Search Documents

By R. Raymond

The occurrence and distribution of organic sulfur in coals may be investigated using electron probe microanalysis, scanning electron microscopy, and optical petrography. A general relationship exists between macerals and organic sulfur contents in individual coals: sporinite, resinite = micrinite, vitrinite > pseudovitrinite = semifusinite = macrinite > fusinite. With increasing organic sulfur content of a coal, the total range in organic sulfur content between macerals containing high and low organic sulfur contents likewise increases. Furthermore, the organic sulfur content of the vitrinite in most coals equals the organic sulfur content of the coal. For any individual coal, organic sulfur contents of macerals correlate inversely with reflectance-in-oil measurements, but the amount the organic sulfur contents vary between macerals cannot be calculated based solely on the coal's rank. Formation of pyrite following peatification has no effect on organic sulfur contents of surrounding macerals.

Jan 1, 1986

By N. A. Abdel-Khalek

An experimental study was carried out to compare the results of laboratory column flotation versus conventional flotation for the cleaning of fine coals of different rank and their oxidized samples as well as discrete size fractions. Surface oxidation caused a significant reduction in the flotation yields achieved with both methods. However, the column flotation produced concentrates? of lower ash content. The recovery -size curve achieved with column was similar in shape to that obtained with conventional cell, with superior results in the region of fine fractions. The influence of some column operating parameters was also discussed.

Jan 1, 1990

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By B. W. Cavender

Capital investments are made for a variety of reasons, ranging from providing incremental capacity at existing operations to developing and implementing new technologies intended to radically improve a company's capabilities. These projects generate very different business opportunities and create value in distinctive ways. For incremental improvements, the capital budgeting process assures at least a loose fit between short-term goals and readily available resources. However, the criteria used to evaluate capital projects often prevent a company from committing to more aggressive goals, which lie beyond the firm's current abilities or resources. Such projects may not have clearly identifiable future cash flows, and the degree of interaction with other projects and the nature of the risk incurred may be difficult to estimate. Additionally, by focusing only on quantifiable benefits, the budgeting process often fails to recognize "soft" improvements such as increased operating flexibility or new knowledge generated by such projects. By rejecting these projects, the capital budgeting process may actually harm the company's future competitive position.

Jan 1, 1999

By Ben F. Dickerson

For a number of years in office bull sessions, I have not so jokingly discussed the engineering or management fiasco of the year or decade. Usually, governmental projects are in the vanguard, such as tanks that won't tank, or heavy water plants that don't produce heavy water, etc., etc., all to the flutter of the taxpayers' hundreds of millions, or billions of dollars. The mining industry has also brought forth a share of this type of fiasco. Ordinarily, due to lack of funds, not opportunity, the stockholders only stand losses of a few tens of millions. Little knowledge of these major errors gets to the outside world, for the ordinary stockholder is usually not very alert, and managements are extraordinarily adept at discreet midnight internments in the fine print of the footnotes of annual reports.

Jan 1, 1975

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By Nathaniel Arbiter

After almost 60 years of application in this country froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency, and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum--to mention only the most important metals occurring in the U.S. as sulphides--must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000 tons daily milling rate on copper ores. Table I (1) shows the trend in copper ore grades in U.S. in recent years:

Jan 1, 1970

By D. Donison

The practice of blasthole mining is typically applied in competent ground conditions, primarily because of the open stope dimensions. At Magma Copper -Superior Mine, a field pilot project was completed examining a variation of blasthole mining in poor ground conditions. The results were very encouraging not only from a technical viewpoint, but also productivity viewpoints. This paper describes the pilot project and the resulting implications.

