Search Documents

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By J. Brune

The disaster at the Upper Big Branch (UBB) mine 2010 has demonstrated the destructive violence of a coal dust explosion by killing 29 miners in the worst mining accident the United States has experienced in almost 40 years. This explosion brought to light that the United States mining industry must strengthen explosion prevention and explosion hazard detection practices. Recent legislation such as the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) pushed the strengthening of explosion and disaster response and miner protection in addition to stricter regulations on the sealing of abandoned areas and on conveyor belt flame resistance. The focus of this new act was on how to respond to a disaster or explosion, yet not much improvement was made with respect to prevention explosion disasters. Researchers at the Colorado School of Mines have recently concluded extensive research into methane and coal dust explosion prevention practices and regulations as it may be applicable to underground mines in the United States. This research aims to forward more studies into the use and adoption of standards and procedures that have been utilized in countries with strong explosion prevention histories.

Feb 23, 2014

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Despite numerous empirical, numerical, and hybrid studies conducted on the subject of coal rib failure, mine fatalities related to rib failures continue to occur. To date, a standard methodology for the design of coal rib supports which can accommodate the wide range of unique conditions found in coal mines in the United States has not been developed, forcing mine operators to rely on the trial-and-error process or industrial legacy practices for the design of coal rib support patterns. In this study, to better understand the support systems' effectiveness, various rib bolting scenarios were investigated. A coal mass constitutive model is implemented to a Distinct Element Method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength-reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid Banded-Bright coal (BBC) were considered in this study. Different scenarios such as rib bolt length and the number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength reduction method in DEM code with the coal-mass model can aid in the development of practical primary support charts, which can help in the rib support design process. In addition, an unsupported RibFOS cutoff

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By M. Scaggs, K. Phillips

"Coal Worker’s Pneumoconiosis (CWP) is an occupational lung disease caused by chronic exposure to respirable mine dust. After decades of steady decline, CWP incidence appears to be on the rise since the mid-1990s, particularly in some regions of Appalachia. Alarmingly, many of these cases have rapidly progressed to the most advanced form of CWP, referred to as Progressive Massive Fibrosis (PMF). Most of what is currently understood about respirable mine dust has been gleaned from routine regulatory monitoring, which tracks total mass concentration of respirable dust (mg/m3) and, less frequently, silica mass content. This paper focuses on the use of thermogravimetric analysis (TGA) as a way to provide basic characterization of the whole composition of the dust, allowing it to be classified into three mass fractions – coal, carbonate, and non-carbonate minerals. TGA was conducted on 59 dust samples collected by miners from eight coal mines in central Appalachia, and the results are discussed in terms of differences between mines, regions, and primary occupations. Consistent with prior results on area dust samples from some of the same mines, results of the personal samples generally show that the coal mass fraction of the dust is relatively low. Carbonate and non-carbonate minerals thus tend to make up the bulk of the dust mass, and vary across occupations and specific mines. INTRODUCTION After nearly four decades of decline, the prevalence of Coal Workers’ Pneumoconiosis (CWP, or “black lung”) in the US has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of progressive massive fibrosis (PMF), which is the most advanced form of the disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 US coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85%) that had a normal radiograph on file to use as a baseline, 27 (17%) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84%) of the individuals in that study worked in KY, WV or VA, and 169 (88%) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern KY. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, these recent reports may well overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression – such that effective interventions can be devised."

Jan 1, 2018

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies. REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows."

Jan 1, 2018

By Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity', innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1984

