermit Crab? technique® involves upgrading or replacement of an impeller - whatever its origin - with a design impeller to suit the actual ventilation requirements, resulting in increased fan efficiencies. The cash flow benefits associated with a case study and its rollout of this technology have been calculated. For a 10% increase in main fan efficiency, would have a net present benefit of US$ 16.08m over 10 years. With the inclusion of carbon credits, this benefit rises to US$ 29.40m in total. Application of other available technologies, viz., composite materials, ventilation-on-demand and variable speed drives are discussed.

Jan 1, 2009

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By W. A. Vine

Next year, in 1964, Butte will celebrate its Centennial. It was in May, 1864, that the first recorded mining activity took place. During that summer, several rich placers were found on Silver Bow Creek and its tributaries, and a gold rush followed. As placer mining proceeded in the creek beds, the quartz lodes on the hillsides were located and the veins were prospected. Mining in Butte entered its second phase when the rich silver mines, the Alice, Moulton, and Lexington, were opened. The silver boom lasted until the decline in the price of silver in the early 1890's forced the closure of many of the mines. An indication of the beginning of the copper mining era in Butte was in 1866 when it was noticed that green copper carbonate discolored some of the, lode material. It was not until ten years later, however, that the Anaconda and St. Lawrence claims were located by Michael and Ed Hickey. The claims were sold in 1880 to Marcus Daly and in 1881, Daly obtained financing and organized the Anaconda Silver Mining Company to exploit the vein The silver venture was a failure because of the predominance of copper which diluted the bullion to only 400 fine.

Jan 1, 1963

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By M. K. Mohanty

Over the years, screen bowl centrifuges have been widely used for dewatering fine coal in coal preparation plants in the United States and elsewhere. Its popularity is attributed to its relatively low cost, its high capacity of providing low moisture content product and its relative ease of operation and maintenance. It is generally recognized in the engineering and scientific communities that screen bowl centrifuges provide some degree of particle size separation while dewatering fine coal in a common application. However, the extent of differential partitioning of coarse and fine particles achievable by a screen bowl centrifuge has not been systematically studied in the past. The present investigation was aimed at conducting a parametric study using a statistically designed experimental program to better understand and optimize the size classification performance of a screen bowl centrifuge. A continuously operating screen bowl centrifuge having a bowl diameter of 0.5 m was used for this study at the Illinois Coal Development Park. Three key operating parameters, i.e., feed flow rate, feed solid content and pool depth, were varied to conduct a total of 17 experiments using a three-level factorial test matrix. Some of the best size separation performances achieved in this study may be described as having an imperfection value of 0.13 at an effective separation size (d50c) of 38 µm and an imperfection value of 0.27 at an effective separation size (d50c) of 2.8 µm. Due to an effective separation of ultrafine high ash materials, the ash content of the screen bowl feed was reduced from 22.3% to a minimum of 8.84% with a combustible recovery of 84.1% and an ash rejection of 71.6%. A higher combustible recovery of 92.1% was achieved at a product ash content of 12.5% with a d50c of 2.8 µm and imperfection of 0.27.

Jan 1, 2008

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

Compagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation. Tailings are stored in a ?fine? pond. Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and rainforest meteorological conditions). It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility. Therefore, CME asked Caspeo to: ? Carry out an on-site flotation pilot campaign. ? Design an industrial flotation circuit. The tailings reprocessing will contribute to a better tailings management and a dry up of the gold resource, limiting the risk of illegal mining after remediation of the CME site. CME MINE The Esperance gold mine is located in French Guyana, in the vicinity of several gold deposits as Omaï, Rosebel or Camp Caïman, holded by Iamgold and Newmont. These main gold deposits are located on the figure 1. Esperance was put into operation in the early 90?s. The first years were devoted to the mining of alluvial gold in the gravel of the Esperance Creek. Since then, operation was led in the primary gold deposit. Annual production is on average 254kg for a total production in fifteen years of 4300kg. Geology Esperance deposit is located in the greenstone belt of the Guyana Shield. Mineralization is in tectonic contact between sedimentary basin of Maroni and a granitic massif. Clastic series, composed of conglomerate and lamina sandstone, overlie a volcano-sedimentary basement (series called "Paramaca"). The area is strongly folded by shear movements, resulting from granite deposit. Gold is in interlacing quartz veins intersecting the clastic series. Gold is present in association with pyrite. Other elements, as silver or arsenic, are in negligible quantity. Exploitation The Maroni River is the only access to the Esperance mine. Only the saprolite and a part of the transition rock are extracted in the open pit. Excavation works are done using shovels Hyundai 450 (4 units) and haulage works using articulated dumpers Terex TA35 (4 units). These two sorts of equipments are presented figure 2. Mill The mill is composed of crushing and grinding processing plants. After gravity concentration, both plants produce tailings that are stored in two ponds: the first pond contains coarse product which segregates the particles crushed to 2mm upstream and settled clays downstream; the second pond contains the fine product made of particles ground to 200µm. These two ponds, bordered by dams and diversion canals, are located on former alluvial sites of Esperance Creek (see figure 3). [ ] The CME mill is currently producing gold concentrate, with a global recovery of about 67%. The ore is crushed by one jaw crusher and two hammer crushers. The ore then passes through a Knelson KC 48 gravity concentrator, producing a first gold concentrate. The

Jan 1, 2009

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001