Jan 1, 1994

By Janet Briggs, Michael Vertes, J. F. Shirley, R. E. Cutherbertson, Alexander Sutulov, J. D. Vincent

Molybdenum, the 42nd element in the periodic table, is now a very important metal in industry of the United States and the world. Chemically, it is a very complex element having valences of 0, +2, +3, +4, +5, and +6, and can exist as a mixture of these valences in many compounds. It was discovered and separated by Scheele in 1778. At the present time, molybdenite is the only important commercial source of molybdenum. Molybdenum occurs in some 12-14 different recognized minerals, but practically all of the production is molybde¬nite. As late as 1915, it was considered a rare metal. Germany made extensive use of it during the first world war, which resulted in the establishment of a molybdenum industry in the United States at Cli¬max, Colo., in 1917. It was not until the mid-1920s when its introduc¬tion to steelmaking developed for the US automobile industry that the metal gained important acceptance. The first notable example was the Willis-Saint Claire automobile introduced in 1921 by C. Harold Willis, formerly chief metallurgist for Ford Motor Co. Molybdenum has also been produced in the US from wulfenite (PbMoO4) from Arizona and Nevada, and a small amount of molyb¬denite was produced up to the early 1970s as a coproduct from two molybdenum-bismuth mines in Quebec, Canada. The first byproduct production of molybdenite from a copper con¬centrating operation was achieved at Cananea, Sonora, Mexico, and was followed shortly by the Utah division of Kennecott Copper Co. in the mid-1930s. This section of the Handbook is divided into four main subdivi¬sions: Chapter 2, which deals with the concentration and recovery of molybdenite from primary molybdenum ores; Chapter 3, which deals with the recovery and separation of molybdenite as a byproduct from copper production; Chapter 4, which deals with the conversion practices employed for converting molybdenite to the oxide or metal form; and Chapter 5, which covers the uses of molybdenum in steel¬making, chemicals, pigments, lubrication, catalysts, etc. The Free World molybdenum production, for the past eight years from all sources, is shown in Table 1. 2. Primary Molybdenite Ores General In 1978 there were four primary molybdenite recovery plants in operation: Climax, Endako, Quests, and Henderson. For over half a century the Climax mine has been by far the largest and most important source of molybdenum in the world. During the early 1970s a few primary molybdenite mines in British Columbia were shut down due to adverse economical conditions. The largest of these was British Columbia Molybdenum, formerly owned by Kennecott Copper Corp. The Climax plant and operations are described in detail and the opera¬tions of the other plants are summarized following a general discussion of recovering molybdenite from primarily molybdenite ores. Recovery of molybdenite as a byproduct will be taken up in Chapter 3. Geology Molybdenite production from mines in which it is the sole or preponderantly important mineral is confined to ore bodies in granites or igneous-type rocks or pegmatite dikes. More than one state of mineralization is sometimes present as at Climax, York, Hardy, and Questa. In the case of Climax, important byproduct recovery of tung¬sten, tin, pyrite, and monazite is also attained. The molybdenite is commonly disseminated very finely in the siliceous granitic gangue but does occur in stringers and blebs in silicified mineral solution channels. Treatment of Primary Molybdenum Ores All primary molybdenum ores are low in molybdenite, the content ranging from less than 0.20% MoS2 to a high of about 0.40% MoS2. A high resistance to grinding is a common ore characteristic combined with a habit of very fine dissemination of molybdenite in the siliceous portion of the ore. Because of low MoS2 content, high hardness, and fine dissemination of molybdenite in primary ores, it has been necessary to develop a special mill treatment which yields an accepta¬ble recovery at a reasonably low milling cost. Essentially, the treatment consists of intensive rougher flotation at a relatively coarse grind with production of a low grade rougher froth containing a substantial percentage of the molybdenite in the form of low grade middling particles, followed with multistage regrinding to liberate the locked molybdenite and several stages of flotation cleaning to produce a finished grade concentrate. Rougher flotation on pulp ground to ap¬proximately 35 mesh is common practice, even if complete liberation of molybdenite from siliceous gangue may require regrinding to 200 mesh. The flotation of middling particles with a very low content of molybdenite in the rougher flotation step has been made possible by the application of a combination of reagents first developed at the Climax mill and used with some modification in the treatment of all primary molybdenum ores. The reagents commonly employed and their functions in flotation are:

Jan 1, 1985

By Q. Xiao, R. Naidu, W. Li, S. Song

Acid mine drainage (AMD) derives from the oxidation of sulfide minerals, primarily pyrite (FeS2), and is the most severe environmental issue facing the minerals industry. The most common short-term approach to AMD treatment is migration control, such as acid neutralization and metal/metalloid and sulfate removal, through the addition of alkaline materials, including lime (Ca (OH)2), limestone (Ca CO3), gangue minerals and industrial wastes. This requires the continuous input of materials and may result in the production of a vast amount of secondary sludge requiring further treatment and disposal. Addition of chemicals is usually more important in metal/metalloid removal than in sulfate removal unless the sulfate is present in very high concentrations. A more promising long-term strategy for AMD prevention is source control through the complete removal of pyritic minerals and encapsulation of potential risk minerals by coating with impermeable surface layers. This is regarded as the most cost-effective approach, although the mechanisms underpinning this and the implementation procedures are yet to be fully elucidated. It is likely that long- and short-term practices can be combined to optimize the remediation of contaminated mining sites. Some factors such as differing geological and mineralogical characteristics and transportation costs must also be considered for the successful implementation of AMD prevention and remediation strategies. This review also considers some implications for AMD remediation, but the promising bioremediation of AMD is not discussed as it has been extensively reviewed.

By Baron Miya, Keith Hanks, William Edgerton, Francis Fong

The City of Los Angeles capital improvement program includes the construction of a new 35-km interceptor sewer. This sewer will be built as a deep tunnel with finished diameters ranging from 2- to- 4 meters. The project will be constructed concurrently in two phases; an 18-km East-West and a 17-km North-South segment. The new sewer provides additional conveyance capacity for an existing deteriorating sewer that is scheduled for rehabilitation. Large sewage spills during the El Niño storms of 1998 resulted in a Cease and Desist Order that established an aggressive schedule for the completion of the project.

Jan 1, 1999

By Bruce R. Sutherland, Jim B. Ramsden, Gerry L. Bolton

Conductive metal powders are important building blocks for today's micro-electronic circuitry. Formulated into inks, they provide the interconnects needed to complete a complex integrated circuit and the means to enter the world of miniaturization. Traditionally, the inks have been based upon expensive metals such as silver, palladium, platinum and gold because of their excellent electrical conductivity and resistance to corrosion and oxidation. The use of a copper based ink, as an alternative to precious metal inks, recently has received considerable attention. Instability in the prices and limited supply of certain precious metal systems have driven up production costs, making the development of a lower cost copper system more attractive to manufacturers. However, lower production costs are on1 y real ized if performance and reliability can be maintained. While the development has been driven by cost, copper does offer some significant performance advantages over noble metal systems: conductivity as good as silver and 4W better than gold; leach resistance better than silver and equal to gold; stability at high frequencies better than gold or silver; strong film bonding characteristics; and compatibility with most solders. These benefits, however, do not come without cost. The inherently reactive nature of pure copper, while providing unique performance properties, makes it difficult to process. Unl i ke precious metals which can be fired in air, copper would oxidize and so requires special furnaces and atmospheres. Despite these difficulties, the transition from precious metal thick film systems to copper is gaining momentum. Manufacturers of high density, high performance circuitry are exploring the performance advantages of copper over gold and silver and the manufacturers of consumer products are considering the potential cost savings of copper over silver-palladium. Sherritt has developed a fine copper powder for this industry. Through association with the ink manufacturers, it has been found that performance properties of the ink vary with the physical and chemical characteristics of the powder. Production Process The production of very fine copper powders at Sherritt is based upon the disproportionation of cuprous ions as outlined in Equation [1] (1).

Jan 1, 1990

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

By J. A. Dos Santos

High angle conveyor (HAC®) systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency, (2) less dependency on petroleum products, (3) less sensitivity to inflation, (4) less labor, (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. Previous studies had revealed the technical and economic feasibility of high angle conveyors. This paper presents the Sandwich Belt HAC® as the vital link to optimization of in-pit conveying systems. HAC development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, to the first commercial unit in 1984, into "the latest commercial installations. Discussion continues with the HAC systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of HAC systems from the low capacity (up to 1,814 t/h), low lift (10.7 to 36.6M), highly mobile to the moderate capacity (1,814 to 3,629 t/h), moderate lift (36.6 to 76.2M), intermittently mobile to the high capacity (greater than 3,629 t/h), high lift (greater than 76.2M), semi-mobile, are discussed along with some possible combinations of these.