By Victor L. Steven

10.1-SHAFT SINKING AND RAISING BY CONVENTIONAL METHODS VICTOR L. STEVEN 10.1.1-SHAFT SELECTION A great deal of thought and planning should go into the selection of a mine shaft to provide the most effective use over the greatest, period of time. It sometimes is better to make an additional capital expenditure in the initial shaft program to achieve the greatest overall shaft usage. It is possible to sink a shaft which could be used for mine development, and initial production and later convert it to a ventilation, service or escape shaft. It is important to consider a second shaft in the original planning to provide ventilation, an escapeway and services for overall efficient production and safety. A second shaft usually is required to comply with state and federal mining laws. The main items to consider in shaft selection are: 1. Installation from surface or underground. 2. Vertical or inclined (sec Sec. 10.1.4L for discussion of factors involved in choice). 3. Tonnage to be hoisted. 4. Size of mining equipment to be lowered through the shaft to the underground workings. 5. Amount of water to be handled in the mining operation. 6. Ventilation requirements. 7. Type of ground the shaft is to be sunk through. 8. Position of shaft with relation to ore body. After the main features of a shaft arc determined, such as vertical or inclined, shape, size, type of lining and support, compartments, and shaft. facilities (air, water, ventilation, pump lines, power cahles, etc.), then :I sinking plant and procedures should be planned. At this point it should be decided whether the company will sink the shaft with its own crews or award the job to a competent shaft contractor. Company sinking generally will cost less if competent shaft men are available. Money also will be saved in plant costs, such as for hoist, headframe, compressed air, buildings, etc., as these will be part of the permanent plant and can be used in the sinking operation. Labor costs generally will be lower than contractor construction rates. The advantage of having a contract, or is the speed of completion of the project. Contractors usually have headframes and hoists ready to move on the job immediately and have trained crews ready to complete the project in the shortest possible time. Next, the type of surface sinking plant (hoist, headframe, etc.) should be selected and a determination made whether it is to be temporary or permanent. In most cases it is less expensive to install the permanent, headframe and hoist, and use them for sinking. The type of actual sinking equipment to be used should be evaluated for the most efficient sinking cycle, e.g., mucking method, drilling method, and lining or support means. The proper cycling of drilling, mucking and lining is extremely important in obtaining the most favourable sinking costs. 10.1.2 - GROUND STABILIZATION AND WATER CONTROL Prior to the shaft-sinking operation an investigation should be made into ground-water conditions. If water is anticipated, then pregrouting of the ground

Jan 1, 1973

By Donald E. Ralston, V. Rajaram, Michael N. Greeley, John W. Peters, Terry J. Laverty, F. S. Kendorski, Peter G. Chamberlain, J. Brent Hiskey, William C. Larson

Preliminary figures from the US Mine Safety and Health Administration show 801 underground metal mines and 490 surface metal mines, at the end of 1981, up from 663 and 383, respectively, in 1980. Preliminary MASH figures also show 207 underground nonmetal mines and 1070 surface nonmetal mines at the end of 1981, compared with 167 and 1092, respectively, last year. In addition, preliminary MASH figures show there were 14,676 mineral extraction operations on the surface and 3845 underground at the end of 1981, versus 14,951 and 3675, respectively, for last year. The number of mines, then, in three of four categories increased significantly, while having a lower net total of just 2% in the other category. And the number of underground extraction operations increased nearly 5% for the year, while surface operations were down less than 2%. But despite operations totals that mostly held their own or showed significant increases, it was a tough year for the nation's mining industry. The nonferrous segment of the industry had a bad year and 1982 may be no better, according to Business Week (Jan. 11, 1982), which adds that a turnaround is impossible unless the general economy recovers. Even then, with diminishing markets and overcapacity plaguing its products, the mining industry's condition "will be far from robust," the magazine says. The basic problem is that nonferrous metals-aluminum, copper, lead, molybdenum, nickel, and zinc-are tied to the most troubled sectors of the US economy. As recently as 1979, for example, more than 40% of all aluminum shipments went to the construction and transportation industries. Last year, these markets were down to 35% of aluminum shipments. And molybdenum sales to steel producers dropped by nearly 15% last year. Moreover, nonferrous products ended 1981 at disastrously low prices. Molybdenum oxide sold at $8.77/kg ($3.98/lb), half its $17.63/kg ($8/lb) price earlier in 1981 and aluminum was listed at $1.08/kg ($0.49/lb), compared with $1.54/kg ($0.70/lb) a year earlier. The Comex price of copper was $1.54/ kg ($0.70/lb), down from $3.11/kg ($1.41/lb) in early 1980, in real terms the worst copper price in 30 years. Lower prices led operators to cut their output and increase layoffs, shut down mines, and defer capital spending projects. In December, Duval Corp., a Pennzoil Co. subsidiary, shut all four of its US copper mines until March. Aluminum Co. of America had laid off 7.3% of its work force, shut nine of its 38 smelting lines, and entered 1982 operating at only 68% of capacity. Inco Ltd., the Free World's largest nickel producer, lost money in 1981, an estimated $11 million, for the first time since 1932. And, like Falconbridge Nickel Mines and other major nickel producers, had cut back on nickel production and was operating at only 63% of capacity (Forbes, Feb. 15, 1982). Amax, the country's largest molybdenum producer, had cut production by 20%. And Hanna Mining Co. sold lead for $5.07/kg ($2.30/lb), about $1.54/kg ($0.70/lb) below what it cost to produce. Another problem is that copper companies in the next few years must come to terms with problems of aging smelters. Some companies are simply closing them. In 1980, Anaconda closed its 75-year-old Butte, MT, smelter and is shipping concentrates to Japan, rather than modifying the smelter to meet environmental requirements. And oth Phelps Dodge Corp. and Asarco Inc. have antiquated smelters on which they will have to make decisions. The most troubled metal in 1982, Business Week said, will be molybdenum, with no real recovery in sight until the mid-1980s. High molybdenum prices in the late 1970s, caused in part by shortages, triggered overexpansion that will take years for the US market to soak up. On a more upbeat note, 1981 mergers might help stabilize the industry by providing funds for mining companies. Standard Oil Co. (Ohio) said it plans to spend $7 billion on Kennecott during the next 10 years for modernization and expansion. And Atlantic Richfield Co. said it will spend $500 million on Anaconda Copper Co. during the next five years. Another positive note was sounded by T. H. Adams of the United Banks of Colorado Inc. He said he expects the mining industry to experience moderate growth in 1982, led by "interest rate sensitive" demand from energy, electronics, and defense markets. And mining will be helped by "weak, but improved" construction and auto markets. The mining industry will be operating in an economy stronger than 1981, but still relatively sluggish by postwar standards, Adams predicted. Iron Ore Estimated US iron ore production in 1981 was 75.2 Mt (74 million long tons), up 6% from 70.7 Mt (69.6 million long tons) in 1980, though down from the 87.1 Mt (85.7 million long tons) produced in 1979. The mine value of usable iron produced from domestic mines was estimated at $3 billion. US iron ore was produced by 28 companies operating 35 mines, 26 concentration plants, and 16 pelletizing plants. The mines included 34 open pits and one underground mine. Byproduct ore recovered from copper- and titanium-mining operations accounted for less than 1% of total iron ore production. Fifteen mines operated by nine companies accounted for 94% of total

Jan 5, 1982

By M. H. Bolu

Since undergoing a major mill expansion in 1979, Canada Tungsten Mining Corporation Limited has successfully operated a somewhat unconventional rod mill/rod mill grinding circuit at its mill in Tungsten, N.W.T., Canada. The concentrator employs two rod mills in series, of unmatched size and horsepower, for production of feed to a gravity (tabling) circuit. Cyclones and screens are closed circuited with the secondary rod mill. Outlined in this paper are the rationale behind, and consequences of operation of this unusual grinding and classification configuration.

Jan 1, 1984

By Sebastian Avalos, Julian M. Ortiz, Willy Kracht

Semi-autogenous grinding mills play a critical role in the processing stage of many mining operations. They are also one of the most intensive energy consumers of the entire process. Current forecasting techniques of energy consumption base their inferences on feeding ore mineralogical features, SAG dimensions, and operational variables. Experts recognize their capabilities to provide adequate guidelines but also their lack of accuracy when real-time forecasting is desired. As an alternative, we propose the use of real-time operational variables (feed tonnage, bearing pressure, and spindle speed) to forecast the upcoming energy consumption via machine learning and deep learning techniques. Several predictive methods were studied: polynomial regression, k-nearest neighbor, support vector machine, multilayer perceptron, long short-term memory, and gated recurrent units. A step-by-step workflow on how to deal with real datasets, and how to find optimum models and final model selection is presented. In particular, recurrent neural networks achieved the best forecasting metrics in the energy consumption prediction task. The workflow has the potential of being extended to any other temporal and multivariate mineral processing datasets.

Jun 16, 2020

By N. C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U. S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, preliminary results, and remediation ideas based on field observations are presented in this paper.