Jan 1, 1989

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By K. Avarmaa, P. Taskinen

"The solubilities of rhodium (Rh) in a molten silver alloy in doré-smelting conditions for treating copper refinery slime at temperatures of 1,000 to 1,300 °C were measured using a high-temperature equilibration-quenching technique and direct phase analysis by electron probe X-ray microanalysis. The results obtained indicate that the solubility of rhodium in molten silver is very limited: only 0.04 to 0.26 weight percent at 1,000 and 1,300 °C, respectively. The thermodynamic properties of rhodium in molten silver were estimated from the solubility data. The compositions of the solid rhodium alloys in equilibrium with molten silver-rich doré metal were also measured in this study. The excess rhodium in the doré alloy will precipitate during the refining as solid, greater than 99 weight percent Rh.IntroductionSilver refining is a core step of the processes of anode slime treatment and precious metals recovery in copper refineries (Hait, Jana and Sanyal, 2009; Ludvigsson and Larsson, 2003). It separates the oxidic materials, such as nickel oxide (NiO) and barium sulfate (BaSO4), from metallics after the de-coppering and de-selenation steps of the anode slime, and refines the silver bullion from the undesired elements present (Cooper, 1990; Hyvärinen, Lindroos and Yllö, 1989). Doré metal is a silver-rich alloy which after the smelting step will be refined electrolytically, and the remaining constituents of gold as well as the platinum group metals (PGM) will be subsequently recovered in their own processing stages.Because of low concentrations of PGMs in copper, they are typically soluble in the doré metal in anode slime treatment. This can be concluded from their binary phase diagram data with silver (Massalski et al., 2007). One exception is sometimes encountered in the anode slime smelting operations if the smelter feedstock is rich in rhodium, as may be the case if the raw materials contain secondary raw materials such as e-scrap. The solubility of rhodium in solid silver is less than 0.04 weight percent (Królas and Sternik, 1995), and its solubility in molten silver is highly uncertain. The only experimental information in the literature (Królas et al., 1993; Elliott, 1985) suggests that the silver-rhodium alloy system at 960 °C forms a eutectic, which locates less than 2 °C below the melting point of pure silver (Arblaster, 2015). Early observations (Rössler, 1900) propose that rhodium is insoluble in molten silver even if solid silver-rhodium solutions have been recently produced on a nanoscale (Kusada et al., 2010).The aim of this study is to measure experimentally the solubility of rhodium in molten silver at doré metal smelting and refining temperatures. The silver alloy used to mimic the doré alloy contained silver and about 1 weight percent of the alloying elements copper, gold, palladium, rhodium and tellurium. The experiments were carried out in metal-slag equilibria with nitrogen-oxygen mixtures as the atmosphere, employing an equilibration-quenching technique and using direct phase composition analysis by electron probe X-ray microanalysis (EPMA) (Jak, Hayes and Lee, 1995)."

Jan 1, 2017

By Rodrigo Peroni, Vitor Campos

Carajás is one of the largest open pit mines in the world. The mine is comprised by a haul road network more than 100 km long, where the need for good roads is paramount and determining of the truck performances. This work integrates, regarding the ultimate pit design, an approach to consider an economic value to an originally unfit material, assuming it has the appropriate characteristics for haul road construction, which sometimes lies over economic iron ore. This measure demonstrated an improvement in the utilization of resources and guarantee the necessary material to the haul road design and Mining Pads maintenance.

Jun 25, 2023

By William O. Rasmussen

Exploration requires processing highly varying kinds and amounts of geologic information. Successful discovery dictates that this be done quickly with maximum confidence. Most phases of exploration are more or less applicable to computer reduction on a routine basis. The use of digital computers to reduce raw data into interpretable form, lets the exploration geophysicist concentrate on interpretation and presentation, and to consistently apply more sophisticated and comprehensive analytical techniques, not practical before. In applying these concepts for the past several years, various efficient programs have evolved which provide more complete evaluation of all data including the pro- vision for more unique solutions. This has resulted in greater refinement and ability to select the most advantageous drill sites in a minimum time at a minimum cost or, in rejecting as soon as possible a project on which additional effort is no longer justified. Practical examples of computer applications in magnetics (air and ground), induced polarization and resistivity are discussed.

Jan 1, 1969

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980