Jan 1, 1995

Passive seismic monitoring is a useful tool for measuring wave propagation in rock mass in deep underground mining. About 20000 mining ? induced seismic events of a hard rock mine, are identified and investigated. The travel times of source-receiver pairs allow us to demonstrate temporal change in velocity. It was found that the average P wave velocity is about 6000 m/s in the mining regions. Velocity investigations on the data during about three months around the main shocks show a significant decrease of the average seismic wave velocity after the main shocks. The sudden drop of average velocity change after the main shocks implies the creation of new fractures in the rock mass due to the main shocks. Afterward, the average velocity increased to a normal level after a time duration of several days. A reasonable explanation for the post seismic velocity increase is that opened cracks begin to close due to crack healing.

Feb 23, 2014

By Robert M. Cox

Surface mining of coal in the South developed into a major industry during the 1960's. The economic significance of the industry is much greater than is readily apparent when one considers only the value of the coal mined. The abun-dant supply of relatively inexpensive steam coal for electric power generation that has been derived from the surface mines has provided the foundation for the industrial expansion that has occurred throughout the South. The region, in gen-eral, has enjoyed the benefits of plentiful low cost electric power. However, re-cent political decisions, at all levels of government, threaten to destroy or severely curtail the surface mining of coal and eliminate the economic advantages once enjoyed by the region. These political decisions are rapidly changing the basic rules of operation and fundamental economics of surface coal mining. Recent changes, resulting from the enactment of environmental and health and safety laws and various bureaucratic rules and regulations, have had a three-fold effect: 1) Greatly increased operating cost, 2) increased lead times for mine development, 3) limited potential reserve base for future mining. Also current legislative proposals are casting a shadow of uncertainty over the future of all coal mining operations that has created serious delays and in-creased cost for the expansion of the coal industry necessary to meet our project independence goals. Technology Surface mining is the safest and most economical way to produce raw materials from the earth's crust. It also affords a more healthier working environment for the individual miner. Surface coal mining now accounts for more than 60 percent of the annual coal production in the South. Surface mining of coal requires the removal of the overburden to expose the

Jan 1, 1977

By S. K. Jena, S. Singh, B. Das, N. Dhawan, P. K. Misra, D. S. Rao

"Iron as an impurity in pyrophyllite ore affects pottery, ceramics and tile quality. We carried out the characterization of a pyrophyllite ore sample using optical microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and wet chemical analysis. The study revealed the presence of 2.15% iron oxide (Fe2O3 ) along with silica and alumina as the major components, which constituted around 90% of the total sample. We carried out the removal of iron from the pyrophyllite using magnetic separation and acid leaching and found that wet high-intensity magnetic separation (WHIMS) could remove 28% of iron values while oxalic acid leaching could remove up to 99.3%. The leaching kinetics of iron removal and the effects of pulp density, acid concentration, leaching time and temperature were also investigated. The optimum conditions for leaching were found to be leaching time of 60 minutes, temperature of 90°C, pulp density of 5%, oxalic acid concentration of 0.3 M, and particle size below 100 microns. Iron dissolution from the pyrophyllite sample can be best described by the diffusion of ions through the product layer of constant-size spherical particles. The breakdown of the pyrophyllite structure was evident from the FTIR and TGA studies. The activation energy of the leaching process over the temperature range was calculated to be 43.47 kJ/mol. IntroductionPyrophyllite is a naturally occurring phyllosilicate mineral composed of aluminum silicate hydroxide [Al2Si4O10(OH)2] as the major component and often associated with other minerals such as kaolinite, mica, quartz, rutile and epidote. It occurs in fine-grained sericite schist that is quarried as pyrophyllite (Pandit et al., 2008). In India, pyrophyllite occurs mainly in Madhya Pradesh state, Uttar Pradesh state and the Keonjhar district of Odisha state (Harpavat, 1995). Pure pyrophyllite is a highly desirable material for various applications due to its unique properties. It exhibits high refractive behavior, low thermalelectrical conductivity, low expansion coefficient, low hot-load deformation, low bulk density and high corrosion resistance to molten metal and basic slag (Rieger, 1997). It is used in the ceramics, refractory, foundry, electrical-insulation, sanitary-ware, glassmaking, pesticide and rubber fields. Compared with clay, it has lower thermal conductivity and coefficient of expansion, making it more suitable for refractory applications (Harben, 2002; The Minerals Yearbook, 2011)."

Jan 1, 2015

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2017